1 /* 2 * Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/ 3 * 4 * Based on davinci_dvevm.h. Original Copyrights follow: 5 * 6 * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net> 7 * 8 * SPDX-License-Identifier: GPL-2.0+ 9 */ 10 11 #ifndef __CONFIG_H 12 #define __CONFIG_H 13 14 /* 15 * Board 16 */ 17 #define CONFIG_DRIVER_TI_EMAC 18 /* check if direct NOR boot config is used */ 19 #ifndef CONFIG_DIRECT_NOR_BOOT 20 #define CONFIG_USE_SPIFLASH 21 #endif 22 23 /* 24 * Disable DM_* for SPL build and can be re-enabled after adding 25 * DM support in SPL 26 */ 27 #ifdef CONFIG_SPL_BUILD 28 #undef CONFIG_DM_SPI 29 #undef CONFIG_DM_SPI_FLASH 30 #undef CONFIG_DM_I2C 31 #undef CONFIG_DM_I2C_COMPAT 32 #endif 33 /* 34 * SoC Configuration 35 */ 36 #define CONFIG_MACH_DAVINCI_DA850_EVM 37 #define CONFIG_SOC_DA8XX /* TI DA8xx SoC */ 38 #define CONFIG_SOC_DA850 /* TI DA850 SoC */ 39 #define CONFIG_SYS_EXCEPTION_VECTORS_HIGH 40 #define CONFIG_SYS_CLK_FREQ clk_get(DAVINCI_ARM_CLKID) 41 #define CONFIG_SYS_OSCIN_FREQ 24000000 42 #define CONFIG_SYS_TIMERBASE DAVINCI_TIMER0_BASE 43 #define CONFIG_SYS_HZ_CLOCK clk_get(DAVINCI_AUXCLK_CLKID) 44 45 #ifdef CONFIG_DIRECT_NOR_BOOT 46 #define CONFIG_ARCH_CPU_INIT 47 #define CONFIG_DA8XX_GPIO 48 #define CONFIG_SYS_TEXT_BASE 0x60000000 49 #define CONFIG_SYS_DV_NOR_BOOT_CFG (0x11) 50 #define CONFIG_DA850_LOWLEVEL 51 #else 52 #define CONFIG_SYS_TEXT_BASE 0xc1080000 53 #endif 54 55 /* 56 * Memory Info 57 */ 58 #define CONFIG_SYS_MALLOC_LEN (0x10000 + 1*1024*1024) /* malloc() len */ 59 #define PHYS_SDRAM_1 DAVINCI_DDR_EMIF_DATA_BASE /* DDR Start */ 60 #define PHYS_SDRAM_1_SIZE (64 << 20) /* SDRAM size 64MB */ 61 #define CONFIG_MAX_RAM_BANK_SIZE (512 << 20) /* max size from SPRS586*/ 62 63 /* memtest start addr */ 64 #define CONFIG_SYS_MEMTEST_START (PHYS_SDRAM_1 + 0x2000000) 65 66 /* memtest will be run on 16MB */ 67 #define CONFIG_SYS_MEMTEST_END (PHYS_SDRAM_1 + 0x2000000 + 16*1024*1024) 68 69 #define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */ 70 71 #define CONFIG_SYS_DA850_SYSCFG_SUSPSRC ( \ 72 DAVINCI_SYSCFG_SUSPSRC_TIMER0 | \ 73 DAVINCI_SYSCFG_SUSPSRC_SPI1 | \ 74 DAVINCI_SYSCFG_SUSPSRC_UART2 | \ 75 DAVINCI_SYSCFG_SUSPSRC_EMAC | \ 76 DAVINCI_SYSCFG_SUSPSRC_I2C) 77 78 /* 79 * PLL configuration 80 */ 81 #define CONFIG_SYS_DV_CLKMODE 0 82 #define CONFIG_SYS_DA850_PLL0_POSTDIV 1 83 #define CONFIG_SYS_DA850_PLL0_PLLDIV1 0x8000 84 #define CONFIG_SYS_DA850_PLL0_PLLDIV2 0x8001 85 #define CONFIG_SYS_DA850_PLL0_PLLDIV3 0x8002 86 #define CONFIG_SYS_DA850_PLL0_PLLDIV4 0x8003 87 #define CONFIG_SYS_DA850_PLL0_PLLDIV5 0x8002 88 #define CONFIG_SYS_DA850_PLL0_PLLDIV6 CONFIG_SYS_DA850_PLL0_PLLDIV1 89 #define CONFIG_SYS_DA850_PLL0_PLLDIV7 0x8005 90 91 #define CONFIG_SYS_DA850_PLL1_POSTDIV 1 92 #define CONFIG_SYS_DA850_PLL1_PLLDIV1 0x8000 93 #define CONFIG_SYS_DA850_PLL1_PLLDIV2 0x8001 94 #define CONFIG_SYS_DA850_PLL1_PLLDIV3 0x8002 95 96 #define CONFIG_SYS_DA850_PLL0_PLLM 24 97 #define CONFIG_SYS_DA850_PLL1_PLLM 21 98 99 /* 100 * DDR2 memory configuration 101 */ 102 #define CONFIG_SYS_DA850_DDR2_DDRPHYCR (DV_DDR_PHY_PWRDNEN | \ 103 DV_DDR_PHY_EXT_STRBEN | \ 104 (0x4 << DV_DDR_PHY_RD_LATENCY_SHIFT)) 105 106 #define CONFIG_SYS_DA850_DDR2_SDBCR ( \ 107 (1 << DV_DDR_SDCR_MSDRAMEN_SHIFT) | \ 108 (1 << DV_DDR_SDCR_DDREN_SHIFT) | \ 109 (1 << DV_DDR_SDCR_SDRAMEN_SHIFT) | \ 110 (1 << DV_DDR_SDCR_BUS_WIDTH_SHIFT) | \ 111 (0x3 << DV_DDR_SDCR_CL_SHIFT) | \ 112 (0x2 << DV_DDR_SDCR_IBANK_SHIFT) | \ 113 (0x2 << DV_DDR_SDCR_PAGESIZE_SHIFT)) 114 115 /* SDBCR2 is only used if IBANK_POS bit in SDBCR is set */ 116 #define CONFIG_SYS_DA850_DDR2_SDBCR2 0 117 118 #define CONFIG_SYS_DA850_DDR2_SDTIMR ( \ 119 (14 << DV_DDR_SDTMR1_RFC_SHIFT) | \ 120 (2 << DV_DDR_SDTMR1_RP_SHIFT) | \ 121 (2 << DV_DDR_SDTMR1_RCD_SHIFT) | \ 122 (1 << DV_DDR_SDTMR1_WR_SHIFT) | \ 123 (5 << DV_DDR_SDTMR1_RAS_SHIFT) | \ 124 (8 << DV_DDR_SDTMR1_RC_SHIFT) | \ 125 (1 << DV_DDR_SDTMR1_RRD_SHIFT) | \ 126 (0 << DV_DDR_SDTMR1_WTR_SHIFT)) 127 128 #define CONFIG_SYS_DA850_DDR2_SDTIMR2 ( \ 129 (7 << DV_DDR_SDTMR2_RASMAX_SHIFT) | \ 130 (0 << DV_DDR_SDTMR2_XP_SHIFT) | \ 131 (0 << DV_DDR_SDTMR2_ODT_SHIFT) | \ 132 (17 << DV_DDR_SDTMR2_XSNR_SHIFT) | \ 133 (199 << DV_DDR_SDTMR2_XSRD_SHIFT) | \ 134 (0 << DV_DDR_SDTMR2_RTP_SHIFT) | \ 135 (0 << DV_DDR_SDTMR2_CKE_SHIFT)) 136 137 #define CONFIG_SYS_DA850_DDR2_SDRCR 0x00000494 138 #define CONFIG_SYS_DA850_DDR2_PBBPR 0x30 139 140 /* 141 * Serial Driver info 142 */ 143 144 #if defined(CONFIG_SPL_BUILD) || defined(CONFIG_DIRECT_NOR_BOOT) 145 #define CONFIG_SYS_NS16550_SERIAL 146 #define CONFIG_SYS_NS16550_REG_SIZE -4 /* NS16550 register size */ 147 #define CONFIG_SYS_NS16550_COM1 DAVINCI_UART2_BASE /* Base address of UART2 */ 148 #endif 149 #define CONFIG_SYS_NS16550_CLK clk_get(DAVINCI_UART2_CLKID) 150 #define CONFIG_CONS_INDEX 1 /* use UART0 for console */ 151 152 #define CONFIG_SPI 153 #define CONFIG_DAVINCI_SPI 154 #define CONFIG_SYS_SPI_CLK clk_get(DAVINCI_SPI1_CLKID) 155 #ifdef CONFIG_SPL_BUILD 156 #define CONFIG_SYS_SPI_BASE DAVINCI_SPI1_BASE 157 #define CONFIG_SF_DEFAULT_SPEED 30000000 158 #define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED 159 #endif 160 161 #ifdef CONFIG_USE_SPIFLASH 162 #define CONFIG_SPL_SPI_LOAD 163 #define CONFIG_SYS_SPI_U_BOOT_OFFS 0x8000 164 #define CONFIG_SYS_SPI_U_BOOT_SIZE 0x40000 165 #endif 166 167 /* 168 * I2C Configuration 169 */ 170 #define CONFIG_SYS_I2C 171 #define CONFIG_SYS_I2C_DAVINCI 172 #define CONFIG_SYS_DAVINCI_I2C_SPEED 25000 173 #define CONFIG_SYS_DAVINCI_I2C_SLAVE 10 /* Bogus, master-only in U-Boot */ 174 #define CONFIG_SYS_I2C_EXPANDER_ADDR 0x20 175 176 /* 177 * Flash & Environment 178 */ 179 #ifdef CONFIG_USE_NAND 180 #define CONFIG_NAND_DAVINCI 181 #define CONFIG_ENV_OFFSET 0x0 /* Block 0--not used by bootcode */ 182 #define CONFIG_ENV_SIZE (128 << 10) 183 #define CONFIG_SYS_NAND_USE_FLASH_BBT 184 #define CONFIG_SYS_NAND_4BIT_HW_ECC_OOBFIRST 185 #define CONFIG_SYS_NAND_PAGE_2K 186 #define CONFIG_SYS_NAND_CS 3 187 #define CONFIG_SYS_NAND_BASE DAVINCI_ASYNC_EMIF_DATA_CE3_BASE 188 #define CONFIG_SYS_NAND_MASK_CLE 0x10 189 #define CONFIG_SYS_NAND_MASK_ALE 0x8 190 #undef CONFIG_SYS_NAND_HW_ECC 191 #define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */ 192 #define CONFIG_SYS_NAND_HW_ECC_OOBFIRST 193 #define CONFIG_SYS_NAND_5_ADDR_CYCLE 194 #define CONFIG_SYS_NAND_PAGE_SIZE (2 << 10) 195 #define CONFIG_SYS_NAND_BLOCK_SIZE (128 << 10) 196 #define CONFIG_SYS_NAND_U_BOOT_OFFS 0x28000 197 #define CONFIG_SYS_NAND_U_BOOT_SIZE 0x60000 198 #define CONFIG_SYS_NAND_U_BOOT_DST 0xc1080000 199 #define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST 200 #define CONFIG_SYS_NAND_U_BOOT_RELOC_SP (CONFIG_SYS_NAND_U_BOOT_DST - \ 201 CONFIG_SYS_NAND_U_BOOT_SIZE - \ 202 CONFIG_SYS_MALLOC_LEN - \ 203 GENERATED_GBL_DATA_SIZE) 204 #define CONFIG_SYS_NAND_ECCPOS { \ 205 24, 25, 26, 27, 28, \ 206 29, 30, 31, 32, 33, 34, 35, 36, 37, 38, \ 207 39, 40, 41, 42, 43, 44, 45, 46, 47, 48, \ 208 49, 50, 51, 52, 53, 54, 55, 56, 57, 58, \ 209 59, 60, 61, 62, 63 } 210 #define CONFIG_SYS_NAND_PAGE_COUNT 64 211 #define CONFIG_SYS_NAND_BAD_BLOCK_POS 0 212 #define CONFIG_SYS_NAND_ECCSIZE 512 213 #define CONFIG_SYS_NAND_ECCBYTES 10 214 #define CONFIG_SYS_NAND_OOBSIZE 64 215 #define CONFIG_SPL_NAND_BASE 216 #define CONFIG_SPL_NAND_DRIVERS 217 #define CONFIG_SPL_NAND_ECC 218 #define CONFIG_SPL_NAND_SIMPLE 219 #define CONFIG_SPL_NAND_LOAD 220 #endif 221 222 /* 223 * Network & Ethernet Configuration 224 */ 225 #ifdef CONFIG_DRIVER_TI_EMAC 226 #define CONFIG_MII 227 #define CONFIG_BOOTP_DNS 228 #define CONFIG_BOOTP_DNS2 229 #define CONFIG_BOOTP_SEND_HOSTNAME 230 #define CONFIG_NET_RETRY_COUNT 10 231 #endif 232 233 #ifdef CONFIG_USE_NOR 234 #define CONFIG_FLASH_CFI_DRIVER 235 #define CONFIG_SYS_FLASH_CFI 236 #define CONFIG_SYS_FLASH_PROTECTION 237 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of flash banks */ 238 #define CONFIG_SYS_FLASH_SECT_SZ (128 << 10) /* 128KB */ 239 #define CONFIG_ENV_OFFSET (CONFIG_SYS_FLASH_SECT_SZ * 3) 240 #define CONFIG_ENV_SIZE (10 << 10) /* 10KB */ 241 #define CONFIG_SYS_FLASH_BASE DAVINCI_ASYNC_EMIF_DATA_CE2_BASE 242 #define PHYS_FLASH_SIZE (8 << 20) /* Flash size 8MB */ 243 #define CONFIG_SYS_MAX_FLASH_SECT ((PHYS_FLASH_SIZE/CONFIG_SYS_FLASH_SECT_SZ)\ 244 + 3) 245 #define CONFIG_ENV_SECT_SIZE CONFIG_SYS_FLASH_SECT_SZ 246 #endif 247 248 #ifdef CONFIG_USE_SPIFLASH 249 #define CONFIG_ENV_SIZE (64 << 10) 250 #define CONFIG_ENV_OFFSET (512 << 10) 251 #define CONFIG_ENV_SECT_SIZE (64 << 10) 252 #endif 253 254 /* 255 * U-Boot general configuration 256 */ 257 #define CONFIG_MISC_INIT_R 258 #define CONFIG_BOOTFILE "uImage" /* Boot file name */ 259 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 260 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Args Buffer Size */ 261 #define CONFIG_SYS_LOAD_ADDR (PHYS_SDRAM_1 + 0x700000) 262 #define CONFIG_AUTO_COMPLETE 263 #define CONFIG_CMDLINE_EDITING 264 #define CONFIG_SYS_LONGHELP 265 #define CONFIG_MX_CYCLIC 266 267 /* 268 * Linux Information 269 */ 270 #define LINUX_BOOT_PARAM_ADDR (PHYS_SDRAM_1 + 0x100) 271 #define CONFIG_HWCONFIG /* enable hwconfig */ 272 #define CONFIG_CMDLINE_TAG 273 #define CONFIG_REVISION_TAG 274 #define CONFIG_SETUP_MEMORY_TAGS 275 276 #define CONFIG_BOOTCOMMAND \ 277 "run envboot; " \ 278 "run mmcboot; " 279 280 #define DEFAULT_LINUX_BOOT_ENV \ 281 "loadaddr=0xc0700000\0" \ 282 "fdtaddr=0xc0600000\0" \ 283 "scriptaddr=0xc0600000\0" 284 285 #include <environment/ti/mmc.h> 286 287 #define CONFIG_EXTRA_ENV_SETTINGS \ 288 DEFAULT_LINUX_BOOT_ENV \ 289 DEFAULT_MMC_TI_ARGS \ 290 "bootpart=0:2\0" \ 291 "bootdir=/boot\0" \ 292 "bootfile=zImage\0" \ 293 "fdtfile=da850-evm.dtb\0" \ 294 "boot_fdt=yes\0" \ 295 "boot_fit=0\0" \ 296 "console=ttyS2,115200n8\0" \ 297 "hwconfig=dsp:wake=yes" 298 299 #ifdef CONFIG_CMD_BDI 300 #define CONFIG_CLOCKS 301 #endif 302 303 #ifndef CONFIG_DRIVER_TI_EMAC 304 #endif 305 306 #ifdef CONFIG_USE_NAND 307 #define CONFIG_MTD_DEVICE 308 #define CONFIG_MTD_PARTITIONS 309 #endif 310 311 #ifdef CONFIG_USE_SPIFLASH 312 #endif 313 314 #if !defined(CONFIG_USE_NAND) && \ 315 !defined(CONFIG_USE_NOR) && \ 316 !defined(CONFIG_USE_SPIFLASH) 317 #define CONFIG_ENV_SIZE (16 << 10) 318 #endif 319 320 #ifndef CONFIG_DIRECT_NOR_BOOT 321 /* defines for SPL */ 322 #define CONFIG_SPL_FRAMEWORK 323 #define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SYS_TEXT_BASE - \ 324 CONFIG_SYS_MALLOC_LEN) 325 #define CONFIG_SYS_SPL_MALLOC_SIZE CONFIG_SYS_MALLOC_LEN 326 #define CONFIG_SPL_SPI_LOAD 327 #define CONFIG_SPL_STACK 0x8001ff00 328 #define CONFIG_SPL_TEXT_BASE 0x80000000 329 #define CONFIG_SPL_MAX_FOOTPRINT 32768 330 #define CONFIG_SPL_PAD_TO 32768 331 #endif 332 333 /* Load U-Boot Image From MMC */ 334 #ifdef CONFIG_SPL_MMC_LOAD 335 #undef CONFIG_SPL_SPI_LOAD 336 #endif 337 338 /* additions for new relocation code, must added to all boards */ 339 #define CONFIG_SYS_SDRAM_BASE 0xc0000000 340 341 #ifdef CONFIG_DIRECT_NOR_BOOT 342 #define CONFIG_SYS_INIT_SP_ADDR 0x8001ff00 343 #else 344 #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x1000 - /* Fix this */ \ 345 GENERATED_GBL_DATA_SIZE) 346 #endif /* CONFIG_DIRECT_NOR_BOOT */ 347 348 #include <asm/arch/hardware.h> 349 350 #endif /* __CONFIG_H */ 351