1 /* SPDX-License-Identifier: GPL-2.0+ */ 2 /* 3 * Copyright (C) 2011-2014 OMICRON electronics GmbH 4 * 5 * Based on da850evm.h. Original Copyrights follow: 6 * 7 * Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/ 8 * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net> 9 */ 10 11 #ifndef __CONFIG_H 12 #define __CONFIG_H 13 14 /* 15 * Board 16 */ 17 #define CONFIG_MACH_TYPE MACH_TYPE_CALIMAIN 18 19 /* 20 * SoC Configuration 21 */ 22 #define CONFIG_SYS_EXCEPTION_VECTORS_HIGH 23 #define CONFIG_SYS_CLK_FREQ clk_get(DAVINCI_ARM_CLKID) 24 #define CONFIG_SYS_OSCIN_FREQ calimain_get_osc_freq() 25 #define CONFIG_SYS_TIMERBASE DAVINCI_TIMER0_BASE 26 #define CONFIG_SYS_HZ_CLOCK clk_get(DAVINCI_AUXCLK_CLKID) 27 #define CONFIG_ARCH_CPU_INIT 28 #define CONFIG_HW_WATCHDOG 29 #define CONFIG_SYS_WDTTIMERBASE DAVINCI_TIMER1_BASE 30 #define CONFIG_SYS_WDT_PERIOD_LOW \ 31 (60 * CONFIG_SYS_OSCIN_FREQ) /* 60 s heartbeat */ 32 #define CONFIG_SYS_WDT_PERIOD_HIGH 0x0 33 #define CONFIG_SYS_DV_NOR_BOOT_CFG (0x11) 34 35 /* 36 * PLL configuration 37 */ 38 39 #define CONFIG_SYS_DA850_PLL0_PLLM \ 40 ((calimain_get_osc_freq() == 25000000) ? 23 : 24) 41 #define CONFIG_SYS_DA850_PLL1_PLLM \ 42 ((calimain_get_osc_freq() == 25000000) ? 20 : 21) 43 44 /* 45 * DDR2 memory configuration 46 */ 47 #define CONFIG_SYS_DA850_DDR2_DDRPHYCR (DV_DDR_PHY_PWRDNEN | \ 48 DV_DDR_PHY_EXT_STRBEN | \ 49 (0x4 << DV_DDR_PHY_RD_LATENCY_SHIFT)) 50 51 #define CONFIG_SYS_DA850_DDR2_SDBCR ( \ 52 (1 << DV_DDR_SDCR_DDR2EN_SHIFT) | \ 53 (1 << DV_DDR_SDCR_DDRDRIVE0_SHIFT) | \ 54 (1 << DV_DDR_SDCR_DDREN_SHIFT) | \ 55 (1 << DV_DDR_SDCR_SDRAMEN_SHIFT) | \ 56 (1 << DV_DDR_SDCR_BUS_WIDTH_SHIFT) | \ 57 (0x3 << DV_DDR_SDCR_CL_SHIFT) | \ 58 (0x3 << DV_DDR_SDCR_IBANK_SHIFT) | \ 59 (0x2 << DV_DDR_SDCR_PAGESIZE_SHIFT)) 60 61 /* SDBCR2 is only used if IBANK_POS bit in SDBCR is set */ 62 #define CONFIG_SYS_DA850_DDR2_SDBCR2 0 63 64 #define CONFIG_SYS_DA850_DDR2_SDTIMR ( \ 65 (16 << DV_DDR_SDTMR1_RFC_SHIFT) | \ 66 (1 << DV_DDR_SDTMR1_RP_SHIFT) | \ 67 (1 << DV_DDR_SDTMR1_RCD_SHIFT) | \ 68 (1 << DV_DDR_SDTMR1_WR_SHIFT) | \ 69 (5 << DV_DDR_SDTMR1_RAS_SHIFT) | \ 70 (7 << DV_DDR_SDTMR1_RC_SHIFT) | \ 71 (1 << DV_DDR_SDTMR1_RRD_SHIFT) | \ 72 (1 << DV_DDR_SDTMR1_WTR_SHIFT)) 73 74 #define CONFIG_SYS_DA850_DDR2_SDTIMR2 ( \ 75 (7 << DV_DDR_SDTMR2_RASMAX_SHIFT) | \ 76 (2 << DV_DDR_SDTMR2_XP_SHIFT) | \ 77 (0 << DV_DDR_SDTMR2_ODT_SHIFT) | \ 78 (18 << DV_DDR_SDTMR2_XSNR_SHIFT) | \ 79 (199 << DV_DDR_SDTMR2_XSRD_SHIFT) | \ 80 (0 << DV_DDR_SDTMR2_RTP_SHIFT) | \ 81 (2 << DV_DDR_SDTMR2_CKE_SHIFT)) 82 83 #define CONFIG_SYS_DA850_DDR2_SDRCR 0x000003FF 84 #define CONFIG_SYS_DA850_DDR2_PBBPR 0x30 85 86 /* 87 * Flash memory timing 88 */ 89 90 #define CONFIG_SYS_DA850_CS2CFG ( \ 91 DAVINCI_ABCR_WSETUP(2) | \ 92 DAVINCI_ABCR_WSTROBE(5) | \ 93 DAVINCI_ABCR_WHOLD(3) | \ 94 DAVINCI_ABCR_RSETUP(1) | \ 95 DAVINCI_ABCR_RSTROBE(14) | \ 96 DAVINCI_ABCR_RHOLD(0) | \ 97 DAVINCI_ABCR_TA(3) | \ 98 DAVINCI_ABCR_ASIZE_16BIT) 99 100 /* single 64 MB NOR flash device connected to CS2 and CS3 */ 101 #define CONFIG_SYS_DA850_CS3CFG CONFIG_SYS_DA850_CS2CFG 102 103 /* 104 * Memory Info 105 */ 106 #define CONFIG_SYS_MALLOC_LEN (0x10000 + 1*1024*1024) /* malloc() len */ 107 #define PHYS_SDRAM_1 DAVINCI_DDR_EMIF_DATA_BASE /* DDR Start */ 108 #define PHYS_SDRAM_1_SIZE (128 << 20) /* SDRAM size 128MB */ 109 #define CONFIG_MAX_RAM_BANK_SIZE (512 << 20) /* max size from SPRS586*/ 110 111 #define CONFIG_SYS_DA850_SYSCFG_SUSPSRC ( \ 112 DAVINCI_SYSCFG_SUSPSRC_TIMER0 | \ 113 DAVINCI_SYSCFG_SUSPSRC_SPI1 | \ 114 DAVINCI_SYSCFG_SUSPSRC_UART2 | \ 115 DAVINCI_SYSCFG_SUSPSRC_EMAC | \ 116 DAVINCI_SYSCFG_SUSPSRC_I2C) 117 118 /* memtest start addr */ 119 #define CONFIG_SYS_MEMTEST_START (PHYS_SDRAM_1 + 0x2000000) 120 121 /* memtest will be run on 16MB */ 122 #define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + (16 << 20)) 123 124 /* 125 * Serial Driver info 126 */ 127 #define CONFIG_SYS_NS16550_SERIAL 128 #define CONFIG_SYS_NS16550_REG_SIZE -4 /* NS16550 register size */ 129 #define CONFIG_SYS_NS16550_COM1 DAVINCI_UART2_BASE /* Base address of UART2 */ 130 #define CONFIG_SYS_NS16550_CLK clk_get(DAVINCI_UART2_CLKID) 131 132 #define CONFIG_FLASH_CFI_DRIVER 133 #define CONFIG_SYS_FLASH_CFI 134 #define CONFIG_SYS_FLASH_PROTECTION 135 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 136 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of flash banks */ 137 #define CONFIG_SYS_FLASH_SECT_SZ (128 << 10) /* 128KB */ 138 #define CONFIG_SYS_FLASH_BASE DAVINCI_ASYNC_EMIF_DATA_CE2_BASE 139 #define CONFIG_ENV_SECT_SIZE CONFIG_SYS_FLASH_SECT_SZ 140 #define CONFIG_ENV_ADDR \ 141 (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_FLASH_SECT_SZ * 2) 142 #define CONFIG_ENV_SIZE (128 << 10) 143 #define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE) 144 #define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE 145 #define PHYS_FLASH_SIZE (64 << 20) /* Flash size 64MB */ 146 #define CONFIG_SYS_MAX_FLASH_SECT \ 147 ((PHYS_FLASH_SIZE/CONFIG_SYS_FLASH_SECT_SZ) + 3) 148 149 /* 150 * Network & Ethernet Configuration 151 */ 152 #ifdef CONFIG_DRIVER_TI_EMAC 153 #define CONFIG_BOOTP_DNS2 154 #define CONFIG_BOOTP_SEND_HOSTNAME 155 #define CONFIG_NET_RETRY_COUNT 10 156 #endif 157 158 /* 159 * U-Boot general configuration 160 */ 161 #define CONFIG_BOOTFILE "uImage" /* Boot file name */ 162 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 163 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Args Buffer Size */ 164 #define CONFIG_SYS_LOAD_ADDR (PHYS_SDRAM_1 + 0x700000) 165 #define CONFIG_LOADADDR 0xc0700000 166 #define CONFIG_MX_CYCLIC 167 168 /* 169 * Linux Information 170 */ 171 #define LINUX_BOOT_PARAM_ADDR (PHYS_SDRAM_1 + 0x100) 172 #define CONFIG_CMDLINE_TAG 173 #define CONFIG_REVISION_TAG 174 #define CONFIG_SETUP_MEMORY_TAGS 175 #define CONFIG_BOOTCOMMAND "run checkupdate; run checkbutton;" 176 #define CONFIG_BOOT_RETRY_TIME 60 /* continue boot after 60 s inactivity */ 177 #define CONFIG_RESET_TO_RETRY 178 179 /* 180 * Default environment settings 181 * gpio0 = button, gpio1 = led green, gpio2 = led red 182 * verify = n ... disable kernel checksum verification for faster booting 183 */ 184 #define CONFIG_EXTRA_ENV_SETTINGS \ 185 "tftpdir=calimero\0" \ 186 "flashkernel=tftpboot $loadaddr $tftpdir/uImage; " \ 187 "erase 0x60800000 +0x400000; " \ 188 "cp.b $loadaddr 0x60800000 $filesize\0" \ 189 "flashrootfs=" \ 190 "tftpboot $loadaddr $tftpdir/rootfs.jffs2; " \ 191 "erase 0x60c00000 +0x2e00000; " \ 192 "cp.b $loadaddr 0x60c00000 $filesize\0" \ 193 "flashuboot=tftpboot $loadaddr $tftpdir/u-boot.bin; " \ 194 "protect off all; " \ 195 "erase 0x60000000 +0x80000; " \ 196 "cp.b $loadaddr 0x60000000 $filesize\0" \ 197 "flashrlk=tftpboot $loadaddr $tftpdir/uImage-rlk; " \ 198 "erase 0x60080000 +0x780000; " \ 199 "cp.b $loadaddr 0x60080000 $filesize\0" \ 200 "erase_persistent=erase 0x63a00000 +0x600000;\0" \ 201 "bootnor=setenv bootargs console=ttyS2,115200n8 " \ 202 "root=/dev/mtdblock3 rw rootfstype=jffs2 " \ 203 "rootwait ethaddr=$ethaddr; " \ 204 "gpio c 1; gpio s 2; bootm 0x60800000\0" \ 205 "bootrlk=gpio s 1; gpio s 2;" \ 206 "setenv bootargs console=ttyS2,115200n8 " \ 207 "ethaddr=$ethaddr; bootm 0x60080000\0" \ 208 "boottftp=setenv bootargs console=ttyS2,115200n8 " \ 209 "root=/dev/mtdblock3 rw rootfstype=jffs2 " \ 210 "rootwait ethaddr=$ethaddr; " \ 211 "tftpboot $loadaddr $tftpdir/uImage;" \ 212 "gpio c 1; gpio s 2; bootm $loadaddr\0" \ 213 "checkupdate=if test -n $update_flag; then " \ 214 "echo Previous update failed - starting RLK; " \ 215 "run bootrlk; fi; " \ 216 "if test -n $initial_setup; then " \ 217 "echo Running initial setup procedure; " \ 218 "sleep 1; run flashall; fi\0" \ 219 "product=accessory\0" \ 220 "serial=XX12345\0" \ 221 "checknor=" \ 222 "if gpio i 0; then run bootnor; fi;\0" \ 223 "checkrlk=" \ 224 "if gpio i 0; then run bootrlk; fi;\0" \ 225 "checkbutton=" \ 226 "run checknor; sleep 1;" \ 227 "run checknor; sleep 1;" \ 228 "run checknor; sleep 1;" \ 229 "run checknor; sleep 1;" \ 230 "run checknor;" \ 231 "gpio s 1; gpio s 2;" \ 232 "echo ---- Release button to boot RLK ----;" \ 233 "run checkrlk; sleep 1;" \ 234 "run checkrlk; sleep 1;" \ 235 "run checkrlk; sleep 1;" \ 236 "run checkrlk; sleep 1;" \ 237 "run checkrlk; sleep 1;" \ 238 "run checkrlk;" \ 239 "echo ---- Factory reset requested ----;" \ 240 "gpio c 1;" \ 241 "setenv factory_reset true;" \ 242 "saveenv;" \ 243 "run bootnor;\0" \ 244 "flashall=run flashrlk;" \ 245 "run flashkernel;" \ 246 "run flashrootfs;" \ 247 "setenv erase_datafs true;" \ 248 "setenv initial_setup;" \ 249 "saveenv;" \ 250 "run bootnor;\0" \ 251 "verify=n\0" \ 252 "clearenv=protect off all;" \ 253 "erase 0x60040000 +0x40000;\0" \ 254 "altbootcmd=run bootrlk\0" 255 256 #define CONFIG_PREBOOT \ 257 "echo Version: $ver; " \ 258 "echo Serial: $serial; " \ 259 "echo MAC: $ethaddr; " \ 260 "echo Product: $product; " \ 261 "gpio c 1; gpio c 2;" 262 263 /* additions for new relocation code, must added to all boards */ 264 #define CONFIG_SYS_SDRAM_BASE 0xc0000000 265 /* initial stack pointer in internal SRAM */ 266 #define CONFIG_SYS_INIT_SP_ADDR (0x8001ff00) 267 268 #define CONFIG_SYS_BOOTCOUNT_LE /* Use little-endian accessors */ 269 270 #ifndef __ASSEMBLY__ 271 int calimain_get_osc_freq(void); 272 #endif 273 274 #include <asm/arch/hardware.h> 275 276 #endif /* __CONFIG_H */ 277