1 /*
2  * Copyright 2013 Broadcom Corporation.
3  *
4  * SPDX-License-Identifier:	GPL-2.0+
5  */
6 
7 #ifndef __BCM23550_W1D_H
8 #define __BCM23550_W1D_H
9 
10 #include <linux/sizes.h>
11 #include <asm/arch/sysmap.h>
12 
13 /* CPU, chip, mach, etc */
14 #define CONFIG_KONA
15 #define CONFIG_SKIP_LOWLEVEL_INIT
16 #define CONFIG_KONA_RESET_S
17 
18 /*
19  * Memory configuration
20  */
21 
22 #define CONFIG_SYS_SDRAM_BASE		0x80000000
23 #define CONFIG_SYS_SDRAM_SIZE		0x20000000
24 #define CONFIG_NR_DRAM_BANKS		1
25 
26 #define CONFIG_SYS_MALLOC_LEN		SZ_4M	/* see armv7/start.S. */
27 
28 /* GPIO Driver */
29 #define CONFIG_KONA_GPIO
30 
31 /* MMC/SD Driver */
32 #define CONFIG_SYS_SDIO_BASE0 SDIO1_BASE_ADDR
33 #define CONFIG_SYS_SDIO_BASE1 SDIO2_BASE_ADDR
34 #define CONFIG_SYS_SDIO_BASE2 SDIO3_BASE_ADDR
35 #define CONFIG_SYS_SDIO_BASE3 SDIO4_BASE_ADDR
36 #define CONFIG_SYS_SDIO0_MAX_CLK 48000000
37 #define CONFIG_SYS_SDIO1_MAX_CLK 48000000
38 #define CONFIG_SYS_SDIO2_MAX_CLK 48000000
39 #define CONFIG_SYS_SDIO3_MAX_CLK 48000000
40 #define CONFIG_SYS_SDIO0 "sdio1"
41 #define CONFIG_SYS_SDIO1 "sdio2"
42 #define CONFIG_SYS_SDIO2 "sdio3"
43 #define CONFIG_SYS_SDIO3 "sdio4"
44 
45 /* I2C Driver */
46 #define CONFIG_SYS_I2C
47 #define CONFIG_SYS_I2C_KONA
48 #define CONFIG_SYS_SPD_BUS_NUM	3	/* Start with PMU bus */
49 #define CONFIG_SYS_MAX_I2C_BUS	4
50 #define CONFIG_SYS_I2C_BASE0	BSC1_BASE_ADDR
51 #define CONFIG_SYS_I2C_BASE1	BSC2_BASE_ADDR
52 #define CONFIG_SYS_I2C_BASE2	BSC3_BASE_ADDR
53 #define CONFIG_SYS_I2C_BASE3	PMU_BSC_BASE_ADDR
54 
55 /* Timer Driver */
56 #define CONFIG_SYS_TIMER_RATE		32000
57 #define CONFIG_SYS_TIMER_COUNTER	(TIMER_BASE_ADDR + 4) /* STCLO offset */
58 
59 /* Init functions */
60 #define CONFIG_MISC_INIT_R	/* board's misc_init_r function */
61 
62 /* Some commands use this as the default load address */
63 #define CONFIG_SYS_LOAD_ADDR		CONFIG_SYS_SDRAM_BASE
64 
65 /* No mtest functions as recommended */
66 
67 /*
68  * This is the initial SP which is used only briefly for relocating the u-boot
69  * image to the top of SDRAM. After relocation u-boot moves the stack to the
70  * proper place.
71  */
72 #define CONFIG_SYS_INIT_SP_ADDR		CONFIG_SYS_TEXT_BASE
73 
74 /* Serial Info */
75 #define CONFIG_SYS_NS16550_SERIAL
76 /* Post pad 3 bytes after each reg addr */
77 #define CONFIG_SYS_NS16550_REG_SIZE	(-4)
78 #define CONFIG_SYS_NS16550_CLK		13000000
79 #define CONFIG_SYS_NS16550_COM1		0x3e000000
80 
81 /* must fit into GPT:u-boot-env partition */
82 #define CONFIG_SYS_MMC_ENV_DEV		0
83 #define CONFIG_ENV_OFFSET		(0x00011a00 * 512)
84 #define CONFIG_ENV_SIZE			(8 * 512)
85 
86 /* console configuration */
87 #define CONFIG_SYS_CBSIZE		1024	/* Console buffer size */
88 #define CONFIG_SYS_MAXARGS		64
89 #define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE
90 
91 /*
92  * One partition type must be defined for part.c
93  * This is necessary for the fatls command to work on an SD card
94  * for example.
95  */
96 
97 /* version string, parser, etc */
98 
99 #define CONFIG_MX_CYCLIC
100 
101 /* Initial upstream - boot to cmd prompt only */
102 #define CONFIG_BOOTCOMMAND		""
103 
104 #define CONFIG_USBID_ADDR		0x34052c46
105 
106 #define CONFIG_SYS_ICACHE_OFF
107 #define CONFIG_SYS_DCACHE_OFF
108 #define CONFIG_SYS_L2CACHE_OFF
109 
110 #endif /* __BCM23550_W1D_H */
111