1 /* 2 * Copyright (C) 2016 Timesys Corporation 3 * Copyright (C) 2016 Advantech Corporation 4 * Copyright (C) 2012 Freescale Semiconductor, Inc. 5 * 6 * SPDX-License-Identifier: GPL-2.0+ 7 */ 8 9 #ifndef __ADVANTECH_DMSBA16_CONFIG_H 10 #define __ADVANTECH_DMSBA16_CONFIG_H 11 12 #include <asm/arch/imx-regs.h> 13 #include <asm/imx-common/gpio.h> 14 15 #define CONFIG_BOARD_NAME "Advantech DMS-BA16" 16 17 #define CONFIG_MXC_UART_BASE UART4_BASE 18 #define CONSOLE_DEV "ttymxc3" 19 #define CONFIG_EXTRA_BOOTARGS "panic=10" 20 21 #define CONFIG_BOOT_DIR "" 22 #define CONFIG_LOADCMD "fatload" 23 #define CONFIG_RFSPART "2" 24 25 #define CONFIG_SUPPORT_EMMC_BOOT 26 27 #include "mx6_common.h" 28 #include <linux/sizes.h> 29 30 #define CONFIG_CMDLINE_TAG 31 #define CONFIG_SETUP_MEMORY_TAGS 32 #define CONFIG_INITRD_TAG 33 #define CONFIG_REVISION_TAG 34 #define CONFIG_SYS_MALLOC_LEN (10 * SZ_1M) 35 36 #define CONFIG_BOARD_EARLY_INIT_F 37 #define CONFIG_BOARD_LATE_INIT 38 39 #define CONFIG_MXC_GPIO 40 #define CONFIG_MXC_UART 41 42 #define CONFIG_CMD_FUSE 43 #define CONFIG_MXC_OCOTP 44 45 /* SATA Configs */ 46 #define CONFIG_CMD_SATA 47 #define CONFIG_DWC_AHSATA 48 #define CONFIG_SYS_SATA_MAX_DEVICE 1 49 #define CONFIG_DWC_AHSATA_PORT_ID 0 50 #define CONFIG_DWC_AHSATA_BASE_ADDR SATA_ARB_BASE_ADDR 51 #define CONFIG_LBA48 52 #define CONFIG_LIBATA 53 54 /* MMC Configs */ 55 #define CONFIG_FSL_ESDHC 56 #define CONFIG_FSL_USDHC 57 #define CONFIG_SYS_FSL_ESDHC_ADDR 0 58 #define CONFIG_MMC 59 #define CONFIG_GENERIC_MMC 60 #define CONFIG_BOUNCE_BUFFER 61 #define CONFIG_DOS_PARTITION 62 63 /* USB Configs */ 64 #define CONFIG_USB_EHCI 65 #define CONFIG_USB_EHCI_MX6 66 #define CONFIG_USB_STORAGE 67 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2 68 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET 69 #define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW) 70 #define CONFIG_MXC_USB_FLAGS 0 71 #define CONFIG_SYS_USB_EVENT_POLL_VIA_CONTROL_EP 72 73 #define CONFIG_USBD_HS 74 #define CONFIG_USB_FUNCTION_MASS_STORAGE 75 #define CONFIG_USB_GADGET_VBUS_DRAW 2 76 77 /* Networking Configs */ 78 #define CONFIG_FEC_MXC 79 #define CONFIG_MII 80 #define IMX_FEC_BASE ENET_BASE_ADDR 81 #define CONFIG_FEC_XCV_TYPE RGMII 82 #define CONFIG_ETHPRIME "FEC" 83 #define CONFIG_FEC_MXC_PHYADDR 4 84 #define CONFIG_PHYLIB 85 #define CONFIG_PHY_ATHEROS 86 87 /* Serial Flash */ 88 #ifdef CONFIG_CMD_SF 89 #define CONFIG_MXC_SPI 90 #define CONFIG_SF_DEFAULT_BUS 0 91 #define CONFIG_SF_DEFAULT_CS 0 92 #define CONFIG_SF_DEFAULT_SPEED 20000000 93 #define CONFIG_SF_DEFAULT_MODE SPI_MODE_0 94 #endif 95 96 /* allow to overwrite serial and ethaddr */ 97 #define CONFIG_ENV_OVERWRITE 98 #define CONFIG_CONS_INDEX 1 99 #define CONFIG_BAUDRATE 115200 100 101 /* Command definition */ 102 #define CONFIG_CMD_BMODE 103 104 #define CONFIG_LOADADDR 0x12000000 105 #define CONFIG_SYS_TEXT_BASE 0x17800000 106 107 #define CONFIG_EXTRA_ENV_SETTINGS \ 108 "script=boot.scr\0" \ 109 "image=" CONFIG_BOOT_DIR "/uImage\0" \ 110 "uboot=u-boot.imx\0" \ 111 "fdt_file=" CONFIG_BOOT_DIR "/" CONFIG_DEFAULT_FDT_FILE "\0" \ 112 "fdt_addr=0x18000000\0" \ 113 "boot_fdt=yes\0" \ 114 "ip_dyn=yes\0" \ 115 "console=" CONSOLE_DEV "\0" \ 116 "fdt_high=0xffffffff\0" \ 117 "initrd_high=0xffffffff\0" \ 118 "sddev=0\0" \ 119 "emmcdev=1\0" \ 120 "partnum=1\0" \ 121 "loadcmd=" CONFIG_LOADCMD "\0" \ 122 "rfspart=" CONFIG_RFSPART "\0" \ 123 "update_sd_firmware=" \ 124 "if test ${ip_dyn} = yes; then " \ 125 "setenv get_cmd dhcp; " \ 126 "else " \ 127 "setenv get_cmd tftp; " \ 128 "fi; " \ 129 "if mmc dev ${mmcdev}; then " \ 130 "if ${get_cmd} ${update_sd_firmware_filename}; then " \ 131 "setexpr fw_sz ${filesize} / 0x200; " \ 132 "setexpr fw_sz ${fw_sz} + 1; " \ 133 "mmc write ${loadaddr} 0x2 ${fw_sz}; " \ 134 "fi; " \ 135 "fi\0" \ 136 "update_sf_uboot=" \ 137 "if tftp $loadaddr $uboot; then " \ 138 "sf probe; " \ 139 "sf erase 0 0xC0000; " \ 140 "sf write $loadaddr 0x400 $filesize; " \ 141 "echo 'U-Boot upgraded. Please reset'; " \ 142 "fi\0" \ 143 "setargs=setenv bootargs console=${console},${baudrate} " \ 144 "root=/dev/${rootdev} rw rootwait " CONFIG_EXTRA_BOOTARGS "\0" \ 145 "loadbootscript=" \ 146 "${loadcmd} ${dev} ${devnum}:${partnum} ${loadaddr} ${script};\0" \ 147 "bootscript=echo Running bootscript from ${dev}:${devnum}:${partnum};" \ 148 " source\0" \ 149 "loadimage=" \ 150 "${loadcmd} ${dev} ${devnum}:${partnum} ${loadaddr} ${image}\0" \ 151 "loadfdt=${loadcmd} ${dev} ${devnum}:${partnum} ${fdt_addr} ${fdt_file}\0" \ 152 "tryboot=" \ 153 "if run loadbootscript; then " \ 154 "run bootscript; " \ 155 "else " \ 156 "if run loadimage; then " \ 157 "run doboot; " \ 158 "fi; " \ 159 "fi;\0" \ 160 "doboot=echo Booting from ${dev}:${devnum}:${partnum} ...; " \ 161 "run setargs; " \ 162 "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ 163 "if run loadfdt; then " \ 164 "bootm ${loadaddr} - ${fdt_addr}; " \ 165 "else " \ 166 "if test ${boot_fdt} = try; then " \ 167 "bootm; " \ 168 "else " \ 169 "echo WARN: Cannot load the DT; " \ 170 "fi; " \ 171 "fi; " \ 172 "else " \ 173 "bootm; " \ 174 "fi;\0" \ 175 "netargs=setenv bootargs console=${console},${baudrate} " \ 176 "root=/dev/nfs " \ 177 "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \ 178 "netboot=echo Booting from net ...; " \ 179 "run netargs; " \ 180 "if test ${ip_dyn} = yes; then " \ 181 "setenv get_cmd dhcp; " \ 182 "else " \ 183 "setenv get_cmd tftp; " \ 184 "fi; " \ 185 "${get_cmd} ${image}; " \ 186 "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ 187 "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \ 188 "bootm ${loadaddr} - ${fdt_addr}; " \ 189 "else " \ 190 "if test ${boot_fdt} = try; then " \ 191 "bootm; " \ 192 "else " \ 193 "echo WARN: Cannot load the DT; " \ 194 "fi; " \ 195 "fi; " \ 196 "else " \ 197 "bootm; " \ 198 "fi;\0" \ 199 200 #define CONFIG_BOOTCOMMAND \ 201 "usb start; " \ 202 "setenv dev usb; " \ 203 "setenv devnum 0; " \ 204 "setenv rootdev sda${rfspart}; " \ 205 "run tryboot; " \ 206 \ 207 "setenv dev mmc; " \ 208 "setenv rootdev mmcblk0p${rfspart}; " \ 209 \ 210 "setenv devnum ${sddev}; " \ 211 "if mmc dev ${devnum}; then " \ 212 "run tryboot; " \ 213 "fi; " \ 214 \ 215 "setenv devnum ${emmcdev}; " \ 216 "setenv rootdev mmcblk${emmcdev}p${rfspart}; " \ 217 "if mmc dev ${devnum}; then " \ 218 "run tryboot; " \ 219 "fi; " \ 220 \ 221 "bmode usb; " \ 222 223 #define CONFIG_ARP_TIMEOUT 200UL 224 225 /* Miscellaneous configurable options */ 226 #define CONFIG_SYS_LONGHELP 227 #define CONFIG_AUTO_COMPLETE 228 229 /* Print Buffer Size */ 230 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) 231 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE 232 233 #define CONFIG_SYS_MEMTEST_START 0x10000000 234 #define CONFIG_SYS_MEMTEST_END 0x10010000 235 #define CONFIG_SYS_MEMTEST_SCRATCH 0x10800000 236 237 #define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR 238 239 #define CONFIG_CMDLINE_EDITING 240 #define CONFIG_STACKSIZE (128 * 1024) 241 242 /* Physical Memory Map */ 243 #define CONFIG_NR_DRAM_BANKS 1 244 #define PHYS_SDRAM MMDC0_ARB_BASE_ADDR 245 246 #define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM 247 #define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR 248 #define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE 249 250 #define CONFIG_SYS_INIT_SP_OFFSET \ 251 (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 252 #define CONFIG_SYS_INIT_SP_ADDR \ 253 (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) 254 255 /* FLASH and environment organization */ 256 #define CONFIG_SYS_NO_FLASH 257 258 #define CONFIG_ENV_IS_IN_SPI_FLASH 259 #define CONFIG_ENV_SIZE (8 * 1024) 260 #define CONFIG_ENV_OFFSET (768 * 1024) 261 #define CONFIG_ENV_SECT_SIZE (64 * 1024) 262 #define CONFIG_ENV_SPI_BUS CONFIG_SF_DEFAULT_BUS 263 #define CONFIG_ENV_SPI_CS CONFIG_SF_DEFAULT_CS 264 #define CONFIG_ENV_SPI_MODE CONFIG_SF_DEFAULT_MODE 265 #define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED 266 267 #ifndef CONFIG_SYS_DCACHE_OFF 268 #endif 269 270 #define CONFIG_SYS_FSL_USDHC_NUM 3 271 272 /* Framebuffer */ 273 #define CONFIG_VIDEO_IPUV3 274 #define CONFIG_VIDEO_BMP_RLE8 275 #define CONFIG_SPLASH_SCREEN 276 #define CONFIG_SPLASH_SCREEN_ALIGN 277 #define CONFIG_BMP_16BPP 278 #define CONFIG_VIDEO_LOGO 279 #define CONFIG_VIDEO_BMP_LOGO 280 #define CONFIG_IPUV3_CLK 260000000 281 #define CONFIG_IMX_HDMI 282 #define CONFIG_IMX_VIDEO_SKIP 283 284 #define CONFIG_PWM_IMX 285 #define CONFIG_IMX6_PWM_PER_CLK 66000000 286 287 #undef CONFIG_CMD_PCI 288 #ifdef CONFIG_CMD_PCI 289 #define CONFIG_PCI_SCAN_SHOW 290 #define CONFIG_PCIE_IMX 291 #define CONFIG_PCIE_IMX_PERST_GPIO IMX_GPIO_NR(7, 12) 292 #define CONFIG_PCIE_IMX_POWER_GPIO IMX_GPIO_NR(1, 5) 293 #endif 294 295 /* I2C Configs */ 296 #define CONFIG_SYS_I2C 297 #define CONFIG_SYS_I2C_MXC 298 #define CONFIG_SYS_I2C_SPEED 100000 299 #define CONFIG_SYS_I2C_MXC_I2C1 300 #define CONFIG_SYS_I2C_MXC_I2C2 301 #define CONFIG_SYS_I2C_MXC_I2C3 302 303 #endif /* __ADVANTECH_DMSBA16_CONFIG_H */ 304