1 /* 2 * (C) Copyright 2011 3 * Jason Cooper <u-boot@lakedaemon.net> 4 * 5 * Based on work by: 6 * Marvell Semiconductor <www.marvell.com> 7 * Written-by: Siddarth Gore <gores@marvell.com> 8 * 9 * SPDX-License-Identifier: GPL-2.0+ 10 */ 11 12 #ifndef _CONFIG_DREAMPLUG_H 13 #define _CONFIG_DREAMPLUG_H 14 15 /* 16 * High Level Configuration Options (easy to change) 17 */ 18 #define CONFIG_SHEEVA_88SV131 1 /* CPU Core subversion */ 19 #define CONFIG_MACH_TYPE MACH_TYPE_DREAMPLUG 20 21 /* 22 * Commands configuration 23 */ 24 25 /* 26 * mv-plug-common.h should be defined after CMD configs since it used them 27 * to enable certain macros 28 */ 29 #include "mv-plug-common.h" 30 31 /* 32 * Environment variables configurations 33 */ 34 #ifdef CONFIG_SPI_FLASH 35 #define CONFIG_ENV_IS_IN_SPI_FLASH 1 36 #define CONFIG_ENV_SECT_SIZE 0x10000 /* 64k */ 37 #else 38 #define CONFIG_ENV_IS_NOWHERE 1 /* if env in SDRAM */ 39 #endif 40 41 #ifdef CONFIG_CMD_SF 42 #define CONFIG_HARD_SPI 1 43 #define CONFIG_KIRKWOOD_SPI 1 44 #define CONFIG_ENV_SPI_BUS 0 45 #define CONFIG_ENV_SPI_CS 0 46 #define CONFIG_ENV_SPI_MAX_HZ 50000000 /* 50 MHz */ 47 #endif 48 49 /* 50 * max 4k env size is enough, but in case of nand 51 * it has to be rounded to sector size 52 */ 53 #define CONFIG_ENV_SIZE 0x1000 /* 4k */ 54 #define CONFIG_ENV_ADDR 0x100000 55 #define CONFIG_ENV_OFFSET 0x100000 /* env starts here */ 56 57 /* 58 * Default environment variables 59 */ 60 #define CONFIG_BOOTCOMMAND "setenv ethact egiga0; " \ 61 "${x_bootcmd_ethernet}; setenv ethact egiga1; " \ 62 "${x_bootcmd_ethernet}; ${x_bootcmd_usb}; ${x_bootcmd_kernel}; "\ 63 "setenv bootargs ${x_bootargs} ${x_bootargs_root}; " \ 64 "bootm 0x6400000;" 65 66 #define CONFIG_EXTRA_ENV_SETTINGS \ 67 "x_bootcmd_ethernet=ping 192.168.2.1\0" \ 68 "x_bootcmd_usb=usb start\0" \ 69 "x_bootcmd_kernel=fatload usb 0 0x6400000 uImage\0" \ 70 "x_bootargs=console=ttyS0,115200\0" \ 71 "x_bootargs_root=root=/dev/sda2 rootdelay=10\0" 72 73 /* 74 * Ethernet Driver configuration 75 */ 76 #ifdef CONFIG_CMD_NET 77 #define CONFIG_MVGBE_PORTS {1, 1} /* enable both ports */ 78 #define CONFIG_PHY_BASE_ADR 0 79 #endif /* CONFIG_CMD_NET */ 80 81 /* 82 * SATA Driver configuration 83 */ 84 #ifdef CONFIG_MVSATA_IDE 85 #define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET 86 #endif /*CONFIG_MVSATA_IDE*/ 87 88 #endif /* _CONFIG_DREAMPLUG_H */ 89