1 /* SPDX-License-Identifier: GPL-2.0+ */ 2 /* 3 * Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/ 4 * 5 * Based on davinci_dvevm.h. Original Copyrights follow: 6 * 7 * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net> 8 */ 9 10 #ifndef __CONFIG_H 11 #define __CONFIG_H 12 13 /* 14 * Board 15 */ 16 #define CONFIG_DRIVER_TI_EMAC 17 /* check if direct NOR boot config is used */ 18 #ifndef CONFIG_DIRECT_NOR_BOOT 19 #define CONFIG_USE_SPIFLASH 20 #endif 21 22 /* 23 * Disable DM_* for SPL build and can be re-enabled after adding 24 * DM support in SPL 25 */ 26 #ifdef CONFIG_SPL_BUILD 27 #undef CONFIG_DM_SPI 28 #undef CONFIG_DM_SPI_FLASH 29 #undef CONFIG_DM_I2C 30 #undef CONFIG_DM_I2C_COMPAT 31 #endif 32 /* 33 * SoC Configuration 34 */ 35 #define CONFIG_SYS_EXCEPTION_VECTORS_HIGH 36 #define CONFIG_SYS_CLK_FREQ clk_get(DAVINCI_ARM_CLKID) 37 #define CONFIG_SYS_OSCIN_FREQ 24000000 38 #define CONFIG_SYS_TIMERBASE DAVINCI_TIMER0_BASE 39 #define CONFIG_SYS_HZ_CLOCK clk_get(DAVINCI_AUXCLK_CLKID) 40 41 #ifdef CONFIG_DIRECT_NOR_BOOT 42 #define CONFIG_ARCH_CPU_INIT 43 #define CONFIG_SYS_DV_NOR_BOOT_CFG (0x11) 44 #endif 45 46 /* 47 * Memory Info 48 */ 49 #define CONFIG_SYS_MALLOC_LEN (0x10000 + 1*1024*1024) /* malloc() len */ 50 #define PHYS_SDRAM_1 DAVINCI_DDR_EMIF_DATA_BASE /* DDR Start */ 51 #define PHYS_SDRAM_1_SIZE (64 << 20) /* SDRAM size 64MB */ 52 #define CONFIG_MAX_RAM_BANK_SIZE (512 << 20) /* max size from SPRS586*/ 53 54 /* memtest start addr */ 55 #define CONFIG_SYS_MEMTEST_START (PHYS_SDRAM_1 + 0x2000000) 56 57 /* memtest will be run on 16MB */ 58 #define CONFIG_SYS_MEMTEST_END (PHYS_SDRAM_1 + 0x2000000 + 16*1024*1024) 59 60 #define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */ 61 62 #define CONFIG_SYS_DA850_SYSCFG_SUSPSRC ( \ 63 DAVINCI_SYSCFG_SUSPSRC_TIMER0 | \ 64 DAVINCI_SYSCFG_SUSPSRC_SPI1 | \ 65 DAVINCI_SYSCFG_SUSPSRC_UART2 | \ 66 DAVINCI_SYSCFG_SUSPSRC_EMAC | \ 67 DAVINCI_SYSCFG_SUSPSRC_I2C) 68 69 /* 70 * PLL configuration 71 */ 72 73 #define CONFIG_SYS_DA850_PLL0_PLLM 24 74 #define CONFIG_SYS_DA850_PLL1_PLLM 21 75 76 /* 77 * DDR2 memory configuration 78 */ 79 #define CONFIG_SYS_DA850_DDR2_DDRPHYCR (DV_DDR_PHY_PWRDNEN | \ 80 DV_DDR_PHY_EXT_STRBEN | \ 81 (0x4 << DV_DDR_PHY_RD_LATENCY_SHIFT)) 82 83 #define CONFIG_SYS_DA850_DDR2_SDBCR ( \ 84 (1 << DV_DDR_SDCR_MSDRAMEN_SHIFT) | \ 85 (1 << DV_DDR_SDCR_DDREN_SHIFT) | \ 86 (1 << DV_DDR_SDCR_SDRAMEN_SHIFT) | \ 87 (1 << DV_DDR_SDCR_BUS_WIDTH_SHIFT) | \ 88 (0x3 << DV_DDR_SDCR_CL_SHIFT) | \ 89 (0x2 << DV_DDR_SDCR_IBANK_SHIFT) | \ 90 (0x2 << DV_DDR_SDCR_PAGESIZE_SHIFT)) 91 92 /* SDBCR2 is only used if IBANK_POS bit in SDBCR is set */ 93 #define CONFIG_SYS_DA850_DDR2_SDBCR2 0 94 95 #define CONFIG_SYS_DA850_DDR2_SDTIMR ( \ 96 (14 << DV_DDR_SDTMR1_RFC_SHIFT) | \ 97 (2 << DV_DDR_SDTMR1_RP_SHIFT) | \ 98 (2 << DV_DDR_SDTMR1_RCD_SHIFT) | \ 99 (1 << DV_DDR_SDTMR1_WR_SHIFT) | \ 100 (5 << DV_DDR_SDTMR1_RAS_SHIFT) | \ 101 (8 << DV_DDR_SDTMR1_RC_SHIFT) | \ 102 (1 << DV_DDR_SDTMR1_RRD_SHIFT) | \ 103 (0 << DV_DDR_SDTMR1_WTR_SHIFT)) 104 105 #define CONFIG_SYS_DA850_DDR2_SDTIMR2 ( \ 106 (7 << DV_DDR_SDTMR2_RASMAX_SHIFT) | \ 107 (0 << DV_DDR_SDTMR2_XP_SHIFT) | \ 108 (0 << DV_DDR_SDTMR2_ODT_SHIFT) | \ 109 (17 << DV_DDR_SDTMR2_XSNR_SHIFT) | \ 110 (199 << DV_DDR_SDTMR2_XSRD_SHIFT) | \ 111 (0 << DV_DDR_SDTMR2_RTP_SHIFT) | \ 112 (0 << DV_DDR_SDTMR2_CKE_SHIFT)) 113 114 #define CONFIG_SYS_DA850_DDR2_SDRCR 0x00000494 115 #define CONFIG_SYS_DA850_DDR2_PBBPR 0x30 116 117 /* 118 * Serial Driver info 119 */ 120 121 #if defined(CONFIG_SPL_BUILD) || defined(CONFIG_DIRECT_NOR_BOOT) 122 #define CONFIG_SYS_NS16550_SERIAL 123 #define CONFIG_SYS_NS16550_REG_SIZE -4 /* NS16550 register size */ 124 #define CONFIG_SYS_NS16550_COM1 DAVINCI_UART2_BASE /* Base address of UART2 */ 125 #endif 126 #define CONFIG_SYS_NS16550_CLK clk_get(DAVINCI_UART2_CLKID) 127 128 #define CONFIG_SYS_SPI_CLK clk_get(DAVINCI_SPI1_CLKID) 129 #ifdef CONFIG_SPL_BUILD 130 #define CONFIG_SYS_SPI_BASE DAVINCI_SPI1_BASE 131 #define CONFIG_SF_DEFAULT_SPEED 30000000 132 #define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED 133 #endif 134 135 #ifdef CONFIG_USE_SPIFLASH 136 #define CONFIG_SYS_SPI_U_BOOT_OFFS 0x8000 137 #define CONFIG_SYS_SPI_U_BOOT_SIZE 0x40000 138 #endif 139 140 /* 141 * I2C Configuration 142 */ 143 #ifndef CONFIG_SPL_BUILD 144 #define CONFIG_SYS_I2C_DAVINCI 145 #define CONFIG_SYS_I2C_EXPANDER_ADDR 0x20 146 #endif 147 148 /* 149 * Flash & Environment 150 */ 151 #ifdef CONFIG_USE_NAND 152 #define CONFIG_NAND_DAVINCI 153 #define CONFIG_ENV_OFFSET 0x0 /* Block 0--not used by bootcode */ 154 #define CONFIG_ENV_SIZE (128 << 10) 155 #define CONFIG_SYS_NAND_USE_FLASH_BBT 156 #define CONFIG_SYS_NAND_4BIT_HW_ECC_OOBFIRST 157 #define CONFIG_SYS_NAND_PAGE_2K 158 #define CONFIG_SYS_NAND_CS 3 159 #define CONFIG_SYS_NAND_BASE DAVINCI_ASYNC_EMIF_DATA_CE3_BASE 160 #define CONFIG_SYS_NAND_MASK_CLE 0x10 161 #define CONFIG_SYS_NAND_MASK_ALE 0x8 162 #undef CONFIG_SYS_NAND_HW_ECC 163 #define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */ 164 #define CONFIG_SYS_NAND_HW_ECC_OOBFIRST 165 #define CONFIG_SYS_NAND_5_ADDR_CYCLE 166 #define CONFIG_SYS_NAND_PAGE_SIZE (2 << 10) 167 #define CONFIG_SYS_NAND_BLOCK_SIZE (128 << 10) 168 #define CONFIG_SYS_NAND_U_BOOT_OFFS 0x28000 169 #define CONFIG_SYS_NAND_U_BOOT_SIZE 0x60000 170 #define CONFIG_SYS_NAND_U_BOOT_DST 0xc1080000 171 #define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST 172 #define CONFIG_SYS_NAND_U_BOOT_RELOC_SP (CONFIG_SYS_NAND_U_BOOT_DST - \ 173 CONFIG_SYS_NAND_U_BOOT_SIZE - \ 174 CONFIG_SYS_MALLOC_LEN - \ 175 GENERATED_GBL_DATA_SIZE) 176 #define CONFIG_SYS_NAND_ECCPOS { \ 177 24, 25, 26, 27, 28, \ 178 29, 30, 31, 32, 33, 34, 35, 36, 37, 38, \ 179 39, 40, 41, 42, 43, 44, 45, 46, 47, 48, \ 180 49, 50, 51, 52, 53, 54, 55, 56, 57, 58, \ 181 59, 60, 61, 62, 63 } 182 #define CONFIG_SYS_NAND_PAGE_COUNT 64 183 #define CONFIG_SYS_NAND_BAD_BLOCK_POS 0 184 #define CONFIG_SYS_NAND_ECCSIZE 512 185 #define CONFIG_SYS_NAND_ECCBYTES 10 186 #define CONFIG_SYS_NAND_OOBSIZE 64 187 #define CONFIG_SPL_NAND_BASE 188 #define CONFIG_SPL_NAND_DRIVERS 189 #define CONFIG_SPL_NAND_ECC 190 #define CONFIG_SPL_NAND_LOAD 191 #endif 192 193 /* 194 * Network & Ethernet Configuration 195 */ 196 #ifdef CONFIG_DRIVER_TI_EMAC 197 #define CONFIG_MII 198 #define CONFIG_BOOTP_DNS2 199 #define CONFIG_BOOTP_SEND_HOSTNAME 200 #define CONFIG_NET_RETRY_COUNT 10 201 #endif 202 203 #ifdef CONFIG_USE_NOR 204 #define CONFIG_FLASH_CFI_DRIVER 205 #define CONFIG_SYS_FLASH_CFI 206 #define CONFIG_SYS_FLASH_PROTECTION 207 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of flash banks */ 208 #define CONFIG_SYS_FLASH_SECT_SZ (128 << 10) /* 128KB */ 209 #define CONFIG_ENV_OFFSET (CONFIG_SYS_FLASH_SECT_SZ * 3) 210 #define CONFIG_ENV_SIZE (10 << 10) /* 10KB */ 211 #define CONFIG_SYS_FLASH_BASE DAVINCI_ASYNC_EMIF_DATA_CE2_BASE 212 #define PHYS_FLASH_SIZE (8 << 20) /* Flash size 8MB */ 213 #define CONFIG_SYS_MAX_FLASH_SECT ((PHYS_FLASH_SIZE/CONFIG_SYS_FLASH_SECT_SZ)\ 214 + 3) 215 #define CONFIG_ENV_SECT_SIZE CONFIG_SYS_FLASH_SECT_SZ 216 #endif 217 218 #ifdef CONFIG_USE_SPIFLASH 219 #define CONFIG_ENV_SIZE (64 << 10) 220 #define CONFIG_ENV_OFFSET (512 << 10) 221 #define CONFIG_ENV_SECT_SIZE (64 << 10) 222 #ifdef CONFIG_SPL_BUILD 223 #undef CONFIG_SPI_FLASH_MTD 224 #endif 225 #define CONFIG_MTD_DEVICE /* needed for mtdparts commands */ 226 #define CONFIG_MTD_PARTITIONS /* required for UBI partition support */ 227 #endif 228 229 #define CONFIG_DA8XX_GPIO 230 /* 231 * U-Boot general configuration 232 */ 233 #define CONFIG_MISC_INIT_R 234 #define CONFIG_BOOTFILE "uImage" /* Boot file name */ 235 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 236 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Args Buffer Size */ 237 #define CONFIG_SYS_LOAD_ADDR (PHYS_SDRAM_1 + 0x700000) 238 #define CONFIG_MX_CYCLIC 239 240 /* 241 * Linux Information 242 */ 243 #define LINUX_BOOT_PARAM_ADDR (PHYS_SDRAM_1 + 0x100) 244 #define CONFIG_HWCONFIG /* enable hwconfig */ 245 #define CONFIG_CMDLINE_TAG 246 #define CONFIG_REVISION_TAG 247 #define CONFIG_SETUP_MEMORY_TAGS 248 249 #define CONFIG_BOOTCOMMAND \ 250 "run envboot; " \ 251 "run mmcboot; " 252 253 #define DEFAULT_LINUX_BOOT_ENV \ 254 "loadaddr=0xc0700000\0" \ 255 "fdtaddr=0xc0600000\0" \ 256 "scriptaddr=0xc0600000\0" 257 258 #include <environment/ti/mmc.h> 259 260 #define CONFIG_EXTRA_ENV_SETTINGS \ 261 DEFAULT_LINUX_BOOT_ENV \ 262 DEFAULT_MMC_TI_ARGS \ 263 "bootpart=0:2\0" \ 264 "bootdir=/boot\0" \ 265 "bootfile=zImage\0" \ 266 "fdtfile=da850-evm.dtb\0" \ 267 "boot_fdt=yes\0" \ 268 "boot_fit=0\0" \ 269 "console=ttyS2,115200n8\0" \ 270 "hwconfig=dsp:wake=yes" 271 272 #ifdef CONFIG_CMD_BDI 273 #define CONFIG_CLOCKS 274 #endif 275 276 #ifdef CONFIG_USE_NAND 277 #define CONFIG_MTD_DEVICE 278 #define CONFIG_MTD_PARTITIONS 279 #endif 280 281 #if !defined(CONFIG_USE_NAND) && \ 282 !defined(CONFIG_USE_NOR) && \ 283 !defined(CONFIG_USE_SPIFLASH) 284 #define CONFIG_ENV_SIZE (16 << 10) 285 #endif 286 287 #ifndef CONFIG_DIRECT_NOR_BOOT 288 /* defines for SPL */ 289 #define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SYS_TEXT_BASE - \ 290 CONFIG_SYS_MALLOC_LEN) 291 #define CONFIG_SYS_SPL_MALLOC_SIZE CONFIG_SYS_MALLOC_LEN 292 #define CONFIG_SPL_STACK 0x8001ff00 293 #define CONFIG_SPL_TEXT_BASE 0x80000000 294 #define CONFIG_SPL_MAX_FOOTPRINT 32768 295 #define CONFIG_SPL_PAD_TO 32768 296 #endif 297 298 /* Load U-Boot Image From MMC */ 299 300 /* additions for new relocation code, must added to all boards */ 301 #define CONFIG_SYS_SDRAM_BASE 0xc0000000 302 303 #ifdef CONFIG_DIRECT_NOR_BOOT 304 #define CONFIG_SYS_INIT_SP_ADDR 0x8001ff00 305 #else 306 #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x1000 - /* Fix this */ \ 307 GENERATED_GBL_DATA_SIZE) 308 #endif /* CONFIG_DIRECT_NOR_BOOT */ 309 310 #include <asm/arch/hardware.h> 311 312 #endif /* __CONFIG_H */ 313