1 /* 2 * (C) Copyright 2011 3 * Jason Cooper <u-boot@lakedaemon.net> 4 * 5 * Based on work by: 6 * Marvell Semiconductor <www.marvell.com> 7 * Written-by: Siddarth Gore <gores@marvell.com> 8 * 9 * SPDX-License-Identifier: GPL-2.0+ 10 */ 11 12 #ifndef _CONFIG_DREAMPLUG_H 13 #define _CONFIG_DREAMPLUG_H 14 15 /* 16 * FIXME: This belongs in mach-types.h. However, we only pull mach-types 17 * from Linus' kernel.org tree. This hasn't been updated primarily due to 18 * the recent arch/arm reshuffling. So, in the meantime, we'll place it 19 * here. 20 */ 21 #include <asm/mach-types.h> 22 #ifdef MACH_TYPE_DREAMPLUG 23 #error "MACH_TYPE_DREAMPLUG has been defined properly, please remove this." 24 #else 25 #define MACH_TYPE_DREAMPLUG 3550 26 #endif 27 28 /* 29 * High Level Configuration Options (easy to change) 30 */ 31 #define CONFIG_SHEEVA_88SV131 1 /* CPU Core subversion */ 32 #define CONFIG_MACH_TYPE MACH_TYPE_DREAMPLUG 33 34 /* 35 * Commands configuration 36 */ 37 38 /* 39 * mv-plug-common.h should be defined after CMD configs since it used them 40 * to enable certain macros 41 */ 42 #include "mv-plug-common.h" 43 44 /* 45 * Environment variables configurations 46 */ 47 #ifdef CONFIG_SPI_FLASH 48 #define CONFIG_ENV_IS_IN_SPI_FLASH 1 49 #define CONFIG_ENV_SECT_SIZE 0x10000 /* 64k */ 50 #else 51 #define CONFIG_ENV_IS_NOWHERE 1 /* if env in SDRAM */ 52 #endif 53 54 #ifdef CONFIG_CMD_SF 55 #define CONFIG_HARD_SPI 1 56 #define CONFIG_KIRKWOOD_SPI 1 57 #define CONFIG_ENV_SPI_BUS 0 58 #define CONFIG_ENV_SPI_CS 0 59 #define CONFIG_ENV_SPI_MAX_HZ 50000000 /* 50 MHz */ 60 #endif 61 62 /* 63 * max 4k env size is enough, but in case of nand 64 * it has to be rounded to sector size 65 */ 66 #define CONFIG_ENV_SIZE 0x1000 /* 4k */ 67 #define CONFIG_ENV_ADDR 0x100000 68 #define CONFIG_ENV_OFFSET 0x100000 /* env starts here */ 69 70 /* 71 * Default environment variables 72 */ 73 #define CONFIG_BOOTCOMMAND "setenv ethact egiga0; " \ 74 "${x_bootcmd_ethernet}; setenv ethact egiga1; " \ 75 "${x_bootcmd_ethernet}; ${x_bootcmd_usb}; ${x_bootcmd_kernel}; "\ 76 "setenv bootargs ${x_bootargs} ${x_bootargs_root}; " \ 77 "bootm 0x6400000;" 78 79 #define CONFIG_EXTRA_ENV_SETTINGS \ 80 "x_bootcmd_ethernet=ping 192.168.2.1\0" \ 81 "x_bootcmd_usb=usb start\0" \ 82 "x_bootcmd_kernel=fatload usb 0 0x6400000 uImage\0" \ 83 "x_bootargs=console=ttyS0,115200\0" \ 84 "x_bootargs_root=root=/dev/sda2 rootdelay=10\0" 85 86 /* 87 * Ethernet Driver configuration 88 */ 89 #ifdef CONFIG_CMD_NET 90 #define CONFIG_MVGBE_PORTS {1, 1} /* enable both ports */ 91 #define CONFIG_PHY_BASE_ADR 0 92 #endif /* CONFIG_CMD_NET */ 93 94 /* 95 * SATA Driver configuration 96 */ 97 #ifdef CONFIG_MVSATA_IDE 98 #define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET 99 #endif /*CONFIG_MVSATA_IDE*/ 100 101 #endif /* _CONFIG_DREAMPLUG_H */ 102