1 /* 2 * Copyright (C) 2014 Stefan Roese <sr@denx.de> 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 #ifndef _CONFIG_DB_88F6820_AMC_H 8 #define _CONFIG_DB_88F6820_AMC_H 9 10 /* 11 * High Level Configuration Options (easy to change) 12 */ 13 14 #define CONFIG_DISPLAY_BOARDINFO_LATE 15 16 /* 17 * TEXT_BASE needs to be below 16MiB, since this area is scrubbed 18 * for DDR ECC byte filling in the SPL before loading the main 19 * U-Boot into it. 20 */ 21 #define CONFIG_SYS_TEXT_BASE 0x00800000 22 #define CONFIG_SYS_TCLK 200000000 /* 200MHz */ 23 24 /* 25 * Commands configuration 26 */ 27 28 /* SPI NOR flash default params, used by sf commands */ 29 #define CONFIG_SF_DEFAULT_BUS 1 30 #define CONFIG_SF_DEFAULT_SPEED 1000000 31 #define CONFIG_SF_DEFAULT_MODE SPI_MODE_3 32 33 /* Partition support */ 34 35 /* Additional FS support/configuration */ 36 #define CONFIG_SUPPORT_VFAT 37 38 /* USB/EHCI configuration */ 39 #define CONFIG_EHCI_IS_TDI 40 41 /* Environment in SPI NOR flash */ 42 #define CONFIG_ENV_SPI_BUS 1 43 #define CONFIG_ENV_OFFSET (1 << 20) /* 1MiB in */ 44 #define CONFIG_ENV_SIZE (64 << 10) /* 64KiB */ 45 #define CONFIG_ENV_SECT_SIZE (256 << 10) /* 256KiB sectors */ 46 47 #define CONFIG_PHY_MARVELL /* there is a marvell phy */ 48 #define PHY_ANEG_TIMEOUT 8000 /* PHY needs a longer aneg time */ 49 50 /* PCIe support */ 51 #ifndef CONFIG_SPL_BUILD 52 #define CONFIG_PCI_MVEBU 53 #define CONFIG_PCI_SCAN_SHOW 54 #endif 55 56 /* NAND */ 57 #define CONFIG_SYS_NAND_USE_FLASH_BBT 58 #define CONFIG_SYS_NAND_ONFI_DETECTION 59 60 #define CONFIG_SYS_ALT_MEMTEST 61 62 /* Keep device tree and initrd in lower memory so the kernel can access them */ 63 #define CONFIG_EXTRA_ENV_SETTINGS \ 64 "fdt_high=0x10000000\0" \ 65 "initrd_high=0x10000000\0" 66 67 /* SPL */ 68 /* 69 * Select the boot device here 70 * 71 * Currently supported are: 72 * SPL_BOOT_SPI_NOR_FLASH - Booting via SPI NOR flash 73 * 74 * MMC is not populated on this board. 75 * NAND support may be added in the future. 76 */ 77 #define SPL_BOOT_SPI_NOR_FLASH 1 78 #define CONFIG_SPL_BOOT_DEVICE SPL_BOOT_SPI_NOR_FLASH 79 80 /* Defines for SPL */ 81 #define CONFIG_SPL_FRAMEWORK 82 #define CONFIG_SPL_SIZE (140 << 10) 83 #define CONFIG_SPL_TEXT_BASE 0x40000030 84 #define CONFIG_SPL_MAX_SIZE (CONFIG_SPL_SIZE - 0x0030) 85 86 #define CONFIG_SPL_BSS_START_ADDR (0x40000000 + CONFIG_SPL_SIZE) 87 #define CONFIG_SPL_BSS_MAX_SIZE (16 << 10) 88 89 #ifdef CONFIG_SPL_BUILD 90 #define CONFIG_SYS_MALLOC_SIMPLE 91 #endif 92 93 #define CONFIG_SPL_STACK (0x40000000 + ((192 - 16) << 10)) 94 #define CONFIG_SPL_BOOTROM_SAVE (CONFIG_SPL_STACK + 4) 95 96 #if CONFIG_SPL_BOOT_DEVICE == SPL_BOOT_SPI_NOR_FLASH 97 /* SPL related SPI defines */ 98 #define CONFIG_SPL_SPI_LOAD 99 #define CONFIG_SYS_SPI_U_BOOT_OFFS 0x24000 100 #define CONFIG_SYS_U_BOOT_OFFS CONFIG_SYS_SPI_U_BOOT_OFFS 101 #endif 102 103 /* 104 * mv-common.h should be defined after CMD configs since it used them 105 * to enable certain macros 106 */ 107 #include "mv-common.h" 108 #undef CONFIG_SYS_MAXARGS 109 #define CONFIG_SYS_MAXARGS 96 110 111 #endif /* _CONFIG_DB_88F6820_AMC_H */ 112