1 /* SPDX-License-Identifier: GPL-2.0+ */ 2 /* 3 * Copyright (C) 2011-2014 OMICRON electronics GmbH 4 * 5 * Based on da850evm.h. Original Copyrights follow: 6 * 7 * Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/ 8 * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net> 9 */ 10 11 #ifndef __CONFIG_H 12 #define __CONFIG_H 13 14 /* 15 * Board 16 */ 17 #define CONFIG_MACH_TYPE MACH_TYPE_CALIMAIN 18 19 /* 20 * SoC Configuration 21 */ 22 #define CONFIG_SYS_EXCEPTION_VECTORS_HIGH 23 #define CONFIG_SYS_CLK_FREQ clk_get(DAVINCI_ARM_CLKID) 24 #define CONFIG_SYS_OSCIN_FREQ calimain_get_osc_freq() 25 #define CONFIG_SYS_TIMERBASE DAVINCI_TIMER0_BASE 26 #define CONFIG_SYS_HZ_CLOCK clk_get(DAVINCI_AUXCLK_CLKID) 27 #define CONFIG_ARCH_CPU_INIT 28 #define CONFIG_HW_WATCHDOG 29 #define CONFIG_SYS_WDTTIMERBASE DAVINCI_TIMER1_BASE 30 #define CONFIG_SYS_WDT_PERIOD_LOW \ 31 (60 * CONFIG_SYS_OSCIN_FREQ) /* 60 s heartbeat */ 32 #define CONFIG_SYS_WDT_PERIOD_HIGH 0x0 33 #define CONFIG_SYS_DV_NOR_BOOT_CFG (0x11) 34 35 /* 36 * PLL configuration 37 */ 38 39 #define CONFIG_SYS_DA850_PLL0_PLLM \ 40 ((calimain_get_osc_freq() == 25000000) ? 23 : 24) 41 #define CONFIG_SYS_DA850_PLL1_PLLM \ 42 ((calimain_get_osc_freq() == 25000000) ? 20 : 21) 43 44 /* 45 * DDR2 memory configuration 46 */ 47 #define CONFIG_SYS_DA850_DDR2_DDRPHYCR (DV_DDR_PHY_PWRDNEN | \ 48 DV_DDR_PHY_EXT_STRBEN | \ 49 (0x4 << DV_DDR_PHY_RD_LATENCY_SHIFT)) 50 51 #define CONFIG_SYS_DA850_DDR2_SDBCR ( \ 52 (1 << DV_DDR_SDCR_DDR2EN_SHIFT) | \ 53 (1 << DV_DDR_SDCR_DDRDRIVE0_SHIFT) | \ 54 (1 << DV_DDR_SDCR_DDREN_SHIFT) | \ 55 (1 << DV_DDR_SDCR_SDRAMEN_SHIFT) | \ 56 (1 << DV_DDR_SDCR_BUS_WIDTH_SHIFT) | \ 57 (0x3 << DV_DDR_SDCR_CL_SHIFT) | \ 58 (0x3 << DV_DDR_SDCR_IBANK_SHIFT) | \ 59 (0x2 << DV_DDR_SDCR_PAGESIZE_SHIFT)) 60 61 /* SDBCR2 is only used if IBANK_POS bit in SDBCR is set */ 62 #define CONFIG_SYS_DA850_DDR2_SDBCR2 0 63 64 #define CONFIG_SYS_DA850_DDR2_SDTIMR ( \ 65 (16 << DV_DDR_SDTMR1_RFC_SHIFT) | \ 66 (1 << DV_DDR_SDTMR1_RP_SHIFT) | \ 67 (1 << DV_DDR_SDTMR1_RCD_SHIFT) | \ 68 (1 << DV_DDR_SDTMR1_WR_SHIFT) | \ 69 (5 << DV_DDR_SDTMR1_RAS_SHIFT) | \ 70 (7 << DV_DDR_SDTMR1_RC_SHIFT) | \ 71 (1 << DV_DDR_SDTMR1_RRD_SHIFT) | \ 72 (1 << DV_DDR_SDTMR1_WTR_SHIFT)) 73 74 #define CONFIG_SYS_DA850_DDR2_SDTIMR2 ( \ 75 (7 << DV_DDR_SDTMR2_RASMAX_SHIFT) | \ 76 (2 << DV_DDR_SDTMR2_XP_SHIFT) | \ 77 (0 << DV_DDR_SDTMR2_ODT_SHIFT) | \ 78 (18 << DV_DDR_SDTMR2_XSNR_SHIFT) | \ 79 (199 << DV_DDR_SDTMR2_XSRD_SHIFT) | \ 80 (0 << DV_DDR_SDTMR2_RTP_SHIFT) | \ 81 (2 << DV_DDR_SDTMR2_CKE_SHIFT)) 82 83 #define CONFIG_SYS_DA850_DDR2_SDRCR 0x000003FF 84 #define CONFIG_SYS_DA850_DDR2_PBBPR 0x30 85 86 /* 87 * Flash memory timing 88 */ 89 90 #define CONFIG_SYS_DA850_CS2CFG ( \ 91 DAVINCI_ABCR_WSETUP(2) | \ 92 DAVINCI_ABCR_WSTROBE(5) | \ 93 DAVINCI_ABCR_WHOLD(3) | \ 94 DAVINCI_ABCR_RSETUP(1) | \ 95 DAVINCI_ABCR_RSTROBE(14) | \ 96 DAVINCI_ABCR_RHOLD(0) | \ 97 DAVINCI_ABCR_TA(3) | \ 98 DAVINCI_ABCR_ASIZE_16BIT) 99 100 /* single 64 MB NOR flash device connected to CS2 and CS3 */ 101 #define CONFIG_SYS_DA850_CS3CFG CONFIG_SYS_DA850_CS2CFG 102 103 /* 104 * Memory Info 105 */ 106 #define CONFIG_SYS_MALLOC_LEN (0x10000 + 1*1024*1024) /* malloc() len */ 107 #define PHYS_SDRAM_1 DAVINCI_DDR_EMIF_DATA_BASE /* DDR Start */ 108 #define PHYS_SDRAM_1_SIZE (128 << 20) /* SDRAM size 128MB */ 109 #define CONFIG_MAX_RAM_BANK_SIZE (512 << 20) /* max size from SPRS586*/ 110 111 #define CONFIG_SYS_DA850_SYSCFG_SUSPSRC ( \ 112 DAVINCI_SYSCFG_SUSPSRC_TIMER0 | \ 113 DAVINCI_SYSCFG_SUSPSRC_SPI1 | \ 114 DAVINCI_SYSCFG_SUSPSRC_UART2 | \ 115 DAVINCI_SYSCFG_SUSPSRC_EMAC | \ 116 DAVINCI_SYSCFG_SUSPSRC_I2C) 117 118 /* memtest start addr */ 119 #define CONFIG_SYS_MEMTEST_START (PHYS_SDRAM_1 + 0x2000000) 120 121 /* memtest will be run on 16MB */ 122 #define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + (16 << 20)) 123 124 /* 125 * Serial Driver info 126 */ 127 #define CONFIG_SYS_NS16550_SERIAL 128 #define CONFIG_SYS_NS16550_REG_SIZE -4 /* NS16550 register size */ 129 #define CONFIG_SYS_NS16550_COM1 DAVINCI_UART2_BASE /* Base address of UART2 */ 130 #define CONFIG_SYS_NS16550_CLK clk_get(DAVINCI_UART2_CLKID) 131 132 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of flash banks */ 133 #define CONFIG_SYS_FLASH_SECT_SZ (128 << 10) /* 128KB */ 134 #define CONFIG_SYS_FLASH_BASE DAVINCI_ASYNC_EMIF_DATA_CE2_BASE 135 #define CONFIG_ENV_SECT_SIZE CONFIG_SYS_FLASH_SECT_SZ 136 #define CONFIG_ENV_ADDR \ 137 (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_FLASH_SECT_SZ * 2) 138 #define CONFIG_ENV_SIZE (128 << 10) 139 #define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE) 140 #define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE 141 #define PHYS_FLASH_SIZE (64 << 20) /* Flash size 64MB */ 142 #define CONFIG_SYS_MAX_FLASH_SECT \ 143 ((PHYS_FLASH_SIZE/CONFIG_SYS_FLASH_SECT_SZ) + 3) 144 145 /* 146 * Network & Ethernet Configuration 147 */ 148 #ifdef CONFIG_DRIVER_TI_EMAC 149 #define CONFIG_BOOTP_DNS2 150 #define CONFIG_BOOTP_SEND_HOSTNAME 151 #define CONFIG_NET_RETRY_COUNT 10 152 #endif 153 154 /* 155 * U-Boot general configuration 156 */ 157 #define CONFIG_BOOTFILE "uImage" /* Boot file name */ 158 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 159 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Args Buffer Size */ 160 #define CONFIG_SYS_LOAD_ADDR (PHYS_SDRAM_1 + 0x700000) 161 #define CONFIG_LOADADDR 0xc0700000 162 #define CONFIG_MX_CYCLIC 163 164 /* 165 * Linux Information 166 */ 167 #define LINUX_BOOT_PARAM_ADDR (PHYS_SDRAM_1 + 0x100) 168 #define CONFIG_CMDLINE_TAG 169 #define CONFIG_REVISION_TAG 170 #define CONFIG_SETUP_MEMORY_TAGS 171 #define CONFIG_BOOTCOMMAND "run checkupdate; run checkbutton;" 172 #define CONFIG_BOOT_RETRY_TIME 60 /* continue boot after 60 s inactivity */ 173 #define CONFIG_RESET_TO_RETRY 174 175 /* 176 * Default environment settings 177 * gpio0 = button, gpio1 = led green, gpio2 = led red 178 * verify = n ... disable kernel checksum verification for faster booting 179 */ 180 #define CONFIG_EXTRA_ENV_SETTINGS \ 181 "tftpdir=calimero\0" \ 182 "flashkernel=tftpboot $loadaddr $tftpdir/uImage; " \ 183 "erase 0x60800000 +0x400000; " \ 184 "cp.b $loadaddr 0x60800000 $filesize\0" \ 185 "flashrootfs=" \ 186 "tftpboot $loadaddr $tftpdir/rootfs.jffs2; " \ 187 "erase 0x60c00000 +0x2e00000; " \ 188 "cp.b $loadaddr 0x60c00000 $filesize\0" \ 189 "flashuboot=tftpboot $loadaddr $tftpdir/u-boot.bin; " \ 190 "protect off all; " \ 191 "erase 0x60000000 +0x80000; " \ 192 "cp.b $loadaddr 0x60000000 $filesize\0" \ 193 "flashrlk=tftpboot $loadaddr $tftpdir/uImage-rlk; " \ 194 "erase 0x60080000 +0x780000; " \ 195 "cp.b $loadaddr 0x60080000 $filesize\0" \ 196 "erase_persistent=erase 0x63a00000 +0x600000;\0" \ 197 "bootnor=setenv bootargs console=ttyS2,115200n8 " \ 198 "root=/dev/mtdblock3 rw rootfstype=jffs2 " \ 199 "rootwait ethaddr=$ethaddr; " \ 200 "gpio c 1; gpio s 2; bootm 0x60800000\0" \ 201 "bootrlk=gpio s 1; gpio s 2;" \ 202 "setenv bootargs console=ttyS2,115200n8 " \ 203 "ethaddr=$ethaddr; bootm 0x60080000\0" \ 204 "boottftp=setenv bootargs console=ttyS2,115200n8 " \ 205 "root=/dev/mtdblock3 rw rootfstype=jffs2 " \ 206 "rootwait ethaddr=$ethaddr; " \ 207 "tftpboot $loadaddr $tftpdir/uImage;" \ 208 "gpio c 1; gpio s 2; bootm $loadaddr\0" \ 209 "checkupdate=if test -n $update_flag; then " \ 210 "echo Previous update failed - starting RLK; " \ 211 "run bootrlk; fi; " \ 212 "if test -n $initial_setup; then " \ 213 "echo Running initial setup procedure; " \ 214 "sleep 1; run flashall; fi\0" \ 215 "product=accessory\0" \ 216 "serial=XX12345\0" \ 217 "checknor=" \ 218 "if gpio i 0; then run bootnor; fi;\0" \ 219 "checkrlk=" \ 220 "if gpio i 0; then run bootrlk; fi;\0" \ 221 "checkbutton=" \ 222 "run checknor; sleep 1;" \ 223 "run checknor; sleep 1;" \ 224 "run checknor; sleep 1;" \ 225 "run checknor; sleep 1;" \ 226 "run checknor;" \ 227 "gpio s 1; gpio s 2;" \ 228 "echo ---- Release button to boot RLK ----;" \ 229 "run checkrlk; sleep 1;" \ 230 "run checkrlk; sleep 1;" \ 231 "run checkrlk; sleep 1;" \ 232 "run checkrlk; sleep 1;" \ 233 "run checkrlk; sleep 1;" \ 234 "run checkrlk;" \ 235 "echo ---- Factory reset requested ----;" \ 236 "gpio c 1;" \ 237 "setenv factory_reset true;" \ 238 "saveenv;" \ 239 "run bootnor;\0" \ 240 "flashall=run flashrlk;" \ 241 "run flashkernel;" \ 242 "run flashrootfs;" \ 243 "setenv erase_datafs true;" \ 244 "setenv initial_setup;" \ 245 "saveenv;" \ 246 "run bootnor;\0" \ 247 "verify=n\0" \ 248 "clearenv=protect off all;" \ 249 "erase 0x60040000 +0x40000;\0" \ 250 "altbootcmd=run bootrlk\0" 251 252 #define CONFIG_PREBOOT \ 253 "echo Version: $ver; " \ 254 "echo Serial: $serial; " \ 255 "echo MAC: $ethaddr; " \ 256 "echo Product: $product; " \ 257 "gpio c 1; gpio c 2;" 258 259 /* additions for new relocation code, must added to all boards */ 260 #define CONFIG_SYS_SDRAM_BASE 0xc0000000 261 /* initial stack pointer in internal SRAM */ 262 #define CONFIG_SYS_INIT_SP_ADDR (0x8001ff00) 263 264 #define CONFIG_SYS_BOOTCOUNT_LE /* Use little-endian accessors */ 265 266 #ifndef __ASSEMBLY__ 267 int calimain_get_osc_freq(void); 268 #endif 269 270 #include <asm/arch/hardware.h> 271 272 #endif /* __CONFIG_H */ 273