1 /* 2 * Configuation settings for the Sentec Cobra Board. 3 * 4 * (C) Copyright 2003 Josef Baumgartner <josef.baumgartner@telex.de> 5 * 6 * See file CREDITS for list of people who contributed to this 7 * project. 8 * 9 * This program is free software; you can redistribute it and/or 10 * modify it under the terms of the GNU General Public License as 11 * published by the Free Software Foundation; either version 2 of 12 * the License, or (at your option) any later version. 13 * 14 * This program is distributed in the hope that it will be useful, 15 * but WITHOUT ANY WARRANTY; without even the implied warranty of 16 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 17 * GNU General Public License for more details. 18 * 19 * You should have received a copy of the GNU General Public License 20 * along with this program; if not, write to the Free Software 21 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, 22 * MA 02111-1307 USA 23 */ 24 25 /* --- 26 * Version: U-boot 1.0.0 - initial release for Sentec COBRA5272 board 27 * Date: 2004-03-29 28 * Author: Florian Schlote 29 * 30 * For a description of configuration options please refer also to the 31 * general u-boot-1.x.x/README file 32 * --- 33 */ 34 35 /* --- 36 * board/config.h - configuration options, board specific 37 * --- 38 */ 39 40 #ifndef _CONFIG_COBRA5272_H 41 #define _CONFIG_COBRA5272_H 42 43 /* --- 44 * Define processor 45 * possible values for Sentec board: only Coldfire M5272 processor supported 46 * (please do not change) 47 * --- 48 */ 49 50 #define CONFIG_MCF52x2 /* define processor family */ 51 #define CONFIG_M5272 /* define processor type */ 52 53 /* --- 54 * Defines processor clock - important for correct timings concerning serial 55 * interface etc. 56 * CONFIG_SYS_HZ gives unit: 1000 -> 1 Hz ^= 1000 ms 57 * --- 58 */ 59 60 #define CONFIG_SYS_HZ 1000 61 #define CONFIG_SYS_CLK 66000000 62 #define CONFIG_SYS_SDRAM_SIZE 16 /* SDRAM size in MB */ 63 64 /* --- 65 * Enable use of Ethernet 66 * --- 67 */ 68 #define CONFIG_MCFFEC 69 70 /* Enable Dma Timer */ 71 #define CONFIG_MCFTMR 72 73 /* --- 74 * Define baudrate for UART1 (console output, tftp, ...) 75 * default value of CONFIG_BAUDRATE for Sentec board: 19200 baud 76 * CONFIG_SYS_BAUDRATE_TABLE defines values that can be selected in u-boot command 77 * interface 78 * --- 79 */ 80 81 #define CONFIG_MCFUART 82 #define CONFIG_SYS_UART_PORT (0) 83 #define CONFIG_BAUDRATE 19200 84 #define CONFIG_SYS_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 } 85 86 /* --- 87 * set "#if 0" to "#if 1" if (Hardware)-WATCHDOG should be enabled & change 88 * timeout acc. to your needs 89 * #define CONFIG_WATCHDOG_TIMEOUT x , x is timeout in milliseconds, e. g. 10000 90 * for 10 sec 91 * --- 92 */ 93 94 #if 0 95 #define CONFIG_WATCHDOG 96 #define CONFIG_WATCHDOG_TIMEOUT 10000 /* timeout in milliseconds */ 97 #endif 98 99 /* --- 100 * CONFIG_MONITOR_IS_IN_RAM defines if u-boot is started from a different 101 * bootloader residing in flash ('chainloading'); if you want to use 102 * chainloading or want to compile a u-boot binary that can be loaded into 103 * RAM via BDM set 104 * "#if 0" to "#if 1" 105 * You will need a first stage bootloader then, e. g. colilo or a working BDM 106 * cable (Background Debug Mode) 107 * 108 * Setting #if 0: u-boot will start from flash and relocate itself to RAM 109 * 110 * Please do not forget to modify the setting of TEXT_BASE 111 * in board/cobra5272/config.mk accordingly (#if 0: 0xffe00000; #if 1: 0x20000) 112 * 113 * --- 114 */ 115 116 #if 0 117 #define CONFIG_MONITOR_IS_IN_RAM /* monitor is started from a preloader */ 118 #endif 119 120 /* --- 121 * Configuration for environment 122 * Environment is embedded in u-boot in the second sector of the flash 123 * --- 124 */ 125 126 #ifndef CONFIG_MONITOR_IS_IN_RAM 127 #define CONFIG_ENV_OFFSET 0x4000 128 #define CONFIG_ENV_SECT_SIZE 0x2000 129 #define CONFIG_ENV_IS_IN_FLASH 1 130 #define CONFIG_ENV_IS_EMBEDDED 1 131 #else 132 #define CONFIG_ENV_ADDR 0xffe04000 133 #define CONFIG_ENV_SECT_SIZE 0x2000 134 #define CONFIG_ENV_IS_IN_FLASH 1 135 #endif 136 137 138 /* 139 * BOOTP options 140 */ 141 #define CONFIG_BOOTP_BOOTFILESIZE 142 #define CONFIG_BOOTP_BOOTPATH 143 #define CONFIG_BOOTP_GATEWAY 144 #define CONFIG_BOOTP_HOSTNAME 145 146 147 /* 148 * Command line configuration. 149 */ 150 #include <config_cmd_default.h> 151 152 #define CONFIG_CMD_PING 153 154 #undef CONFIG_CMD_LOADS 155 #undef CONFIG_CMD_LOADB 156 #undef CONFIG_CMD_MII 157 158 #ifdef CONFIG_MCFFEC 159 # define CONFIG_NET_MULTI 1 160 # define CONFIG_MII 1 161 # define CONFIG_MII_INIT 1 162 # define CONFIG_SYS_DISCOVER_PHY 163 # define CONFIG_SYS_RX_ETH_BUFFER 8 164 # define CONFIG_SYS_FAULT_ECHO_LINK_DOWN 165 166 # define CONFIG_SYS_FEC0_PINMUX 0 167 # define CONFIG_SYS_FEC0_MIIBASE CONFIG_SYS_FEC0_IOBASE 168 # define MCFFEC_TOUT_LOOP 50000 169 /* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */ 170 # ifndef CONFIG_SYS_DISCOVER_PHY 171 # define FECDUPLEX FULL 172 # define FECSPEED _100BASET 173 # else 174 # ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN 175 # define CONFIG_SYS_FAULT_ECHO_LINK_DOWN 176 # endif 177 # endif /* CONFIG_SYS_DISCOVER_PHY */ 178 #endif 179 180 /* 181 *----------------------------------------------------------------------------- 182 * Define user parameters that have to be customized most likely 183 *----------------------------------------------------------------------------- 184 */ 185 186 /*AUTOBOOT settings - booting images automatically by u-boot after power on*/ 187 188 #define CONFIG_BOOTDELAY 5 /* used for autoboot, delay in 189 seconds u-boot will wait before starting defined (auto-)boot command, setting 190 to -1 disables delay, setting to 0 will too prevent access to u-boot command 191 interface: u-boot then has to reflashed */ 192 193 194 /* The following settings will be contained in the environment block ; if you 195 want to use a neutral environment all those settings can be manually set in 196 u-boot: 'set' command */ 197 198 #if 0 199 200 #define CONFIG_BOOTCOMMAND "bootm 0xffe80000" /*Autoboto command, please 201 enter a valid image address in flash */ 202 203 #define CONFIG_BOOTARGS " " /* default bootargs that are 204 considered during boot */ 205 206 /* User network settings */ 207 208 #define CONFIG_ETHADDR 00:00:00:00:00:09 /* default ethernet MAC addr. */ 209 #define CONFIG_IPADDR 192.168.100.2 /* default board IP address */ 210 #define CONFIG_SERVERIP 192.168.100.1 /* default tftp server IP address */ 211 212 #endif 213 214 #define CONFIG_SYS_PROMPT "COBRA > " /* Layout of u-boot prompt*/ 215 216 #define CONFIG_SYS_LOAD_ADDR 0x20000 /*Defines default RAM address 217 from which user programs will be started */ 218 219 /*---*/ 220 221 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 222 223 #if defined(CONFIG_CMD_KGDB) 224 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 225 #else 226 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 227 #endif 228 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ 229 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 230 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ 231 232 /* 233 *----------------------------------------------------------------------------- 234 * End of user parameters to be customized 235 *----------------------------------------------------------------------------- 236 */ 237 238 /* --- 239 * Defines memory range for test 240 * --- 241 */ 242 243 #define CONFIG_SYS_MEMTEST_START 0x400 244 #define CONFIG_SYS_MEMTEST_END 0x380000 245 246 /* --- 247 * Low Level Configuration Settings 248 * (address mappings, register initial values, etc.) 249 * You should know what you are doing if you make changes here. 250 * --- 251 */ 252 253 /* --- 254 * Base register address 255 * --- 256 */ 257 258 #define CONFIG_SYS_MBAR 0x10000000 /* Register Base Addrs */ 259 260 /* --- 261 * System Conf. Reg. & System Protection Reg. 262 * --- 263 */ 264 265 #define CONFIG_SYS_SCR 0x0003 266 #define CONFIG_SYS_SPR 0xffff 267 268 /* --- 269 * Ethernet settings 270 * --- 271 */ 272 273 #define CONFIG_SYS_DISCOVER_PHY 274 #define CONFIG_SYS_ENET_BD_BASE 0x780000 275 276 /*----------------------------------------------------------------------- 277 * Definitions for initial stack pointer and data area (in internal SRAM) 278 */ 279 #define CONFIG_SYS_INIT_RAM_ADDR 0x20000000 280 #define CONFIG_SYS_INIT_RAM_END 0x1000 /* End of used area in internal SRAM */ 281 #define CONFIG_SYS_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ 282 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) 283 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 284 285 /*----------------------------------------------------------------------- 286 * Start addresses for the final memory configuration 287 * (Set up by the startup code) 288 * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 289 */ 290 #define CONFIG_SYS_SDRAM_BASE 0x00000000 291 292 /* 293 *------------------------------------------------------------------------- 294 * RAM SIZE (is defined above) 295 *----------------------------------------------------------------------- 296 */ 297 298 /* #define CONFIG_SYS_SDRAM_SIZE 16 */ 299 300 /* 301 *----------------------------------------------------------------------- 302 */ 303 304 #define CONFIG_SYS_FLASH_BASE 0xffe00000 305 306 #ifdef CONFIG_MONITOR_IS_IN_RAM 307 #define CONFIG_SYS_MONITOR_BASE 0x20000 308 #else 309 #define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400) 310 #endif 311 312 #define CONFIG_SYS_MONITOR_LEN 0x20000 313 #define CONFIG_SYS_MALLOC_LEN (256 << 10) 314 #define CONFIG_SYS_BOOTPARAMS_LEN 64*1024 315 316 /* 317 * For booting Linux, the board info and command line data 318 * have to be in the first 8 MB of memory, since this is 319 * the maximum mapped by the Linux kernel during initialization ?? 320 */ 321 #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ 322 323 /*----------------------------------------------------------------------- 324 * FLASH organization 325 */ 326 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ 327 #define CONFIG_SYS_MAX_FLASH_SECT 11 /* max number of sectors on one chip */ 328 #define CONFIG_SYS_FLASH_ERASE_TOUT 1000 /* flash timeout */ 329 330 /*----------------------------------------------------------------------- 331 * Cache Configuration 332 */ 333 #define CONFIG_SYS_CACHELINE_SIZE 16 334 335 /*----------------------------------------------------------------------- 336 * Memory bank definitions 337 * 338 * Please refer also to Motorola Coldfire user manual - Chapter XXX 339 * <http://e-www.motorola.com/files/dsp/doc/ref_manual/MCF5272UM.pdf> 340 */ 341 #define CONFIG_SYS_BR0_PRELIM 0xFFE00201 342 #define CONFIG_SYS_OR0_PRELIM 0xFFE00014 343 344 #define CONFIG_SYS_BR1_PRELIM 0 345 #define CONFIG_SYS_OR1_PRELIM 0 346 347 #define CONFIG_SYS_BR2_PRELIM 0 348 #define CONFIG_SYS_OR2_PRELIM 0 349 350 #define CONFIG_SYS_BR3_PRELIM 0 351 #define CONFIG_SYS_OR3_PRELIM 0 352 353 #define CONFIG_SYS_BR4_PRELIM 0 354 #define CONFIG_SYS_OR4_PRELIM 0 355 356 #define CONFIG_SYS_BR5_PRELIM 0 357 #define CONFIG_SYS_OR5_PRELIM 0 358 359 #define CONFIG_SYS_BR6_PRELIM 0 360 #define CONFIG_SYS_OR6_PRELIM 0 361 362 #define CONFIG_SYS_BR7_PRELIM 0x00000701 363 #define CONFIG_SYS_OR7_PRELIM 0xFF00007C 364 365 /*----------------------------------------------------------------------- 366 * LED config 367 */ 368 #define LED_STAT_0 0xffff /*all LEDs off*/ 369 #define LED_STAT_1 0xfffe 370 #define LED_STAT_2 0xfffd 371 #define LED_STAT_3 0xfffb 372 #define LED_STAT_4 0xfff7 373 #define LED_STAT_5 0xffef 374 #define LED_STAT_6 0xffdf 375 #define LED_STAT_7 0xff00 /*all LEDs on*/ 376 377 /*----------------------------------------------------------------------- 378 * Port configuration (GPIO) 379 */ 380 #define CONFIG_SYS_PACNT 0x00000000 /* PortA control reg.: All pins are external 381 GPIO*/ 382 #define CONFIG_SYS_PADDR 0x00FF /* PortA direction reg.: PA7 to PA0 are outputs 383 (1^=output, 0^=input) */ 384 #define CONFIG_SYS_PADAT LED_STAT_0 /* PortA value reg.: Turn all LED off */ 385 #define CONFIG_SYS_PBCNT 0x55554155 /* PortB control reg.: Ethernet/UART 386 configuration */ 387 #define CONFIG_SYS_PBDDR 0x0000 /* PortB direction: All pins configured as inputs */ 388 #define CONFIG_SYS_PBDAT 0x0000 /* PortB value reg. */ 389 #define CONFIG_SYS_PDCNT 0x00000000 /* PortD control reg. */ 390 391 #endif /* _CONFIG_COBRA5272_H */ 392