1 /* 2 * Configuation settings for the Renesas Solutions ECOVEC board 3 * 4 * Copyright (C) 2009 - 2011 Renesas Solutions Corp. 5 * Copyright (C) 2009 Kuninori Morimoto <morimoto.kuninori@renesas.com> 6 * Copyright (C) 2010, 2011 Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> 7 * 8 * SPDX-License-Identifier: GPL-2.0+ 9 */ 10 11 #ifndef __ECOVEC_H 12 #define __ECOVEC_H 13 14 /* 15 * Address Interface BusWidth 16 *----------------------------------------- 17 * 0x0000_0000 U-Boot 16bit 18 * 0x0004_0000 Linux romImage 16bit 19 * 0x0014_0000 MTD for Linux 16bit 20 * 0x0400_0000 Internal I/O 16/32bit 21 * 0x0800_0000 DRAM 32bit 22 * 0x1800_0000 MFI 16bit 23 */ 24 25 #define CONFIG_CPU_SH7724 1 26 27 #define CONFIG_ECOVEC_ROMIMAGE_ADDR 0xA0040000 28 #define CONFIG_SYS_TEXT_BASE 0x8FFC0000 29 30 #define CONFIG_DISPLAY_BOARDINFO 31 #undef CONFIG_SHOW_BOOT_PROGRESS 32 33 /* I2C */ 34 #define CONFIG_SYS_I2C 35 #define CONFIG_SYS_I2C_SH 36 #define CONFIG_SYS_I2C_SLAVE 0x7F 37 #define CONFIG_SYS_I2C_SH_NUM_CONTROLLERS 2 38 #define CONFIG_SYS_I2C_SH_BASE0 0xA4470000 39 #define CONFIG_SYS_I2C_SH_SPEED0 100000 40 #define CONFIG_SYS_I2C_SH_BASE1 0xA4750000 41 #define CONFIG_SYS_I2C_SH_SPEED1 100000 42 #define CONFIG_SH_I2C_DATA_HIGH 4 43 #define CONFIG_SH_I2C_DATA_LOW 5 44 #define CONFIG_SH_I2C_CLOCK 41666666 45 46 /* Ether */ 47 #define CONFIG_SH_ETHER 1 48 #define CONFIG_SH_ETHER_USE_PORT (0) 49 #define CONFIG_SH_ETHER_PHY_ADDR (0x1f) 50 #define CONFIG_PHY_SMSC 1 51 #define CONFIG_BITBANGMII 52 #define CONFIG_BITBANGMII_MULTI 53 #define CONFIG_SH_ETHER_PHY_MODE PHY_INTERFACE_MODE_MII 54 55 /* USB / R8A66597 */ 56 #define CONFIG_USB_R8A66597_HCD 57 #define CONFIG_R8A66597_BASE_ADDR 0xA4D80000 58 #define CONFIG_R8A66597_XTAL 0x0000 /* 12MHz */ 59 #define CONFIG_R8A66597_LDRV 0x8000 /* 3.3V */ 60 #define CONFIG_R8A66597_ENDIAN 0x0000 /* little */ 61 #define CONFIG_SUPERH_ON_CHIP_R8A66597 62 63 /* undef to save memory */ 64 #define CONFIG_SYS_LONGHELP 65 /* Monitor Command Prompt */ 66 /* Buffer size for Console output */ 67 #define CONFIG_SYS_PBSIZE 256 68 /* List of legal baudrate settings for this board */ 69 #define CONFIG_SYS_BAUDRATE_TABLE { 115200 } 70 71 /* SCIF */ 72 #define CONFIG_SCIF 1 73 #define CONFIG_CONS_SCIF0 1 74 75 /* Suppress display of console information at boot */ 76 77 /* SDRAM */ 78 #define CONFIG_SYS_SDRAM_BASE (0x88000000) 79 #define CONFIG_SYS_SDRAM_SIZE (256 * 1024 * 1024) 80 #define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 16 * 1024 * 1024) 81 82 #define CONFIG_SYS_MEMTEST_START (CONFIG_SYS_SDRAM_BASE) 83 #define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 200 * 1024 * 1024) 84 /* Enable alternate, more extensive, memory test */ 85 #undef CONFIG_SYS_ALT_MEMTEST 86 /* Scratch address used by the alternate memory test */ 87 #undef CONFIG_SYS_MEMTEST_SCRATCH 88 89 /* Enable temporary baudrate change while serial download */ 90 #undef CONFIG_SYS_LOADS_BAUD_CHANGE 91 92 /* FLASH */ 93 #define CONFIG_FLASH_CFI_DRIVER 1 94 #define CONFIG_SYS_FLASH_CFI 95 #undef CONFIG_SYS_FLASH_QUIET_TEST 96 #define CONFIG_SYS_FLASH_EMPTY_INFO 97 #define CONFIG_SYS_FLASH_BASE (0xA0000000) 98 #define CONFIG_SYS_MAX_FLASH_SECT 512 99 100 /* if you use all NOR Flash , you change dip-switch. Please see Manual. */ 101 #define CONFIG_SYS_MAX_FLASH_BANKS 1 102 #define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } 103 104 /* Timeout for Flash erase operations (in ms) */ 105 #define CONFIG_SYS_FLASH_ERASE_TOUT (3 * 1000) 106 /* Timeout for Flash write operations (in ms) */ 107 #define CONFIG_SYS_FLASH_WRITE_TOUT (3 * 1000) 108 /* Timeout for Flash set sector lock bit operations (in ms) */ 109 #define CONFIG_SYS_FLASH_LOCK_TOUT (3 * 1000) 110 /* Timeout for Flash clear lock bit operations (in ms) */ 111 #define CONFIG_SYS_FLASH_UNLOCK_TOUT (3 * 1000) 112 113 /* 114 * Use hardware flash sectors protection instead 115 * of U-Boot software protection 116 */ 117 #undef CONFIG_SYS_FLASH_PROTECTION 118 #undef CONFIG_SYS_DIRECT_FLASH_TFTP 119 120 /* Address of u-boot image in Flash (NOT run time address in SDRAM) ?!? */ 121 #define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE) 122 /* Monitor size */ 123 #define CONFIG_SYS_MONITOR_LEN (256 * 1024) 124 /* Size of DRAM reserved for malloc() use */ 125 #define CONFIG_SYS_MALLOC_LEN (256 * 1024) 126 #define CONFIG_SYS_BOOTMAPSZ (8 * 1024 * 1024) 127 128 /* ENV setting */ 129 #define CONFIG_ENV_OVERWRITE 1 130 #define CONFIG_ENV_SECT_SIZE (128 * 1024) 131 #define CONFIG_ENV_SIZE (CONFIG_ENV_SECT_SIZE) 132 #define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN) 133 /* Offset of env Flash sector relative to CONFIG_SYS_FLASH_BASE */ 134 #define CONFIG_ENV_OFFSET (CONFIG_ENV_ADDR - CONFIG_SYS_FLASH_BASE) 135 #define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SECT_SIZE) 136 137 /* Board Clock */ 138 #define CONFIG_SYS_CLK_FREQ 41666666 139 #define CONFIG_SH_TMU_CLK_FREQ CONFIG_SYS_CLK_FREQ 140 #define CONFIG_SH_SCIF_CLK_FREQ CONFIG_SYS_CLK_FREQ 141 #define CONFIG_SYS_TMU_CLK_DIV 4 142 143 #endif /* __ECOVEC_H */ 144