1 /* SPDX-License-Identifier: GPL-2.0+ */ 2 /* 3 * bur_am335x_common.h 4 * 5 * common parts used by B&R AM335x based boards 6 * 7 * Copyright (C) 2016 Hannes Schmelzer <oe5hpm@oevsv.at> - 8 * Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com 9 */ 10 11 #ifndef __BUR_AM335X_COMMON_H__ 12 #define __BUR_AM335X_COMMON_H__ 13 /* ------------------------------------------------------------------------- */ 14 15 /* legacy #defines for non DM bur-board */ 16 #ifndef CONFIG_DM 17 #define CONFIG_SYS_NS16550_SERIAL 18 #define CONFIG_SYS_NS16550_REG_SIZE (-4) 19 #define CONFIG_SYS_NS16550_CLK (48000000) 20 #define CONFIG_SYS_NS16550_COM1 0x44e09000 21 22 #define CONFIG_I2C 23 #define CONFIG_SYS_I2C 24 25 #endif /* CONFIG_DM */ 26 27 #define CONFIG_MAX_RAM_BANK_SIZE (1024 << 20) /* 1GB */ 28 29 /* Timer information */ 30 #define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */ 31 #define CONFIG_SYS_TIMERBASE 0x48040000 /* Use Timer2 */ 32 #define CONFIG_POWER_TPS65217 33 34 #include <asm/arch/omap.h> 35 36 /* 37 * SPL related defines. The Public RAM memory map the ROM defines the 38 * area between 0x402F0400 and 0x4030B800 as a download area and 39 * 0x4030B800 to 0x4030CE00 as a public stack area. The ROM also 40 * supports X-MODEM loading via UART, and we leverage this and then use 41 * Y-MODEM to load u-boot.img, when booted over UART. We must also include 42 * the scratch space that U-Boot uses in SRAM. 43 */ 44 #define CONFIG_SPL_TEXT_BASE 0x402F0400 45 #define CONFIG_SPL_MAX_SIZE (SRAM_SCRATCH_SPACE_ADDR - \ 46 CONFIG_SPL_TEXT_BASE) 47 48 /* 49 * Since SPL did pll and ddr initialization for us, 50 * we don't need to do it twice. 51 */ 52 #if !defined(CONFIG_SPL_BUILD) && !defined(CONFIG_NOR_BOOT) 53 #define CONFIG_SKIP_LOWLEVEL_INIT 54 #endif /* !CONFIG_SPL_BUILD, ... */ 55 /* 56 * Our DDR memory always starts at 0x80000000 and U-Boot shall have 57 * relocated itself to higher in memory by the time this value is used. 58 */ 59 #define CONFIG_SYS_LOAD_ADDR 0x80000000 60 /* 61 * ---------------------------------------------------------------------------- 62 * DDR information. We say (for simplicity) that we have 1 bank, 63 * always, even when we have more. We always start at 0x80000000, 64 * and we place the initial stack pointer in our SRAM. 65 */ 66 #define CONFIG_SYS_SDRAM_BASE 0x80000000 67 #define CONFIG_SYS_INIT_SP_ADDR (NON_SECURE_SRAM_END - \ 68 GENERATED_GBL_DATA_SIZE) 69 70 /* 71 * Our platforms make use of SPL to initalize the hardware (primarily 72 * memory) enough for full U-Boot to be loaded. We also support Falcon 73 * Mode so that the Linux kernel can be booted directly from SPL 74 * instead, if desired. We make use of the general SPL framework found 75 * under common/spl/. Given our generally common memory map, we set a 76 * number of related defaults and sizes here. 77 */ 78 /* 79 * Place the image at the start of the ROM defined image space. 80 * We limit our size to the ROM-defined downloaded image area, and use the 81 * rest of the space for stack. We load U-Boot itself into memory at 82 * 0x80800000 for legacy reasons (to not conflict with older SPLs). We 83 * have our BSS be placed 1MiB after this, to allow for the default 84 * Linux kernel address of 0x80008000 to work, in the Falcon Mode case. 85 * We have the SPL malloc pool at the end of the BSS area. 86 * 87 * ---------------------------------------------------------------------------- 88 */ 89 #define CONFIG_SPL_BSS_START_ADDR 0x80A00000 90 #define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */ 91 #define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SPL_BSS_START_ADDR + \ 92 CONFIG_SPL_BSS_MAX_SIZE) 93 #define CONFIG_SYS_SPL_MALLOC_SIZE CONFIG_SYS_MALLOC_LEN 94 95 /* General parts of the framework, required. */ 96 97 #endif /* ! __BUR_AM335X_COMMON_H__ */ 98