1 /* 2 * Copyright (C) 2016 Timesys Corporation 3 * Copyright (C) 2016 Advantech Corporation 4 * Copyright (C) 2012 Freescale Semiconductor, Inc. 5 * 6 * SPDX-License-Identifier: GPL-2.0+ 7 */ 8 9 #ifndef __ADVANTECH_DMSBA16_CONFIG_H 10 #define __ADVANTECH_DMSBA16_CONFIG_H 11 12 #include <asm/arch/imx-regs.h> 13 #include <asm/imx-common/gpio.h> 14 15 #define CONFIG_BOARD_NAME "Advantech DMS-BA16" 16 17 #define CONFIG_MXC_UART_BASE UART4_BASE 18 #define CONSOLE_DEV "ttymxc3" 19 #define CONFIG_EXTRA_BOOTARGS "panic=10" 20 21 #define CONFIG_BOOT_DIR "" 22 #define CONFIG_LOADCMD "fatload" 23 #define CONFIG_RFSPART "2" 24 25 #define CONFIG_SUPPORT_EMMC_BOOT 26 27 #include "mx6_common.h" 28 #include <linux/sizes.h> 29 30 #define CONFIG_CMDLINE_TAG 31 #define CONFIG_SETUP_MEMORY_TAGS 32 #define CONFIG_INITRD_TAG 33 #define CONFIG_REVISION_TAG 34 #define CONFIG_SYS_MALLOC_LEN (10 * SZ_1M) 35 36 #define CONFIG_BOARD_EARLY_INIT_F 37 38 #define CONFIG_MXC_GPIO 39 #define CONFIG_MXC_UART 40 41 #define CONFIG_CMD_FUSE 42 #define CONFIG_MXC_OCOTP 43 44 /* SATA Configs */ 45 #define CONFIG_CMD_SATA 46 #define CONFIG_DWC_AHSATA 47 #define CONFIG_SYS_SATA_MAX_DEVICE 1 48 #define CONFIG_DWC_AHSATA_PORT_ID 0 49 #define CONFIG_DWC_AHSATA_BASE_ADDR SATA_ARB_BASE_ADDR 50 #define CONFIG_LBA48 51 #define CONFIG_LIBATA 52 53 /* MMC Configs */ 54 #define CONFIG_FSL_ESDHC 55 #define CONFIG_FSL_USDHC 56 #define CONFIG_SYS_FSL_ESDHC_ADDR 0 57 #define CONFIG_GENERIC_MMC 58 #define CONFIG_BOUNCE_BUFFER 59 #define CONFIG_DOS_PARTITION 60 61 /* USB Configs */ 62 #define CONFIG_USB_EHCI 63 #define CONFIG_USB_EHCI_MX6 64 #define CONFIG_USB_STORAGE 65 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2 66 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET 67 #define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW) 68 #define CONFIG_MXC_USB_FLAGS 0 69 #define CONFIG_SYS_USB_EVENT_POLL_VIA_CONTROL_EP 70 71 #define CONFIG_USBD_HS 72 #define CONFIG_USB_FUNCTION_MASS_STORAGE 73 #define CONFIG_USB_GADGET_VBUS_DRAW 2 74 75 /* Networking Configs */ 76 #define CONFIG_FEC_MXC 77 #define CONFIG_MII 78 #define IMX_FEC_BASE ENET_BASE_ADDR 79 #define CONFIG_FEC_XCV_TYPE RGMII 80 #define CONFIG_ETHPRIME "FEC" 81 #define CONFIG_FEC_MXC_PHYADDR 4 82 #define CONFIG_PHYLIB 83 #define CONFIG_PHY_ATHEROS 84 85 /* Serial Flash */ 86 #ifdef CONFIG_CMD_SF 87 #define CONFIG_MXC_SPI 88 #define CONFIG_SF_DEFAULT_BUS 0 89 #define CONFIG_SF_DEFAULT_CS 0 90 #define CONFIG_SF_DEFAULT_SPEED 20000000 91 #define CONFIG_SF_DEFAULT_MODE SPI_MODE_0 92 #endif 93 94 /* allow to overwrite serial and ethaddr */ 95 #define CONFIG_ENV_OVERWRITE 96 #define CONFIG_CONS_INDEX 1 97 #define CONFIG_BAUDRATE 115200 98 99 /* Command definition */ 100 #define CONFIG_CMD_BMODE 101 102 #define CONFIG_LOADADDR 0x12000000 103 #define CONFIG_SYS_TEXT_BASE 0x17800000 104 105 #define CONFIG_EXTRA_ENV_SETTINGS \ 106 "script=boot.scr\0" \ 107 "image=" CONFIG_BOOT_DIR "/uImage\0" \ 108 "uboot=u-boot.imx\0" \ 109 "fdt_file=" CONFIG_BOOT_DIR "/" CONFIG_DEFAULT_FDT_FILE "\0" \ 110 "fdt_addr=0x18000000\0" \ 111 "boot_fdt=yes\0" \ 112 "ip_dyn=yes\0" \ 113 "console=" CONSOLE_DEV "\0" \ 114 "fdt_high=0xffffffff\0" \ 115 "initrd_high=0xffffffff\0" \ 116 "sddev=0\0" \ 117 "emmcdev=1\0" \ 118 "partnum=1\0" \ 119 "loadcmd=" CONFIG_LOADCMD "\0" \ 120 "rfspart=" CONFIG_RFSPART "\0" \ 121 "update_sd_firmware=" \ 122 "if test ${ip_dyn} = yes; then " \ 123 "setenv get_cmd dhcp; " \ 124 "else " \ 125 "setenv get_cmd tftp; " \ 126 "fi; " \ 127 "if mmc dev ${mmcdev}; then " \ 128 "if ${get_cmd} ${update_sd_firmware_filename}; then " \ 129 "setexpr fw_sz ${filesize} / 0x200; " \ 130 "setexpr fw_sz ${fw_sz} + 1; " \ 131 "mmc write ${loadaddr} 0x2 ${fw_sz}; " \ 132 "fi; " \ 133 "fi\0" \ 134 "update_sf_uboot=" \ 135 "if tftp $loadaddr $uboot; then " \ 136 "sf probe; " \ 137 "sf erase 0 0xC0000; " \ 138 "sf write $loadaddr 0x400 $filesize; " \ 139 "echo 'U-Boot upgraded. Please reset'; " \ 140 "fi\0" \ 141 "setargs=setenv bootargs console=${console},${baudrate} " \ 142 "root=/dev/${rootdev} rw rootwait " CONFIG_EXTRA_BOOTARGS "\0" \ 143 "loadbootscript=" \ 144 "${loadcmd} ${dev} ${devnum}:${partnum} ${loadaddr} ${script};\0" \ 145 "bootscript=echo Running bootscript from ${dev}:${devnum}:${partnum};" \ 146 " source\0" \ 147 "loadimage=" \ 148 "${loadcmd} ${dev} ${devnum}:${partnum} ${loadaddr} ${image}\0" \ 149 "loadfdt=${loadcmd} ${dev} ${devnum}:${partnum} ${fdt_addr} ${fdt_file}\0" \ 150 "tryboot=" \ 151 "if run loadbootscript; then " \ 152 "run bootscript; " \ 153 "else " \ 154 "if run loadimage; then " \ 155 "run doboot; " \ 156 "fi; " \ 157 "fi;\0" \ 158 "doboot=echo Booting from ${dev}:${devnum}:${partnum} ...; " \ 159 "run setargs; " \ 160 "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ 161 "if run loadfdt; then " \ 162 "bootm ${loadaddr} - ${fdt_addr}; " \ 163 "else " \ 164 "if test ${boot_fdt} = try; then " \ 165 "bootm; " \ 166 "else " \ 167 "echo WARN: Cannot load the DT; " \ 168 "fi; " \ 169 "fi; " \ 170 "else " \ 171 "bootm; " \ 172 "fi;\0" \ 173 "netargs=setenv bootargs console=${console},${baudrate} " \ 174 "root=/dev/nfs " \ 175 "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \ 176 "netboot=echo Booting from net ...; " \ 177 "run netargs; " \ 178 "if test ${ip_dyn} = yes; then " \ 179 "setenv get_cmd dhcp; " \ 180 "else " \ 181 "setenv get_cmd tftp; " \ 182 "fi; " \ 183 "${get_cmd} ${image}; " \ 184 "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ 185 "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \ 186 "bootm ${loadaddr} - ${fdt_addr}; " \ 187 "else " \ 188 "if test ${boot_fdt} = try; then " \ 189 "bootm; " \ 190 "else " \ 191 "echo WARN: Cannot load the DT; " \ 192 "fi; " \ 193 "fi; " \ 194 "else " \ 195 "bootm; " \ 196 "fi;\0" \ 197 198 #define CONFIG_BOOTCOMMAND \ 199 "usb start; " \ 200 "setenv dev usb; " \ 201 "setenv devnum 0; " \ 202 "setenv rootdev sda${rfspart}; " \ 203 "run tryboot; " \ 204 \ 205 "setenv dev mmc; " \ 206 "setenv rootdev mmcblk0p${rfspart}; " \ 207 \ 208 "setenv devnum ${sddev}; " \ 209 "if mmc dev ${devnum}; then " \ 210 "run tryboot; " \ 211 "fi; " \ 212 \ 213 "setenv devnum ${emmcdev}; " \ 214 "setenv rootdev mmcblk${emmcdev}p${rfspart}; " \ 215 "if mmc dev ${devnum}; then " \ 216 "run tryboot; " \ 217 "fi; " \ 218 \ 219 "bmode usb; " \ 220 221 #define CONFIG_ARP_TIMEOUT 200UL 222 223 /* Miscellaneous configurable options */ 224 #define CONFIG_SYS_LONGHELP 225 #define CONFIG_AUTO_COMPLETE 226 227 /* Print Buffer Size */ 228 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) 229 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE 230 231 #define CONFIG_SYS_MEMTEST_START 0x10000000 232 #define CONFIG_SYS_MEMTEST_END 0x10010000 233 #define CONFIG_SYS_MEMTEST_SCRATCH 0x10800000 234 235 #define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR 236 237 #define CONFIG_CMDLINE_EDITING 238 #define CONFIG_STACKSIZE (128 * 1024) 239 240 /* Physical Memory Map */ 241 #define CONFIG_NR_DRAM_BANKS 1 242 #define PHYS_SDRAM MMDC0_ARB_BASE_ADDR 243 244 #define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM 245 #define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR 246 #define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE 247 248 #define CONFIG_SYS_INIT_SP_OFFSET \ 249 (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 250 #define CONFIG_SYS_INIT_SP_ADDR \ 251 (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) 252 253 /* FLASH and environment organization */ 254 #define CONFIG_SYS_NO_FLASH 255 256 #define CONFIG_ENV_IS_IN_SPI_FLASH 257 #define CONFIG_ENV_SIZE (8 * 1024) 258 #define CONFIG_ENV_OFFSET (768 * 1024) 259 #define CONFIG_ENV_SECT_SIZE (64 * 1024) 260 #define CONFIG_ENV_SPI_BUS CONFIG_SF_DEFAULT_BUS 261 #define CONFIG_ENV_SPI_CS CONFIG_SF_DEFAULT_CS 262 #define CONFIG_ENV_SPI_MODE CONFIG_SF_DEFAULT_MODE 263 #define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED 264 265 #ifndef CONFIG_SYS_DCACHE_OFF 266 #endif 267 268 #define CONFIG_SYS_FSL_USDHC_NUM 3 269 270 /* Framebuffer */ 271 #define CONFIG_VIDEO_IPUV3 272 #define CONFIG_VIDEO_BMP_RLE8 273 #define CONFIG_SPLASH_SCREEN 274 #define CONFIG_SPLASH_SCREEN_ALIGN 275 #define CONFIG_BMP_16BPP 276 #define CONFIG_VIDEO_LOGO 277 #define CONFIG_VIDEO_BMP_LOGO 278 #define CONFIG_IPUV3_CLK 260000000 279 #define CONFIG_IMX_HDMI 280 #define CONFIG_IMX_VIDEO_SKIP 281 282 #define CONFIG_PWM_IMX 283 #define CONFIG_IMX6_PWM_PER_CLK 66000000 284 285 #undef CONFIG_CMD_PCI 286 #ifdef CONFIG_CMD_PCI 287 #define CONFIG_PCI_SCAN_SHOW 288 #define CONFIG_PCIE_IMX 289 #define CONFIG_PCIE_IMX_PERST_GPIO IMX_GPIO_NR(7, 12) 290 #define CONFIG_PCIE_IMX_POWER_GPIO IMX_GPIO_NR(1, 5) 291 #endif 292 293 /* I2C Configs */ 294 #define CONFIG_SYS_I2C 295 #define CONFIG_SYS_I2C_MXC 296 #define CONFIG_SYS_I2C_SPEED 100000 297 #define CONFIG_SYS_I2C_MXC_I2C1 298 #define CONFIG_SYS_I2C_MXC_I2C2 299 #define CONFIG_SYS_I2C_MXC_I2C3 300 301 #endif /* __ADVANTECH_DMSBA16_CONFIG_H */ 302