1 /* 2 * Copyright (C) 2014 Stefan Roese <sr@denx.de> 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 #ifndef _CONFIG_DB_88F6820_AMC_H 8 #define _CONFIG_DB_88F6820_AMC_H 9 10 /* 11 * High Level Configuration Options (easy to change) 12 */ 13 14 #define CONFIG_DISPLAY_BOARDINFO_LATE 15 16 /* 17 * TEXT_BASE needs to be below 16MiB, since this area is scrubbed 18 * for DDR ECC byte filling in the SPL before loading the main 19 * U-Boot into it. 20 */ 21 #define CONFIG_SYS_TEXT_BASE 0x00800000 22 #define CONFIG_SYS_TCLK 200000000 /* 200MHz */ 23 24 /* 25 * Commands configuration 26 */ 27 #define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */ 28 #define CONFIG_CMD_ENV 29 #define CONFIG_CMD_PCI 30 31 /* I2C */ 32 #define CONFIG_SYS_I2C 33 #define CONFIG_SYS_I2C_MVTWSI 34 #define CONFIG_I2C_MVTWSI_BASE0 MVEBU_TWSI_BASE 35 #define CONFIG_SYS_I2C_SLAVE 0x0 36 #define CONFIG_SYS_I2C_SPEED 100000 37 38 /* SPI NOR flash default params, used by sf commands */ 39 #define CONFIG_SF_DEFAULT_BUS 1 40 #define CONFIG_SF_DEFAULT_SPEED 1000000 41 #define CONFIG_SF_DEFAULT_MODE SPI_MODE_3 42 43 /* Partition support */ 44 #define CONFIG_DOS_PARTITION 45 #define CONFIG_EFI_PARTITION 46 47 /* Additional FS support/configuration */ 48 #define CONFIG_SUPPORT_VFAT 49 50 /* USB/EHCI configuration */ 51 #define CONFIG_EHCI_IS_TDI 52 53 /* Environment in SPI NOR flash */ 54 #define CONFIG_ENV_IS_IN_SPI_FLASH 55 #define CONFIG_ENV_SPI_BUS 1 56 #define CONFIG_ENV_OFFSET (1 << 20) /* 1MiB in */ 57 #define CONFIG_ENV_SIZE (64 << 10) /* 64KiB */ 58 #define CONFIG_ENV_SECT_SIZE (256 << 10) /* 256KiB sectors */ 59 60 #define CONFIG_PHY_MARVELL /* there is a marvell phy */ 61 #define PHY_ANEG_TIMEOUT 8000 /* PHY needs a longer aneg time */ 62 63 /* PCIe support */ 64 #ifndef CONFIG_SPL_BUILD 65 #define CONFIG_PCI 66 #define CONFIG_PCI_MVEBU 67 #define CONFIG_PCI_PNP 68 #define CONFIG_PCI_SCAN_SHOW 69 #endif 70 71 /* NAND */ 72 #define CONFIG_SYS_NAND_USE_FLASH_BBT 73 #define CONFIG_SYS_NAND_ONFI_DETECTION 74 75 #define CONFIG_SYS_ALT_MEMTEST 76 77 /* Keep device tree and initrd in lower memory so the kernel can access them */ 78 #define CONFIG_EXTRA_ENV_SETTINGS \ 79 "fdt_high=0x10000000\0" \ 80 "initrd_high=0x10000000\0" 81 82 /* SPL */ 83 /* 84 * Select the boot device here 85 * 86 * Currently supported are: 87 * SPL_BOOT_SPI_NOR_FLASH - Booting via SPI NOR flash 88 * 89 * MMC is not populated on this board. 90 * NAND support may be added in the future. 91 */ 92 #define SPL_BOOT_SPI_NOR_FLASH 1 93 #define CONFIG_SPL_BOOT_DEVICE SPL_BOOT_SPI_NOR_FLASH 94 95 /* Defines for SPL */ 96 #define CONFIG_SPL_FRAMEWORK 97 #define CONFIG_SPL_SIZE (140 << 10) 98 #define CONFIG_SPL_TEXT_BASE 0x40000030 99 #define CONFIG_SPL_MAX_SIZE (CONFIG_SPL_SIZE - 0x0030) 100 101 #define CONFIG_SPL_BSS_START_ADDR (0x40000000 + CONFIG_SPL_SIZE) 102 #define CONFIG_SPL_BSS_MAX_SIZE (16 << 10) 103 104 #ifdef CONFIG_SPL_BUILD 105 #define CONFIG_SYS_MALLOC_SIMPLE 106 #endif 107 108 #define CONFIG_SPL_STACK (0x40000000 + ((192 - 16) << 10)) 109 #define CONFIG_SPL_BOOTROM_SAVE (CONFIG_SPL_STACK + 4) 110 111 #if CONFIG_SPL_BOOT_DEVICE == SPL_BOOT_SPI_NOR_FLASH 112 /* SPL related SPI defines */ 113 #define CONFIG_SPL_SPI_LOAD 114 #define CONFIG_SYS_SPI_U_BOOT_OFFS 0x24000 115 #define CONFIG_SYS_U_BOOT_OFFS CONFIG_SYS_SPI_U_BOOT_OFFS 116 #endif 117 118 /* 119 * mv-common.h should be defined after CMD configs since it used them 120 * to enable certain macros 121 */ 122 #include "mv-common.h" 123 #undef CONFIG_SYS_MAXARGS 124 #define CONFIG_SYS_MAXARGS 96 125 126 #endif /* _CONFIG_DB_88F6820_AMC_H */ 127