1 /* SPDX-License-Identifier: GPL-2.0+ */ 2 /* 3 * Configuration settings for the Sentec Cobra Board. 4 * 5 * (C) Copyright 2003 Josef Baumgartner <josef.baumgartner@telex.de> 6 */ 7 8 /* 9 * configuration for ASTRO "Urmel" board. 10 * Originating from Cobra5272 configuration, messed up by 11 * Wolfgang Wegner <w.wegner@astro-kom.de> 12 * Please do not bother the original author with bug reports 13 * concerning this file. 14 */ 15 16 #ifndef _CONFIG_ASTRO_MCF5373L_H 17 #define _CONFIG_ASTRO_MCF5373L_H 18 19 #include <linux/stringify.h> 20 21 /* 22 * set the card type to actually compile for; either of 23 * the possibilities listed below has to be used! 24 */ 25 #define CONFIG_ASTRO_V532 1 26 27 #if CONFIG_ASTRO_V532 28 #define ASTRO_ID 0xF8 29 #elif CONFIG_ASTRO_V512 30 #define ASTRO_ID 0xFA 31 #elif CONFIG_ASTRO_TWIN7S2 32 #define ASTRO_ID 0xF9 33 #elif CONFIG_ASTRO_V912 34 #define ASTRO_ID 0xFC 35 #elif CONFIG_ASTRO_COFDMDUOS2 36 #define ASTRO_ID 0xFB 37 #else 38 #error No card type defined! 39 #endif 40 41 /* Command line configuration */ 42 /* 43 * CONFIG_RAM defines if u-boot is loaded via BDM (or started from 44 * a different bootloader that has already performed RAM setup) or 45 * started directly from flash, which is the regular case for production 46 * boards. 47 */ 48 #ifdef CONFIG_RAM 49 #define CONFIG_MONITOR_IS_IN_RAM 50 #define ENABLE_JFFS 0 51 #else 52 #define ENABLE_JFFS 1 53 #endif 54 55 #define CONFIG_MCFRTC 56 #undef RTC_DEBUG 57 58 /* Timer */ 59 #define CONFIG_MCFTMR 60 #undef CONFIG_MCFPIT 61 62 /* I2C */ 63 #define CONFIG_SYS_I2C 64 #define CONFIG_SYS_I2C_FSL 65 #define CONFIG_SYS_FSL_I2C_SPEED 80000 66 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 67 #define CONFIG_SYS_FSL_I2C_OFFSET 0x58000 68 #define CONFIG_SYS_IMMR CONFIG_SYS_MBAR 69 70 /* 71 * Defines processor clock - important for correct timings concerning serial 72 * interface etc. 73 */ 74 75 #define CONFIG_SYS_CLK 80000000 76 #define CONFIG_SYS_CPU_CLK (CONFIG_SYS_CLK * 3) 77 #define CONFIG_SYS_SDRAM_SIZE 32 /* SDRAM size in MB */ 78 79 #define CONFIG_SYS_CORE_SRAM_SIZE 0x8000 80 #define CONFIG_SYS_CORE_SRAM 0x80000000 81 82 #define CONFIG_SYS_UNIFY_CACHE 83 84 /* 85 * Define baudrate for UART1 (console output, tftp, ...) 86 * default value of CONFIG_BAUDRATE for Sentec board: 19200 baud 87 * CONFIG_SYS_BAUDRATE_TABLE defines values that can be selected 88 * in u-boot command interface 89 */ 90 91 #define CONFIG_MCFUART 92 #define CONFIG_SYS_UART_PORT (2) 93 #define CONFIG_SYS_UART2_ALT3_GPIO 94 95 /* 96 * Watchdog configuration; Watchdog is disabled for running from RAM 97 * and set to highest possible value else. Beware there is no check 98 * in the watchdog code to validate the timeout value set here! 99 */ 100 101 #ifndef CONFIG_MONITOR_IS_IN_RAM 102 #define CONFIG_WATCHDOG 103 #define CONFIG_WATCHDOG_TIMEOUT 3355 /* timeout in milliseconds */ 104 #endif 105 106 /* 107 * Configuration for environment 108 * Environment is located in the last sector of the flash 109 */ 110 111 #ifndef CONFIG_MONITOR_IS_IN_RAM 112 #define CONFIG_ENV_OFFSET 0x1FF8000 113 #define CONFIG_ENV_SECT_SIZE 0x8000 114 #else 115 /* 116 * environment in RAM - This is used to use a single PC-based application 117 * to load an image, load U-Boot, load an environment and then start U-Boot 118 * to execute the commands from the environment. Feedback is done via setting 119 * and reading memory locations. 120 */ 121 #define CONFIG_ENV_ADDR 0x40060000 122 #define CONFIG_ENV_SECT_SIZE 0x8000 123 #endif 124 125 /* here we put our FPGA configuration... */ 126 127 /* Define user parameters that have to be customized most likely */ 128 129 /* AUTOBOOT settings - booting images automatically by u-boot after power on */ 130 131 /* 132 * The following settings will be contained in the environment block ; if you 133 * want to use a neutral environment all those settings can be manually set in 134 * u-boot: 'set' command 135 */ 136 137 #define CONFIG_EXTRA_ENV_SETTINGS \ 138 "loaderversion=11\0" \ 139 "card_id="__stringify(ASTRO_ID)"\0" \ 140 "alterafile=0\0" \ 141 "xilinxfile=0\0" \ 142 "xilinxload=imxtract 0x540000 $xilinxfile 0x41000000&&"\ 143 "fpga load 0 0x41000000 $filesize\0" \ 144 "alteraload=imxtract 0x6c0000 $alterafile 0x41000000&&"\ 145 "fpga load 1 0x41000000 $filesize\0" \ 146 "env_default=1\0" \ 147 "env_check=if test $env_default -eq 1;"\ 148 " then setenv env_default 0;saveenv;fi\0" 149 150 /* 151 * "update" is a non-standard command that has to be supplied 152 * by external update.c; This is not included in mainline because 153 * it needs non-blocking CFI routines. 154 */ 155 #ifdef CONFIG_MONITOR_IS_IN_RAM 156 #define CONFIG_BOOTCOMMAND "" /* no autoboot in this case */ 157 #else 158 #if CONFIG_ASTRO_V532 159 #define CONFIG_BOOTCOMMAND "protect off 0x80000 0x1ffffff;run env_check;"\ 160 "run xilinxload&&run alteraload&&bootm 0x80000;"\ 161 "update;reset" 162 #else 163 #define CONFIG_BOOTCOMMAND "protect off 0x80000 0x1ffffff;run env_check;"\ 164 "run xilinxload&&bootm 0x80000;update;reset" 165 #endif 166 #endif 167 168 /* default RAM address for user programs */ 169 #define CONFIG_SYS_LOAD_ADDR 0x20000 170 171 #define CONFIG_FPGA_COUNT 1 172 #define CONFIG_SYS_FPGA_PROG_FEEDBACK 173 #define CONFIG_SYS_FPGA_WAIT 1000 174 175 /* End of user parameters to be customized */ 176 177 /* Defines memory range for test */ 178 179 #define CONFIG_SYS_MEMTEST_START 0x40020000 180 #define CONFIG_SYS_MEMTEST_END 0x41ffffff 181 182 /* 183 * Low Level Configuration Settings 184 * (address mappings, register initial values, etc.) 185 * You should know what you are doing if you make changes here. 186 */ 187 188 /* Base register address */ 189 190 #define CONFIG_SYS_MBAR 0xFC000000 /* Register Base Addrs */ 191 192 /* System Conf. Reg. & System Protection Reg. */ 193 194 #define CONFIG_SYS_SCR 0x0003; 195 #define CONFIG_SYS_SPR 0xffff; 196 197 /* 198 * Definitions for initial stack pointer and data area (in internal SRAM) 199 */ 200 #define CONFIG_SYS_INIT_RAM_ADDR 0x80000000 201 #define CONFIG_SYS_INIT_RAM_SIZE 0x8000 202 #define CONFIG_SYS_INIT_RAM_CTRL 0x221 203 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ 204 GENERATED_GBL_DATA_SIZE) 205 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 206 207 /* 208 * Start addresses for the final memory configuration 209 * (Set up by the startup code) 210 * for MCF5373, the allowable range is 0x40000000 to 0x7FF00000 211 */ 212 #define CONFIG_SYS_SDRAM_BASE 0x40000000 213 214 /* 215 * Chipselect bank definitions 216 * 217 * CS0 - Flash 32MB (first 16MB) 218 * CS1 - Flash 32MB (second half) 219 * CS2 - FPGA 220 * CS3 - FPGA 221 * CS4 - unused 222 * CS5 - unused 223 */ 224 #define CONFIG_SYS_CS0_BASE 0 225 #define CONFIG_SYS_CS0_MASK 0x00ff0001 226 #define CONFIG_SYS_CS0_CTRL 0x00001fc0 227 228 #define CONFIG_SYS_CS1_BASE 0x01000000 229 #define CONFIG_SYS_CS1_MASK 0x00ff0001 230 #define CONFIG_SYS_CS1_CTRL 0x00001fc0 231 232 #define CONFIG_SYS_CS2_BASE 0x20000000 233 #define CONFIG_SYS_CS2_MASK 0x00ff0001 234 #define CONFIG_SYS_CS2_CTRL 0x0000fec0 235 236 #define CONFIG_SYS_CS3_BASE 0x21000000 237 #define CONFIG_SYS_CS3_MASK 0x00ff0001 238 #define CONFIG_SYS_CS3_CTRL 0x0000fec0 239 240 #define CONFIG_SYS_FLASH_BASE 0x00000000 241 242 #ifdef CONFIG_MONITOR_IS_IN_RAM 243 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE 244 #else 245 /* This is mainly used during relocation in start.S */ 246 #define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400) 247 #endif 248 /* Reserve 256 kB for Monitor */ 249 #define CONFIG_SYS_MONITOR_LEN (256 << 10) 250 251 #define CONFIG_SYS_BOOTPARAMS_LEN (64 * 1024) 252 /* Reserve 128 kB for malloc() */ 253 #define CONFIG_SYS_MALLOC_LEN (128 << 10) 254 255 /* 256 * For booting Linux, the board info and command line data 257 * have to be in the first 8 MB of memory, since this is 258 * the maximum mapped by the Linux kernel during initialization ?? 259 */ 260 #define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + \ 261 (CONFIG_SYS_SDRAM_SIZE << 20)) 262 263 /* FLASH organization */ 264 #define CONFIG_SYS_MAX_FLASH_BANKS 1 265 #define CONFIG_SYS_MAX_FLASH_SECT 259 266 #define CONFIG_SYS_FLASH_ERASE_TOUT 1000 267 268 #define CONFIG_SYS_FLASH_SIZE 0x2000000 269 #define CONFIG_SYS_FLASH_CFI_NONBLOCK 1 270 271 #define LDS_BOARD_TEXT \ 272 . = DEFINED(env_offset) ? env_offset : .; \ 273 env/embedded.o(.text*) 274 275 #if ENABLE_JFFS 276 /* JFFS Partition offset set */ 277 #define CONFIG_SYS_JFFS2_FIRST_BANK 0 278 #define CONFIG_SYS_JFFS2_NUM_BANKS 1 279 /* 512k reserved for u-boot */ 280 #define CONFIG_SYS_JFFS2_FIRST_SECTOR 0x40 281 #endif 282 283 /* Cache Configuration */ 284 #define CONFIG_SYS_CACHELINE_SIZE 16 285 286 #define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ 287 CONFIG_SYS_INIT_RAM_SIZE - 8) 288 #define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ 289 CONFIG_SYS_INIT_RAM_SIZE - 4) 290 #define CONFIG_SYS_ICACHE_INV (CF_CACR_CINVA) 291 #define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_SDRAM_BASE | \ 292 CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ 293 CF_ACR_EN | CF_ACR_SM_ALL) 294 #define CONFIG_SYS_CACHE_ICACR (CF_CACR_EC | CF_CACR_CINVA | \ 295 CF_CACR_DCM_P) 296 297 #endif /* _CONFIG_ASTRO_MCF5373L_H */ 298