1 /* SPDX-License-Identifier: GPL-2.0+ */ 2 /* 3 * Embest/Timll DevKit3250 board configuration file 4 * 5 * Copyright (C) 2011-2015 Vladimir Zapolskiy <vz@mleia.com> 6 */ 7 8 #ifndef __CONFIG_DEVKIT3250_H__ 9 #define __CONFIG_DEVKIT3250_H__ 10 11 /* SoC and board defines */ 12 #include <linux/sizes.h> 13 #include <asm/arch/cpu.h> 14 15 #define CONFIG_MACH_TYPE MACH_TYPE_DEVKIT3250 16 17 #define CONFIG_SYS_ICACHE_OFF 18 #define CONFIG_SYS_DCACHE_OFF 19 #if !defined(CONFIG_SPL_BUILD) 20 #define CONFIG_SKIP_LOWLEVEL_INIT 21 #endif 22 23 /* 24 * Memory configurations 25 */ 26 #define CONFIG_SYS_MALLOC_LEN SZ_1M 27 #define CONFIG_SYS_SDRAM_BASE EMC_DYCS0_BASE 28 #define CONFIG_SYS_SDRAM_SIZE SZ_64M 29 #define CONFIG_SYS_MEMTEST_START (CONFIG_SYS_SDRAM_BASE + SZ_32K) 30 #define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_TEXT_BASE - SZ_1M) 31 32 #define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + SZ_32K) 33 34 #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + SZ_4K \ 35 - GENERATED_GBL_DATA_SIZE) 36 37 /* 38 * Serial Driver 39 */ 40 #define CONFIG_SYS_LPC32XX_UART 5 /* UART5 */ 41 42 /* 43 * DMA 44 */ 45 #if !defined(CONFIG_SPL_BUILD) 46 #define CONFIG_DMA_LPC32XX 47 #endif 48 49 /* 50 * I2C 51 */ 52 #define CONFIG_SYS_I2C 53 #define CONFIG_SYS_I2C_LPC32XX 54 #define CONFIG_SYS_I2C_SPEED 100000 55 56 /* 57 * GPIO 58 */ 59 #define CONFIG_LPC32XX_GPIO 60 61 /* 62 * SSP/SPI 63 */ 64 #define CONFIG_LPC32XX_SSP_TIMEOUT 100000 65 66 /* 67 * Ethernet 68 */ 69 #define CONFIG_RMII 70 #define CONFIG_PHY_SMSC 71 #define CONFIG_LPC32XX_ETH 72 #define CONFIG_SYS_FAULT_ECHO_LINK_DOWN 73 74 /* 75 * NOR Flash 76 */ 77 #define CONFIG_SYS_MAX_FLASH_BANKS 1 78 #define CONFIG_SYS_MAX_FLASH_SECT 71 79 #define CONFIG_SYS_FLASH_BASE EMC_CS0_BASE 80 #define CONFIG_SYS_FLASH_SIZE SZ_4M 81 #define CONFIG_SYS_FLASH_CFI 82 83 /* 84 * NAND controller 85 */ 86 #define CONFIG_SYS_NAND_BASE SLC_NAND_BASE 87 #define CONFIG_SYS_MAX_NAND_DEVICE 1 88 #define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } 89 90 /* 91 * NAND chip timings 92 */ 93 #define CONFIG_LPC32XX_NAND_SLC_WDR_CLKS 14 94 #define CONFIG_LPC32XX_NAND_SLC_WWIDTH 66666666 95 #define CONFIG_LPC32XX_NAND_SLC_WHOLD 200000000 96 #define CONFIG_LPC32XX_NAND_SLC_WSETUP 50000000 97 #define CONFIG_LPC32XX_NAND_SLC_RDR_CLKS 14 98 #define CONFIG_LPC32XX_NAND_SLC_RWIDTH 66666666 99 #define CONFIG_LPC32XX_NAND_SLC_RHOLD 200000000 100 #define CONFIG_LPC32XX_NAND_SLC_RSETUP 50000000 101 102 #define CONFIG_SYS_NAND_BLOCK_SIZE 0x20000 103 #define CONFIG_SYS_NAND_PAGE_SIZE NAND_LARGE_BLOCK_PAGE_SIZE 104 #define CONFIG_SYS_NAND_USE_FLASH_BBT 105 106 /* 107 * USB 108 */ 109 #define CONFIG_USB_OHCI_LPC32XX 110 #define CONFIG_USB_ISP1301_I2C_ADDR 0x2d 111 112 /* 113 * U-Boot General Configurations 114 */ 115 #define CONFIG_SYS_CBSIZE 1024 116 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE 117 118 /* 119 * Pass open firmware flat tree 120 */ 121 122 /* 123 * Environment 124 */ 125 #define CONFIG_ENV_SIZE SZ_128K 126 #define CONFIG_ENV_OFFSET 0x000A0000 127 128 #define CONFIG_BOOTCOMMAND \ 129 "dhcp; " \ 130 "tftp ${loadaddr} ${serverip}:${tftpdir}/${bootfile}; " \ 131 "tftp ${dtbaddr} ${serverip}:${tftpdir}/devkit3250.dtb; " \ 132 "setenv nfsargs ip=dhcp root=/dev/nfs nfsroot=${serverip}:${nfsroot},tcp; " \ 133 "setenv bootargs ${bootargs} ${nfsargs} ${userargs}; " \ 134 "bootm ${loadaddr} - ${dtbaddr}" 135 136 #define CONFIG_EXTRA_ENV_SETTINGS \ 137 "autoload=no\0" \ 138 "ethaddr=00:01:90:00:C0:81\0" \ 139 "dtbaddr=0x81000000\0" \ 140 "nfsroot=/opt/projects/images/vladimir/oe/devkit3250/rootfs\0" \ 141 "tftpdir=vladimir/oe/devkit3250\0" \ 142 "userargs=oops=panic\0" 143 144 /* 145 * U-Boot Commands 146 */ 147 148 /* 149 * Boot Linux 150 */ 151 #define CONFIG_CMDLINE_TAG 152 #define CONFIG_SETUP_MEMORY_TAGS 153 154 #define CONFIG_BOOTFILE "uImage" 155 #define CONFIG_LOADADDR 0x80008000 156 157 /* 158 * SPL specific defines 159 */ 160 /* SPL will be executed at offset 0 */ 161 #define CONFIG_SPL_TEXT_BASE 0x00000000 162 163 /* SPL will use SRAM as stack */ 164 #define CONFIG_SPL_STACK 0x0000FFF8 165 166 /* Use the framework and generic lib */ 167 168 /* SPL will use serial */ 169 170 /* SPL loads an image from NAND */ 171 #define CONFIG_SPL_NAND_RAW_ONLY 172 #define CONFIG_SPL_NAND_DRIVERS 173 174 #define CONFIG_SPL_NAND_ECC 175 #define CONFIG_SPL_NAND_SOFTECC 176 177 #define CONFIG_SPL_MAX_SIZE 0x20000 178 #define CONFIG_SPL_PAD_TO CONFIG_SPL_MAX_SIZE 179 180 /* U-Boot will be 0x60000 bytes, loaded and run at CONFIG_SYS_TEXT_BASE */ 181 #define CONFIG_SYS_NAND_U_BOOT_OFFS 0x40000 182 #define CONFIG_SYS_NAND_U_BOOT_SIZE 0x60000 183 184 #define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE 185 #define CONFIG_SYS_NAND_U_BOOT_DST CONFIG_SYS_TEXT_BASE 186 187 /* See common/spl/spl.c spl_set_header_raw_uboot() */ 188 #define CONFIG_SYS_MONITOR_LEN CONFIG_SYS_NAND_U_BOOT_SIZE 189 190 /* 191 * Include SoC specific configuration 192 */ 193 #include <asm/arch/config.h> 194 195 #endif /* __CONFIG_DEVKIT3250_H__*/ 196