1 /* 2 * Copyright (C) 2014 Stefan Roese <sr@denx.de> 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 #ifndef _CONFIG_DB_88F6820_AMC_H 8 #define _CONFIG_DB_88F6820_AMC_H 9 10 /* 11 * High Level Configuration Options (easy to change) 12 */ 13 14 #define CONFIG_DISPLAY_BOARDINFO_LATE 15 16 /* 17 * TEXT_BASE needs to be below 16MiB, since this area is scrubbed 18 * for DDR ECC byte filling in the SPL before loading the main 19 * U-Boot into it. 20 */ 21 #define CONFIG_SYS_TCLK 200000000 /* 200MHz */ 22 23 /* 24 * Commands configuration 25 */ 26 27 /* SPI NOR flash default params, used by sf commands */ 28 #define CONFIG_SF_DEFAULT_BUS 1 29 #define CONFIG_SF_DEFAULT_SPEED 1000000 30 #define CONFIG_SF_DEFAULT_MODE SPI_MODE_3 31 32 /* USB/EHCI configuration */ 33 #define CONFIG_EHCI_IS_TDI 34 35 /* Environment in SPI NOR flash */ 36 #define CONFIG_ENV_SPI_BUS 1 37 #define CONFIG_ENV_OFFSET (1 << 20) /* 1MiB in */ 38 #define CONFIG_ENV_SIZE (64 << 10) /* 64KiB */ 39 #define CONFIG_ENV_SECT_SIZE (256 << 10) /* 256KiB sectors */ 40 41 #define CONFIG_PHY_MARVELL /* there is a marvell phy */ 42 #define PHY_ANEG_TIMEOUT 8000 /* PHY needs a longer aneg time */ 43 44 /* PCIe support */ 45 #ifndef CONFIG_SPL_BUILD 46 #define CONFIG_PCI_MVEBU 47 #define CONFIG_PCI_SCAN_SHOW 48 #endif 49 50 /* NAND */ 51 #define CONFIG_SYS_NAND_USE_FLASH_BBT 52 #define CONFIG_SYS_NAND_ONFI_DETECTION 53 54 #define CONFIG_SYS_ALT_MEMTEST 55 56 /* Keep device tree and initrd in lower memory so the kernel can access them */ 57 #define CONFIG_EXTRA_ENV_SETTINGS \ 58 "fdt_high=0x10000000\0" \ 59 "initrd_high=0x10000000\0" 60 61 /* SPL */ 62 /* 63 * Select the boot device here 64 * 65 * Currently supported are: 66 * SPL_BOOT_SPI_NOR_FLASH - Booting via SPI NOR flash 67 * 68 * MMC is not populated on this board. 69 * NAND support may be added in the future. 70 */ 71 #define SPL_BOOT_SPI_NOR_FLASH 1 72 #define CONFIG_SPL_BOOT_DEVICE SPL_BOOT_SPI_NOR_FLASH 73 74 /* Defines for SPL */ 75 #define CONFIG_SPL_SIZE (140 << 10) 76 #define CONFIG_SPL_TEXT_BASE 0x40000030 77 #define CONFIG_SPL_MAX_SIZE (CONFIG_SPL_SIZE - 0x0030) 78 79 #define CONFIG_SPL_BSS_START_ADDR (0x40000000 + CONFIG_SPL_SIZE) 80 #define CONFIG_SPL_BSS_MAX_SIZE (16 << 10) 81 82 #ifdef CONFIG_SPL_BUILD 83 #define CONFIG_SYS_MALLOC_SIMPLE 84 #endif 85 86 #define CONFIG_SPL_STACK (0x40000000 + ((192 - 16) << 10)) 87 #define CONFIG_SPL_BOOTROM_SAVE (CONFIG_SPL_STACK + 4) 88 89 #if CONFIG_SPL_BOOT_DEVICE == SPL_BOOT_SPI_NOR_FLASH 90 /* SPL related SPI defines */ 91 #define CONFIG_SPL_SPI_LOAD 92 #define CONFIG_SYS_SPI_U_BOOT_OFFS 0x24000 93 #define CONFIG_SYS_U_BOOT_OFFS CONFIG_SYS_SPI_U_BOOT_OFFS 94 #endif 95 96 /* 97 * mv-common.h should be defined after CMD configs since it used them 98 * to enable certain macros 99 */ 100 #include "mv-common.h" 101 #undef CONFIG_SYS_MAXARGS 102 #define CONFIG_SYS_MAXARGS 96 103 104 #endif /* _CONFIG_DB_88F6820_AMC_H */ 105