1 /* 2 * Config file for Compulab CM-FX6 board 3 * 4 * Copyright (C) 2014, Compulab Ltd - http://compulab.co.il/ 5 * 6 * Author: Nikita Kiryanov <nikita@compulab.co.il> 7 * 8 * SPDX-License-Identifier: GPL-2.0+ 9 */ 10 11 #ifndef __CONFIG_CM_FX6_H 12 #define __CONFIG_CM_FX6_H 13 14 #include "mx6_common.h" 15 16 /* Machine config */ 17 #define CONFIG_SYS_LITTLE_ENDIAN 18 #define CONFIG_MACH_TYPE 4273 19 20 /* CMD */ 21 22 /* MMC */ 23 #define CONFIG_SYS_FSL_USDHC_NUM 3 24 #define CONFIG_SYS_FSL_ESDHC_ADDR USDHC2_BASE_ADDR 25 26 /* RAM */ 27 #define PHYS_SDRAM_1 MMDC0_ARB_BASE_ADDR 28 #define PHYS_SDRAM_2 MMDC1_ARB_BASE_ADDR 29 #define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 30 #define CONFIG_NR_DRAM_BANKS 2 31 #define CONFIG_SYS_MEMTEST_START 0x10000000 32 #define CONFIG_SYS_MEMTEST_END 0x10010000 33 #define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR 34 #define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE 35 #define CONFIG_SYS_INIT_SP_OFFSET \ 36 (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 37 #define CONFIG_SYS_INIT_SP_ADDR \ 38 (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) 39 40 /* Serial console */ 41 #define CONFIG_MXC_UART 42 #define CONFIG_MXC_UART_BASE UART4_BASE 43 #define CONFIG_BAUDRATE 115200 44 #define CONFIG_SYS_BAUDRATE_TABLE {9600, 19200, 38400, 57600, 115200} 45 46 /* Shell */ 47 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ 48 sizeof(CONFIG_SYS_PROMPT) + 16) 49 50 /* SPI flash */ 51 #define CONFIG_SF_DEFAULT_BUS 0 52 #define CONFIG_SF_DEFAULT_CS 0 53 #define CONFIG_SF_DEFAULT_SPEED 25000000 54 #define CONFIG_SF_DEFAULT_MODE (SPI_MODE_0) 55 56 /* Environment */ 57 #define CONFIG_ENV_IS_IN_SPI_FLASH 58 #define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED 59 #define CONFIG_ENV_SPI_MODE CONFIG_SF_DEFAULT_MODE 60 #define CONFIG_ENV_SPI_BUS CONFIG_SF_DEFAULT_BUS 61 #define CONFIG_ENV_SPI_CS CONFIG_SF_DEFAULT_CS 62 #define CONFIG_ENV_SECT_SIZE (64 * 1024) 63 #define CONFIG_ENV_SIZE (8 * 1024) 64 #define CONFIG_ENV_OFFSET (768 * 1024) 65 66 #define CONFIG_EXTRA_ENV_SETTINGS \ 67 "stdin=serial,usbkbd\0" \ 68 "stdout=serial,vga\0" \ 69 "stderr=serial,vga\0" \ 70 "panel=HDMI\0" \ 71 "autoload=no\0" \ 72 "kernel=uImage-cm-fx6\0" \ 73 "script=boot.scr\0" \ 74 "dtb=cm-fx6.dtb\0" \ 75 "bootm_low=18000000\0" \ 76 "loadaddr=0x10800000\0" \ 77 "fdtaddr=0x11000000\0" \ 78 "console=ttymxc3,115200\0" \ 79 "ethprime=FEC0\0" \ 80 "video_hdmi=mxcfb0:dev=hdmi,1920x1080M-32@50,if=RGB32\0" \ 81 "video_dvi=mxcfb0:dev=dvi,1280x800M-32@50,if=RGB32\0" \ 82 "doboot=bootm ${loadaddr}\0" \ 83 "doloadfdt=false\0" \ 84 "setboottypez=setenv kernel zImage-cm-fx6;" \ 85 "setenv doboot bootz ${loadaddr} - ${fdtaddr};" \ 86 "setenv doloadfdt true;\0" \ 87 "setboottypem=setenv kernel uImage-cm-fx6;" \ 88 "setenv doboot bootm ${loadaddr};" \ 89 "setenv doloadfdt false;\0"\ 90 "mmcroot=/dev/mmcblk0p2 rw rootwait\0" \ 91 "sataroot=/dev/sda2 rw rootwait\0" \ 92 "nandroot=/dev/mtdblock4 rw\0" \ 93 "nandrootfstype=ubifs\0" \ 94 "mmcargs=setenv bootargs console=${console} root=${mmcroot} " \ 95 "${video}\0" \ 96 "sataargs=setenv bootargs console=${console} root=${sataroot} " \ 97 "${video}\0" \ 98 "nandargs=setenv bootargs console=${console} " \ 99 "root=${nandroot} " \ 100 "rootfstype=${nandrootfstype} " \ 101 "${video}\0" \ 102 "nandboot=if run nandloadkernel; then " \ 103 "run nandloadfdt;" \ 104 "run setboottypem;" \ 105 "run storagebootcmd;" \ 106 "run setboottypez;" \ 107 "run storagebootcmd;" \ 108 "fi;\0" \ 109 "run_eboot=echo Starting EBOOT ...; "\ 110 "mmc dev 2 && " \ 111 "mmc rescan && mmc read 10042000 a 400 && go 10042000\0" \ 112 "loadscript=load ${storagetype} ${storagedev} ${loadaddr} ${script};\0"\ 113 "loadkernel=load ${storagetype} ${storagedev} ${loadaddr} ${kernel};\0"\ 114 "loadfdt=load ${storagetype} ${storagedev} ${fdtaddr} ${dtb};\0" \ 115 "bootscript=echo Running bootscript from ${storagetype} ...;" \ 116 "source ${loadaddr};\0" \ 117 "nandloadkernel=nand read ${loadaddr} 0 780000;\0" \ 118 "nandloadfdt=nand read ${fdtaddr} 780000 80000;\0" \ 119 "setupmmcboot=setenv storagetype mmc; setenv storagedev 2;\0" \ 120 "setupsataboot=setenv storagetype sata; setenv storagedev 0;\0" \ 121 "setupnandboot=setenv storagetype nand;\0" \ 122 "setupusbboot=setenv storagetype usb; setenv storagedev 0;\0" \ 123 "storagebootcmd=echo Booting from ${storagetype} ...;" \ 124 "run ${storagetype}args; run doboot;\0" \ 125 "trybootk=if run loadkernel; then " \ 126 "if ${doloadfdt}; then " \ 127 "run loadfdt;" \ 128 "fi;" \ 129 "run storagebootcmd;" \ 130 "fi;\0" \ 131 "trybootsmz=if run loadscript; then " \ 132 "run bootscript;" \ 133 "fi;" \ 134 "run setboottypem;" \ 135 "run trybootk;" \ 136 "run setboottypez;" \ 137 "run trybootk;\0" 138 139 #define CONFIG_BOOTCOMMAND \ 140 "run setupmmcboot;" \ 141 "mmc dev ${storagedev};" \ 142 "if mmc rescan; then " \ 143 "run trybootsmz;" \ 144 "fi;" \ 145 "run setupusbboot;" \ 146 "if usb start; then "\ 147 "if run loadscript; then " \ 148 "run bootscript;" \ 149 "fi;" \ 150 "fi;" \ 151 "run setupsataboot;" \ 152 "if sata init; then " \ 153 "run trybootsmz;" \ 154 "fi;" \ 155 "run setupnandboot;" \ 156 "run nandboot;" 157 158 #define CONFIG_PREBOOT "usb start" 159 160 /* SPI */ 161 #define CONFIG_SPI 162 #define CONFIG_MXC_SPI 163 164 /* NAND */ 165 #ifndef CONFIG_SPL_BUILD 166 #define CONFIG_CMD_NAND 167 #define CONFIG_SYS_NAND_BASE 0x40000000 168 #define CONFIG_SYS_NAND_MAX_CHIPS 1 169 #define CONFIG_SYS_MAX_NAND_DEVICE 1 170 #define CONFIG_NAND_MXS 171 #define CONFIG_SYS_NAND_ONFI_DETECTION 172 /* APBH DMA is required for NAND support */ 173 #define CONFIG_APBH_DMA 174 #define CONFIG_APBH_DMA_BURST 175 #define CONFIG_APBH_DMA_BURST8 176 #endif 177 178 /* Ethernet */ 179 #define CONFIG_FEC_MXC 180 #define CONFIG_FEC_MXC_PHYADDR 0 181 #define CONFIG_FEC_XCV_TYPE RGMII 182 #define IMX_FEC_BASE ENET_BASE_ADDR 183 #define CONFIG_PHYLIB 184 #define CONFIG_PHY_ATHEROS 185 #define CONFIG_MII 186 #define CONFIG_ETHPRIME "FEC0" 187 #define CONFIG_ARP_TIMEOUT 200UL 188 #define CONFIG_NET_RETRY_COUNT 5 189 190 /* USB */ 191 #define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW) 192 #define CONFIG_MXC_USB_FLAGS 0 193 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2 194 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET /* For OTG port */ 195 #define CONFIG_SYS_STDIO_DEREGISTER 196 197 /* I2C */ 198 #define CONFIG_SYS_I2C 199 #define CONFIG_SYS_I2C_MXC 200 #define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */ 201 #define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */ 202 #define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */ 203 #define CONFIG_SYS_I2C_SPEED 100000 204 #define CONFIG_SYS_MXC_I2C3_SPEED 400000 205 206 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 207 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 208 #define CONFIG_SYS_I2C_EEPROM_BUS 2 209 210 /* SATA */ 211 #define CONFIG_CMD_SATA 212 #define CONFIG_SYS_SATA_MAX_DEVICE 1 213 #define CONFIG_LIBATA 214 #define CONFIG_LBA48 215 #define CONFIG_DWC_AHSATA 216 #define CONFIG_DWC_AHSATA_PORT_ID 0 217 #define CONFIG_DWC_AHSATA_BASE_ADDR SATA_ARB_BASE_ADDR 218 219 /* Boot */ 220 #define CONFIG_SYS_BOOTMAPSZ (8 << 20) 221 #define CONFIG_SERIAL_TAG 222 223 /* misc */ 224 #define CONFIG_STACKSIZE (128 * 1024) 225 #define CONFIG_SYS_MALLOC_LEN (10 * 1024 * 1024) 226 #define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 800 /* 400 KB */ 227 #define CONFIG_MISC_INIT_R 228 229 /* SPL */ 230 #include "imx6_spl.h" 231 #define CONFIG_SPL_MMC_SUPPORT 232 #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x80 /* offset 64 kb */ 233 #define CONFIG_SYS_MONITOR_LEN (CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS / 2 * 1024) 234 #define CONFIG_SPL_SPI_SUPPORT 235 #define CONFIG_SPL_SPI_FLASH_SUPPORT 236 #define CONFIG_SYS_SPI_U_BOOT_OFFS (64 * 1024) 237 #define CONFIG_SPL_SPI_LOAD 238 239 /* Display */ 240 #define CONFIG_VIDEO 241 #define CONFIG_VIDEO_IPUV3 242 #define CONFIG_IPUV3_CLK 260000000 243 #define CONFIG_IMX_HDMI 244 #define CONFIG_CFB_CONSOLE 245 #define CONFIG_VGA_AS_SINGLE_DEVICE 246 #define CONFIG_SYS_CONSOLE_IS_IN_ENV 247 #define CONFIG_CONSOLE_MUX 248 #define CONFIG_VIDEO_SW_CURSOR 249 250 #define CONFIG_SPLASH_SCREEN 251 #define CONFIG_SPLASH_SOURCE 252 #define CONFIG_CMD_BMP 253 #define CONFIG_VIDEO_BMP_RLE8 254 255 #define CONFIG_VIDEO_LOGO 256 #define CONFIG_VIDEO_BMP_LOGO 257 258 /* EEPROM */ 259 #define CONFIG_CMD_EEPROM 260 #define CONFIG_ENV_EEPROM_IS_ON_I2C 261 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 262 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 263 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 264 #define CONFIG_SYS_EEPROM_SIZE 256 265 266 #define CONFIG_CMD_EEPROM_LAYOUT 267 #define CONFIG_EEPROM_LAYOUT_HELP_STRING "v2, v3" 268 269 #endif /* __CONFIG_CM_FX6_H */ 270