1 /* 2 * (C) Copyright 2011 CompuLab, Ltd. 3 * Mike Rapoport <mike@compulab.co.il> 4 * Igor Grinberg <grinberg@compulab.co.il> 5 * 6 * Based on omap3_beagle.h 7 * (C) Copyright 2006-2008 8 * Texas Instruments. 9 * Richard Woodruff <r-woodruff2@ti.com> 10 * Syed Mohammed Khasim <x0khasim@ti.com> 11 * 12 * Configuration settings for the CompuLab CM-T35 and CM-T3730 boards 13 * 14 * SPDX-License-Identifier: GPL-2.0+ 15 */ 16 17 #ifndef __CONFIG_H 18 #define __CONFIG_H 19 20 /* 21 * High Level Configuration Options 22 */ 23 #define CONFIG_OMAP /* in a TI OMAP core */ 24 #define CONFIG_OMAP34XX /* which is a 34XX */ 25 #define CONFIG_OMAP_GPIO 26 #define CONFIG_CM_T3X /* working with CM-T35 and CM-T3730 */ 27 28 #define CONFIG_SYS_TEXT_BASE 0x80008000 29 30 #define CONFIG_SDRC /* The chip has SDRC controller */ 31 32 #include <asm/arch/cpu.h> /* get chip and board defs */ 33 #include <asm/arch/omap3.h> 34 35 /* 36 * Display CPU and Board information 37 */ 38 #define CONFIG_DISPLAY_CPUINFO 39 #define CONFIG_DISPLAY_BOARDINFO 40 41 /* Clock Defines */ 42 #define V_OSCK 26000000 /* Clock output from T2 */ 43 #define V_SCLK (V_OSCK >> 1) 44 45 #define CONFIG_MISC_INIT_R 46 47 #define CONFIG_OF_LIBFDT 1 48 /* 49 * The early kernel mapping on ARM currently only maps from the base of DRAM 50 * to the end of the kernel image. The kernel is loaded at DRAM base + 0x8000. 51 * The early kernel pagetable uses DRAM base + 0x4000 to DRAM base + 0x8000, 52 * so that leaves DRAM base to DRAM base + 0x4000 available. 53 */ 54 #define CONFIG_SYS_BOOTMAPSZ 0x4000 55 56 #define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ 57 #define CONFIG_SETUP_MEMORY_TAGS 58 #define CONFIG_INITRD_TAG 59 #define CONFIG_REVISION_TAG 60 #define CONFIG_SERIAL_TAG 61 62 /* 63 * Size of malloc() pool 64 */ 65 #define CONFIG_ENV_SIZE (16 << 10) /* 16 KiB */ 66 /* Sector */ 67 #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 10)) 68 69 /* 70 * Hardware drivers 71 */ 72 73 /* 74 * NS16550 Configuration 75 */ 76 #define V_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */ 77 78 #define CONFIG_SYS_NS16550 79 #define CONFIG_SYS_NS16550_SERIAL 80 #define CONFIG_SYS_NS16550_REG_SIZE (-4) 81 #define CONFIG_SYS_NS16550_CLK V_NS16550_CLK 82 83 /* 84 * select serial console configuration 85 */ 86 #define CONFIG_CONS_INDEX 3 87 #define CONFIG_SYS_NS16550_COM3 OMAP34XX_UART3 88 #define CONFIG_SERIAL3 3 /* UART3 */ 89 90 /* allow to overwrite serial and ethaddr */ 91 #define CONFIG_ENV_OVERWRITE 92 #define CONFIG_BAUDRATE 115200 93 #define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\ 94 115200} 95 96 #define CONFIG_GENERIC_MMC 97 #define CONFIG_MMC 98 #define CONFIG_OMAP_HSMMC 99 #define CONFIG_DOS_PARTITION 100 101 /* USB */ 102 #define CONFIG_USB_OMAP3 103 #define CONFIG_USB_EHCI 104 #define CONFIG_USB_EHCI_OMAP 105 #define CONFIG_USB_ULPI 106 #define CONFIG_USB_ULPI_VIEWPORT_OMAP 107 #define CONFIG_USB_STORAGE 108 #define CONFIG_MUSB_UDC 109 #define CONFIG_TWL4030_USB 110 #define CONFIG_CMD_USB 111 112 /* USB device configuration */ 113 #define CONFIG_USB_DEVICE 114 #define CONFIG_USB_TTY 115 #define CONFIG_SYS_CONSOLE_IS_IN_ENV 116 117 /* commands to include */ 118 #include <config_cmd_default.h> 119 120 #define CONFIG_CMD_CACHE 121 #define CONFIG_CMD_EXT2 /* EXT2 Support */ 122 #define CONFIG_CMD_FAT /* FAT support */ 123 #define CONFIG_CMD_MTDPARTS /* Enable MTD parts commands */ 124 #define CONFIG_MTD_DEVICE /* needed for mtdparts commands */ 125 #define CONFIG_MTD_PARTITIONS 126 #define MTDIDS_DEFAULT "nand0=nand" 127 #define MTDPARTS_DEFAULT "mtdparts=nand:512k(x-loader),"\ 128 "1920k(u-boot),256k(u-boot-env),"\ 129 "4m(kernel),-(fs)" 130 131 #define CONFIG_CMD_I2C /* I2C serial bus support */ 132 #define CONFIG_CMD_MMC /* MMC support */ 133 #define CONFIG_CMD_NAND /* NAND support */ 134 #define CONFIG_CMD_DHCP 135 #define CONFIG_CMD_PING 136 137 #undef CONFIG_CMD_FLASH /* flinfo, erase, protect */ 138 #undef CONFIG_CMD_FPGA /* FPGA configuration Support */ 139 #undef CONFIG_CMD_IMLS /* List all found images */ 140 141 #define CONFIG_SYS_NO_FLASH 142 #define CONFIG_HARD_I2C 143 #define CONFIG_SYS_I2C_SPEED 100000 144 #define CONFIG_SYS_I2C_SLAVE 1 145 #define CONFIG_DRIVER_OMAP34XX_I2C 146 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 147 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 148 #define CONFIG_I2C_MULTI_BUS 149 150 /* 151 * TWL4030 152 */ 153 #define CONFIG_TWL4030_POWER 154 #define CONFIG_TWL4030_LED 155 156 /* 157 * Board NAND Info. 158 */ 159 #define CONFIG_SYS_NAND_QUIET_TEST 160 #define CONFIG_NAND_OMAP_GPMC 161 #define CONFIG_SYS_NAND_ADDR NAND_BASE /* physical address */ 162 /* to access nand */ 163 #define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */ 164 /* to access nand at */ 165 /* CS0 */ 166 #define GPMC_NAND_ECC_LP_x8_LAYOUT 167 168 #define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */ 169 /* devices */ 170 /* Environment information */ 171 #define CONFIG_BOOTDELAY 10 172 #define CONFIG_ZERO_BOOTDELAY_CHECK 173 174 #define CONFIG_EXTRA_ENV_SETTINGS \ 175 "loadaddr=0x82000000\0" \ 176 "usbtty=cdc_acm\0" \ 177 "console=ttyS2,115200n8\0" \ 178 "mpurate=500\0" \ 179 "vram=12M\0" \ 180 "dvimode=1024x768MR-16@60\0" \ 181 "defaultdisplay=dvi\0" \ 182 "mmcdev=0\0" \ 183 "mmcroot=/dev/mmcblk0p2 rw\0" \ 184 "mmcrootfstype=ext4 rootwait\0" \ 185 "nandroot=/dev/mtdblock4 rw\0" \ 186 "nandrootfstype=ubifs\0" \ 187 "mmcargs=setenv bootargs console=${console} " \ 188 "mpurate=${mpurate} " \ 189 "vram=${vram} " \ 190 "omapfb.mode=dvi:${dvimode} " \ 191 "omapfb.debug=y " \ 192 "omapdss.def_disp=${defaultdisplay} " \ 193 "root=${mmcroot} " \ 194 "rootfstype=${mmcrootfstype}\0" \ 195 "nandargs=setenv bootargs console=${console} " \ 196 "mpurate=${mpurate} " \ 197 "vram=${vram} " \ 198 "omapfb.mode=dvi:${dvimode} " \ 199 "omapfb.debug=y " \ 200 "omapdss.def_disp=${defaultdisplay} " \ 201 "root=${nandroot} " \ 202 "rootfstype=${nandrootfstype}\0" \ 203 "loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \ 204 "bootscript=echo Running bootscript from mmc ...; " \ 205 "source ${loadaddr}\0" \ 206 "loaduimage=fatload mmc ${mmcdev} ${loadaddr} uImage\0" \ 207 "mmcboot=echo Booting from mmc ...; " \ 208 "run mmcargs; " \ 209 "bootm ${loadaddr}\0" \ 210 "nandboot=echo Booting from nand ...; " \ 211 "run nandargs; " \ 212 "nand read ${loadaddr} 2a0000 400000; " \ 213 "bootm ${loadaddr}\0" \ 214 215 #define CONFIG_BOOTCOMMAND \ 216 "mmc dev ${mmcdev}; if mmc rescan; then " \ 217 "if run loadbootscript; then " \ 218 "run bootscript; " \ 219 "else " \ 220 "if run loaduimage; then " \ 221 "run mmcboot; " \ 222 "else run nandboot; " \ 223 "fi; " \ 224 "fi; " \ 225 "else run nandboot; fi" 226 227 /* 228 * Miscellaneous configurable options 229 */ 230 #define CONFIG_AUTO_COMPLETE 231 #define CONFIG_CMDLINE_EDITING 232 #define CONFIG_TIMESTAMP 233 #define CONFIG_SYS_AUTOLOAD "no" 234 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 235 #define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ 236 #define CONFIG_SYS_PROMPT "CM-T3x # " 237 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 238 /* Print Buffer Size */ 239 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ 240 sizeof(CONFIG_SYS_PROMPT) + 16) 241 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 242 /* Boot Argument Buffer Size */ 243 #define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE) 244 245 #define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0) /* memtest */ 246 /* works on */ 247 #define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + \ 248 0x01F00000) /* 31MB */ 249 250 #define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0) /* default */ 251 /* load address */ 252 253 /* 254 * OMAP3 has 12 GP timers, they can be driven by the system clock 255 * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK). 256 * This rate is divided by a local divisor. 257 */ 258 #define CONFIG_SYS_TIMERBASE (OMAP34XX_GPT2) 259 #define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */ 260 #define CONFIG_SYS_HZ 1000 261 262 /*----------------------------------------------------------------------- 263 * Physical Memory Map 264 */ 265 #define CONFIG_NR_DRAM_BANKS 1 /* CS1 is never populated */ 266 #define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0 267 268 /*----------------------------------------------------------------------- 269 * FLASH and environment organization 270 */ 271 272 /* **** PISMO SUPPORT *** */ 273 /* Configure the PISMO */ 274 #define PISMO1_NAND_SIZE GPMC_SIZE_128M 275 276 /* Monitor at start of flash */ 277 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE 278 #define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */ 279 280 #define CONFIG_ENV_IS_IN_NAND 281 #define SMNAND_ENV_OFFSET 0x260000 /* environment starts here */ 282 #define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET 283 #define CONFIG_ENV_ADDR SMNAND_ENV_OFFSET 284 285 #if defined(CONFIG_CMD_NET) 286 #define CONFIG_SMC911X 287 #define CONFIG_SMC911X_32_BIT 288 #define CM_T3X_SMC911X_BASE 0x2C000000 289 #define SB_T35_SMC911X_BASE (CM_T3X_SMC911X_BASE + (16 << 20)) 290 #define CONFIG_SMC911X_BASE CM_T3X_SMC911X_BASE 291 #endif /* (CONFIG_CMD_NET) */ 292 293 /* additions for new relocation code, must be added to all boards */ 294 #define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 295 #define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800 296 #define CONFIG_SYS_INIT_RAM_SIZE 0x800 297 #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \ 298 CONFIG_SYS_INIT_RAM_SIZE - \ 299 GENERATED_GBL_DATA_SIZE) 300 301 /* Status LED */ 302 #define CONFIG_STATUS_LED /* Status LED enabled */ 303 #define CONFIG_BOARD_SPECIFIC_LED 304 #define STATUS_LED_GREEN 0 305 #define STATUS_LED_BIT STATUS_LED_GREEN 306 #define STATUS_LED_STATE STATUS_LED_ON 307 #define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2) 308 #define STATUS_LED_BOOT STATUS_LED_BIT 309 #define GREEN_LED_GPIO 186 /* CM-T35 Green LED is GPIO186 */ 310 311 #define CONFIG_SPLASHIMAGE_GUARD 312 313 /* GPIO banks */ 314 #ifdef CONFIG_STATUS_LED 315 #define CONFIG_OMAP3_GPIO_6 /* GPIO186 is in GPIO bank 6 */ 316 #endif 317 318 /* Display Configuration */ 319 #define CONFIG_OMAP3_GPIO_2 320 #define CONFIG_VIDEO_OMAP3 321 #define LCD_BPP LCD_COLOR16 322 323 #define CONFIG_LCD 324 #define CONFIG_SPLASH_SCREEN 325 #define CONFIG_CMD_BMP 326 #define CONFIG_BMP_16BPP 327 328 #endif /* __CONFIG_H */ 329