1 /* 2 * Copyright (C) 2015 Stefan Roese <sr@denx.de> 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 #ifndef _CONFIG_CLEARFOG_H 8 #define _CONFIG_CLEARFOG_H 9 10 /* 11 * High Level Configuration Options (easy to change) 12 */ 13 14 #define CONFIG_DISPLAY_BOARDINFO_LATE 15 16 /* 17 * TEXT_BASE needs to be below 16MiB, since this area is scrubbed 18 * for DDR ECC byte filling in the SPL before loading the main 19 * U-Boot into it. 20 */ 21 #define CONFIG_SYS_TEXT_BASE 0x00800000 22 #define CONFIG_SYS_TCLK 250000000 /* 250MHz */ 23 24 /* 25 * Commands configuration 26 */ 27 #define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */ 28 #define CONFIG_CMD_ENV 29 #define CONFIG_CMD_PCI 30 31 /* I2C */ 32 #define CONFIG_SYS_I2C 33 #define CONFIG_SYS_I2C_MVTWSI 34 #define CONFIG_I2C_MVTWSI_BASE0 MVEBU_TWSI_BASE 35 #define CONFIG_SYS_I2C_SLAVE 0x0 36 #define CONFIG_SYS_I2C_SPEED 100000 37 38 /* SPI NOR flash default params, used by sf commands */ 39 #define CONFIG_SF_DEFAULT_SPEED 1000000 40 #define CONFIG_SF_DEFAULT_MODE SPI_MODE_3 41 #define CONFIG_SPI_FLASH_STMICRO 42 43 /* 44 * SDIO/MMC Card Configuration 45 */ 46 #define CONFIG_GENERIC_MMC 47 #define CONFIG_SYS_MMC_BASE MVEBU_SDIO_BASE 48 49 /* Partition support */ 50 #define CONFIG_DOS_PARTITION 51 #define CONFIG_EFI_PARTITION 52 53 /* Additional FS support/configuration */ 54 #define CONFIG_SUPPORT_VFAT 55 56 /* USB/EHCI configuration */ 57 #define CONFIG_EHCI_IS_TDI 58 59 #define CONFIG_ENV_MIN_ENTRIES 128 60 61 /* Environment in MMC */ 62 #define CONFIG_ENV_IS_IN_MMC 63 #define CONFIG_SYS_MMC_ENV_DEV 0 64 #define CONFIG_ENV_SECT_SIZE 0x200 65 #define CONFIG_ENV_SIZE 0x10000 66 /* 67 * For SD - reserve 1 LBA for MBR + 1M for u-boot image. The MMC/eMMC 68 * boot image starts @ LBA-0. 69 * As result in MMC/eMMC case it will be a 1 sector gap between u-boot 70 * image and environment 71 */ 72 #define CONFIG_ENV_OFFSET 0xf0000 73 #define CONFIG_ENV_ADDR CONFIG_ENV_OFFSET 74 75 #define CONFIG_PHY_MARVELL /* there is a marvell phy */ 76 #define PHY_ANEG_TIMEOUT 8000 /* PHY needs a longer aneg time */ 77 78 /* PCIe support */ 79 #ifndef CONFIG_SPL_BUILD 80 #define CONFIG_PCI_MVEBU 81 #define CONFIG_PCI_SCAN_SHOW 82 #endif 83 84 #define CONFIG_SYS_ALT_MEMTEST 85 86 /* Keep device tree and initrd in lower memory so the kernel can access them */ 87 #define CONFIG_EXTRA_ENV_SETTINGS \ 88 "fdt_high=0x10000000\0" \ 89 "initrd_high=0x10000000\0" 90 91 /* SPL */ 92 /* 93 * Select the boot device here 94 * 95 * Currently supported are: 96 * SPL_BOOT_SPI_NOR_FLASH - Booting via SPI NOR flash 97 * SPL_BOOT_SDIO_MMC_CARD - Booting via SDIO/MMC card (partition 1) 98 */ 99 #define SPL_BOOT_SPI_NOR_FLASH 1 100 #define SPL_BOOT_SDIO_MMC_CARD 2 101 #define CONFIG_SPL_BOOT_DEVICE SPL_BOOT_SDIO_MMC_CARD 102 103 /* Defines for SPL */ 104 #define CONFIG_SPL_FRAMEWORK 105 #define CONFIG_SPL_SIZE (140 << 10) 106 #define CONFIG_SPL_TEXT_BASE 0x40000030 107 #define CONFIG_SPL_MAX_SIZE (CONFIG_SPL_SIZE - 0x0030) 108 109 #define CONFIG_SPL_BSS_START_ADDR (0x40000000 + CONFIG_SPL_SIZE) 110 #define CONFIG_SPL_BSS_MAX_SIZE (16 << 10) 111 112 #ifdef CONFIG_SPL_BUILD 113 #define CONFIG_SYS_MALLOC_SIMPLE 114 #endif 115 116 #define CONFIG_SPL_STACK (0x40000000 + ((192 - 16) << 10)) 117 #define CONFIG_SPL_BOOTROM_SAVE (CONFIG_SPL_STACK + 4) 118 119 #if CONFIG_SPL_BOOT_DEVICE == SPL_BOOT_SPI_NOR_FLASH 120 /* SPL related SPI defines */ 121 #define CONFIG_SPL_SPI_LOAD 122 #define CONFIG_SYS_SPI_U_BOOT_OFFS 0x20000 123 #define CONFIG_SYS_U_BOOT_OFFS CONFIG_SYS_SPI_U_BOOT_OFFS 124 #endif 125 126 #if CONFIG_SPL_BOOT_DEVICE == SPL_BOOT_SDIO_MMC_CARD 127 /* SPL related MMC defines */ 128 #define CONFIG_SYS_MMC_U_BOOT_OFFS (160 << 10) 129 #define CONFIG_SYS_U_BOOT_OFFS CONFIG_SYS_MMC_U_BOOT_OFFS 130 #ifdef CONFIG_SPL_BUILD 131 #define CONFIG_FIXED_SDHCI_ALIGNED_BUFFER 0x00180000 /* in SDRAM */ 132 #endif 133 #endif 134 135 /* 136 * mv-common.h should be defined after CMD configs since it used them 137 * to enable certain macros 138 */ 139 #include "mv-common.h" 140 141 #endif /* _CONFIG_CLEARFOG_H */ 142