xref: /openbmc/u-boot/include/configs/da850evm.h (revision c2012cb4)
1 /*
2  * Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/
3  *
4  * Based on davinci_dvevm.h. Original Copyrights follow:
5  *
6  * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
7  *
8  * SPDX-License-Identifier:	GPL-2.0+
9  */
10 
11 #ifndef __CONFIG_H
12 #define __CONFIG_H
13 
14 /*
15  * Board
16  */
17 #define CONFIG_DRIVER_TI_EMAC
18 /* check if direct NOR boot config is used */
19 #ifndef CONFIG_DIRECT_NOR_BOOT
20 #define CONFIG_USE_SPIFLASH
21 #endif
22 
23 /*
24  * SoC Configuration
25  */
26 #define CONFIG_MACH_DAVINCI_DA850_EVM
27 #define CONFIG_SOC_DA8XX		/* TI DA8xx SoC */
28 #define CONFIG_SOC_DA850		/* TI DA850 SoC */
29 #define CONFIG_SYS_EXCEPTION_VECTORS_HIGH
30 #define CONFIG_SYS_CLK_FREQ		clk_get(DAVINCI_ARM_CLKID)
31 #define CONFIG_SYS_OSCIN_FREQ		24000000
32 #define CONFIG_SYS_TIMERBASE		DAVINCI_TIMER0_BASE
33 #define CONFIG_SYS_HZ_CLOCK		clk_get(DAVINCI_AUXCLK_CLKID)
34 
35 #ifdef CONFIG_DIRECT_NOR_BOOT
36 #define CONFIG_ARCH_CPU_INIT
37 #define CONFIG_DA8XX_GPIO
38 #define CONFIG_SYS_TEXT_BASE		0x60000000
39 #define CONFIG_SYS_DV_NOR_BOOT_CFG	(0x11)
40 #define CONFIG_DA850_LOWLEVEL
41 #else
42 #define CONFIG_SYS_TEXT_BASE		0xc1080000
43 #endif
44 
45 /*
46  * Memory Info
47  */
48 #define CONFIG_SYS_MALLOC_LEN	(0x10000 + 1*1024*1024) /* malloc() len */
49 #define PHYS_SDRAM_1		DAVINCI_DDR_EMIF_DATA_BASE /* DDR Start */
50 #define PHYS_SDRAM_1_SIZE	(64 << 20) /* SDRAM size 64MB */
51 #define CONFIG_MAX_RAM_BANK_SIZE (512 << 20) /* max size from SPRS586*/
52 
53 /* memtest start addr */
54 #define CONFIG_SYS_MEMTEST_START	(PHYS_SDRAM_1 + 0x2000000)
55 
56 /* memtest will be run on 16MB */
57 #define CONFIG_SYS_MEMTEST_END 	(PHYS_SDRAM_1 + 0x2000000 + 16*1024*1024)
58 
59 #define CONFIG_NR_DRAM_BANKS	1 /* we have 1 bank of DRAM */
60 
61 #define CONFIG_SYS_DA850_SYSCFG_SUSPSRC (	\
62 	DAVINCI_SYSCFG_SUSPSRC_TIMER0 |		\
63 	DAVINCI_SYSCFG_SUSPSRC_SPI1 |		\
64 	DAVINCI_SYSCFG_SUSPSRC_UART2 |		\
65 	DAVINCI_SYSCFG_SUSPSRC_EMAC |		\
66 	DAVINCI_SYSCFG_SUSPSRC_I2C)
67 
68 /*
69  * PLL configuration
70  */
71 #define CONFIG_SYS_DV_CLKMODE          0
72 #define CONFIG_SYS_DA850_PLL0_POSTDIV  1
73 #define CONFIG_SYS_DA850_PLL0_PLLDIV1  0x8000
74 #define CONFIG_SYS_DA850_PLL0_PLLDIV2  0x8001
75 #define CONFIG_SYS_DA850_PLL0_PLLDIV3  0x8002
76 #define CONFIG_SYS_DA850_PLL0_PLLDIV4  0x8003
77 #define CONFIG_SYS_DA850_PLL0_PLLDIV5  0x8002
78 #define CONFIG_SYS_DA850_PLL0_PLLDIV6  CONFIG_SYS_DA850_PLL0_PLLDIV1
79 #define CONFIG_SYS_DA850_PLL0_PLLDIV7  0x8005
80 
81 #define CONFIG_SYS_DA850_PLL1_POSTDIV  1
82 #define CONFIG_SYS_DA850_PLL1_PLLDIV1  0x8000
83 #define CONFIG_SYS_DA850_PLL1_PLLDIV2  0x8001
84 #define CONFIG_SYS_DA850_PLL1_PLLDIV3  0x8002
85 
86 #define CONFIG_SYS_DA850_PLL0_PLLM     24
87 #define CONFIG_SYS_DA850_PLL1_PLLM     21
88 
89 /*
90  * DDR2 memory configuration
91  */
92 #define CONFIG_SYS_DA850_DDR2_DDRPHYCR (DV_DDR_PHY_PWRDNEN | \
93 					DV_DDR_PHY_EXT_STRBEN | \
94 					(0x4 << DV_DDR_PHY_RD_LATENCY_SHIFT))
95 
96 #define CONFIG_SYS_DA850_DDR2_SDBCR (		\
97 	(1 << DV_DDR_SDCR_MSDRAMEN_SHIFT) |	\
98 	(1 << DV_DDR_SDCR_DDREN_SHIFT) |	\
99 	(1 << DV_DDR_SDCR_SDRAMEN_SHIFT) |	\
100 	(1 << DV_DDR_SDCR_BUS_WIDTH_SHIFT) |	\
101 	(0x3 << DV_DDR_SDCR_CL_SHIFT) |		\
102 	(0x2 << DV_DDR_SDCR_IBANK_SHIFT) |	\
103 	(0x2 << DV_DDR_SDCR_PAGESIZE_SHIFT))
104 
105 /* SDBCR2 is only used if IBANK_POS bit in SDBCR is set */
106 #define CONFIG_SYS_DA850_DDR2_SDBCR2 0
107 
108 #define CONFIG_SYS_DA850_DDR2_SDTIMR (		\
109 	(14 << DV_DDR_SDTMR1_RFC_SHIFT) |	\
110 	(2 << DV_DDR_SDTMR1_RP_SHIFT) |		\
111 	(2 << DV_DDR_SDTMR1_RCD_SHIFT) |	\
112 	(1 << DV_DDR_SDTMR1_WR_SHIFT) |		\
113 	(5 << DV_DDR_SDTMR1_RAS_SHIFT) |	\
114 	(8 << DV_DDR_SDTMR1_RC_SHIFT) |		\
115 	(1 << DV_DDR_SDTMR1_RRD_SHIFT) |	\
116 	(0 << DV_DDR_SDTMR1_WTR_SHIFT))
117 
118 #define CONFIG_SYS_DA850_DDR2_SDTIMR2 (		\
119 	(7 << DV_DDR_SDTMR2_RASMAX_SHIFT) |	\
120 	(0 << DV_DDR_SDTMR2_XP_SHIFT) |		\
121 	(0 << DV_DDR_SDTMR2_ODT_SHIFT) |	\
122 	(17 << DV_DDR_SDTMR2_XSNR_SHIFT) |	\
123 	(199 << DV_DDR_SDTMR2_XSRD_SHIFT) |	\
124 	(0 << DV_DDR_SDTMR2_RTP_SHIFT) |	\
125 	(0 << DV_DDR_SDTMR2_CKE_SHIFT))
126 
127 #define CONFIG_SYS_DA850_DDR2_SDRCR    0x00000494
128 #define CONFIG_SYS_DA850_DDR2_PBBPR    0x30
129 
130 /*
131  * Serial Driver info
132  */
133 #define CONFIG_SYS_NS16550_SERIAL
134 #define CONFIG_SYS_NS16550_REG_SIZE	-4	/* NS16550 register size */
135 #define CONFIG_SYS_NS16550_COM1	DAVINCI_UART2_BASE /* Base address of UART2 */
136 #define CONFIG_SYS_NS16550_CLK	clk_get(DAVINCI_UART2_CLKID)
137 #define CONFIG_CONS_INDEX	1		/* use UART0 for console */
138 
139 #define CONFIG_SPI
140 #define CONFIG_DAVINCI_SPI
141 #define CONFIG_SYS_SPI_BASE		DAVINCI_SPI1_BASE
142 #define CONFIG_SYS_SPI_CLK		clk_get(DAVINCI_SPI1_CLKID)
143 #define CONFIG_SF_DEFAULT_SPEED		30000000
144 #define CONFIG_ENV_SPI_MAX_HZ	CONFIG_SF_DEFAULT_SPEED
145 
146 #ifdef CONFIG_USE_SPIFLASH
147 #define CONFIG_SPL_SPI_LOAD
148 #define CONFIG_SYS_SPI_U_BOOT_OFFS	0x8000
149 #define CONFIG_SYS_SPI_U_BOOT_SIZE	0x40000
150 #endif
151 
152 /*
153  * I2C Configuration
154  */
155 #define CONFIG_SYS_I2C
156 #define CONFIG_SYS_I2C_DAVINCI
157 #define CONFIG_SYS_DAVINCI_I2C_SPEED		25000
158 #define CONFIG_SYS_DAVINCI_I2C_SLAVE   10 /* Bogus, master-only in U-Boot */
159 #define CONFIG_SYS_I2C_EXPANDER_ADDR   0x20
160 
161 /*
162  * Flash & Environment
163  */
164 #ifdef CONFIG_USE_NAND
165 #define CONFIG_NAND_DAVINCI
166 #define CONFIG_ENV_OFFSET		0x0 /* Block 0--not used by bootcode */
167 #define CONFIG_ENV_SIZE			(128 << 10)
168 #define	CONFIG_SYS_NAND_USE_FLASH_BBT
169 #define CONFIG_SYS_NAND_4BIT_HW_ECC_OOBFIRST
170 #define	CONFIG_SYS_NAND_PAGE_2K
171 #define CONFIG_SYS_NAND_CS		3
172 #define CONFIG_SYS_NAND_BASE		DAVINCI_ASYNC_EMIF_DATA_CE3_BASE
173 #define CONFIG_SYS_NAND_MASK_CLE		0x10
174 #define CONFIG_SYS_NAND_MASK_ALE		0x8
175 #undef CONFIG_SYS_NAND_HW_ECC
176 #define CONFIG_SYS_MAX_NAND_DEVICE	1 /* Max number of NAND devices */
177 #define CONFIG_SYS_NAND_HW_ECC_OOBFIRST
178 #define CONFIG_SYS_NAND_5_ADDR_CYCLE
179 #define CONFIG_SYS_NAND_PAGE_SIZE	(2 << 10)
180 #define CONFIG_SYS_NAND_BLOCK_SIZE	(128 << 10)
181 #define CONFIG_SYS_NAND_U_BOOT_OFFS	0x28000
182 #define CONFIG_SYS_NAND_U_BOOT_SIZE	0x60000
183 #define CONFIG_SYS_NAND_U_BOOT_DST	0xc1080000
184 #define CONFIG_SYS_NAND_U_BOOT_START	CONFIG_SYS_NAND_U_BOOT_DST
185 #define CONFIG_SYS_NAND_U_BOOT_RELOC_SP	(CONFIG_SYS_NAND_U_BOOT_DST - \
186 					CONFIG_SYS_NAND_U_BOOT_SIZE - \
187 					CONFIG_SYS_MALLOC_LEN -       \
188 					GENERATED_GBL_DATA_SIZE)
189 #define CONFIG_SYS_NAND_ECCPOS		{				\
190 				24, 25, 26, 27, 28, \
191 				29, 30, 31, 32, 33, 34, 35, 36, 37, 38, \
192 				39, 40, 41, 42, 43, 44, 45, 46, 47, 48, \
193 				49, 50, 51, 52, 53, 54, 55, 56, 57, 58, \
194 				59, 60, 61, 62, 63 }
195 #define CONFIG_SYS_NAND_PAGE_COUNT	64
196 #define CONFIG_SYS_NAND_BAD_BLOCK_POS	0
197 #define CONFIG_SYS_NAND_ECCSIZE		512
198 #define CONFIG_SYS_NAND_ECCBYTES	10
199 #define CONFIG_SYS_NAND_OOBSIZE		64
200 #define CONFIG_SPL_NAND_BASE
201 #define CONFIG_SPL_NAND_DRIVERS
202 #define CONFIG_SPL_NAND_ECC
203 #define CONFIG_SPL_NAND_SIMPLE
204 #define CONFIG_SPL_NAND_LOAD
205 #endif
206 
207 /*
208  * Network & Ethernet Configuration
209  */
210 #ifdef CONFIG_DRIVER_TI_EMAC
211 #define CONFIG_MII
212 #define CONFIG_BOOTP_DNS
213 #define CONFIG_BOOTP_DNS2
214 #define CONFIG_BOOTP_SEND_HOSTNAME
215 #define CONFIG_NET_RETRY_COUNT	10
216 #endif
217 
218 #ifdef CONFIG_USE_NOR
219 #define CONFIG_FLASH_CFI_DRIVER
220 #define CONFIG_SYS_FLASH_CFI
221 #define CONFIG_SYS_FLASH_PROTECTION
222 #define CONFIG_SYS_MAX_FLASH_BANKS	1 /* max number of flash banks */
223 #define CONFIG_SYS_FLASH_SECT_SZ	(128 << 10) /* 128KB */
224 #define CONFIG_ENV_OFFSET		(CONFIG_SYS_FLASH_SECT_SZ * 3)
225 #define CONFIG_ENV_SIZE			(10 << 10) /* 10KB */
226 #define CONFIG_SYS_FLASH_BASE		DAVINCI_ASYNC_EMIF_DATA_CE2_BASE
227 #define PHYS_FLASH_SIZE			(8 << 20) /* Flash size 8MB */
228 #define CONFIG_SYS_MAX_FLASH_SECT ((PHYS_FLASH_SIZE/CONFIG_SYS_FLASH_SECT_SZ)\
229 	       + 3)
230 #define CONFIG_ENV_SECT_SIZE		CONFIG_SYS_FLASH_SECT_SZ
231 #endif
232 
233 #ifdef CONFIG_USE_SPIFLASH
234 #define CONFIG_ENV_SIZE			(64 << 10)
235 #define CONFIG_ENV_OFFSET		(512 << 10)
236 #define CONFIG_ENV_SECT_SIZE		(64 << 10)
237 #endif
238 
239 /*
240  * U-Boot general configuration
241  */
242 #define CONFIG_MISC_INIT_R
243 #define CONFIG_BOOTFILE		"uImage" /* Boot file name */
244 #define CONFIG_SYS_CBSIZE	1024 /* Console I/O Buffer Size	*/
245 #define CONFIG_SYS_PBSIZE	(CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
246 #define CONFIG_SYS_MAXARGS	16 /* max number of command args */
247 #define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE /* Boot Args Buffer Size */
248 #define CONFIG_SYS_LOAD_ADDR	(PHYS_SDRAM_1 + 0x700000)
249 #define CONFIG_AUTO_COMPLETE
250 #define CONFIG_CMDLINE_EDITING
251 #define CONFIG_SYS_LONGHELP
252 #define CONFIG_MX_CYCLIC
253 
254 /*
255  * Linux Information
256  */
257 #define LINUX_BOOT_PARAM_ADDR	(PHYS_SDRAM_1 + 0x100)
258 #define CONFIG_HWCONFIG		/* enable hwconfig */
259 #define CONFIG_CMDLINE_TAG
260 #define CONFIG_REVISION_TAG
261 #define CONFIG_SETUP_MEMORY_TAGS
262 #define CONFIG_BOOTARGS		\
263 	"mem=32M console=ttyS2,115200n8 root=/dev/mtdblock2 rw noinitrd ip=dhcp"
264 #define CONFIG_EXTRA_ENV_SETTINGS	"hwconfig=dsp:wake=yes"
265 
266 /*
267  * U-Boot commands
268  */
269 #define CONFIG_CMD_SAVES
270 
271 #ifdef CONFIG_CMD_BDI
272 #define CONFIG_CLOCKS
273 #endif
274 
275 #ifndef CONFIG_DRIVER_TI_EMAC
276 #endif
277 
278 #ifdef CONFIG_USE_NAND
279 #define CONFIG_CMD_NAND
280 
281 #define CONFIG_MTD_DEVICE
282 #define CONFIG_MTD_PARTITIONS
283 #endif
284 
285 #ifdef CONFIG_USE_SPIFLASH
286 #endif
287 
288 #if !defined(CONFIG_USE_NAND) && \
289 	!defined(CONFIG_USE_NOR) && \
290 	!defined(CONFIG_USE_SPIFLASH)
291 #define CONFIG_ENV_SIZE		(16 << 10)
292 #endif
293 
294 #ifndef CONFIG_DIRECT_NOR_BOOT
295 /* defines for SPL */
296 #define CONFIG_SPL_FRAMEWORK
297 #define CONFIG_SYS_SPL_MALLOC_START	(CONFIG_SYS_TEXT_BASE - \
298 						CONFIG_SYS_MALLOC_LEN)
299 #define CONFIG_SYS_SPL_MALLOC_SIZE	CONFIG_SYS_MALLOC_LEN
300 #define CONFIG_SPL_SPI_LOAD
301 #define CONFIG_SPL_LDSCRIPT	"board/$(BOARDDIR)/u-boot-spl-da850evm.lds"
302 #define CONFIG_SPL_STACK	0x8001ff00
303 #define CONFIG_SPL_TEXT_BASE	0x80000000
304 #define CONFIG_SPL_MAX_FOOTPRINT	32768
305 #define CONFIG_SPL_PAD_TO	32768
306 #endif
307 
308 /* Load U-Boot Image From MMC */
309 #ifdef CONFIG_SPL_MMC_LOAD
310 #undef CONFIG_SPL_SPI_LOAD
311 #endif
312 
313 /* additions for new relocation code, must added to all boards */
314 #define CONFIG_SYS_SDRAM_BASE		0xc0000000
315 
316 #ifdef CONFIG_DIRECT_NOR_BOOT
317 #define CONFIG_SYS_INIT_SP_ADDR		0x8001ff00
318 #else
319 #define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_SDRAM_BASE + 0x1000 - /* Fix this */ \
320 					GENERATED_GBL_DATA_SIZE)
321 #endif /* CONFIG_DIRECT_NOR_BOOT */
322 
323 #include <asm/arch/hardware.h>
324 
325 #endif /* __CONFIG_H */
326