xref: /openbmc/u-boot/include/configs/ea20.h (revision c0fb2fc0)
1 /*
2  * Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/
3  *
4  * Based on davinci_dvevm.h. Original Copyrights follow:
5  *
6  * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
7  *
8  * SPDX-License-Identifier:	GPL-2.0+
9  */
10 
11 #ifndef __CONFIG_H
12 #define __CONFIG_H
13 
14 /*
15  * Board
16  */
17 #define CONFIG_DRIVER_TI_EMAC
18 #define CONFIG_USE_SPIFLASH
19 #define	CONFIG_SYS_USE_NAND
20 #define CONFIG_DRIVER_TI_EMAC_USE_RMII
21 #define CONFIG_DRIVER_TI_EMAC_RMII_NO_NEGOTIATE
22 #define CONFIG_PREBOOT
23 
24 /*
25  * SoC Configuration
26  */
27 #define CONFIG_SYS_CLK_FREQ		clk_get(DAVINCI_ARM_CLKID)
28 #define CONFIG_SYS_OSCIN_FREQ		24000000
29 #define CONFIG_SYS_TIMERBASE		DAVINCI_TIMER0_BASE
30 #define CONFIG_SYS_HZ_CLOCK		clk_get(DAVINCI_AUXCLK_CLKID)
31 #define CONFIG_SKIP_LOWLEVEL_INIT
32 #define CONFIG_DA8XX_GPIO
33 
34 /*
35  * Memory Info
36  */
37 #define CONFIG_SYS_MALLOC_LEN	(0x10000 + 4*1024*1024) /* malloc() len */
38 #define PHYS_SDRAM_1		DAVINCI_DDR_EMIF_DATA_BASE /* DDR Start */
39 #define PHYS_SDRAM_1_SIZE	(64 << 20) /* SDRAM size 64MB */
40 #define CONFIG_MAX_RAM_BANK_SIZE (512 << 20) /* max size from SPRS586*/
41 
42 /* memtest start addr */
43 #define CONFIG_SYS_MEMTEST_START	(PHYS_SDRAM_1 + 0x2000000)
44 
45 /* memtest will be run on 16MB */
46 #define CONFIG_SYS_MEMTEST_END	(PHYS_SDRAM_1 + 0x2000000 + 16*1024*1024)
47 
48 #define CONFIG_NR_DRAM_BANKS	1 /* we have 1 bank of DRAM */
49 
50 /*
51  * Serial Driver info
52  */
53 #define CONFIG_SYS_NS16550_SERIAL
54 #define CONFIG_SYS_NS16550_REG_SIZE	-4	/* NS16550 register size */
55 #define CONFIG_SYS_NS16550_COM1	DAVINCI_UART0_BASE /* Base address of UART0 */
56 #define CONFIG_SYS_NS16550_CLK	clk_get(DAVINCI_UART2_CLKID)
57 
58 #define CONFIG_SPI
59 #define CONFIG_SYS_SPI_BASE		DAVINCI_SPI1_BASE
60 #define CONFIG_SYS_SPI_CLK		clk_get(DAVINCI_SPI1_CLKID)
61 #define CONFIG_SF_DEFAULT_SPEED		30000000
62 #define CONFIG_ENV_SPI_MAX_HZ	CONFIG_SF_DEFAULT_SPEED
63 
64 /*
65  * I2C Configuration
66  */
67 #define CONFIG_SYS_I2C
68 #define CONFIG_SYS_I2C_DAVINCI
69 #define CONFIG_SYS_DAVINCI_I2C_SPEED		100000
70 #define CONFIG_SYS_DAVINCI_I2C_SLAVE   10 /* Bogus, master-only in U-Boot */
71 
72 /*
73  * Network & Ethernet Configuration
74  */
75 #ifdef CONFIG_DRIVER_TI_EMAC
76 #define CONFIG_MII
77 #define CONFIG_BOOTP_DNS2
78 #define CONFIG_BOOTP_SEND_HOSTNAME
79 #define CONFIG_NET_RETRY_COUNT	10
80 #endif
81 
82 #ifdef CONFIG_USE_SPIFLASH
83 #define CONFIG_ENV_SIZE			(8 << 10)
84 #define CONFIG_ENV_OFFSET		0x80000
85 #define CONFIG_ENV_SECT_SIZE		(64 << 10)
86 #endif
87 
88 #if defined(CONFIG_VIDEO)
89 #define CONFIG_VIDEO_DA8XX
90 #define CONFIG_SPLASH_SCREEN_ALIGN
91 #define CONFIG_VIDEO_LOGO
92 #define CONFIG_VIDEO_BMP_RLE8
93 #define CONFIG_VIDEO_BMP_LOGO
94 #endif
95 
96 /*
97  * U-Boot general configuration
98  */
99 #define CONFIG_BOOTFILE		"uImage" /* Boot file name */
100 #define CONFIG_SYS_CBSIZE	1024 /* Console I/O Buffer Size	*/
101 #define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE /* Boot Args Buffer Size */
102 #define CONFIG_SYS_LOAD_ADDR	(PHYS_SDRAM_1 + 0x700000)
103 #define CONFIG_MX_CYCLIC
104 
105 /*
106  * Linux Information
107  */
108 #define LINUX_BOOT_PARAM_ADDR	(PHYS_SDRAM_1 + 0x100)
109 #define CONFIG_CMDLINE_TAG
110 #define CONFIG_SETUP_MEMORY_TAGS
111 
112 #ifdef CONFIG_CMD_BDI
113 #define CONFIG_CLOCKS
114 #endif
115 
116 #ifndef CONFIG_DRIVER_TI_EMAC
117 #endif
118 
119 /* NAND Setup */
120 #ifdef CONFIG_SYS_USE_NAND
121 #define CONFIG_MTD_DEVICE
122 #define CONFIG_MTD_PARTITIONS
123 
124 #define CONFIG_NAND_DAVINCI
125 #define	CONFIG_SYS_NAND_PAGE_2K
126 #define CONFIG_SYS_NAND_NO_SUBPAGE
127 #define CONFIG_SYS_NAND_CS		2
128 #define CONFIG_SYS_NAND_BASE		DAVINCI_ASYNC_EMIF_DATA_CE2_BASE
129 #undef CONFIG_SYS_NAND_HW_ECC
130 #define CONFIG_SYS_NAND_4BIT_HW_ECC_OOBFIRST
131 #define	CONFIG_SYS_NAND_USE_FLASH_BBT
132 #define CONFIG_SYS_MAX_NAND_DEVICE	1 /* Max number of NAND devices */
133 #endif
134 
135 /* SPI Flash */
136 #ifdef CONFIG_USE_SPIFLASH
137 #endif
138 
139 #if !defined(CONFIG_SYS_USE_NAND) && \
140 	!defined(CONFIG_USE_NOR) && \
141 	!defined(CONFIG_USE_SPIFLASH)
142 #define CONFIG_ENV_SIZE		(16 << 10)
143 #endif
144 
145 /* additions for new relocation code, must added to all boards */
146 #define CONFIG_SYS_SDRAM_BASE		0xc0000000
147 #define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_SDRAM_BASE + 0x1000 - \
148 					GENERATED_GBL_DATA_SIZE)
149 /*
150  * Default environment and default scripts
151  * to update uboot and load kernel
152  */
153 
154 #define CONFIG_HOSTNAME ea20
155 #define	CONFIG_EXTRA_ENV_SETTINGS				\
156 	"as=3\0"							\
157 	"netdev=eth0\0"						\
158 	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
159 		"nfsroot=${serverip}:${rootpath}\0"			\
160 	"rfsbargs=setenv bootargs root=/dev/nfs rw "			\
161 	"nfsroot=${serverip}:${rfsbpath}\0"				\
162 	"testrfsargs=setenv bootargs root=/dev/nfs rw "		\
163 	"nfsroot=${serverip}:${testrfspath}\0"				\
164 	"ramargs=setenv bootargs root=/dev/ram rw initrd="		\
165 	"0x${ramdisk_addr_r},4M\0"					\
166 	"mtdids=nand0=davinci_nand.0\0"				\
167 	"serverip=192.168.5.249\0"					\
168 	"ipaddr=192.168.5.248\0"					\
169 	"rootpath=/opt/eldk/arm\0"					\
170 	"splashpos=230,180\0"						\
171 	"testrfspath=/opt/eldk/test_arm\0"				\
172 	"nandargs=setenv bootargs rootfstype=ubifs ro chk_data_crc "	\
173 	"ubi.mtd=${as} root=ubi0:rootfs\0"				\
174 	"nandrwargs=setenv bootargs rootfstype=ubifs rw chk_data_crc "	\
175 	"ubi.mtd=${as} root=ubi0:rootfs\0"				\
176 	"addip_sta=setenv bootargs ${bootargs} "			\
177 		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
178 		":${hostname}:${netdev}:off panic=1\0"			\
179 	"addip_dyn=setenv bootargs ${bootargs} ip=dhcp\0"		\
180 	"addip=if test -n ${ipdyn};then run addip_dyn;"		\
181 		"else run addip_sta;fi\0"				\
182 	"addmtd=setenv bootargs ${bootargs} ${mtdparts}\0"		\
183 	"addtty=setenv bootargs ${bootargs}"				\
184 		" console=${consoledev},${baudrate}n8\0"		\
185 	"addmisc=setenv bootargs ${bootargs} ${misc}\0"		\
186 	"addmem=setenv bootargs ${bootargs} mem=${memory}\0"		\
187 	"consoledev=ttyS0\0"						\
188 	"loadaddr=c0000014\0"						\
189 	"memory=32M\0"							\
190 	"kernel_addr_r=c0700000\0"					\
191 	"hostname=" __stringify(CONFIG_HOSTNAME) "\0"			\
192 	"bootfile=" __stringify(CONFIG_HOSTNAME) "/uImage\0"		\
193 	"ramdisk_file=" __stringify(CONFIG_HOSTNAME) "/image.ext2\0"	\
194 	"flash_self=run ramargs addip addtty addmtd addmisc addmem;"	\
195 			"bootm ${kernel_addr_r}\0"			\
196 	"flash_nfs=run nfsargs addip addtty addmtd addmisc addmem;"	\
197 		"bootm ${kernel_addr}\0"				\
198 	"net_nfs=tftp ${kernel_addr_r} ${bootfile}; "			\
199 		"run nfsargs addip addtty addmtd addmisc addmem;"	\
200 		"bootm ${kernel_addr_r}\0"				\
201 	"net_rfsb=tftp ${kernel_addr_r} ${bootfile}; "			\
202 		"run rfsbargs addip addtty addmtd addmisc addmem; "	\
203 		"bootm ${kernel_addr_r}\0"				\
204 	"net_testrfs=tftp ${kernel_addr_r} ${bootfile}; "		\
205 		"run testrfsargs addip addtty addmtd addmisc addmem; "	\
206 		"bootm ${kernel_addr_r}\0"				\
207 	"net_self_load=tftp ${kernel_addr_r} ${bootfile};"		\
208 		"tftp ${ramdisk_addr_r} ${ramdisk_file};\0"		\
209 	"nand_nand=ubi part nand0,${as};ubifsmount ubi:rootfs;"		\
210 		"ubifsload ${kernel_addr_r} /boot/uImage;"		\
211 		"ubifsumount; run nandargs addip addtty "		\
212 		"addmtd addmisc addmem;clrlogo;"			\
213 		"bootm ${kernel_addr_r}\0"				\
214 	"nand_nandrw=ubi part nand0,${as};ubifsmount ubi:rootfs;"	\
215 		"ubifsload ${kernel_addr_r} /boot/uImage;"		\
216 		"ubifsumount; run nandrwargs addip addtty "		\
217 		"addmtd addmisc addmem;clrlogo;"			\
218 		"bootm ${kernel_addr_r}\0"				\
219 	"net_nandrw=tftp ${kernel_addr_r} ${bootfile}; run nandrwargs"	\
220 		" addip addtty addmtd addmisc addmem;"			\
221 		"clrlogo;bootm ${kernel_addr_r}\0"			\
222 	"u-boot=" __stringify(CONFIG_HOSTNAME) "/u-boot.bin\0"		\
223 	"load_magic=if sf probe 0;then sf "				\
224 		"read c0000000 0x10000 0x60000;fi\0"			\
225 	"load_nand=ubi part nand0,${as};ubifsmount ubi:rootfs;"		\
226 		"if ubifsload c0000014 /boot/u-boot.bin;"		\
227 		"then mw c0000008 ${filesize};else echo Error reading"	\
228 		" u-boot from nand!;fi\0"				\
229 	"load_net=if sf probe 0;then sf read c0000000 0x10000 "	\
230 		"0x60000;tftp c0000014 ${u-boot};"			\
231 		"mw c0000008 ${filesize};fi\0"				\
232 	"upd=if sf probe 0;then sf erase 10000 60000;"			\
233 		"sf write c0000000 10000 60000;fi\0"			\
234 	"ublupdate=if tftp C0700000 ${ublname};then sf probe 0; "	\
235 		"sf erase 0 10000;"					\
236 		"sf write 0xc0700000 0 ${filesize};fi\0"		\
237 	"ubootupd_net=if run load_net;then echo Updating u-boot;"	\
238 		"if run upd; then echo U-Boot updated;"		\
239 			"else echo Error updating u-boot !;"		\
240 			"echo Board without bootloader !!;"		\
241 		"fi;"							\
242 		"else echo U-Boot not downloaded..exiting;fi\0"	\
243 	"ubootupd_nand=echo run load_magic,run load_nand,run upd;\0"	\
244 	"bootcmd=run net_testrfs\0"
245 
246 #include <asm/arch/hardware.h>
247 
248 #endif /* __CONFIG_H */
249