1 /* 2 * (C) Copyright 2013 CompuLab, Ltd. 3 * Author: Igor Grinberg <grinberg@compulab.co.il> 4 * 5 * Configuration settings for the CompuLab CM-T3517 board 6 * 7 * SPDX-License-Identifier: GPL-2.0+ 8 */ 9 10 #ifndef __CONFIG_H 11 #define __CONFIG_H 12 13 /* 14 * High Level Configuration Options 15 */ 16 #define CONFIG_OMAP /* in a TI OMAP core */ 17 #define CONFIG_CM_T3517 /* working with CM-T3517 */ 18 /* Common ARM Erratas */ 19 #define CONFIG_ARM_ERRATA_454179 20 #define CONFIG_ARM_ERRATA_430973 21 #define CONFIG_ARM_ERRATA_621766 22 23 #define CONFIG_SYS_TEXT_BASE 0x80008000 24 25 /* 26 * This is needed for the DMA stuff. 27 * Although the default iss 64, we still define it 28 * to be on the safe side once the default is changed. 29 */ 30 31 #define CONFIG_EMIF4 /* The chip has EMIF4 controller */ 32 33 #include <asm/arch/cpu.h> /* get chip and board defs */ 34 #include <asm/arch/omap.h> 35 36 #define CONFIG_MACH_TYPE MACH_TYPE_CM_T3517 37 38 /* Clock Defines */ 39 #define V_OSCK 26000000 /* Clock output from T2 */ 40 #define V_SCLK (V_OSCK >> 1) 41 42 #define CONFIG_MISC_INIT_R 43 44 /* 45 * The early kernel mapping on ARM currently only maps from the base of DRAM 46 * to the end of the kernel image. The kernel is loaded at DRAM base + 0x8000. 47 * The early kernel pagetable uses DRAM base + 0x4000 to DRAM base + 0x8000, 48 * so that leaves DRAM base to DRAM base + 0x4000 available. 49 */ 50 #define CONFIG_SYS_BOOTMAPSZ 0x4000 51 52 #define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ 53 #define CONFIG_SETUP_MEMORY_TAGS 54 #define CONFIG_INITRD_TAG 55 #define CONFIG_REVISION_TAG 56 #define CONFIG_SERIAL_TAG 57 58 /* 59 * Size of malloc() pool 60 */ 61 #define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */ 62 #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 10)) 63 64 /* 65 * Hardware drivers 66 */ 67 68 /* 69 * NS16550 Configuration 70 */ 71 #define CONFIG_SYS_NS16550_SERIAL 72 #define CONFIG_SYS_NS16550_REG_SIZE (-4) 73 #define CONFIG_SYS_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */ 74 75 /* 76 * select serial console configuration 77 */ 78 #define CONFIG_CONS_INDEX 3 79 #define CONFIG_SYS_NS16550_COM3 OMAP34XX_UART3 80 #define CONFIG_SERIAL3 3 /* UART3 */ 81 82 /* allow to overwrite serial and ethaddr */ 83 #define CONFIG_ENV_OVERWRITE 84 #define CONFIG_BAUDRATE 115200 85 #define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\ 86 115200} 87 88 #define CONFIG_OMAP_GPIO 89 90 #define CONFIG_GENERIC_MMC 91 #define CONFIG_OMAP_HSMMC 92 #define CONFIG_DOS_PARTITION 93 94 /* USB */ 95 #define CONFIG_USB_MUSB_AM35X 96 97 #ifndef CONFIG_USB_MUSB_AM35X 98 #define CONFIG_USB_OMAP3 99 #define CONFIG_USB_EHCI 100 #define CONFIG_USB_EHCI_OMAP 101 #define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 146 102 #define CONFIG_OMAP_EHCI_PHY2_RESET_GPIO 147 103 #else /* !CONFIG_USB_MUSB_AM35X */ 104 #define CONFIG_USB_MUSB_PIO_ONLY 105 #endif /* CONFIG_USB_MUSB_AM35X */ 106 107 /* commands to include */ 108 #define CONFIG_CMD_MTDPARTS /* Enable MTD parts commands */ 109 #define CONFIG_MTD_DEVICE /* needed for mtdparts commands */ 110 #define CONFIG_MTD_PARTITIONS 111 #define MTDIDS_DEFAULT "nand0=nand" 112 #define MTDPARTS_DEFAULT "mtdparts=nand:512k(x-loader),"\ 113 "1920k(u-boot),256k(u-boot-env),"\ 114 "4m(kernel),-(fs)" 115 116 #define CONFIG_CMD_NAND /* NAND support */ 117 118 #define CONFIG_SYS_NO_FLASH 119 #define CONFIG_SYS_I2C 120 #define CONFIG_SYS_OMAP24_I2C_SPEED 400000 121 #define CONFIG_SYS_OMAP24_I2C_SLAVE 1 122 #define CONFIG_SYS_I2C_OMAP34XX 123 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 124 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 125 #define CONFIG_SYS_I2C_EEPROM_BUS 0 126 #define CONFIG_I2C_MULTI_BUS 127 128 /* 129 * Board NAND Info. 130 */ 131 #define CONFIG_NAND_OMAP_GPMC 132 #define CONFIG_SYS_NAND_ADDR NAND_BASE /* physical address */ 133 /* to access nand */ 134 #define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */ 135 /* to access nand at */ 136 /* CS0 */ 137 #define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */ 138 /* devices */ 139 140 /* Environment information */ 141 #define CONFIG_EXTRA_ENV_SETTINGS \ 142 "loadaddr=0x82000000\0" \ 143 "baudrate=115200\0" \ 144 "console=ttyO2,115200n8\0" \ 145 "netretry=yes\0" \ 146 "mpurate=auto\0" \ 147 "vram=12M\0" \ 148 "dvimode=1024x768MR-16@60\0" \ 149 "defaultdisplay=dvi\0" \ 150 "mmcdev=0\0" \ 151 "mmcroot=/dev/mmcblk0p2 rw rootwait\0" \ 152 "mmcrootfstype=ext4\0" \ 153 "nandroot=/dev/mtdblock4 rw\0" \ 154 "nandrootfstype=ubifs\0" \ 155 "mmcargs=setenv bootargs console=${console} " \ 156 "mpurate=${mpurate} " \ 157 "vram=${vram} " \ 158 "omapfb.mode=dvi:${dvimode} " \ 159 "omapdss.def_disp=${defaultdisplay} " \ 160 "root=${mmcroot} " \ 161 "rootfstype=${mmcrootfstype}\0" \ 162 "nandargs=setenv bootargs console=${console} " \ 163 "mpurate=${mpurate} " \ 164 "vram=${vram} " \ 165 "omapfb.mode=dvi:${dvimode} " \ 166 "omapdss.def_disp=${defaultdisplay} " \ 167 "root=${nandroot} " \ 168 "rootfstype=${nandrootfstype}\0" \ 169 "loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \ 170 "bootscript=echo Running bootscript from mmc ...; " \ 171 "source ${loadaddr}\0" \ 172 "loaduimage=fatload mmc ${mmcdev} ${loadaddr} uImage\0" \ 173 "mmcboot=echo Booting from mmc ...; " \ 174 "run mmcargs; " \ 175 "bootm ${loadaddr}\0" \ 176 "nandboot=echo Booting from nand ...; " \ 177 "run nandargs; " \ 178 "nand read ${loadaddr} 2a0000 400000; " \ 179 "bootm ${loadaddr}\0" \ 180 181 #define CONFIG_BOOTCOMMAND \ 182 "mmc dev ${mmcdev}; if mmc rescan; then " \ 183 "if run loadbootscript; then " \ 184 "run bootscript; " \ 185 "else " \ 186 "if run loaduimage; then " \ 187 "run mmcboot; " \ 188 "else run nandboot; " \ 189 "fi; " \ 190 "fi; " \ 191 "else run nandboot; fi" 192 193 /* 194 * Miscellaneous configurable options 195 */ 196 #define CONFIG_AUTO_COMPLETE 197 #define CONFIG_CMDLINE_EDITING 198 #define CONFIG_TIMESTAMP 199 #define CONFIG_SYS_AUTOLOAD "no" 200 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 201 #define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */ 202 /* Print Buffer Size */ 203 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ 204 sizeof(CONFIG_SYS_PROMPT) + 16) 205 #define CONFIG_SYS_MAXARGS 32 /* max number of command args */ 206 /* Boot Argument Buffer Size */ 207 #define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE) 208 209 #define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0 + 0x02000000) 210 211 /* 212 * AM3517 has 12 GP timers, they can be driven by the system clock 213 * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK). 214 * This rate is divided by a local divisor. 215 */ 216 #define CONFIG_SYS_TIMERBASE (OMAP34XX_GPT2) 217 #define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */ 218 #define CONFIG_SYS_HZ 1000 219 220 /*----------------------------------------------------------------------- 221 * Physical Memory Map 222 */ 223 #define CONFIG_NR_DRAM_BANKS 1 /* CM-T3517 DRAM is only on CS0 */ 224 #define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0 225 #define CONFIG_SYS_CS0_SIZE (256 << 20) 226 227 /*----------------------------------------------------------------------- 228 * FLASH and environment organization 229 */ 230 231 /* **** PISMO SUPPORT *** */ 232 /* Monitor at start of flash */ 233 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE 234 #define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */ 235 236 #define CONFIG_ENV_IS_IN_NAND 237 #define SMNAND_ENV_OFFSET 0x260000 /* environment starts here */ 238 #define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET 239 #define CONFIG_ENV_ADDR SMNAND_ENV_OFFSET 240 241 #if defined(CONFIG_CMD_NET) 242 #define CONFIG_DRIVER_TI_EMAC 243 #define CONFIG_DRIVER_TI_EMAC_USE_RMII 244 #define CONFIG_MII 245 #define CONFIG_SMC911X 246 #define CONFIG_SMC911X_32_BIT 247 #define CONFIG_SMC911X_BASE (0x2C000000 + (16 << 20)) 248 #define CONFIG_ARP_TIMEOUT 200UL 249 #define CONFIG_NET_RETRY_COUNT 5 250 #endif /* CONFIG_CMD_NET */ 251 252 /* additions for new relocation code, must be added to all boards */ 253 #define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 254 #define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800 255 #define CONFIG_SYS_INIT_RAM_SIZE 0x800 256 #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \ 257 CONFIG_SYS_INIT_RAM_SIZE - \ 258 GENERATED_GBL_DATA_SIZE) 259 260 /* Status LED */ 261 #define CONFIG_STATUS_LED /* Status LED enabled */ 262 #define CONFIG_BOARD_SPECIFIC_LED 263 #define CONFIG_GPIO_LED 264 #define GREEN_LED_GPIO 186 /* CM-T3517 Green LED is GPIO186 */ 265 #define GREEN_LED_DEV 0 266 #define STATUS_LED_BIT GREEN_LED_GPIO 267 #define STATUS_LED_STATE STATUS_LED_ON 268 #define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2) 269 #define STATUS_LED_BOOT GREEN_LED_DEV 270 271 /* GPIO banks */ 272 #ifdef CONFIG_STATUS_LED 273 #define CONFIG_OMAP3_GPIO_6 /* GPIO186 is in GPIO bank 6 */ 274 #endif 275 276 /* Display Configuration */ 277 #define CONFIG_OMAP3_GPIO_2 278 #define CONFIG_OMAP3_GPIO_5 279 #define CONFIG_VIDEO_OMAP3 280 #define LCD_BPP LCD_COLOR16 281 282 #define CONFIG_SPLASH_SCREEN 283 #define CONFIG_SPLASHIMAGE_GUARD 284 #define CONFIG_CMD_BMP 285 #define CONFIG_BMP_16BPP 286 #define CONFIG_SCF0403_LCD 287 288 #define CONFIG_OMAP3_SPI 289 290 /* EEPROM */ 291 #define CONFIG_CMD_EEPROM 292 #define CONFIG_ENV_EEPROM_IS_ON_I2C 293 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 294 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 295 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 296 #define CONFIG_SYS_EEPROM_SIZE 256 297 298 #define CONFIG_CMD_EEPROM_LAYOUT 299 #define CONFIG_EEPROM_LAYOUT_HELP_STRING "v1, v2, v3" 300 301 #endif /* __CONFIG_H */ 302