1 /* 2 * Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/ 3 * 4 * Based on davinci_dvevm.h. Original Copyrights follow: 5 * 6 * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net> 7 * 8 * SPDX-License-Identifier: GPL-2.0+ 9 */ 10 11 #ifndef __CONFIG_H 12 #define __CONFIG_H 13 14 /* 15 * Board 16 */ 17 #define CONFIG_DRIVER_TI_EMAC 18 /* check if direct NOR boot config is used */ 19 #ifndef CONFIG_DIRECT_NOR_BOOT 20 #define CONFIG_USE_SPIFLASH 21 #endif 22 23 /* 24 * SoC Configuration 25 */ 26 #define CONFIG_MACH_DAVINCI_DA850_EVM 27 #define CONFIG_SOC_DA8XX /* TI DA8xx SoC */ 28 #define CONFIG_SOC_DA850 /* TI DA850 SoC */ 29 #define CONFIG_SYS_EXCEPTION_VECTORS_HIGH 30 #define CONFIG_SYS_CLK_FREQ clk_get(DAVINCI_ARM_CLKID) 31 #define CONFIG_SYS_OSCIN_FREQ 24000000 32 #define CONFIG_SYS_TIMERBASE DAVINCI_TIMER0_BASE 33 #define CONFIG_SYS_HZ_CLOCK clk_get(DAVINCI_AUXCLK_CLKID) 34 #define CONFIG_SYS_DA850_PLL_INIT 35 #define CONFIG_SYS_DA850_DDR_INIT 36 37 #ifdef CONFIG_DIRECT_NOR_BOOT 38 #define CONFIG_ARCH_CPU_INIT 39 #define CONFIG_DA8XX_GPIO 40 #define CONFIG_SYS_TEXT_BASE 0x60000000 41 #define CONFIG_SYS_DV_NOR_BOOT_CFG (0x11) 42 #define CONFIG_DA850_LOWLEVEL 43 #else 44 #define CONFIG_SYS_TEXT_BASE 0xc1080000 45 #endif 46 47 /* 48 * Memory Info 49 */ 50 #define CONFIG_SYS_MALLOC_LEN (0x10000 + 1*1024*1024) /* malloc() len */ 51 #define PHYS_SDRAM_1 DAVINCI_DDR_EMIF_DATA_BASE /* DDR Start */ 52 #define PHYS_SDRAM_1_SIZE (64 << 20) /* SDRAM size 64MB */ 53 #define CONFIG_MAX_RAM_BANK_SIZE (512 << 20) /* max size from SPRS586*/ 54 55 /* memtest start addr */ 56 #define CONFIG_SYS_MEMTEST_START (PHYS_SDRAM_1 + 0x2000000) 57 58 /* memtest will be run on 16MB */ 59 #define CONFIG_SYS_MEMTEST_END (PHYS_SDRAM_1 + 0x2000000 + 16*1024*1024) 60 61 #define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */ 62 63 #define CONFIG_SYS_DA850_SYSCFG_SUSPSRC ( \ 64 DAVINCI_SYSCFG_SUSPSRC_TIMER0 | \ 65 DAVINCI_SYSCFG_SUSPSRC_SPI1 | \ 66 DAVINCI_SYSCFG_SUSPSRC_UART2 | \ 67 DAVINCI_SYSCFG_SUSPSRC_EMAC | \ 68 DAVINCI_SYSCFG_SUSPSRC_I2C) 69 70 /* 71 * PLL configuration 72 */ 73 #define CONFIG_SYS_DV_CLKMODE 0 74 #define CONFIG_SYS_DA850_PLL0_POSTDIV 1 75 #define CONFIG_SYS_DA850_PLL0_PLLDIV1 0x8000 76 #define CONFIG_SYS_DA850_PLL0_PLLDIV2 0x8001 77 #define CONFIG_SYS_DA850_PLL0_PLLDIV3 0x8002 78 #define CONFIG_SYS_DA850_PLL0_PLLDIV4 0x8003 79 #define CONFIG_SYS_DA850_PLL0_PLLDIV5 0x8002 80 #define CONFIG_SYS_DA850_PLL0_PLLDIV6 CONFIG_SYS_DA850_PLL0_PLLDIV1 81 #define CONFIG_SYS_DA850_PLL0_PLLDIV7 0x8005 82 83 #define CONFIG_SYS_DA850_PLL1_POSTDIV 1 84 #define CONFIG_SYS_DA850_PLL1_PLLDIV1 0x8000 85 #define CONFIG_SYS_DA850_PLL1_PLLDIV2 0x8001 86 #define CONFIG_SYS_DA850_PLL1_PLLDIV3 0x8002 87 88 #define CONFIG_SYS_DA850_PLL0_PLLM 24 89 #define CONFIG_SYS_DA850_PLL1_PLLM 21 90 91 /* 92 * DDR2 memory configuration 93 */ 94 #define CONFIG_SYS_DA850_DDR2_DDRPHYCR (DV_DDR_PHY_PWRDNEN | \ 95 DV_DDR_PHY_EXT_STRBEN | \ 96 (0x4 << DV_DDR_PHY_RD_LATENCY_SHIFT)) 97 98 #define CONFIG_SYS_DA850_DDR2_SDBCR ( \ 99 (1 << DV_DDR_SDCR_MSDRAMEN_SHIFT) | \ 100 (1 << DV_DDR_SDCR_DDREN_SHIFT) | \ 101 (1 << DV_DDR_SDCR_SDRAMEN_SHIFT) | \ 102 (1 << DV_DDR_SDCR_BUS_WIDTH_SHIFT) | \ 103 (0x3 << DV_DDR_SDCR_CL_SHIFT) | \ 104 (0x2 << DV_DDR_SDCR_IBANK_SHIFT) | \ 105 (0x2 << DV_DDR_SDCR_PAGESIZE_SHIFT)) 106 107 /* SDBCR2 is only used if IBANK_POS bit in SDBCR is set */ 108 #define CONFIG_SYS_DA850_DDR2_SDBCR2 0 109 110 #define CONFIG_SYS_DA850_DDR2_SDTIMR ( \ 111 (14 << DV_DDR_SDTMR1_RFC_SHIFT) | \ 112 (2 << DV_DDR_SDTMR1_RP_SHIFT) | \ 113 (2 << DV_DDR_SDTMR1_RCD_SHIFT) | \ 114 (1 << DV_DDR_SDTMR1_WR_SHIFT) | \ 115 (5 << DV_DDR_SDTMR1_RAS_SHIFT) | \ 116 (8 << DV_DDR_SDTMR1_RC_SHIFT) | \ 117 (1 << DV_DDR_SDTMR1_RRD_SHIFT) | \ 118 (0 << DV_DDR_SDTMR1_WTR_SHIFT)) 119 120 #define CONFIG_SYS_DA850_DDR2_SDTIMR2 ( \ 121 (7 << DV_DDR_SDTMR2_RASMAX_SHIFT) | \ 122 (0 << DV_DDR_SDTMR2_XP_SHIFT) | \ 123 (0 << DV_DDR_SDTMR2_ODT_SHIFT) | \ 124 (17 << DV_DDR_SDTMR2_XSNR_SHIFT) | \ 125 (199 << DV_DDR_SDTMR2_XSRD_SHIFT) | \ 126 (0 << DV_DDR_SDTMR2_RTP_SHIFT) | \ 127 (0 << DV_DDR_SDTMR2_CKE_SHIFT)) 128 129 #define CONFIG_SYS_DA850_DDR2_SDRCR 0x00000494 130 #define CONFIG_SYS_DA850_DDR2_PBBPR 0x30 131 132 /* 133 * Serial Driver info 134 */ 135 #define CONFIG_SYS_NS16550_SERIAL 136 #define CONFIG_SYS_NS16550_REG_SIZE -4 /* NS16550 register size */ 137 #define CONFIG_SYS_NS16550_COM1 DAVINCI_UART2_BASE /* Base address of UART2 */ 138 #define CONFIG_SYS_NS16550_CLK clk_get(DAVINCI_UART2_CLKID) 139 #define CONFIG_CONS_INDEX 1 /* use UART0 for console */ 140 #define CONFIG_BAUDRATE 115200 /* Default baud rate */ 141 142 #define CONFIG_SPI 143 #define CONFIG_DAVINCI_SPI 144 #define CONFIG_SYS_SPI_BASE DAVINCI_SPI1_BASE 145 #define CONFIG_SYS_SPI_CLK clk_get(DAVINCI_SPI1_CLKID) 146 #define CONFIG_SF_DEFAULT_SPEED 30000000 147 #define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED 148 149 #ifdef CONFIG_USE_SPIFLASH 150 #define CONFIG_SPL_SPI_LOAD 151 #define CONFIG_SYS_SPI_U_BOOT_OFFS 0x8000 152 #define CONFIG_SYS_SPI_U_BOOT_SIZE 0x40000 153 #endif 154 155 /* 156 * I2C Configuration 157 */ 158 #define CONFIG_SYS_I2C 159 #define CONFIG_SYS_I2C_DAVINCI 160 #define CONFIG_SYS_DAVINCI_I2C_SPEED 25000 161 #define CONFIG_SYS_DAVINCI_I2C_SLAVE 10 /* Bogus, master-only in U-Boot */ 162 #define CONFIG_SYS_I2C_EXPANDER_ADDR 0x20 163 164 /* 165 * Flash & Environment 166 */ 167 #ifdef CONFIG_USE_NAND 168 #undef CONFIG_ENV_IS_IN_FLASH 169 #define CONFIG_NAND_DAVINCI 170 #define CONFIG_SYS_NO_FLASH 171 #define CONFIG_ENV_IS_IN_NAND /* U-Boot env in NAND Flash */ 172 #define CONFIG_ENV_OFFSET 0x0 /* Block 0--not used by bootcode */ 173 #define CONFIG_ENV_SIZE (128 << 10) 174 #define CONFIG_SYS_NAND_USE_FLASH_BBT 175 #define CONFIG_SYS_NAND_4BIT_HW_ECC_OOBFIRST 176 #define CONFIG_SYS_NAND_PAGE_2K 177 #define CONFIG_SYS_NAND_CS 3 178 #define CONFIG_SYS_NAND_BASE DAVINCI_ASYNC_EMIF_DATA_CE3_BASE 179 #define CONFIG_SYS_NAND_MASK_CLE 0x10 180 #define CONFIG_SYS_NAND_MASK_ALE 0x8 181 #undef CONFIG_SYS_NAND_HW_ECC 182 #define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */ 183 #define CONFIG_SYS_NAND_HW_ECC_OOBFIRST 184 #define CONFIG_SYS_NAND_5_ADDR_CYCLE 185 #define CONFIG_SYS_NAND_PAGE_SIZE (2 << 10) 186 #define CONFIG_SYS_NAND_BLOCK_SIZE (128 << 10) 187 #define CONFIG_SYS_NAND_U_BOOT_OFFS 0x28000 188 #define CONFIG_SYS_NAND_U_BOOT_SIZE 0x60000 189 #define CONFIG_SYS_NAND_U_BOOT_DST 0xc1080000 190 #define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST 191 #define CONFIG_SYS_NAND_U_BOOT_RELOC_SP (CONFIG_SYS_NAND_U_BOOT_DST - \ 192 CONFIG_SYS_NAND_U_BOOT_SIZE - \ 193 CONFIG_SYS_MALLOC_LEN - \ 194 GENERATED_GBL_DATA_SIZE) 195 #define CONFIG_SYS_NAND_ECCPOS { \ 196 24, 25, 26, 27, 28, \ 197 29, 30, 31, 32, 33, 34, 35, 36, 37, 38, \ 198 39, 40, 41, 42, 43, 44, 45, 46, 47, 48, \ 199 49, 50, 51, 52, 53, 54, 55, 56, 57, 58, \ 200 59, 60, 61, 62, 63 } 201 #define CONFIG_SYS_NAND_PAGE_COUNT 64 202 #define CONFIG_SYS_NAND_BAD_BLOCK_POS 0 203 #define CONFIG_SYS_NAND_ECCSIZE 512 204 #define CONFIG_SYS_NAND_ECCBYTES 10 205 #define CONFIG_SYS_NAND_OOBSIZE 64 206 #define CONFIG_SPL_NAND_BASE 207 #define CONFIG_SPL_NAND_DRIVERS 208 #define CONFIG_SPL_NAND_ECC 209 #define CONFIG_SPL_NAND_SIMPLE 210 #define CONFIG_SPL_NAND_LOAD 211 #endif 212 213 /* 214 * Network & Ethernet Configuration 215 */ 216 #ifdef CONFIG_DRIVER_TI_EMAC 217 #define CONFIG_MII 218 #define CONFIG_BOOTP_DNS 219 #define CONFIG_BOOTP_DNS2 220 #define CONFIG_BOOTP_SEND_HOSTNAME 221 #define CONFIG_NET_RETRY_COUNT 10 222 #endif 223 224 #ifdef CONFIG_USE_NOR 225 #define CONFIG_ENV_IS_IN_FLASH 226 #define CONFIG_FLASH_CFI_DRIVER 227 #define CONFIG_SYS_FLASH_CFI 228 #define CONFIG_SYS_FLASH_PROTECTION 229 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of flash banks */ 230 #define CONFIG_SYS_FLASH_SECT_SZ (128 << 10) /* 128KB */ 231 #define CONFIG_ENV_OFFSET (CONFIG_SYS_FLASH_SECT_SZ * 3) 232 #define CONFIG_ENV_SIZE (10 << 10) /* 10KB */ 233 #define CONFIG_SYS_FLASH_BASE DAVINCI_ASYNC_EMIF_DATA_CE2_BASE 234 #define PHYS_FLASH_SIZE (8 << 20) /* Flash size 8MB */ 235 #define CONFIG_SYS_MAX_FLASH_SECT ((PHYS_FLASH_SIZE/CONFIG_SYS_FLASH_SECT_SZ)\ 236 + 3) 237 #define CONFIG_ENV_SECT_SIZE CONFIG_SYS_FLASH_SECT_SZ 238 #endif 239 240 #ifdef CONFIG_USE_SPIFLASH 241 #undef CONFIG_ENV_IS_IN_FLASH 242 #undef CONFIG_ENV_IS_IN_NAND 243 #define CONFIG_ENV_IS_IN_SPI_FLASH 244 #define CONFIG_ENV_SIZE (64 << 10) 245 #define CONFIG_ENV_OFFSET (512 << 10) 246 #define CONFIG_ENV_SECT_SIZE (64 << 10) 247 #define CONFIG_SYS_NO_FLASH 248 #endif 249 250 /* 251 * U-Boot general configuration 252 */ 253 #define CONFIG_MISC_INIT_R 254 #define CONFIG_BOARD_EARLY_INIT_F 255 #define CONFIG_BOOTFILE "uImage" /* Boot file name */ 256 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 257 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) 258 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 259 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Args Buffer Size */ 260 #define CONFIG_SYS_LOAD_ADDR (PHYS_SDRAM_1 + 0x700000) 261 #define CONFIG_AUTO_COMPLETE 262 #define CONFIG_CMDLINE_EDITING 263 #define CONFIG_SYS_LONGHELP 264 #define CONFIG_CRC32_VERIFY 265 #define CONFIG_MX_CYCLIC 266 267 /* 268 * Linux Information 269 */ 270 #define LINUX_BOOT_PARAM_ADDR (PHYS_SDRAM_1 + 0x100) 271 #define CONFIG_HWCONFIG /* enable hwconfig */ 272 #define CONFIG_CMDLINE_TAG 273 #define CONFIG_REVISION_TAG 274 #define CONFIG_SETUP_MEMORY_TAGS 275 #define CONFIG_BOOTARGS \ 276 "mem=32M console=ttyS2,115200n8 root=/dev/mtdblock2 rw noinitrd ip=dhcp" 277 #define CONFIG_EXTRA_ENV_SETTINGS "hwconfig=dsp:wake=yes" 278 279 /* 280 * U-Boot commands 281 */ 282 #define CONFIG_CMD_ENV 283 #define CONFIG_CMD_DIAG 284 #define CONFIG_CMD_SAVES 285 286 #ifdef CONFIG_CMD_BDI 287 #define CONFIG_CLOCKS 288 #endif 289 290 #ifndef CONFIG_DRIVER_TI_EMAC 291 #endif 292 293 #ifdef CONFIG_USE_NAND 294 #define CONFIG_CMD_NAND 295 296 #define CONFIG_CMD_MTDPARTS 297 #define CONFIG_MTD_DEVICE 298 #define CONFIG_MTD_PARTITIONS 299 #define CONFIG_LZO 300 #define CONFIG_RBTREE 301 #define CONFIG_CMD_UBIFS 302 #endif 303 304 #ifdef CONFIG_USE_SPIFLASH 305 #endif 306 307 #if !defined(CONFIG_USE_NAND) && \ 308 !defined(CONFIG_USE_NOR) && \ 309 !defined(CONFIG_USE_SPIFLASH) 310 #define CONFIG_ENV_IS_NOWHERE 311 #define CONFIG_SYS_NO_FLASH 312 #define CONFIG_ENV_SIZE (16 << 10) 313 #undef CONFIG_CMD_ENV 314 #endif 315 316 /* SD/MMC configuration */ 317 #ifndef CONFIG_USE_NOR 318 #define CONFIG_MMC 319 #define CONFIG_DAVINCI_MMC_SD1 320 #define CONFIG_GENERIC_MMC 321 #define CONFIG_DAVINCI_MMC 322 #endif 323 324 /* 325 * Enable MMC commands only when 326 * MMC support is present 327 */ 328 #ifdef CONFIG_MMC 329 #define CONFIG_DOS_PARTITION 330 #endif 331 332 #ifndef CONFIG_DIRECT_NOR_BOOT 333 /* defines for SPL */ 334 #define CONFIG_SPL_FRAMEWORK 335 #define CONFIG_SPL_BOARD_INIT 336 #define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SYS_TEXT_BASE - \ 337 CONFIG_SYS_MALLOC_LEN) 338 #define CONFIG_SYS_SPL_MALLOC_SIZE CONFIG_SYS_MALLOC_LEN 339 #define CONFIG_SPL_SPI_LOAD 340 #define CONFIG_SPL_LDSCRIPT "board/$(BOARDDIR)/u-boot-spl-da850evm.lds" 341 #define CONFIG_SPL_STACK 0x8001ff00 342 #define CONFIG_SPL_TEXT_BASE 0x80000000 343 #define CONFIG_SPL_MAX_FOOTPRINT 32768 344 #define CONFIG_SPL_PAD_TO 32768 345 #endif 346 347 /* Load U-Boot Image From MMC */ 348 #ifdef CONFIG_SPL_MMC_LOAD 349 #undef CONFIG_SPL_SPI_LOAD 350 #endif 351 352 /* additions for new relocation code, must added to all boards */ 353 #define CONFIG_SYS_SDRAM_BASE 0xc0000000 354 355 #ifdef CONFIG_DIRECT_NOR_BOOT 356 #define CONFIG_SYS_INIT_SP_ADDR 0x8001ff00 357 #else 358 #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x1000 - /* Fix this */ \ 359 GENERATED_GBL_DATA_SIZE) 360 #endif /* CONFIG_DIRECT_NOR_BOOT */ 361 #endif /* __CONFIG_H */ 362