1 /* 2 * Copyright (C) 2014 Stefan Roese <sr@denx.de> 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 #ifndef _CONFIG_DB_88F6820_AMC_H 8 #define _CONFIG_DB_88F6820_AMC_H 9 10 /* 11 * High Level Configuration Options (easy to change) 12 */ 13 14 #define CONFIG_DISPLAY_BOARDINFO_LATE 15 16 /* 17 * TEXT_BASE needs to be below 16MiB, since this area is scrubbed 18 * for DDR ECC byte filling in the SPL before loading the main 19 * U-Boot into it. 20 */ 21 #define CONFIG_SYS_TEXT_BASE 0x00800000 22 #define CONFIG_SYS_TCLK 200000000 /* 200MHz */ 23 24 /* 25 * Commands configuration 26 */ 27 #define CONFIG_CMD_ENV 28 #define CONFIG_CMD_PCI 29 30 /* SPI NOR flash default params, used by sf commands */ 31 #define CONFIG_SF_DEFAULT_BUS 1 32 #define CONFIG_SF_DEFAULT_SPEED 1000000 33 #define CONFIG_SF_DEFAULT_MODE SPI_MODE_3 34 35 /* Partition support */ 36 37 /* Additional FS support/configuration */ 38 #define CONFIG_SUPPORT_VFAT 39 40 /* USB/EHCI configuration */ 41 #define CONFIG_EHCI_IS_TDI 42 43 /* Environment in SPI NOR flash */ 44 #define CONFIG_ENV_IS_IN_SPI_FLASH 45 #define CONFIG_ENV_SPI_BUS 1 46 #define CONFIG_ENV_OFFSET (1 << 20) /* 1MiB in */ 47 #define CONFIG_ENV_SIZE (64 << 10) /* 64KiB */ 48 #define CONFIG_ENV_SECT_SIZE (256 << 10) /* 256KiB sectors */ 49 50 #define CONFIG_PHY_MARVELL /* there is a marvell phy */ 51 #define PHY_ANEG_TIMEOUT 8000 /* PHY needs a longer aneg time */ 52 53 /* PCIe support */ 54 #ifndef CONFIG_SPL_BUILD 55 #define CONFIG_PCI_MVEBU 56 #define CONFIG_PCI_SCAN_SHOW 57 #endif 58 59 /* NAND */ 60 #define CONFIG_SYS_NAND_USE_FLASH_BBT 61 #define CONFIG_SYS_NAND_ONFI_DETECTION 62 63 #define CONFIG_SYS_ALT_MEMTEST 64 65 /* Keep device tree and initrd in lower memory so the kernel can access them */ 66 #define CONFIG_EXTRA_ENV_SETTINGS \ 67 "fdt_high=0x10000000\0" \ 68 "initrd_high=0x10000000\0" 69 70 /* SPL */ 71 /* 72 * Select the boot device here 73 * 74 * Currently supported are: 75 * SPL_BOOT_SPI_NOR_FLASH - Booting via SPI NOR flash 76 * 77 * MMC is not populated on this board. 78 * NAND support may be added in the future. 79 */ 80 #define SPL_BOOT_SPI_NOR_FLASH 1 81 #define CONFIG_SPL_BOOT_DEVICE SPL_BOOT_SPI_NOR_FLASH 82 83 /* Defines for SPL */ 84 #define CONFIG_SPL_FRAMEWORK 85 #define CONFIG_SPL_SIZE (140 << 10) 86 #define CONFIG_SPL_TEXT_BASE 0x40000030 87 #define CONFIG_SPL_MAX_SIZE (CONFIG_SPL_SIZE - 0x0030) 88 89 #define CONFIG_SPL_BSS_START_ADDR (0x40000000 + CONFIG_SPL_SIZE) 90 #define CONFIG_SPL_BSS_MAX_SIZE (16 << 10) 91 92 #ifdef CONFIG_SPL_BUILD 93 #define CONFIG_SYS_MALLOC_SIMPLE 94 #endif 95 96 #define CONFIG_SPL_STACK (0x40000000 + ((192 - 16) << 10)) 97 #define CONFIG_SPL_BOOTROM_SAVE (CONFIG_SPL_STACK + 4) 98 99 #if CONFIG_SPL_BOOT_DEVICE == SPL_BOOT_SPI_NOR_FLASH 100 /* SPL related SPI defines */ 101 #define CONFIG_SPL_SPI_LOAD 102 #define CONFIG_SYS_SPI_U_BOOT_OFFS 0x24000 103 #define CONFIG_SYS_U_BOOT_OFFS CONFIG_SYS_SPI_U_BOOT_OFFS 104 #endif 105 106 /* 107 * mv-common.h should be defined after CMD configs since it used them 108 * to enable certain macros 109 */ 110 #include "mv-common.h" 111 #undef CONFIG_SYS_MAXARGS 112 #define CONFIG_SYS_MAXARGS 96 113 114 #endif /* _CONFIG_DB_88F6820_AMC_H */ 115