xref: /openbmc/u-boot/include/configs/ea20.h (revision 8ee59472)
1 /* SPDX-License-Identifier: GPL-2.0+ */
2 /*
3  * Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/
4  *
5  * Based on davinci_dvevm.h. Original Copyrights follow:
6  *
7  * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
8  */
9 
10 #ifndef __CONFIG_H
11 #define __CONFIG_H
12 
13 /*
14  * Board
15  */
16 #define CONFIG_DRIVER_TI_EMAC
17 #define CONFIG_USE_SPIFLASH
18 #define	CONFIG_SYS_USE_NAND
19 #define CONFIG_DRIVER_TI_EMAC_USE_RMII
20 #define CONFIG_DRIVER_TI_EMAC_RMII_NO_NEGOTIATE
21 #define CONFIG_PREBOOT
22 
23 /*
24  * SoC Configuration
25  */
26 #define CONFIG_SYS_CLK_FREQ		clk_get(DAVINCI_ARM_CLKID)
27 #define CONFIG_SYS_OSCIN_FREQ		24000000
28 #define CONFIG_SYS_TIMERBASE		DAVINCI_TIMER0_BASE
29 #define CONFIG_SYS_HZ_CLOCK		clk_get(DAVINCI_AUXCLK_CLKID)
30 #define CONFIG_SKIP_LOWLEVEL_INIT
31 #define CONFIG_DA8XX_GPIO
32 
33 /*
34  * Memory Info
35  */
36 #define CONFIG_SYS_MALLOC_LEN	(0x10000 + 4*1024*1024) /* malloc() len */
37 #define PHYS_SDRAM_1		DAVINCI_DDR_EMIF_DATA_BASE /* DDR Start */
38 #define PHYS_SDRAM_1_SIZE	(64 << 20) /* SDRAM size 64MB */
39 #define CONFIG_MAX_RAM_BANK_SIZE (512 << 20) /* max size from SPRS586*/
40 
41 /* memtest start addr */
42 #define CONFIG_SYS_MEMTEST_START	(PHYS_SDRAM_1 + 0x2000000)
43 
44 /* memtest will be run on 16MB */
45 #define CONFIG_SYS_MEMTEST_END	(PHYS_SDRAM_1 + 0x2000000 + 16*1024*1024)
46 
47 #define CONFIG_NR_DRAM_BANKS	1 /* we have 1 bank of DRAM */
48 
49 /*
50  * Serial Driver info
51  */
52 #define CONFIG_SYS_NS16550_SERIAL
53 #define CONFIG_SYS_NS16550_REG_SIZE	-4	/* NS16550 register size */
54 #define CONFIG_SYS_NS16550_COM1	DAVINCI_UART0_BASE /* Base address of UART0 */
55 #define CONFIG_SYS_NS16550_CLK	clk_get(DAVINCI_UART2_CLKID)
56 
57 #define CONFIG_SYS_SPI_BASE		DAVINCI_SPI1_BASE
58 #define CONFIG_SYS_SPI_CLK		clk_get(DAVINCI_SPI1_CLKID)
59 #define CONFIG_SF_DEFAULT_SPEED		30000000
60 #define CONFIG_ENV_SPI_MAX_HZ	CONFIG_SF_DEFAULT_SPEED
61 
62 /*
63  * I2C Configuration
64  */
65 #define CONFIG_SYS_I2C
66 #define CONFIG_SYS_I2C_DAVINCI
67 #define CONFIG_SYS_DAVINCI_I2C_SPEED		100000
68 #define CONFIG_SYS_DAVINCI_I2C_SLAVE   10 /* Bogus, master-only in U-Boot */
69 
70 /*
71  * Network & Ethernet Configuration
72  */
73 #ifdef CONFIG_DRIVER_TI_EMAC
74 #define CONFIG_MII
75 #define CONFIG_BOOTP_DNS2
76 #define CONFIG_BOOTP_SEND_HOSTNAME
77 #define CONFIG_NET_RETRY_COUNT	10
78 #endif
79 
80 #ifdef CONFIG_USE_SPIFLASH
81 #define CONFIG_ENV_SIZE			(8 << 10)
82 #define CONFIG_ENV_OFFSET		0x80000
83 #define CONFIG_ENV_SECT_SIZE		(64 << 10)
84 #endif
85 
86 #if defined(CONFIG_VIDEO)
87 #define CONFIG_VIDEO_DA8XX
88 #define CONFIG_SPLASH_SCREEN_ALIGN
89 #define CONFIG_VIDEO_LOGO
90 #define CONFIG_VIDEO_BMP_RLE8
91 #define CONFIG_VIDEO_BMP_LOGO
92 #endif
93 
94 /*
95  * U-Boot general configuration
96  */
97 #define CONFIG_BOOTFILE		"uImage" /* Boot file name */
98 #define CONFIG_SYS_CBSIZE	1024 /* Console I/O Buffer Size	*/
99 #define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE /* Boot Args Buffer Size */
100 #define CONFIG_SYS_LOAD_ADDR	(PHYS_SDRAM_1 + 0x700000)
101 #define CONFIG_MX_CYCLIC
102 
103 /*
104  * Linux Information
105  */
106 #define LINUX_BOOT_PARAM_ADDR	(PHYS_SDRAM_1 + 0x100)
107 #define CONFIG_CMDLINE_TAG
108 #define CONFIG_SETUP_MEMORY_TAGS
109 
110 #ifdef CONFIG_CMD_BDI
111 #define CONFIG_CLOCKS
112 #endif
113 
114 #ifndef CONFIG_DRIVER_TI_EMAC
115 #endif
116 
117 /* NAND Setup */
118 #ifdef CONFIG_SYS_USE_NAND
119 #define CONFIG_MTD_DEVICE
120 #define CONFIG_MTD_PARTITIONS
121 
122 #define CONFIG_NAND_DAVINCI
123 #define	CONFIG_SYS_NAND_PAGE_2K
124 #define CONFIG_SYS_NAND_NO_SUBPAGE
125 #define CONFIG_SYS_NAND_CS		2
126 #define CONFIG_SYS_NAND_BASE		DAVINCI_ASYNC_EMIF_DATA_CE2_BASE
127 #undef CONFIG_SYS_NAND_HW_ECC
128 #define CONFIG_SYS_NAND_4BIT_HW_ECC_OOBFIRST
129 #define	CONFIG_SYS_NAND_USE_FLASH_BBT
130 #define CONFIG_SYS_MAX_NAND_DEVICE	1 /* Max number of NAND devices */
131 #endif
132 
133 /* SPI Flash */
134 #ifdef CONFIG_USE_SPIFLASH
135 #endif
136 
137 #if !defined(CONFIG_SYS_USE_NAND) && \
138 	!defined(CONFIG_USE_NOR) && \
139 	!defined(CONFIG_USE_SPIFLASH)
140 #define CONFIG_ENV_SIZE		(16 << 10)
141 #endif
142 
143 /* additions for new relocation code, must added to all boards */
144 #define CONFIG_SYS_SDRAM_BASE		0xc0000000
145 #define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_SDRAM_BASE + 0x1000 - \
146 					GENERATED_GBL_DATA_SIZE)
147 /*
148  * Default environment and default scripts
149  * to update uboot and load kernel
150  */
151 
152 #define CONFIG_HOSTNAME "ea20"
153 #define	CONFIG_EXTRA_ENV_SETTINGS				\
154 	"as=3\0"							\
155 	"netdev=eth0\0"						\
156 	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
157 		"nfsroot=${serverip}:${rootpath}\0"			\
158 	"rfsbargs=setenv bootargs root=/dev/nfs rw "			\
159 	"nfsroot=${serverip}:${rfsbpath}\0"				\
160 	"testrfsargs=setenv bootargs root=/dev/nfs rw "		\
161 	"nfsroot=${serverip}:${testrfspath}\0"				\
162 	"ramargs=setenv bootargs root=/dev/ram rw initrd="		\
163 	"0x${ramdisk_addr_r},4M\0"					\
164 	"mtdids=nand0=davinci_nand.0\0"				\
165 	"serverip=192.168.5.249\0"					\
166 	"ipaddr=192.168.5.248\0"					\
167 	"rootpath=/opt/eldk/arm\0"					\
168 	"splashpos=230,180\0"						\
169 	"testrfspath=/opt/eldk/test_arm\0"				\
170 	"nandargs=setenv bootargs rootfstype=ubifs ro chk_data_crc "	\
171 	"ubi.mtd=${as} root=ubi0:rootfs\0"				\
172 	"nandrwargs=setenv bootargs rootfstype=ubifs rw chk_data_crc "	\
173 	"ubi.mtd=${as} root=ubi0:rootfs\0"				\
174 	"addip_sta=setenv bootargs ${bootargs} "			\
175 		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
176 		":${hostname}:${netdev}:off panic=1\0"			\
177 	"addip_dyn=setenv bootargs ${bootargs} ip=dhcp\0"		\
178 	"addip=if test -n ${ipdyn};then run addip_dyn;"		\
179 		"else run addip_sta;fi\0"				\
180 	"addmtd=setenv bootargs ${bootargs} ${mtdparts}\0"		\
181 	"addtty=setenv bootargs ${bootargs}"				\
182 		" console=${consoledev},${baudrate}n8\0"		\
183 	"addmisc=setenv bootargs ${bootargs} ${misc}\0"		\
184 	"addmem=setenv bootargs ${bootargs} mem=${memory}\0"		\
185 	"consoledev=ttyS0\0"						\
186 	"loadaddr=c0000014\0"						\
187 	"memory=32M\0"							\
188 	"kernel_addr_r=c0700000\0"					\
189 	"hostname=" CONFIG_HOSTNAME "\0"			\
190 	"bootfile=" CONFIG_HOSTNAME "/uImage\0"		\
191 	"ramdisk_file=" CONFIG_HOSTNAME "/image.ext2\0"	\
192 	"flash_self=run ramargs addip addtty addmtd addmisc addmem;"	\
193 			"bootm ${kernel_addr_r}\0"			\
194 	"flash_nfs=run nfsargs addip addtty addmtd addmisc addmem;"	\
195 		"bootm ${kernel_addr}\0"				\
196 	"net_nfs=tftp ${kernel_addr_r} ${bootfile}; "			\
197 		"run nfsargs addip addtty addmtd addmisc addmem;"	\
198 		"bootm ${kernel_addr_r}\0"				\
199 	"net_rfsb=tftp ${kernel_addr_r} ${bootfile}; "			\
200 		"run rfsbargs addip addtty addmtd addmisc addmem; "	\
201 		"bootm ${kernel_addr_r}\0"				\
202 	"net_testrfs=tftp ${kernel_addr_r} ${bootfile}; "		\
203 		"run testrfsargs addip addtty addmtd addmisc addmem; "	\
204 		"bootm ${kernel_addr_r}\0"				\
205 	"net_self_load=tftp ${kernel_addr_r} ${bootfile};"		\
206 		"tftp ${ramdisk_addr_r} ${ramdisk_file};\0"		\
207 	"nand_nand=ubi part nand0,${as};ubifsmount ubi:rootfs;"		\
208 		"ubifsload ${kernel_addr_r} /boot/uImage;"		\
209 		"ubifsumount; run nandargs addip addtty "		\
210 		"addmtd addmisc addmem;clrlogo;"			\
211 		"bootm ${kernel_addr_r}\0"				\
212 	"nand_nandrw=ubi part nand0,${as};ubifsmount ubi:rootfs;"	\
213 		"ubifsload ${kernel_addr_r} /boot/uImage;"		\
214 		"ubifsumount; run nandrwargs addip addtty "		\
215 		"addmtd addmisc addmem;clrlogo;"			\
216 		"bootm ${kernel_addr_r}\0"				\
217 	"net_nandrw=tftp ${kernel_addr_r} ${bootfile}; run nandrwargs"	\
218 		" addip addtty addmtd addmisc addmem;"			\
219 		"clrlogo;bootm ${kernel_addr_r}\0"			\
220 	"u-boot=" CONFIG_HOSTNAME "/u-boot.bin\0"		\
221 	"load_magic=if sf probe 0;then sf "				\
222 		"read c0000000 0x10000 0x60000;fi\0"			\
223 	"load_nand=ubi part nand0,${as};ubifsmount ubi:rootfs;"		\
224 		"if ubifsload c0000014 /boot/u-boot.bin;"		\
225 		"then mw c0000008 ${filesize};else echo Error reading"	\
226 		" u-boot from nand!;fi\0"				\
227 	"load_net=if sf probe 0;then sf read c0000000 0x10000 "	\
228 		"0x60000;tftp c0000014 ${u-boot};"			\
229 		"mw c0000008 ${filesize};fi\0"				\
230 	"upd=if sf probe 0;then sf erase 10000 60000;"			\
231 		"sf write c0000000 10000 60000;fi\0"			\
232 	"ublupdate=if tftp C0700000 ${ublname};then sf probe 0; "	\
233 		"sf erase 0 10000;"					\
234 		"sf write 0xc0700000 0 ${filesize};fi\0"		\
235 	"ubootupd_net=if run load_net;then echo Updating u-boot;"	\
236 		"if run upd; then echo U-Boot updated;"		\
237 			"else echo Error updating u-boot !;"		\
238 			"echo Board without bootloader !!;"		\
239 		"fi;"							\
240 		"else echo U-Boot not downloaded..exiting;fi\0"	\
241 	"ubootupd_nand=echo run load_magic,run load_nand,run upd;\0"	\
242 	"bootcmd=run net_testrfs\0"
243 
244 #include <asm/arch/hardware.h>
245 
246 #endif /* __CONFIG_H */
247