1 /* 2 * Copyright (C) 2010 Andreas Bießmann <biessmann.devel@googlemail.com> 3 * 4 * based on previous work by 5 * 6 * Ulf Samuelsson <ulf@atmel.com> 7 * Rick Bronson <rick@efn.org> 8 * 9 * Configuration settings for the AT91RM9200EK board. 10 * 11 * SPDX-License-Identifier: GPL-2.0+ 12 */ 13 14 #ifndef __AT91RM9200EK_CONFIG_H__ 15 #define __AT91RM9200EK_CONFIG_H__ 16 17 #include <linux/sizes.h> 18 19 /* 20 * set some initial configurations depending on configure target 21 * 22 * at91rm9200ek_config -> boot from 0x0 in NOR Flash at CS0 23 * at91rm9200ek_ram_config -> continue booting from 0x20100000 in RAM; lowlevel 24 * initialisation was done by some preloader 25 */ 26 #ifdef CONFIG_RAMBOOT 27 #define CONFIG_SKIP_LOWLEVEL_INIT 28 #define CONFIG_SYS_TEXT_BASE 0x20100000 29 #else 30 #define CONFIG_SYS_TEXT_BASE 0x10000000 31 #endif 32 33 /* 34 * AT91C_XTAL_CLOCK is the frequency of external xtal in hertz 35 * AT91C_MAIN_CLOCK is the frequency of PLLA output 36 * AT91C_MASTER_CLOCK is the peripherial clock 37 * CONFIG_SYS_HZ_CLOCK is the value for CCR in tc0 (divider 2 is implicitely 38 * set in arch/arm/cpu/arm920t/at91/timer.c) 39 * CONFIG_SYS_HZ is the tick rate for timer tc0 40 */ 41 #define AT91C_XTAL_CLOCK 18432000 42 #define CONFIG_SYS_AT91_SLOW_CLOCK 32768 43 #define AT91C_MAIN_CLOCK ((AT91C_XTAL_CLOCK / 4) * 39) 44 #define AT91C_MASTER_CLOCK (AT91C_MAIN_CLOCK / 3 ) 45 #define CONFIG_SYS_HZ_CLOCK (AT91C_MASTER_CLOCK / 2) 46 47 /* CPU configuration */ 48 #define CONFIG_AT91RM9200 49 #define CONFIG_AT91RM9200EK 50 #define CONFIG_CPUAT91 51 #define USE_920T_MMU 52 53 #include <asm/hardware.h> /* needed for port definitions */ 54 55 #define CONFIG_CMDLINE_TAG 56 #define CONFIG_SETUP_MEMORY_TAGS 57 #define CONFIG_INITRD_TAG 58 59 #define CONFIG_BOARD_EARLY_INIT_F 60 61 #define CONFIG_CMD_BOOTZ 62 #define CONFIG_OF_LIBFDT 63 64 #define CONFIG_SYS_GENERIC_BOARD 65 66 /* 67 * Memory Configuration 68 */ 69 #define CONFIG_NR_DRAM_BANKS 1 70 #define CONFIG_SYS_SDRAM_BASE 0x20000000 71 #define CONFIG_SYS_SDRAM_SIZE SZ_32M 72 73 #define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE 74 #define CONFIG_SYS_MEMTEST_END \ 75 (CONFIG_SYS_MEMTEST_START + CONFIG_SYS_SDRAM_SIZE - SZ_256K) 76 77 /* 78 * LowLevel Init 79 */ 80 #ifndef CONFIG_SKIP_LOWLEVEL_INIT 81 #define CONFIG_SYS_USE_MAIN_OSCILLATOR 82 /* flash */ 83 #define CONFIG_SYS_EBI_CFGR_VAL 0x00000000 84 #define CONFIG_SYS_SMC_CSR0_VAL 0x00003284 /* 16bit, 2 TDF, 4 WS */ 85 86 /* clocks */ 87 #define CONFIG_SYS_PLLAR_VAL 0x20263E04 /* 179.712000 MHz for PCK */ 88 #define CONFIG_SYS_PLLBR_VAL 0x10483E0E /* 48.054857 MHz (divider by 2 for USB) */ 89 /* PCK/3 = MCK Master Clock = 59.904000MHz from PLLA */ 90 #define CONFIG_SYS_MCKR_VAL 0x00000202 91 92 /* sdram */ 93 #define CONFIG_SYS_PIOC_ASR_VAL 0xFFFF0000 /* Configure PIOC as peripheral (D16/D31) */ 94 #define CONFIG_SYS_PIOC_BSR_VAL 0x00000000 95 #define CONFIG_SYS_PIOC_PDR_VAL 0xFFFF0000 96 #define CONFIG_SYS_EBI_CSA_VAL 0x00000002 /* CS1=CONFIG_SYS_SDRAM */ 97 #define CONFIG_SYS_SDRC_CR_VAL 0x2188c155 /* set up the CONFIG_SYS_SDRAM */ 98 #define CONFIG_SYS_SDRAM CONFIG_SYS_SDRAM_BASE /* address of the SDRAM */ 99 #define CONFIG_SYS_SDRAM1 (CONFIG_SYS_SDRAM_BASE+0x80) 100 #define CONFIG_SYS_SDRAM_VAL 0x00000000 /* value written to CONFIG_SYS_SDRAM */ 101 #define CONFIG_SYS_SDRC_MR_VAL 0x00000002 /* Precharge All */ 102 #define CONFIG_SYS_SDRC_MR_VAL1 0x00000004 /* refresh */ 103 #define CONFIG_SYS_SDRC_MR_VAL2 0x00000003 /* Load Mode Register */ 104 #define CONFIG_SYS_SDRC_MR_VAL3 0x00000000 /* Normal Mode */ 105 #define CONFIG_SYS_SDRC_TR_VAL 0x000002E0 /* Write refresh rate */ 106 #endif /* CONFIG_SKIP_LOWLEVEL_INIT */ 107 108 /* 109 * Hardware drivers 110 */ 111 /* 112 * Choose a USART for serial console 113 * CONFIG_DBGU is DBGU unit on J10 114 * CONFIG_USART1 is USART1 on J14 115 */ 116 #define CONFIG_ATMEL_USART 117 #define CONFIG_USART_BASE ATMEL_BASE_DBGU 118 #define CONFIG_USART_ID 0/* ignored in arm */ 119 120 #define CONFIG_BAUDRATE 115200 121 122 /* 123 * Command line configuration. 124 */ 125 #include <config_cmd_default.h> 126 127 #define CONFIG_CMD_DHCP 128 #define CONFIG_CMD_FAT 129 #define CONFIG_CMD_MII 130 #define CONFIG_CMD_PING 131 #define CONFIG_CMD_USB 132 #undef CONFIG_CMD_FPGA 133 134 /* 135 * Network Driver Setting 136 */ 137 #define CONFIG_DRIVER_AT91EMAC 138 #define CONFIG_SYS_RX_ETH_BUFFER 16 139 #define CONFIG_RMII 140 #define CONFIG_MII 141 142 /* 143 * NOR Flash 144 */ 145 #define CONFIG_FLASH_CFI_DRIVER 146 #define CONFIG_SYS_FLASH_CFI 147 #define CONFIG_SYS_FLASH_BASE 0x10000000 148 #define PHYS_FLASH_1 CONFIG_SYS_FLASH_BASE 149 #define PHYS_FLASH_SIZE SZ_8M 150 #define CONFIG_SYS_MAX_FLASH_BANKS 1 151 #define CONFIG_SYS_MAX_FLASH_SECT 256 152 #define CONFIG_SYS_FLASH_PROTECTION 153 154 /* 155 * USB Config 156 */ 157 #define CONFIG_USB_ATMEL 1 158 #define CONFIG_USB_ATMEL_CLK_SEL_PLLB 159 #define CONFIG_USB_OHCI_NEW 1 160 #define CONFIG_USB_KEYBOARD 1 161 #define CONFIG_USB_STORAGE 1 162 #define CONFIG_DOS_PARTITION 1 163 164 #define CONFIG_SYS_USB_OHCI_CPU_INIT 1 165 #define CONFIG_SYS_USB_OHCI_REGS_BASE ATMEL_USB_HOST_BASE 166 #define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91rm9200" 167 #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15 168 169 /* 170 * Environment Settings 171 */ 172 #define CONFIG_ENV_IS_IN_FLASH 173 174 /* 175 * after u-boot.bin 176 */ 177 #define CONFIG_ENV_ADDR \ 178 (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN) 179 #define CONFIG_ENV_SIZE SZ_64K /* sectors are 64K here */ 180 /* The following #defines are needed to get flash environment right */ 181 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE 182 #define CONFIG_SYS_MONITOR_LEN SZ_256K 183 184 /* 185 * Boot option 186 */ 187 #define CONFIG_BOOTDELAY 3 188 189 /* default load address */ 190 #define CONFIG_SYS_LOAD_ADDR CONFIG_SYS_SDRAM_BASE + SZ_16M 191 #define CONFIG_ENV_OVERWRITE 192 193 /* 194 * Shell Settings 195 */ 196 #define CONFIG_CMDLINE_EDITING 197 #define CONFIG_SYS_LONGHELP 198 #define CONFIG_AUTO_COMPLETE 199 #define CONFIG_SYS_HUSH_PARSER 200 #define CONFIG_SYS_PROMPT "U-Boot> " 201 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 202 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 203 /* Print Buffer Size */ 204 #define CONFIG_SYS_PBSIZE \ 205 (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) 206 207 /* 208 * Size of malloc() pool 209 */ 210 #define CONFIG_SYS_MALLOC_LEN ROUND(3 * CONFIG_ENV_SIZE + SZ_128K, \ 211 SZ_4K) 212 213 #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + SZ_4K \ 214 - GENERATED_GBL_DATA_SIZE) 215 216 #endif /* __AT91RM9200EK_CONFIG_H__ */ 217