1 /*
2  * bur_am335x_common.h
3  *
4  * common parts used by B&R AM335x based boards
5  *
6  * Copyright (C) 2016 Hannes Schmelzer <oe5hpm@oevsv.at> -
7  * Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com
8  *
9  * SPDX-License-Identifier:        GPL-2.0+
10  */
11 
12 #ifndef __BUR_AM335X_COMMON_H__
13 #define __BUR_AM335X_COMMON_H__
14 /* ------------------------------------------------------------------------- */
15 #define CONFIG_MAX_RAM_BANK_SIZE	(1024 << 20)	/* 1GB */
16 
17 /* Timer information */
18 #define CONFIG_SYS_PTV			2	/* Divisor: 2^(PTV+1) => 8 */
19 #define CONFIG_SYS_TIMERBASE		0x48040000	/* Use Timer2 */
20 #define CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC	/* enable 32kHz OSC at bootime */
21 #define CONFIG_POWER_TPS65217
22 
23 #include <asm/arch/omap.h>
24 
25 /* NS16550 Configuration */
26 #define CONFIG_SYS_NS16550_SERIAL
27 #define CONFIG_SYS_NS16550_REG_SIZE	(-4)
28 #define CONFIG_SYS_NS16550_CLK		48000000
29 #define CONFIG_SYS_NS16550_COM1		0x44e09000	/* UART0 */
30 
31 /* Network defines */
32 #define CONFIG_DRIVER_TI_CPSW		/* Driver for IP block */
33 #define CONFIG_MII			/* Required in net/eth.c */
34 #define CONFIG_PHY_NATSEMI
35 
36 /*
37  * SPL related defines.  The Public RAM memory map the ROM defines the
38  * area between 0x402F0400 and 0x4030B800 as a download area and
39  * 0x4030B800 to 0x4030CE00 as a public stack area.  The ROM also
40  * supports X-MODEM loading via UART, and we leverage this and then use
41  * Y-MODEM to load u-boot.img, when booted over UART.  We must also include
42  * the scratch space that U-Boot uses in SRAM.
43  */
44 #define CONFIG_SPL_TEXT_BASE		0x402F0400
45 #define CONFIG_SPL_MAX_SIZE		(SRAM_SCRATCH_SPACE_ADDR - \
46 					 CONFIG_SPL_TEXT_BASE)
47 
48 /*
49  * Since SPL did pll and ddr initialization for us,
50  * we don't need to do it twice.
51  */
52 #if !defined(CONFIG_SPL_BUILD) && !defined(CONFIG_NOR_BOOT)
53 #define CONFIG_SKIP_LOWLEVEL_INIT
54 #endif /* !CONFIG_SPL_BUILD, ... */
55 /*
56  * Our DDR memory always starts at 0x80000000 and U-Boot shall have
57  * relocated itself to higher in memory by the time this value is used.
58  */
59 #define CONFIG_SYS_LOAD_ADDR		0x80000000
60 /*
61  * ----------------------------------------------------------------------------
62  * DDR information.  We say (for simplicity) that we have 1 bank,
63  * always, even when we have more.  We always start at 0x80000000,
64  * and we place the initial stack pointer in our SRAM.
65  */
66 #define CONFIG_NR_DRAM_BANKS		1
67 #define CONFIG_SYS_SDRAM_BASE		0x80000000
68 #define CONFIG_SYS_INIT_SP_ADDR		(NON_SECURE_SRAM_END - \
69 					GENERATED_GBL_DATA_SIZE)
70 
71 /* I2C */
72 #define CONFIG_SYS_I2C
73 #define CONFIG_SYS_OMAP24_I2C_SPEED	100000
74 #define CONFIG_SYS_OMAP24_I2C_SLAVE	1
75 
76 /*
77  * Our platforms make use of SPL to initalize the hardware (primarily
78  * memory) enough for full U-Boot to be loaded.  We also support Falcon
79  * Mode so that the Linux kernel can be booted directly from SPL
80  * instead, if desired.  We make use of the general SPL framework found
81  * under common/spl/.  Given our generally common memory map, we set a
82  * number of related defaults and sizes here.
83  */
84 #define CONFIG_SPL_FRAMEWORK
85 /*
86  * Place the image at the start of the ROM defined image space.
87  * We limit our size to the ROM-defined downloaded image area, and use the
88  * rest of the space for stack.  We load U-Boot itself into memory at
89  * 0x80800000 for legacy reasons (to not conflict with older SPLs).  We
90  * have our BSS be placed 1MiB after this, to allow for the default
91  * Linux kernel address of 0x80008000 to work, in the Falcon Mode case.
92  * We have the SPL malloc pool at the end of the BSS area.
93  *
94  * ----------------------------------------------------------------------------
95  */
96 #undef  CONFIG_SYS_TEXT_BASE
97 #define CONFIG_SYS_TEXT_BASE		0x80800000
98 #define CONFIG_SPL_BSS_START_ADDR	0x80A00000
99 #define CONFIG_SPL_BSS_MAX_SIZE		0x80000		/* 512 KB */
100 #define CONFIG_SYS_SPL_MALLOC_START	(CONFIG_SPL_BSS_START_ADDR + \
101 					CONFIG_SPL_BSS_MAX_SIZE)
102 #define CONFIG_SYS_SPL_MALLOC_SIZE	CONFIG_SYS_MALLOC_LEN
103 
104 /* General parts of the framework, required. */
105 
106 #endif	/* ! __BUR_AM335X_COMMON_H__ */
107