1 /* 2 * Copyright (C) 2014 Stefan Roese <sr@denx.de> 3 * Copyright (C) 2016 Mario Six <mario.six@gdsys.cc> 4 * 5 * SPDX-License-Identifier: GPL-2.0+ 6 */ 7 8 #ifndef _CONFIG_CONTROLCENTERDC_H 9 #define _CONFIG_CONTROLCENTERDC_H 10 11 /* 12 * High Level Configuration Options (easy to change) 13 */ 14 #define CONFIG_CUSTOMER_BOARD_SUPPORT 15 16 #define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */ 17 #define CONFIG_DISPLAY_BOARDINFO_LATE 18 #define CONFIG_BOARD_LATE_INIT 19 #define CONFIG_LAST_STAGE_INIT 20 21 /* 22 * TEXT_BASE needs to be below 16MiB, since this area is scrubbed 23 * for DDR ECC byte filling in the SPL before loading the main 24 * U-Boot into it. 25 */ 26 #define CONFIG_SYS_TEXT_BASE 0x00800000 27 28 #define CONFIG_SYS_TCLK 250000000 /* 250MHz */ 29 30 #define CONFIG_LOADADDR 1000000 31 32 /* 33 * Commands configuration 34 */ 35 #define CONFIG_CMD_I2C 36 #define CONFIG_CMD_SPI 37 38 /* SPI NOR flash default params, used by sf commands */ 39 #define CONFIG_SF_DEFAULT_BUS 1 40 #define CONFIG_SF_DEFAULT_SPEED 1000000 41 #define CONFIG_SF_DEFAULT_MODE SPI_MODE_3 42 43 /* 44 * SDIO/MMC Card Configuration 45 */ 46 #define CONFIG_SYS_MMC_BASE MVEBU_SDIO_BASE 47 48 /* 49 * SATA/SCSI/AHCI configuration 50 */ 51 #define CONFIG_LIBATA 52 #define CONFIG_SCSI_AHCI 53 #define CONFIG_SCSI_AHCI_PLAT 54 #define CONFIG_SYS_SCSI_MAX_SCSI_ID 2 55 #define CONFIG_SYS_SCSI_MAX_LUN 1 56 #define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \ 57 CONFIG_SYS_SCSI_MAX_LUN) 58 59 /* Additional FS support/configuration */ 60 #define CONFIG_SUPPORT_VFAT 61 62 /* USB/EHCI configuration */ 63 #define CONFIG_EHCI_IS_TDI 64 65 /* Environment in SPI NOR flash */ 66 #define CONFIG_ENV_SPI_BUS 1 67 #define CONFIG_ENV_OFFSET (1 << 20) /* 1MiB in */ 68 #define CONFIG_ENV_SIZE (64 << 10) /* 64KiB */ 69 #define CONFIG_ENV_SECT_SIZE (256 << 10) /* 256KiB sectors */ 70 71 #define CONFIG_PHY_MARVELL /* there is a marvell phy */ 72 #define PHY_ANEG_TIMEOUT 8000 /* PHY needs a longer aneg time */ 73 74 /* PCIe support */ 75 #ifndef CONFIG_SPL_BUILD 76 #define CONFIG_PCI 77 #define CONFIG_PCI_MVEBU 78 #define CONFIG_PCI_PNP 79 #define CONFIG_PCI_SCAN_SHOW 80 #endif 81 82 #define CONFIG_SYS_ALT_MEMTEST 83 84 /* 85 * Software (bit-bang) MII driver configuration 86 */ 87 #define CONFIG_BITBANGMII /* bit-bang MII PHY management */ 88 #define CONFIG_BITBANGMII_MULTI 89 90 /* SPL */ 91 /* 92 * Select the boot device here 93 * 94 * Currently supported are: 95 * SPL_BOOT_SPI_NOR_FLASH - Booting via SPI NOR flash 96 * SPL_BOOT_SDIO_MMC_CARD - Booting via SDIO/MMC card (partition 1) 97 */ 98 #define SPL_BOOT_SPI_NOR_FLASH 1 99 #define SPL_BOOT_SDIO_MMC_CARD 2 100 #define CONFIG_SPL_BOOT_DEVICE SPL_BOOT_SPI_NOR_FLASH 101 102 /* Defines for SPL */ 103 #define CONFIG_SPL_FRAMEWORK 104 #define CONFIG_SPL_SIZE (160 << 10) 105 106 #if defined(CONFIG_SECURED_MODE_IMAGE) 107 #define CONFIG_SPL_TEXT_BASE 0x40002614 108 #define CONFIG_SPL_MAX_SIZE (CONFIG_SPL_SIZE - 0x2614) 109 #else 110 #define CONFIG_SPL_TEXT_BASE 0x40000030 111 #define CONFIG_SPL_MAX_SIZE (CONFIG_SPL_SIZE - 0x30) 112 #endif 113 114 #define CONFIG_SPL_BSS_START_ADDR (0x40000000 + CONFIG_SPL_SIZE) 115 #define CONFIG_SPL_BSS_MAX_SIZE (16 << 10) 116 117 #ifdef CONFIG_SPL_BUILD 118 #define CONFIG_SYS_MALLOC_SIMPLE 119 #endif 120 121 #define CONFIG_SPL_STACK (0x40000000 + ((212 - 16) << 10)) 122 #define CONFIG_SPL_BOOTROM_SAVE (CONFIG_SPL_STACK + 4) 123 124 #define CONFIG_SPL_LIBCOMMON_SUPPORT 125 #define CONFIG_SPL_LIBGENERIC_SUPPORT 126 #define CONFIG_SPL_SERIAL_SUPPORT 127 #define CONFIG_SPL_I2C_SUPPORT 128 129 #if CONFIG_SPL_BOOT_DEVICE == SPL_BOOT_SPI_NOR_FLASH 130 /* SPL related SPI defines */ 131 #define CONFIG_SPL_SPI_LOAD 132 #define CONFIG_SYS_SPI_U_BOOT_OFFS 0x30000 133 #define CONFIG_SYS_U_BOOT_OFFS CONFIG_SYS_SPI_U_BOOT_OFFS 134 #endif 135 136 #if CONFIG_SPL_BOOT_DEVICE == SPL_BOOT_SDIO_MMC_CARD 137 /* SPL related MMC defines */ 138 #define CONFIG_SPL_MMC_SUPPORT 139 #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION 1 140 #define CONFIG_SYS_MMC_U_BOOT_OFFS (168 << 10) 141 #define CONFIG_SYS_U_BOOT_OFFS CONFIG_SYS_MMC_U_BOOT_OFFS 142 #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR (CONFIG_SYS_U_BOOT_OFFS / 512) 143 #ifdef CONFIG_SPL_BUILD 144 #define CONFIG_FIXED_SDHCI_ALIGNED_BUFFER 0x00180000 /* in SDRAM */ 145 #endif 146 #endif 147 148 /* 149 * Environment Configuration 150 */ 151 #define CONFIG_ENV_OVERWRITE 152 153 #define CONFIG_BAUDRATE 115200 154 155 #define CONFIG_HOSTNAME ccdc 156 #define CONFIG_ROOTPATH "/opt/nfsroot" 157 #define CONFIG_BOOTFILE "ccdc.img" 158 159 #define CONFIG_PREBOOT /* enable preboot variable */ 160 161 #define CONFIG_EXTRA_ENV_SETTINGS \ 162 "netdev=eth1\0" \ 163 "consoledev=ttyS1\0" \ 164 "u-boot=u-boot.bin\0" \ 165 "bootfile_addr=1000000\0" \ 166 "keyprogram_addr=3000000\0" \ 167 "keyprogram_file=keyprogram.img\0" \ 168 "fdtfile=controlcenterdc.dtb\0" \ 169 "load=tftpboot ${loadaddr} ${u-boot}\0" \ 170 "mmcdev=0:2\0" \ 171 "update=sf probe 1:0;" \ 172 " sf erase 0 +${filesize};" \ 173 " sf write ${fileaddr} 0 ${filesize}\0" \ 174 "upd=run load update\0" \ 175 "fdt_high=0x10000000\0" \ 176 "initrd_high=0x10000000\0" \ 177 "loadkeyprogram=tpm flush_keys;" \ 178 " mmc rescan;" \ 179 " ext4load mmc ${mmcdev} ${keyprogram_addr} ${keyprogram_file};"\ 180 " source ${keyprogram_addr}:script@1\0" \ 181 "gpio1=gpio@22_25\0" \ 182 "gpio2=A29\0" \ 183 "blinkseq='0 0 0 0 2 0 2 2 3 1 3 1 0 0 2 2 3 1 3 3 2 0 2 2 3 1 1 1 " \ 184 "2 0 2 2 3 1 3 1 0 0 2 0 3 3 3 1 2 0 0 0 3 1 1 1 0 0 0 0'\0" \ 185 "bootfail=for i in ${blinkseq}; do" \ 186 " if test $i -eq 0; then" \ 187 " gpio clear ${gpio1}; gpio set ${gpio2};" \ 188 " elif test $i -eq 1; then" \ 189 " gpio clear ${gpio1}; gpio clear ${gpio2};" \ 190 " elif test $i -eq 2; then" \ 191 " gpio set ${gpio1}; gpio set ${gpio2};" \ 192 " else;" \ 193 " gpio clear ${gpio1}; gpio set ${gpio2};" \ 194 " fi; sleep 0.12; done\0" 195 196 #define CONFIG_NFSBOOTCOMMAND \ 197 "setenv bootargs root=/dev/nfs rw " \ 198 "nfsroot=${serverip}:${rootpath} " \ 199 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}:${netdev}:off " \ 200 "console=${consoledev},${baudrate} ${othbootargs}; " \ 201 "tftpboot ${bootfile_addr} ${bootfile}; " \ 202 "bootm ${bootfile_addr}" 203 204 #define CONFIG_MMCBOOTCOMMAND \ 205 "setenv bootargs root=/dev/mmcblk0p3 rw rootwait " \ 206 "console=${consoledev},${baudrate} ${othbootargs}; " \ 207 "ext2load mmc 0:2 ${bootfile_addr} ${bootfile}; " \ 208 "bootm ${bootfile_addr}" 209 210 #define CONFIG_BOOTCOMMAND \ 211 "if env exists keyprogram; then;" \ 212 " setenv keyprogram; run nfsboot;" \ 213 " fi;" \ 214 " run dobootfail" 215 216 /* 217 * mv-common.h should be defined after CMD configs since it used them 218 * to enable certain macros 219 */ 220 #include "mv-common.h" 221 222 #endif /* _CONFIG_CONTROLCENTERDC_H */ 223