1 /* 2 * Copyright (C) 2010 Andreas Bießmann <biessmann.devel@googlemail.com> 3 * 4 * based on previous work by 5 * 6 * Ulf Samuelsson <ulf@atmel.com> 7 * Rick Bronson <rick@efn.org> 8 * 9 * Configuration settings for the AT91RM9200EK board. 10 * 11 * SPDX-License-Identifier: GPL-2.0+ 12 */ 13 14 #ifndef __AT91RM9200EK_CONFIG_H__ 15 #define __AT91RM9200EK_CONFIG_H__ 16 17 #include <linux/sizes.h> 18 19 /* 20 * set some initial configurations depending on configure target 21 * 22 * at91rm9200ek_config -> boot from 0x0 in NOR Flash at CS0 23 * at91rm9200ek_ram_config -> continue booting from 0x20100000 in RAM; lowlevel 24 * initialisation was done by some preloader 25 */ 26 #ifdef CONFIG_RAMBOOT 27 #define CONFIG_SKIP_LOWLEVEL_INIT 28 #define CONFIG_SYS_TEXT_BASE 0x20100000 29 #else 30 #define CONFIG_SYS_TEXT_BASE 0x10000000 31 #endif 32 33 /* 34 * AT91C_XTAL_CLOCK is the frequency of external xtal in hertz 35 * AT91C_MAIN_CLOCK is the frequency of PLLA output 36 * AT91C_MASTER_CLOCK is the peripherial clock 37 * CONFIG_SYS_HZ_CLOCK is the value for CCR in tc0 (divider 2 is implicitely 38 * set in arch/arm/cpu/arm920t/at91/timer.c) 39 * CONFIG_SYS_HZ is the tick rate for timer tc0 40 */ 41 #define AT91C_XTAL_CLOCK 18432000 42 #define CONFIG_SYS_AT91_SLOW_CLOCK 32768 43 #define AT91C_MAIN_CLOCK ((AT91C_XTAL_CLOCK / 4) * 39) 44 #define AT91C_MASTER_CLOCK (AT91C_MAIN_CLOCK / 3 ) 45 #define CONFIG_SYS_HZ_CLOCK (AT91C_MASTER_CLOCK / 2) 46 47 /* CPU configuration */ 48 #define CONFIG_AT91RM9200 49 #define CONFIG_AT91RM9200EK 50 #define CONFIG_CPUAT91 51 #define USE_920T_MMU 52 53 #include <asm/hardware.h> /* needed for port definitions */ 54 55 #define CONFIG_CMDLINE_TAG 56 #define CONFIG_SETUP_MEMORY_TAGS 57 #define CONFIG_INITRD_TAG 58 59 #define CONFIG_BOARD_EARLY_INIT_F 60 61 /* 62 * Memory Configuration 63 */ 64 #define CONFIG_NR_DRAM_BANKS 1 65 #define CONFIG_SYS_SDRAM_BASE 0x20000000 66 #define CONFIG_SYS_SDRAM_SIZE SZ_32M 67 68 #define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE 69 #define CONFIG_SYS_MEMTEST_END \ 70 (CONFIG_SYS_MEMTEST_START + CONFIG_SYS_SDRAM_SIZE - SZ_256K) 71 72 /* 73 * LowLevel Init 74 */ 75 #ifndef CONFIG_SKIP_LOWLEVEL_INIT 76 #define CONFIG_SYS_USE_MAIN_OSCILLATOR 77 /* flash */ 78 #define CONFIG_SYS_EBI_CFGR_VAL 0x00000000 79 #define CONFIG_SYS_SMC_CSR0_VAL 0x00003284 /* 16bit, 2 TDF, 4 WS */ 80 81 /* clocks */ 82 #define CONFIG_SYS_PLLAR_VAL 0x20263E04 /* 179.712000 MHz for PCK */ 83 #define CONFIG_SYS_PLLBR_VAL 0x10483E0E /* 48.054857 MHz (divider by 2 for USB) */ 84 /* PCK/3 = MCK Master Clock = 59.904000MHz from PLLA */ 85 #define CONFIG_SYS_MCKR_VAL 0x00000202 86 87 /* sdram */ 88 #define CONFIG_SYS_PIOC_ASR_VAL 0xFFFF0000 /* Configure PIOC as peripheral (D16/D31) */ 89 #define CONFIG_SYS_PIOC_BSR_VAL 0x00000000 90 #define CONFIG_SYS_PIOC_PDR_VAL 0xFFFF0000 91 #define CONFIG_SYS_EBI_CSA_VAL 0x00000002 /* CS1=CONFIG_SYS_SDRAM */ 92 #define CONFIG_SYS_SDRC_CR_VAL 0x2188c155 /* set up the CONFIG_SYS_SDRAM */ 93 #define CONFIG_SYS_SDRAM CONFIG_SYS_SDRAM_BASE /* address of the SDRAM */ 94 #define CONFIG_SYS_SDRAM1 (CONFIG_SYS_SDRAM_BASE+0x80) 95 #define CONFIG_SYS_SDRAM_VAL 0x00000000 /* value written to CONFIG_SYS_SDRAM */ 96 #define CONFIG_SYS_SDRC_MR_VAL 0x00000002 /* Precharge All */ 97 #define CONFIG_SYS_SDRC_MR_VAL1 0x00000004 /* refresh */ 98 #define CONFIG_SYS_SDRC_MR_VAL2 0x00000003 /* Load Mode Register */ 99 #define CONFIG_SYS_SDRC_MR_VAL3 0x00000000 /* Normal Mode */ 100 #define CONFIG_SYS_SDRC_TR_VAL 0x000002E0 /* Write refresh rate */ 101 #endif /* CONFIG_SKIP_LOWLEVEL_INIT */ 102 103 /* 104 * Hardware drivers 105 */ 106 /* 107 * Choose a USART for serial console 108 * CONFIG_DBGU is DBGU unit on J10 109 * CONFIG_USART1 is USART1 on J14 110 */ 111 #define CONFIG_ATMEL_USART 112 #define CONFIG_USART_BASE ATMEL_BASE_DBGU 113 #define CONFIG_USART_ID 0/* ignored in arm */ 114 115 #define CONFIG_BAUDRATE 115200 116 117 /* 118 * Command line configuration. 119 */ 120 121 /* 122 * Network Driver Setting 123 */ 124 #define CONFIG_DRIVER_AT91EMAC 125 #define CONFIG_SYS_RX_ETH_BUFFER 16 126 #define CONFIG_RMII 127 #define CONFIG_MII 128 129 /* 130 * NOR Flash 131 */ 132 #define CONFIG_FLASH_CFI_DRIVER 133 #define CONFIG_SYS_FLASH_CFI 134 #define CONFIG_SYS_FLASH_BASE 0x10000000 135 #define PHYS_FLASH_1 CONFIG_SYS_FLASH_BASE 136 #define PHYS_FLASH_SIZE SZ_8M 137 #define CONFIG_SYS_MAX_FLASH_BANKS 1 138 #define CONFIG_SYS_MAX_FLASH_SECT 256 139 #define CONFIG_SYS_FLASH_PROTECTION 140 141 /* 142 * USB Config 143 */ 144 #define CONFIG_USB_ATMEL 1 145 #define CONFIG_USB_ATMEL_CLK_SEL_PLLB 146 #define CONFIG_USB_OHCI_NEW 1 147 #define CONFIG_USB_KEYBOARD 1 148 #define CONFIG_DOS_PARTITION 1 149 150 #define CONFIG_SYS_USB_OHCI_CPU_INIT 1 151 #define CONFIG_SYS_USB_OHCI_REGS_BASE ATMEL_USB_HOST_BASE 152 #define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91rm9200" 153 #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15 154 155 /* 156 * Environment Settings 157 */ 158 #define CONFIG_ENV_IS_IN_FLASH 159 160 /* 161 * after u-boot.bin 162 */ 163 #define CONFIG_ENV_ADDR \ 164 (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN) 165 #define CONFIG_ENV_SIZE SZ_64K /* sectors are 64K here */ 166 /* The following #defines are needed to get flash environment right */ 167 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE 168 #define CONFIG_SYS_MONITOR_LEN SZ_256K 169 170 /* 171 * Boot option 172 */ 173 174 /* default load address */ 175 #define CONFIG_SYS_LOAD_ADDR CONFIG_SYS_SDRAM_BASE + SZ_16M 176 #define CONFIG_ENV_OVERWRITE 177 178 /* 179 * Shell Settings 180 */ 181 #define CONFIG_CMDLINE_EDITING 182 #define CONFIG_SYS_LONGHELP 183 #define CONFIG_AUTO_COMPLETE 184 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 185 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 186 /* Print Buffer Size */ 187 #define CONFIG_SYS_PBSIZE \ 188 (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) 189 190 /* 191 * Size of malloc() pool 192 */ 193 #define CONFIG_SYS_MALLOC_LEN ROUND(3 * CONFIG_ENV_SIZE + SZ_128K, \ 194 SZ_4K) 195 196 #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + SZ_4K \ 197 - GENERATED_GBL_DATA_SIZE) 198 199 #endif /* __AT91RM9200EK_CONFIG_H__ */ 200