1 /* 2 * Copyright (C) 2010 Andreas Bießmann <biessmann.devel@googlemail.com> 3 * 4 * based on previous work by 5 * 6 * Ulf Samuelsson <ulf@atmel.com> 7 * Rick Bronson <rick@efn.org> 8 * 9 * Configuration settings for the AT91RM9200EK board. 10 * 11 * SPDX-License-Identifier: GPL-2.0+ 12 */ 13 14 #ifndef __AT91RM9200EK_CONFIG_H__ 15 #define __AT91RM9200EK_CONFIG_H__ 16 17 #include <linux/sizes.h> 18 19 /* 20 * set some initial configurations depending on configure target 21 * 22 * at91rm9200ek_config -> boot from 0x0 in NOR Flash at CS0 23 * at91rm9200ek_ram_config -> continue booting from 0x20100000 in RAM; lowlevel 24 * initialisation was done by some preloader 25 */ 26 #ifdef CONFIG_RAMBOOT 27 #define CONFIG_SKIP_LOWLEVEL_INIT 28 #define CONFIG_SYS_TEXT_BASE 0x20100000 29 #else 30 #define CONFIG_SYS_TEXT_BASE 0x10000000 31 #endif 32 33 /* 34 * AT91C_XTAL_CLOCK is the frequency of external xtal in hertz 35 * AT91C_MAIN_CLOCK is the frequency of PLLA output 36 * AT91C_MASTER_CLOCK is the peripherial clock 37 * CONFIG_SYS_HZ_CLOCK is the value for CCR in tc0 (divider 2 is implicitely 38 * set in arch/arm/cpu/arm920t/at91/timer.c) 39 * CONFIG_SYS_HZ is the tick rate for timer tc0 40 */ 41 #define AT91C_XTAL_CLOCK 18432000 42 #define CONFIG_SYS_AT91_SLOW_CLOCK 32768 43 #define AT91C_MAIN_CLOCK ((AT91C_XTAL_CLOCK / 4) * 39) 44 #define AT91C_MASTER_CLOCK (AT91C_MAIN_CLOCK / 3 ) 45 #define CONFIG_SYS_HZ_CLOCK (AT91C_MASTER_CLOCK / 2) 46 47 /* CPU configuration */ 48 #define CONFIG_AT91RM9200 49 #define CONFIG_AT91RM9200EK 50 #define CONFIG_CPUAT91 51 #define USE_920T_MMU 52 53 #include <asm/hardware.h> /* needed for port definitions */ 54 55 #define CONFIG_CMDLINE_TAG 56 #define CONFIG_SETUP_MEMORY_TAGS 57 #define CONFIG_INITRD_TAG 58 59 /* 60 * Memory Configuration 61 */ 62 #define CONFIG_NR_DRAM_BANKS 1 63 #define CONFIG_SYS_SDRAM_BASE 0x20000000 64 #define CONFIG_SYS_SDRAM_SIZE SZ_32M 65 66 #define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE 67 #define CONFIG_SYS_MEMTEST_END \ 68 (CONFIG_SYS_MEMTEST_START + CONFIG_SYS_SDRAM_SIZE - SZ_256K) 69 70 /* 71 * LowLevel Init 72 */ 73 #ifndef CONFIG_SKIP_LOWLEVEL_INIT 74 #define CONFIG_SYS_USE_MAIN_OSCILLATOR 75 /* flash */ 76 #define CONFIG_SYS_EBI_CFGR_VAL 0x00000000 77 #define CONFIG_SYS_SMC_CSR0_VAL 0x00003284 /* 16bit, 2 TDF, 4 WS */ 78 79 /* clocks */ 80 #define CONFIG_SYS_PLLAR_VAL 0x20263E04 /* 179.712000 MHz for PCK */ 81 #define CONFIG_SYS_PLLBR_VAL 0x10483E0E /* 48.054857 MHz (divider by 2 for USB) */ 82 /* PCK/3 = MCK Master Clock = 59.904000MHz from PLLA */ 83 #define CONFIG_SYS_MCKR_VAL 0x00000202 84 85 /* sdram */ 86 #define CONFIG_SYS_PIOC_ASR_VAL 0xFFFF0000 /* Configure PIOC as peripheral (D16/D31) */ 87 #define CONFIG_SYS_PIOC_BSR_VAL 0x00000000 88 #define CONFIG_SYS_PIOC_PDR_VAL 0xFFFF0000 89 #define CONFIG_SYS_EBI_CSA_VAL 0x00000002 /* CS1=CONFIG_SYS_SDRAM */ 90 #define CONFIG_SYS_SDRC_CR_VAL 0x2188c155 /* set up the CONFIG_SYS_SDRAM */ 91 #define CONFIG_SYS_SDRAM CONFIG_SYS_SDRAM_BASE /* address of the SDRAM */ 92 #define CONFIG_SYS_SDRAM1 (CONFIG_SYS_SDRAM_BASE+0x80) 93 #define CONFIG_SYS_SDRAM_VAL 0x00000000 /* value written to CONFIG_SYS_SDRAM */ 94 #define CONFIG_SYS_SDRC_MR_VAL 0x00000002 /* Precharge All */ 95 #define CONFIG_SYS_SDRC_MR_VAL1 0x00000004 /* refresh */ 96 #define CONFIG_SYS_SDRC_MR_VAL2 0x00000003 /* Load Mode Register */ 97 #define CONFIG_SYS_SDRC_MR_VAL3 0x00000000 /* Normal Mode */ 98 #define CONFIG_SYS_SDRC_TR_VAL 0x000002E0 /* Write refresh rate */ 99 #endif /* CONFIG_SKIP_LOWLEVEL_INIT */ 100 101 /* 102 * Hardware drivers 103 */ 104 /* 105 * Choose a USART for serial console 106 * CONFIG_DBGU is DBGU unit on J10 107 * CONFIG_USART1 is USART1 on J14 108 */ 109 #define CONFIG_ATMEL_USART 110 #define CONFIG_USART_BASE ATMEL_BASE_DBGU 111 #define CONFIG_USART_ID 0/* ignored in arm */ 112 113 /* 114 * Command line configuration. 115 */ 116 117 /* 118 * Network Driver Setting 119 */ 120 #define CONFIG_DRIVER_AT91EMAC 121 #define CONFIG_SYS_RX_ETH_BUFFER 16 122 #define CONFIG_RMII 123 #define CONFIG_MII 124 125 /* 126 * NOR Flash 127 */ 128 #define CONFIG_FLASH_CFI_DRIVER 129 #define CONFIG_SYS_FLASH_CFI 130 #define CONFIG_SYS_FLASH_BASE 0x10000000 131 #define PHYS_FLASH_1 CONFIG_SYS_FLASH_BASE 132 #define PHYS_FLASH_SIZE SZ_8M 133 #define CONFIG_SYS_MAX_FLASH_BANKS 1 134 #define CONFIG_SYS_MAX_FLASH_SECT 256 135 #define CONFIG_SYS_FLASH_PROTECTION 136 137 /* 138 * USB Config 139 */ 140 #define CONFIG_USB_ATMEL 1 141 #define CONFIG_USB_ATMEL_CLK_SEL_PLLB 142 #define CONFIG_USB_OHCI_NEW 1 143 144 #define CONFIG_SYS_USB_OHCI_CPU_INIT 1 145 #define CONFIG_SYS_USB_OHCI_REGS_BASE ATMEL_USB_HOST_BASE 146 #define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91rm9200" 147 #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15 148 149 /* 150 * Environment Settings 151 */ 152 #define CONFIG_ENV_IS_IN_FLASH 153 154 /* 155 * after u-boot.bin 156 */ 157 #define CONFIG_ENV_ADDR \ 158 (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN) 159 #define CONFIG_ENV_SIZE SZ_64K /* sectors are 64K here */ 160 /* The following #defines are needed to get flash environment right */ 161 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE 162 #define CONFIG_SYS_MONITOR_LEN SZ_256K 163 164 /* 165 * Boot option 166 */ 167 168 /* default load address */ 169 #define CONFIG_SYS_LOAD_ADDR CONFIG_SYS_SDRAM_BASE + SZ_16M 170 #define CONFIG_ENV_OVERWRITE 171 172 /* 173 * Shell Settings 174 */ 175 #define CONFIG_CMDLINE_EDITING 176 #define CONFIG_SYS_LONGHELP 177 #define CONFIG_AUTO_COMPLETE 178 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 179 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 180 /* Print Buffer Size */ 181 #define CONFIG_SYS_PBSIZE \ 182 (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) 183 184 /* 185 * Size of malloc() pool 186 */ 187 #define CONFIG_SYS_MALLOC_LEN ROUND(3 * CONFIG_ENV_SIZE + SZ_128K, \ 188 SZ_4K) 189 190 #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + SZ_4K \ 191 - GENERATED_GBL_DATA_SIZE) 192 193 #endif /* __AT91RM9200EK_CONFIG_H__ */ 194