1 /* 2 * Copyright (C) 2014 Stefan Roese <sr@denx.de> 3 * Copyright (C) 2016 Mario Six <mario.six@gdsys.cc> 4 * 5 * SPDX-License-Identifier: GPL-2.0+ 6 */ 7 8 #ifndef _CONFIG_CONTROLCENTERDC_H 9 #define _CONFIG_CONTROLCENTERDC_H 10 11 /* 12 * High Level Configuration Options (easy to change) 13 */ 14 #define CONFIG_CUSTOMER_BOARD_SUPPORT 15 16 #define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */ 17 #define CONFIG_DISPLAY_BOARDINFO_LATE 18 #define CONFIG_BOARD_LATE_INIT 19 #define CONFIG_LAST_STAGE_INIT 20 21 /* 22 * TEXT_BASE needs to be below 16MiB, since this area is scrubbed 23 * for DDR ECC byte filling in the SPL before loading the main 24 * U-Boot into it. 25 */ 26 #define CONFIG_SYS_TEXT_BASE 0x00800000 27 28 #define CONFIG_SYS_TCLK 250000000 /* 250MHz */ 29 30 #define CONFIG_LOADADDR 1000000 31 32 /* 33 * Commands configuration 34 */ 35 #define CONFIG_CMD_I2C 36 #define CONFIG_CMD_SPI 37 38 /* SPI NOR flash default params, used by sf commands */ 39 #define CONFIG_SF_DEFAULT_BUS 1 40 #define CONFIG_SF_DEFAULT_SPEED 1000000 41 #define CONFIG_SF_DEFAULT_MODE SPI_MODE_3 42 43 /* 44 * SDIO/MMC Card Configuration 45 */ 46 #define CONFIG_SYS_MMC_BASE MVEBU_SDIO_BASE 47 48 /* 49 * SATA/SCSI/AHCI configuration 50 */ 51 #define CONFIG_SCSI_AHCI_PLAT 52 #define CONFIG_SYS_SCSI_MAX_SCSI_ID 2 53 #define CONFIG_SYS_SCSI_MAX_LUN 1 54 #define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \ 55 CONFIG_SYS_SCSI_MAX_LUN) 56 57 /* Additional FS support/configuration */ 58 #define CONFIG_SUPPORT_VFAT 59 60 /* USB/EHCI configuration */ 61 #define CONFIG_EHCI_IS_TDI 62 63 /* Environment in SPI NOR flash */ 64 #define CONFIG_ENV_SPI_BUS 1 65 #define CONFIG_ENV_OFFSET (1 << 20) /* 1MiB in */ 66 #define CONFIG_ENV_SIZE (64 << 10) /* 64KiB */ 67 #define CONFIG_ENV_SECT_SIZE (256 << 10) /* 256KiB sectors */ 68 69 #define CONFIG_PHY_MARVELL /* there is a marvell phy */ 70 #define PHY_ANEG_TIMEOUT 8000 /* PHY needs a longer aneg time */ 71 72 /* PCIe support */ 73 #ifndef CONFIG_SPL_BUILD 74 #define CONFIG_PCI 75 #define CONFIG_PCI_MVEBU 76 #define CONFIG_PCI_PNP 77 #define CONFIG_PCI_SCAN_SHOW 78 #endif 79 80 #define CONFIG_SYS_ALT_MEMTEST 81 82 /* 83 * Software (bit-bang) MII driver configuration 84 */ 85 #define CONFIG_BITBANGMII /* bit-bang MII PHY management */ 86 #define CONFIG_BITBANGMII_MULTI 87 88 /* SPL */ 89 /* 90 * Select the boot device here 91 * 92 * Currently supported are: 93 * SPL_BOOT_SPI_NOR_FLASH - Booting via SPI NOR flash 94 * SPL_BOOT_SDIO_MMC_CARD - Booting via SDIO/MMC card (partition 1) 95 */ 96 #define SPL_BOOT_SPI_NOR_FLASH 1 97 #define SPL_BOOT_SDIO_MMC_CARD 2 98 #define CONFIG_SPL_BOOT_DEVICE SPL_BOOT_SPI_NOR_FLASH 99 100 /* Defines for SPL */ 101 #define CONFIG_SPL_FRAMEWORK 102 #define CONFIG_SPL_SIZE (160 << 10) 103 104 #if defined(CONFIG_SECURED_MODE_IMAGE) 105 #define CONFIG_SPL_TEXT_BASE 0x40002614 106 #define CONFIG_SPL_MAX_SIZE (CONFIG_SPL_SIZE - 0x2614) 107 #else 108 #define CONFIG_SPL_TEXT_BASE 0x40000030 109 #define CONFIG_SPL_MAX_SIZE (CONFIG_SPL_SIZE - 0x30) 110 #endif 111 112 #define CONFIG_SPL_BSS_START_ADDR (0x40000000 + CONFIG_SPL_SIZE) 113 #define CONFIG_SPL_BSS_MAX_SIZE (16 << 10) 114 115 #ifdef CONFIG_SPL_BUILD 116 #define CONFIG_SYS_MALLOC_SIMPLE 117 #endif 118 119 #define CONFIG_SPL_STACK (0x40000000 + ((212 - 16) << 10)) 120 #define CONFIG_SPL_BOOTROM_SAVE (CONFIG_SPL_STACK + 4) 121 122 #define CONFIG_SPL_LIBCOMMON_SUPPORT 123 #define CONFIG_SPL_LIBGENERIC_SUPPORT 124 #define CONFIG_SPL_SERIAL_SUPPORT 125 #define CONFIG_SPL_I2C_SUPPORT 126 127 #if CONFIG_SPL_BOOT_DEVICE == SPL_BOOT_SPI_NOR_FLASH 128 /* SPL related SPI defines */ 129 #define CONFIG_SPL_SPI_LOAD 130 #define CONFIG_SYS_SPI_U_BOOT_OFFS 0x30000 131 #define CONFIG_SYS_U_BOOT_OFFS CONFIG_SYS_SPI_U_BOOT_OFFS 132 #endif 133 134 #if CONFIG_SPL_BOOT_DEVICE == SPL_BOOT_SDIO_MMC_CARD 135 /* SPL related MMC defines */ 136 #define CONFIG_SPL_MMC_SUPPORT 137 #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION 1 138 #define CONFIG_SYS_MMC_U_BOOT_OFFS (168 << 10) 139 #define CONFIG_SYS_U_BOOT_OFFS CONFIG_SYS_MMC_U_BOOT_OFFS 140 #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR (CONFIG_SYS_U_BOOT_OFFS / 512) 141 #ifdef CONFIG_SPL_BUILD 142 #define CONFIG_FIXED_SDHCI_ALIGNED_BUFFER 0x00180000 /* in SDRAM */ 143 #endif 144 #endif 145 146 /* 147 * Environment Configuration 148 */ 149 #define CONFIG_ENV_OVERWRITE 150 151 #define CONFIG_BAUDRATE 115200 152 153 #define CONFIG_HOSTNAME ccdc 154 #define CONFIG_ROOTPATH "/opt/nfsroot" 155 #define CONFIG_BOOTFILE "ccdc.img" 156 157 #define CONFIG_PREBOOT /* enable preboot variable */ 158 159 #define CONFIG_EXTRA_ENV_SETTINGS \ 160 "netdev=eth1\0" \ 161 "consoledev=ttyS1\0" \ 162 "u-boot=u-boot.bin\0" \ 163 "bootfile_addr=1000000\0" \ 164 "keyprogram_addr=3000000\0" \ 165 "keyprogram_file=keyprogram.img\0" \ 166 "fdtfile=controlcenterdc.dtb\0" \ 167 "load=tftpboot ${loadaddr} ${u-boot}\0" \ 168 "mmcdev=0:2\0" \ 169 "update=sf probe 1:0;" \ 170 " sf erase 0 +${filesize};" \ 171 " sf write ${fileaddr} 0 ${filesize}\0" \ 172 "upd=run load update\0" \ 173 "fdt_high=0x10000000\0" \ 174 "initrd_high=0x10000000\0" \ 175 "loadkeyprogram=tpm flush_keys;" \ 176 " mmc rescan;" \ 177 " ext4load mmc ${mmcdev} ${keyprogram_addr} ${keyprogram_file};"\ 178 " source ${keyprogram_addr}:script@1\0" \ 179 "gpio1=gpio@22_25\0" \ 180 "gpio2=A29\0" \ 181 "blinkseq='0 0 0 0 2 0 2 2 3 1 3 1 0 0 2 2 3 1 3 3 2 0 2 2 3 1 1 1 " \ 182 "2 0 2 2 3 1 3 1 0 0 2 0 3 3 3 1 2 0 0 0 3 1 1 1 0 0 0 0'\0" \ 183 "bootfail=for i in ${blinkseq}; do" \ 184 " if test $i -eq 0; then" \ 185 " gpio clear ${gpio1}; gpio set ${gpio2};" \ 186 " elif test $i -eq 1; then" \ 187 " gpio clear ${gpio1}; gpio clear ${gpio2};" \ 188 " elif test $i -eq 2; then" \ 189 " gpio set ${gpio1}; gpio set ${gpio2};" \ 190 " else;" \ 191 " gpio clear ${gpio1}; gpio set ${gpio2};" \ 192 " fi; sleep 0.12; done\0" 193 194 #define CONFIG_NFSBOOTCOMMAND \ 195 "setenv bootargs root=/dev/nfs rw " \ 196 "nfsroot=${serverip}:${rootpath} " \ 197 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}:${netdev}:off " \ 198 "console=${consoledev},${baudrate} ${othbootargs}; " \ 199 "tftpboot ${bootfile_addr} ${bootfile}; " \ 200 "bootm ${bootfile_addr}" 201 202 #define CONFIG_MMCBOOTCOMMAND \ 203 "setenv bootargs root=/dev/mmcblk0p3 rw rootwait " \ 204 "console=${consoledev},${baudrate} ${othbootargs}; " \ 205 "ext2load mmc 0:2 ${bootfile_addr} ${bootfile}; " \ 206 "bootm ${bootfile_addr}" 207 208 #define CONFIG_BOOTCOMMAND \ 209 "if env exists keyprogram; then;" \ 210 " setenv keyprogram; run nfsboot;" \ 211 " fi;" \ 212 " run dobootfail" 213 214 /* 215 * mv-common.h should be defined after CMD configs since it used them 216 * to enable certain macros 217 */ 218 #include "mv-common.h" 219 220 #endif /* _CONFIG_CONTROLCENTERDC_H */ 221