1 /* 2 * Configuation settings for the Renesas Solutions AP-325RXA board 3 * 4 * Copyright (C) 2008 Renesas Solutions Corp. 5 * Copyright (C) 2008 Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com> 6 * 7 * SPDX-License-Identifier: GPL-2.0+ 8 */ 9 10 #ifndef __AP325RXA_H 11 #define __AP325RXA_H 12 13 #define CONFIG_CPU_SH7723 1 14 #define CONFIG_AP325RXA 1 15 16 #define CONFIG_CMD_SDRAM 17 18 #define CONFIG_BOOTARGS "console=ttySC2,38400" 19 20 #define CONFIG_DISPLAY_BOARDINFO 21 #undef CONFIG_SHOW_BOOT_PROGRESS 22 23 /* SMC9118 */ 24 #define CONFIG_SMC911X 1 25 #define CONFIG_SMC911X_32_BIT 1 26 #define CONFIG_SMC911X_BASE 0xB6080000 27 28 /* MEMORY */ 29 #define AP325RXA_SDRAM_BASE (0x88000000) 30 #define AP325RXA_FLASH_BASE_1 (0xA0000000) 31 #define AP325RXA_FLASH_BANK_SIZE (128 * 1024 * 1024) 32 33 #define CONFIG_SYS_TEXT_BASE 0x8FFC0000 34 35 /* undef to save memory */ 36 #define CONFIG_SYS_LONGHELP 37 /* Monitor Command Prompt */ 38 /* Buffer size for input from the Console */ 39 #define CONFIG_SYS_CBSIZE 256 40 /* Buffer size for Console output */ 41 #define CONFIG_SYS_PBSIZE 256 42 /* max args accepted for monitor commands */ 43 #define CONFIG_SYS_MAXARGS 16 44 /* Buffer size for Boot Arguments passed to kernel */ 45 #define CONFIG_SYS_BARGSIZE 512 46 /* List of legal baudrate settings for this board */ 47 #define CONFIG_SYS_BAUDRATE_TABLE { 38400 } 48 49 /* SCIF */ 50 #define CONFIG_SCIF_A 1 /* SH7723 has SCIF and SCIFA */ 51 #define CONFIG_CONS_SCIF5 1 52 53 /* Suppress display of console information at boot */ 54 55 #define CONFIG_SYS_MEMTEST_START (AP325RXA_SDRAM_BASE) 56 #define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + (60 * 1024 * 1024)) 57 58 /* Enable alternate, more extensive, memory test */ 59 #undef CONFIG_SYS_ALT_MEMTEST 60 /* Scratch address used by the alternate memory test */ 61 #undef CONFIG_SYS_MEMTEST_SCRATCH 62 63 /* Enable temporary baudrate change while serial download */ 64 #undef CONFIG_SYS_LOADS_BAUD_CHANGE 65 66 #define CONFIG_SYS_SDRAM_BASE (AP325RXA_SDRAM_BASE) 67 /* maybe more, but if so u-boot doesn't know about it... */ 68 #define CONFIG_SYS_SDRAM_SIZE (128 * 1024 * 1024) 69 /* default load address for scripts ?!? */ 70 #define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 16 * 1024 * 1024) 71 72 /* Address of u-boot image in Flash (NOT run time address in SDRAM) ?!? */ 73 #define CONFIG_SYS_MONITOR_BASE (AP325RXA_FLASH_BASE_1) 74 /* Monitor size */ 75 #define CONFIG_SYS_MONITOR_LEN (128 * 1024) 76 /* Size of DRAM reserved for malloc() use */ 77 #define CONFIG_SYS_MALLOC_LEN (256 * 1024) 78 #define CONFIG_SYS_BOOTMAPSZ (8 * 1024 * 1024) 79 80 /* FLASH */ 81 #define CONFIG_FLASH_CFI_DRIVER 1 82 #define CONFIG_SYS_FLASH_CFI 83 #undef CONFIG_SYS_FLASH_QUIET_TEST 84 /* print 'E' for empty sector on flinfo */ 85 #define CONFIG_SYS_FLASH_EMPTY_INFO 86 /* Physical start address of Flash memory */ 87 #define CONFIG_SYS_FLASH_BASE (AP325RXA_FLASH_BASE_1) 88 /* Max number of sectors on each Flash chip */ 89 #define CONFIG_SYS_MAX_FLASH_SECT 512 90 91 /* 92 * IDE support 93 */ 94 #define CONFIG_IDE_RESET 1 95 #define CONFIG_SYS_PIO_MODE 1 96 #define CONFIG_SYS_IDE_MAXBUS 1 /* IDE bus */ 97 #define CONFIG_SYS_IDE_MAXDEVICE 1 98 #define CONFIG_SYS_ATA_BASE_ADDR 0xB4180000 99 #define CONFIG_SYS_ATA_STRIDE 2 /* 1bit shift */ 100 #define CONFIG_SYS_ATA_DATA_OFFSET 0x200 /* data reg offset */ 101 #define CONFIG_SYS_ATA_REG_OFFSET 0x200 /* reg offset */ 102 #define CONFIG_SYS_ATA_ALT_OFFSET 0x210 /* alternate register offset */ 103 #define CONFIG_IDE_SWAP_IO 104 105 /* if you use all NOR Flash , you change dip-switch. Please see Manual. */ 106 #define CONFIG_SYS_MAX_FLASH_BANKS 1 107 #define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE + (0 * AP325RXA_FLASH_BANK_SIZE)} 108 109 /* Timeout for Flash erase operations (in ms) */ 110 #define CONFIG_SYS_FLASH_ERASE_TOUT (3 * 1000) 111 /* Timeout for Flash write operations (in ms) */ 112 #define CONFIG_SYS_FLASH_WRITE_TOUT (3 * 1000) 113 /* Timeout for Flash set sector lock bit operations (in ms) */ 114 #define CONFIG_SYS_FLASH_LOCK_TOUT (3 * 1000) 115 /* Timeout for Flash clear lock bit operations (in ms) */ 116 #define CONFIG_SYS_FLASH_UNLOCK_TOUT (3 * 1000) 117 118 /* 119 * Use hardware flash sectors protection instead 120 * of U-Boot software protection 121 */ 122 #undef CONFIG_SYS_FLASH_PROTECTION 123 #undef CONFIG_SYS_DIRECT_FLASH_TFTP 124 125 /* ENV setting */ 126 #define CONFIG_ENV_OVERWRITE 1 127 #define CONFIG_ENV_SECT_SIZE (128 * 1024) 128 #define CONFIG_ENV_SIZE (CONFIG_ENV_SECT_SIZE) 129 #define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN) 130 /* Offset of env Flash sector relative to CONFIG_SYS_FLASH_BASE */ 131 #define CONFIG_ENV_OFFSET (CONFIG_ENV_ADDR - CONFIG_SYS_FLASH_BASE) 132 #define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SECT_SIZE) 133 134 /* Board Clock */ 135 #define CONFIG_SYS_CLK_FREQ 33333333 136 #define CONFIG_SH_TMU_CLK_FREQ CONFIG_SYS_CLK_FREQ 137 #define CONFIG_SH_SCIF_CLK_FREQ CONFIG_SYS_CLK_FREQ 138 #define CONFIG_SYS_TMU_CLK_DIV (4) /* 4 (default), 16, 64, 256 or 1024 */ 139 140 #endif /* __AP325RXA_H */ 141