1 /* 2 * Based on corenet_ds.h 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 #ifndef __CONFIG_H 8 #define __CONFIG_H 9 10 #define CONFIG_CYRUS 11 12 #if !defined(CONFIG_ARCH_P5020) && !defined(CONFIG_ARCH_P5040) 13 #error Must call Cyrus CONFIG with a specific CPU enabled. 14 #endif 15 16 #define CONFIG_SDCARD 17 #define CONFIG_FSL_SATA_V2 18 #define CONFIG_PCIE3 19 #define CONFIG_PCIE4 20 #ifdef CONFIG_ARCH_P5020 21 #define CONFIG_SYS_FSL_RAID_ENGINE 22 #define CONFIG_SYS_DPAA_RMAN 23 #endif 24 #define CONFIG_SYS_DPAA_PME 25 26 /* 27 * Corenet DS style board configuration file 28 */ 29 #define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE 30 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc 31 #define CONFIG_SYS_FSL_PBL_PBI board/varisys/cyrus/pbi.cfg 32 #if defined(CONFIG_ARCH_P5020) 33 #define CONFIG_SYS_CLK_FREQ 133000000 34 #define CONFIG_SYS_FSL_PBL_RCW board/varisys/cyrus/rcw_p5020_v2.cfg 35 #elif defined(CONFIG_ARCH_P5040) 36 #define CONFIG_SYS_CLK_FREQ 100000000 37 #define CONFIG_SYS_FSL_PBL_RCW board/varisys/cyrus/rcw_p5040.cfg 38 #endif 39 40 /* High Level Configuration Options */ 41 #define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */ 42 #define CONFIG_MP /* support multiple processors */ 43 44 #define CONFIG_SYS_MMC_MAX_DEVICE 1 45 46 #ifndef CONFIG_SYS_TEXT_BASE 47 #define CONFIG_SYS_TEXT_BASE 0xeff40000 48 #endif 49 50 #define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */ 51 #define CONFIG_SYS_NUM_CPC CONFIG_SYS_NUM_DDR_CTLRS 52 #define CONFIG_PCIE1 /* PCIE controller 1 */ 53 #define CONFIG_PCIE2 /* PCIE controller 2 */ 54 #define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ 55 #define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ 56 57 #define CONFIG_ENV_OVERWRITE 58 59 #if defined(CONFIG_SDCARD) 60 #define CONFIG_SYS_EXTRA_ENV_RELOC 61 #define CONFIG_ENV_IS_IN_MMC 62 #define CONFIG_FSL_FIXED_MMC_LOCATION 63 #define CONFIG_SYS_MMC_ENV_DEV 0 64 #define CONFIG_ENV_SIZE 0x2000 65 #define CONFIG_ENV_OFFSET (512 * 1658) 66 #endif 67 68 /* 69 * These can be toggled for performance analysis, otherwise use default. 70 */ 71 #define CONFIG_SYS_CACHE_STASHING 72 #define CONFIG_BACKSIDE_L2_CACHE 73 #define CONFIG_SYS_INIT_L2CSR0 L2CSR0_L2E 74 #define CONFIG_BTB /* toggle branch predition */ 75 #define CONFIG_DDR_ECC 76 #ifdef CONFIG_DDR_ECC 77 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER 78 #define CONFIG_MEM_INIT_VALUE 0xdeadbeef 79 #endif 80 81 #define CONFIG_ENABLE_36BIT_PHYS 82 83 #ifdef CONFIG_PHYS_64BIT 84 #define CONFIG_ADDR_MAP 85 #define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */ 86 #endif 87 88 /* test POST memory test */ 89 #undef CONFIG_POST 90 #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ 91 #define CONFIG_SYS_MEMTEST_END 0x00400000 92 #define CONFIG_SYS_ALT_MEMTEST 93 #define CONFIG_PANIC_HANG /* do not reset board on panic */ 94 95 /* 96 * Config the L3 Cache as L3 SRAM 97 */ 98 #define CONFIG_SYS_INIT_L3_ADDR CONFIG_RAMBOOT_TEXT_BASE 99 #ifdef CONFIG_PHYS_64BIT 100 #define CONFIG_SYS_INIT_L3_ADDR_PHYS (0xf00000000ull | CONFIG_RAMBOOT_TEXT_BASE) 101 #else 102 #define CONFIG_SYS_INIT_L3_ADDR_PHYS CONFIG_SYS_INIT_L3_ADDR 103 #endif 104 #define CONFIG_SYS_L3_SIZE (1024 << 10) 105 #define CONFIG_SYS_INIT_L3_END (CONFIG_SYS_INIT_L3_ADDR + CONFIG_SYS_L3_SIZE) 106 107 #ifdef CONFIG_PHYS_64BIT 108 #define CONFIG_SYS_DCSRBAR 0xf0000000 109 #define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull 110 #endif 111 112 /* 113 * DDR Setup 114 */ 115 #define CONFIG_VERY_BIG_RAM 116 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 117 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 118 119 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 120 #define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR) 121 122 #define CONFIG_DDR_SPD 123 124 #define CONFIG_SYS_SPD_BUS_NUM 1 125 #define SPD_EEPROM_ADDRESS1 0x51 126 #define SPD_EEPROM_ADDRESS2 0x52 127 #define CONFIG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */ 128 129 /* 130 * Local Bus Definitions 131 */ 132 133 #define CONFIG_SYS_LBC0_BASE 0xe0000000 /* Start of LBC Registers */ 134 #ifdef CONFIG_PHYS_64BIT 135 #define CONFIG_SYS_LBC0_BASE_PHYS 0xfe0000000ull 136 #else 137 #define CONFIG_SYS_LBC0_BASE_PHYS CONFIG_SYS_LBC0_BASE 138 #endif 139 140 #define CONFIG_SYS_LBC1_BASE 0xe1000000 /* Start of LBC Registers */ 141 #ifdef CONFIG_PHYS_64BIT 142 #define CONFIG_SYS_LBC1_BASE_PHYS 0xfe1000000ull 143 #else 144 #define CONFIG_SYS_LBC1_BASE_PHYS CONFIG_SYS_LBC1_BASE 145 #endif 146 147 /* Set the local bus clock 1/16 of platform clock */ 148 #define CONFIG_SYS_LBC_LCRR (LCRR_CLKDIV_16 | LCRR_EADC_1) 149 150 #define CONFIG_SYS_BR0_PRELIM \ 151 (BR_PHYS_ADDR(CONFIG_SYS_LBC0_BASE_PHYS) | BR_PS_16 | BR_V) 152 #define CONFIG_SYS_BR1_PRELIM \ 153 (BR_PHYS_ADDR(CONFIG_SYS_LBC1_BASE_PHYS) | BR_PS_16 | BR_V) 154 155 #define CONFIG_SYS_OR0_PRELIM 0xfff00010 156 #define CONFIG_SYS_OR1_PRELIM 0xfff00010 157 158 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 159 160 #if defined(CONFIG_RAMBOOT_PBL) 161 #define CONFIG_SYS_RAMBOOT 162 #endif 163 164 #define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */ 165 #define CONFIG_MISC_INIT_R 166 167 #define CONFIG_HWCONFIG 168 169 /* define to use L1 as initial stack */ 170 #define CONFIG_L1_INIT_RAM 171 #define CONFIG_SYS_INIT_RAM_LOCK 172 #define CONFIG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */ 173 #ifdef CONFIG_PHYS_64BIT 174 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf 175 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR 176 /* The assembler doesn't like typecast */ 177 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \ 178 ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \ 179 CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW) 180 #else 181 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS CONFIG_SYS_INIT_RAM_ADDR /* Initial L1 address */ 182 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0 183 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS 184 #endif 185 #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 /* Size of used area in RAM */ 186 187 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 188 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 189 190 #define CONFIG_SYS_MONITOR_LEN (768 * 1024) 191 #define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */ 192 193 /* Serial Port - controlled on board with jumper J8 194 * open - index 2 195 * shorted - index 1 196 */ 197 #define CONFIG_CONS_INDEX 1 198 #define CONFIG_SYS_NS16550_SERIAL 199 #define CONFIG_SYS_NS16550_REG_SIZE 1 200 #define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2) 201 202 #define CONFIG_SYS_BAUDRATE_TABLE \ 203 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} 204 205 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500) 206 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600) 207 #define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500) 208 #define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600) 209 210 /* I2C */ 211 #define CONFIG_SYS_I2C 212 #define CONFIG_SYS_I2C_FSL 213 #define CONFIG_I2C_MULTI_BUS 214 #define CONFIG_I2C_CMD_TREE 215 #define CONFIG_SYS_FSL_I2C_SPEED 400000 /* I2C speed and slave address */ 216 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 217 #define CONFIG_SYS_FSL_I2C_OFFSET 0x118000 218 #define CONFIG_SYS_FSL_I2C2_SPEED 400000 /* I2C speed and slave address */ 219 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F 220 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100 221 #define CONFIG_SYS_FSL_I2C3_SPEED 400000 /* I2C speed and slave address */ 222 #define CONFIG_SYS_FSL_I2C3_SLAVE 0x7F 223 #define CONFIG_SYS_FSL_I2C3_OFFSET 0x119000 224 #define CONFIG_SYS_FSL_I2C4_SPEED 400000 /* I2C speed and slave address */ 225 #define CONFIG_SYS_FSL_I2C4_SLAVE 0x7F 226 #define CONFIG_SYS_FSL_I2C4_OFFSET 0x119100 227 228 #define CONFIG_ID_EEPROM 229 #define CONFIG_SYS_I2C_EEPROM_NXID 230 #define CONFIG_SYS_EEPROM_BUS_NUM 0 231 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 232 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 233 234 #define CONFIG_SYS_I2C_GENERIC_MAC 235 #define CONFIG_SYS_I2C_MAC1_BUS 3 236 #define CONFIG_SYS_I2C_MAC1_CHIP_ADDR 0x57 237 #define CONFIG_SYS_I2C_MAC1_DATA_ADDR 0xf2 238 #define CONFIG_SYS_I2C_MAC2_BUS 0 239 #define CONFIG_SYS_I2C_MAC2_CHIP_ADDR 0x50 240 #define CONFIG_SYS_I2C_MAC2_DATA_ADDR 0xfa 241 242 #define CONFIG_CMD_DATE 1 243 #define CONFIG_RTC_MCP79411 1 244 #define CONFIG_SYS_RTC_BUS_NUM 3 245 #define CONFIG_SYS_I2C_RTC_ADDR 0x6f 246 247 /* 248 * eSPI - Enhanced SPI 249 */ 250 251 /* 252 * General PCI 253 * Memory space is mapped 1-1, but I/O space must start from 0. 254 */ 255 256 /* controller 1, direct to uli, tgtid 3, Base address 20000 */ 257 #define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 258 #ifdef CONFIG_PHYS_64BIT 259 #define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 260 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull 261 #else 262 #define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000 263 #define CONFIG_SYS_PCIE1_MEM_PHYS 0x80000000 264 #endif 265 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ 266 #define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000 267 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 268 #ifdef CONFIG_PHYS_64BIT 269 #define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull 270 #else 271 #define CONFIG_SYS_PCIE1_IO_PHYS 0xf8000000 272 #endif 273 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ 274 275 /* controller 2, Slot 2, tgtid 2, Base address 201000 */ 276 #define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 277 #ifdef CONFIG_PHYS_64BIT 278 #define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000 279 #define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull 280 #else 281 #define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000 282 #define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000 283 #endif 284 #define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */ 285 #define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000 286 #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 287 #ifdef CONFIG_PHYS_64BIT 288 #define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull 289 #else 290 #define CONFIG_SYS_PCIE2_IO_PHYS 0xf8010000 291 #endif 292 #define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ 293 294 /* controller 3, Slot 1, tgtid 1, Base address 202000 */ 295 #define CONFIG_SYS_PCIE3_MEM_VIRT 0xc0000000 296 #ifdef CONFIG_PHYS_64BIT 297 #define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000 298 #define CONFIG_SYS_PCIE3_MEM_PHYS 0xc40000000ull 299 #else 300 #define CONFIG_SYS_PCIE3_MEM_BUS 0xc0000000 301 #define CONFIG_SYS_PCIE3_MEM_PHYS 0xc0000000 302 #endif 303 #define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */ 304 #define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000 305 #define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 306 #ifdef CONFIG_PHYS_64BIT 307 #define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull 308 #else 309 #define CONFIG_SYS_PCIE3_IO_PHYS 0xf8020000 310 #endif 311 #define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */ 312 313 /* controller 4, Base address 203000 */ 314 #define CONFIG_SYS_PCIE4_MEM_BUS 0xe0000000 315 #define CONFIG_SYS_PCIE4_MEM_PHYS 0xc60000000ull 316 #define CONFIG_SYS_PCIE4_MEM_SIZE 0x20000000 /* 512M */ 317 #define CONFIG_SYS_PCIE4_IO_BUS 0x00000000 318 #define CONFIG_SYS_PCIE4_IO_PHYS 0xff8030000ull 319 #define CONFIG_SYS_PCIE4_IO_SIZE 0x00010000 /* 64k */ 320 321 /* Qman/Bman */ 322 #define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */ 323 #define CONFIG_SYS_BMAN_NUM_PORTALS 10 324 #define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000 325 #ifdef CONFIG_PHYS_64BIT 326 #define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull 327 #else 328 #define CONFIG_SYS_BMAN_MEM_PHYS CONFIG_SYS_BMAN_MEM_BASE 329 #endif 330 #define CONFIG_SYS_BMAN_MEM_SIZE 0x00200000 331 #define CONFIG_SYS_BMAN_SP_CENA_SIZE 0x4000 332 #define CONFIG_SYS_BMAN_SP_CINH_SIZE 0x1000 333 #define CONFIG_SYS_BMAN_CENA_BASE CONFIG_SYS_BMAN_MEM_BASE 334 #define CONFIG_SYS_BMAN_CENA_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) 335 #define CONFIG_SYS_BMAN_CINH_BASE (CONFIG_SYS_BMAN_MEM_BASE + \ 336 CONFIG_SYS_BMAN_CENA_SIZE) 337 #define CONFIG_SYS_BMAN_CINH_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) 338 #define CONFIG_SYS_BMAN_SWP_ISDR_REG 0xE08 339 #define CONFIG_SYS_QMAN_NUM_PORTALS 10 340 #define CONFIG_SYS_QMAN_MEM_BASE 0xf4200000 341 #ifdef CONFIG_PHYS_64BIT 342 #define CONFIG_SYS_QMAN_MEM_PHYS 0xff4200000ull 343 #else 344 #define CONFIG_SYS_QMAN_MEM_PHYS CONFIG_SYS_QMAN_MEM_BASE 345 #endif 346 #define CONFIG_SYS_QMAN_MEM_SIZE 0x00200000 347 #define CONFIG_SYS_QMAN_SP_CENA_SIZE 0x4000 348 #define CONFIG_SYS_QMAN_SP_CINH_SIZE 0x1000 349 #define CONFIG_SYS_QMAN_CENA_BASE CONFIG_SYS_QMAN_MEM_BASE 350 #define CONFIG_SYS_QMAN_CENA_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) 351 #define CONFIG_SYS_QMAN_CINH_BASE (CONFIG_SYS_QMAN_MEM_BASE + \ 352 CONFIG_SYS_QMAN_CENA_SIZE) 353 #define CONFIG_SYS_QMAN_CINH_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) 354 #define CONFIG_SYS_QMAN_SWP_ISDR_REG 0xE08 355 356 #define CONFIG_SYS_DPAA_FMAN 357 /* Default address of microcode for the Linux Fman driver */ 358 /* 359 * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is 360 * about 825KB (1650 blocks), Env is stored after the image, and the env size is 361 * 0x2000 (16 blocks), 8 + 1650 + 16 = 1674, enlarge it to 1680. 362 */ 363 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC 364 #define CONFIG_SYS_FMAN_FW_ADDR (512 * 1680) 365 366 #define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 367 #define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) 368 369 #ifdef CONFIG_SYS_DPAA_FMAN 370 #define CONFIG_FMAN_ENET 371 #define CONFIG_PHY_MICREL 372 #define CONFIG_PHY_MICREL_KSZ9021 373 #endif 374 375 #ifdef CONFIG_PCI 376 #define CONFIG_PCI_INDIRECT_BRIDGE 377 #define CONFIG_NET_MULTI 378 379 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 380 #endif /* CONFIG_PCI */ 381 382 /* SATA */ 383 #ifdef CONFIG_FSL_SATA_V2 384 #define CONFIG_LIBATA 385 #define CONFIG_FSL_SATA 386 387 #define CONFIG_SYS_SATA_MAX_DEVICE 2 388 #define CONFIG_SATA1 389 #define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR 390 #define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA 391 #define CONFIG_SATA2 392 #define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR 393 #define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA 394 395 #define CONFIG_LBA48 396 #define CONFIG_CMD_SATA 397 #endif 398 399 #ifdef CONFIG_FMAN_ENET 400 #define CONFIG_SYS_TBIPA_VALUE 8 401 #define CONFIG_MII /* MII PHY management */ 402 #define CONFIG_ETHPRIME "FM1@DTSEC4" 403 #define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ 404 #endif 405 406 /* 407 * Environment 408 */ 409 #define CONFIG_LOADS_ECHO /* echo on for serial download */ 410 #define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ 411 412 /* 413 * Command line configuration. 414 */ 415 #define CONFIG_CMD_ERRATA 416 #define CONFIG_CMD_IRQ 417 #define CONFIG_CMD_REGINFO 418 419 #ifdef CONFIG_PCI 420 #define CONFIG_CMD_PCI 421 #endif 422 423 /* 424 * USB 425 */ 426 #define CONFIG_HAS_FSL_DR_USB 427 #define CONFIG_HAS_FSL_MPH_USB 428 429 #if defined(CONFIG_HAS_FSL_DR_USB) || defined(CONFIG_HAS_FSL_MPH_USB) 430 #define CONFIG_USB_EHCI 431 #define CONFIG_USB_EHCI_FSL 432 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET 433 #define CONFIG_EHCI_IS_TDI 434 #define CONFIG_SYS_USB_EVENT_POLL 435 /* _VIA_CONTROL_EP */ 436 #endif 437 438 #ifdef CONFIG_MMC 439 #define CONFIG_FSL_ESDHC 440 #define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR 441 #define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT 442 #endif 443 444 /* 445 * Miscellaneous configurable options 446 */ 447 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 448 #define CONFIG_CMDLINE_EDITING /* Command-line editing */ 449 #define CONFIG_AUTO_COMPLETE /* add autocompletion support */ 450 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 451 #ifdef CONFIG_CMD_KGDB 452 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 453 #else 454 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 455 #endif 456 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ 457 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 458 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ 459 460 /* 461 * For booting Linux, the board info and command line data 462 * have to be in the first 64 MB of memory, since this is 463 * the maximum mapped by the Linux kernel during initialization. 464 */ 465 #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux*/ 466 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 467 468 #ifdef CONFIG_CMD_KGDB 469 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ 470 #endif 471 472 /* 473 * Environment Configuration 474 */ 475 #define CONFIG_ROOTPATH "/opt/nfsroot" 476 #define CONFIG_BOOTFILE "uImage" 477 #define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */ 478 479 /* default location for tftp and bootm */ 480 #define CONFIG_LOADADDR 1000000 481 482 483 #define CONFIG_BAUDRATE 115200 484 485 #define __USB_PHY_TYPE utmi 486 487 #define CONFIG_EXTRA_ENV_SETTINGS \ 488 "hwconfig=fsl_ddr:ctlr_intlv=cacheline," \ 489 "bank_intlv=cs0_cs1;" \ 490 "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) ";"\ 491 "usb2:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\ 492 "netdev=eth0\0" \ 493 "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ 494 "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \ 495 "consoledev=ttyS0\0" \ 496 "ramdiskaddr=2000000\0" \ 497 "fdtaddr=1e00000\0" \ 498 "bdev=sda3\0" 499 500 #define CONFIG_HDBOOT \ 501 "setenv bootargs root=/dev/$bdev rw " \ 502 "console=$consoledev,$baudrate $othbootargs;" \ 503 "tftp $loadaddr $bootfile;" \ 504 "tftp $fdtaddr $fdtfile;" \ 505 "bootm $loadaddr - $fdtaddr" 506 507 #define CONFIG_NFSBOOTCOMMAND \ 508 "setenv bootargs root=/dev/nfs rw " \ 509 "nfsroot=$serverip:$rootpath " \ 510 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 511 "console=$consoledev,$baudrate $othbootargs;" \ 512 "tftp $loadaddr $bootfile;" \ 513 "tftp $fdtaddr $fdtfile;" \ 514 "bootm $loadaddr - $fdtaddr" 515 516 #define CONFIG_RAMBOOTCOMMAND \ 517 "setenv bootargs root=/dev/ram rw " \ 518 "console=$consoledev,$baudrate $othbootargs;" \ 519 "tftp $ramdiskaddr $ramdiskfile;" \ 520 "tftp $loadaddr $bootfile;" \ 521 "tftp $fdtaddr $fdtfile;" \ 522 "bootm $loadaddr $ramdiskaddr $fdtaddr" 523 524 #define CONFIG_BOOTCOMMAND CONFIG_HDBOOT 525 526 #include <asm/fsl_secure_boot.h> 527 528 #ifdef CONFIG_SECURE_BOOT 529 #endif 530 531 #endif /* __CONFIG_H */ 532