1 /* 2 * (C) Copyright 2011 CompuLab, Ltd. 3 * Mike Rapoport <mike@compulab.co.il> 4 * Igor Grinberg <grinberg@compulab.co.il> 5 * 6 * Based on omap3_beagle.h 7 * (C) Copyright 2006-2008 8 * Texas Instruments. 9 * Richard Woodruff <r-woodruff2@ti.com> 10 * Syed Mohammed Khasim <x0khasim@ti.com> 11 * 12 * Configuration settings for the CompuLab CM-T35 and CM-T3730 boards 13 * 14 * SPDX-License-Identifier: GPL-2.0+ 15 */ 16 17 #ifndef __CONFIG_H 18 #define __CONFIG_H 19 20 #define CONFIG_SYS_CACHELINE_SIZE 64 21 22 /* 23 * High Level Configuration Options 24 */ 25 #define CONFIG_CM_T3X /* working with CM-T35 and CM-T3730 */ 26 27 #include <asm/arch/cpu.h> /* get chip and board defs */ 28 #include <asm/arch/omap.h> 29 30 /* Clock Defines */ 31 #define V_OSCK 26000000 /* Clock output from T2 */ 32 #define V_SCLK (V_OSCK >> 1) 33 34 #define CONFIG_MISC_INIT_R 35 36 #define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ 37 #define CONFIG_SETUP_MEMORY_TAGS 38 #define CONFIG_INITRD_TAG 39 #define CONFIG_REVISION_TAG 40 #define CONFIG_SERIAL_TAG 41 42 /* 43 * Size of malloc() pool 44 */ 45 #define CONFIG_ENV_SIZE (16 << 10) /* 16 KiB */ 46 /* Sector */ 47 #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 10)) 48 49 /* 50 * Hardware drivers 51 */ 52 53 /* 54 * NS16550 Configuration 55 */ 56 #define V_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */ 57 58 #define CONFIG_SYS_NS16550_SERIAL 59 #define CONFIG_SYS_NS16550_REG_SIZE (-4) 60 #define CONFIG_SYS_NS16550_CLK V_NS16550_CLK 61 62 /* 63 * select serial console configuration 64 */ 65 #define CONFIG_CONS_INDEX 3 66 #define CONFIG_SYS_NS16550_COM3 OMAP34XX_UART3 67 #define CONFIG_SERIAL3 3 /* UART3 */ 68 69 /* allow to overwrite serial and ethaddr */ 70 #define CONFIG_ENV_OVERWRITE 71 #define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\ 72 115200} 73 74 /* USB */ 75 #define CONFIG_USB_OMAP3 76 #define CONFIG_USB_MUSB_UDC 77 #define CONFIG_TWL4030_USB 78 79 /* USB device configuration */ 80 #define CONFIG_USB_DEVICE 81 #define CONFIG_USB_TTY 82 83 /* commands to include */ 84 #define CONFIG_MTD_DEVICE /* needed for mtdparts commands */ 85 #define CONFIG_MTD_PARTITIONS 86 #define MTDIDS_DEFAULT "nand0=nand" 87 #define MTDPARTS_DEFAULT "mtdparts=nand:512k(x-loader),"\ 88 "1920k(u-boot),256k(u-boot-env),"\ 89 "4m(kernel),-(fs)" 90 91 #define CONFIG_SYS_I2C 92 #define CONFIG_SYS_OMAP24_I2C_SPEED 100000 93 #define CONFIG_SYS_OMAP24_I2C_SLAVE 1 94 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 95 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 96 #define CONFIG_SYS_I2C_EEPROM_BUS 0 97 #define CONFIG_I2C_MULTI_BUS 98 99 /* 100 * TWL4030 101 */ 102 #define CONFIG_TWL4030_LED 103 104 /* 105 * Board NAND Info. 106 */ 107 #define CONFIG_NAND_OMAP_GPMC 108 #define CONFIG_SYS_NAND_ADDR NAND_BASE /* physical address */ 109 /* to access nand */ 110 #define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */ 111 /* to access nand at */ 112 /* CS0 */ 113 #define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */ 114 /* devices */ 115 116 /* Environment information */ 117 #define CONFIG_EXTRA_ENV_SETTINGS \ 118 "loadaddr=0x82000000\0" \ 119 "usbtty=cdc_acm\0" \ 120 "console=ttyO2,115200n8\0" \ 121 "mpurate=500\0" \ 122 "vram=12M\0" \ 123 "dvimode=1024x768MR-16@60\0" \ 124 "defaultdisplay=dvi\0" \ 125 "mmcdev=0\0" \ 126 "mmcroot=/dev/mmcblk0p2 rw\0" \ 127 "mmcrootfstype=ext4 rootwait\0" \ 128 "nandroot=/dev/mtdblock4 rw\0" \ 129 "nandrootfstype=ubifs\0" \ 130 "mmcargs=setenv bootargs console=${console} " \ 131 "mpurate=${mpurate} " \ 132 "vram=${vram} " \ 133 "omapfb.mode=dvi:${dvimode} " \ 134 "omapdss.def_disp=${defaultdisplay} " \ 135 "root=${mmcroot} " \ 136 "rootfstype=${mmcrootfstype}\0" \ 137 "nandargs=setenv bootargs console=${console} " \ 138 "mpurate=${mpurate} " \ 139 "vram=${vram} " \ 140 "omapfb.mode=dvi:${dvimode} " \ 141 "omapdss.def_disp=${defaultdisplay} " \ 142 "root=${nandroot} " \ 143 "rootfstype=${nandrootfstype}\0" \ 144 "loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \ 145 "bootscript=echo Running bootscript from mmc ...; " \ 146 "source ${loadaddr}\0" \ 147 "loaduimage=fatload mmc ${mmcdev} ${loadaddr} uImage\0" \ 148 "mmcboot=echo Booting from mmc ...; " \ 149 "run mmcargs; " \ 150 "bootm ${loadaddr}\0" \ 151 "nandboot=echo Booting from nand ...; " \ 152 "run nandargs; " \ 153 "nand read ${loadaddr} 2a0000 400000; " \ 154 "bootm ${loadaddr}\0" \ 155 156 #define CONFIG_BOOTCOMMAND \ 157 "mmc dev ${mmcdev}; if mmc rescan; then " \ 158 "if run loadbootscript; then " \ 159 "run bootscript; " \ 160 "else " \ 161 "if run loaduimage; then " \ 162 "run mmcboot; " \ 163 "else run nandboot; " \ 164 "fi; " \ 165 "fi; " \ 166 "else run nandboot; fi" 167 168 /* 169 * Miscellaneous configurable options 170 */ 171 #define CONFIG_AUTO_COMPLETE 172 #define CONFIG_CMDLINE_EDITING 173 #define CONFIG_TIMESTAMP 174 #define CONFIG_SYS_AUTOLOAD "no" 175 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 176 177 #define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0) /* memtest */ 178 /* works on */ 179 #define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + \ 180 0x01F00000) /* 31MB */ 181 182 #define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0) /* default */ 183 /* load address */ 184 185 /* 186 * OMAP3 has 12 GP timers, they can be driven by the system clock 187 * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK). 188 * This rate is divided by a local divisor. 189 */ 190 #define CONFIG_SYS_TIMERBASE (OMAP34XX_GPT2) 191 #define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */ 192 193 /*----------------------------------------------------------------------- 194 * Physical Memory Map 195 */ 196 #define CONFIG_NR_DRAM_BANKS 1 /* CS1 is never populated */ 197 #define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0 198 199 /*----------------------------------------------------------------------- 200 * FLASH and environment organization 201 */ 202 203 /* **** PISMO SUPPORT *** */ 204 /* Monitor at start of flash */ 205 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE 206 #define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */ 207 208 #define CONFIG_ENV_OFFSET 0x260000 209 #define CONFIG_ENV_ADDR 0x260000 210 211 #if defined(CONFIG_CMD_NET) 212 #define CONFIG_SMC911X 213 #define CONFIG_SMC911X_32_BIT 214 #define CM_T3X_SMC911X_BASE 0x2C000000 215 #define SB_T35_SMC911X_BASE (CM_T3X_SMC911X_BASE + (16 << 20)) 216 #define CONFIG_SMC911X_BASE CM_T3X_SMC911X_BASE 217 #endif /* (CONFIG_CMD_NET) */ 218 219 /* additions for new relocation code, must be added to all boards */ 220 #define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 221 #define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800 222 #define CONFIG_SYS_INIT_RAM_SIZE 0x800 223 #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \ 224 CONFIG_SYS_INIT_RAM_SIZE - \ 225 GENERATED_GBL_DATA_SIZE) 226 227 /* Status LED */ 228 #define GREEN_LED_GPIO 186 /* CM-T35 Green LED is GPIO186 */ 229 230 #define CONFIG_SPLASHIMAGE_GUARD 231 232 /* Display Configuration */ 233 #define CONFIG_VIDEO_OMAP3 234 #define LCD_BPP LCD_COLOR16 235 236 #define CONFIG_SPLASH_SCREEN 237 #define CONFIG_SPLASH_SOURCE 238 #define CONFIG_BMP_16BPP 239 #define CONFIG_SCF0403_LCD 240 241 /* Defines for SPL */ 242 #define CONFIG_SPL_FRAMEWORK 243 #define CONFIG_SPL_NAND_SIMPLE 244 245 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1 246 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img" 247 248 #define CONFIG_SPL_NAND_BASE 249 #define CONFIG_SPL_NAND_DRIVERS 250 #define CONFIG_SPL_NAND_ECC 251 252 /* NAND boot config */ 253 #define CONFIG_SYS_NAND_5_ADDR_CYCLE 254 #define CONFIG_SYS_NAND_PAGE_COUNT 64 255 #define CONFIG_SYS_NAND_PAGE_SIZE 2048 256 #define CONFIG_SYS_NAND_OOBSIZE 64 257 #define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) 258 #define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS 259 /* 260 * Use the ECC/OOB layout from omap_gpmc.h that matches your chip: 261 * SP vs LP, 8bit vs 16bit: GPMC_NAND_HW_ECC_LAYOUT 262 */ 263 #define CONFIG_SYS_NAND_ECCPOS { 1, 2, 3, 4, 5, 6, 7, 8, 9, \ 264 10, 11, 12 } 265 #define CONFIG_SYS_NAND_ECCSIZE 512 266 #define CONFIG_SYS_NAND_ECCBYTES 3 267 #define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_HW 268 269 #define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE 270 #define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000 271 272 #define CONFIG_SPL_TEXT_BASE 0x40200800 273 #define CONFIG_SPL_MAX_SIZE (SRAM_SCRATCH_SPACE_ADDR - \ 274 CONFIG_SPL_TEXT_BASE) 275 276 /* 277 * Use 0x80008000 as TEXT_BASE here for compatibility reasons with the 278 * older x-loader implementations. And move the BSS area so that it 279 * doesn't overlap with TEXT_BASE. 280 */ 281 #define CONFIG_SYS_TEXT_BASE 0x80008000 282 #define CONFIG_SPL_BSS_START_ADDR 0x80100000 283 #define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */ 284 285 #define CONFIG_SYS_SPL_MALLOC_START 0x80208000 286 #define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000 287 288 /* EEPROM */ 289 #define CONFIG_ENV_EEPROM_IS_ON_I2C 290 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 291 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 292 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 293 #define CONFIG_SYS_EEPROM_SIZE 256 294 295 #endif /* __CONFIG_H */ 296