1 /* SPDX-License-Identifier: GPL-2.0+ */ 2 /* 3 * Copyright 2013-2015 Arcturus Networks, Inc. 4 * http://www.arcturusnetworks.com/products/ucp1020/ 5 * based on include/configs/p1_p2_rdb_pc.h 6 * original copyright follows: 7 * Copyright 2009-2011 Freescale Semiconductor, Inc. 8 */ 9 10 /* 11 * QorIQ uCP1020-xx boards configuration file 12 */ 13 #ifndef __CONFIG_H 14 #define __CONFIG_H 15 16 #define CONFIG_PCIE1 /* PCIE controller 1 (slot 1) */ 17 #define CONFIG_PCIE2 /* PCIE controller 2 (slot 2) */ 18 #define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ 19 #define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ 20 #define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata */ 21 #define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ 22 23 #if defined(CONFIG_TARTGET_UCP1020T1) 24 25 #define CONFIG_UCP1020_REV_1_3 26 27 #define CONFIG_BOARDNAME "uCP1020-64EE512-0U1-XR-T1" 28 29 #define CONFIG_TSEC1 30 #define CONFIG_TSEC3 31 #define CONFIG_HAS_ETH0 32 #define CONFIG_HAS_ETH1 33 #define CONFIG_ETHADDR 00:19:D3:FF:FF:FF 34 #define CONFIG_ETH1ADDR 00:19:D3:FF:FF:FE 35 #define CONFIG_ETH2ADDR 00:19:D3:FF:FF:FD 36 #define CONFIG_IPADDR 10.80.41.229 37 #define CONFIG_SERVERIP 10.80.41.227 38 #define CONFIG_NETMASK 255.255.252.0 39 #define CONFIG_ETHPRIME "eTSEC3" 40 41 #define CONFIG_SYS_REDUNDAND_ENVIRONMENT 42 43 #define CONFIG_SYS_L2_SIZE (256 << 10) 44 45 #endif 46 47 #if defined(CONFIG_TARGET_UCP1020) 48 49 #define CONFIG_UCP1020 50 #define CONFIG_UCP1020_REV_1_3 51 52 #define CONFIG_BOARDNAME_LOCAL "uCP1020-64EEE512-OU1-XR" 53 54 #define CONFIG_TSEC1 55 #define CONFIG_TSEC2 56 #define CONFIG_TSEC3 57 #define CONFIG_HAS_ETH0 58 #define CONFIG_HAS_ETH1 59 #define CONFIG_HAS_ETH2 60 #define CONFIG_ETHADDR 00:06:3B:FF:FF:FF 61 #define CONFIG_ETH1ADDR 00:06:3B:FF:FF:FE 62 #define CONFIG_ETH2ADDR 00:06:3B:FF:FF:FD 63 #define CONFIG_IPADDR 192.168.1.81 64 #define CONFIG_IPADDR1 192.168.1.82 65 #define CONFIG_IPADDR2 192.168.1.83 66 #define CONFIG_SERVERIP 192.168.1.80 67 #define CONFIG_GATEWAYIP 102.168.1.1 68 #define CONFIG_NETMASK 255.255.255.0 69 #define CONFIG_ETHPRIME "eTSEC1" 70 71 #define CONFIG_SYS_REDUNDAND_ENVIRONMENT 72 73 #define CONFIG_SYS_L2_SIZE (256 << 10) 74 75 #endif 76 77 #ifdef CONFIG_SDCARD 78 #define CONFIG_RAMBOOT_SDCARD 79 #define CONFIG_SYS_RAMBOOT 80 #define CONFIG_SYS_EXTRA_ENV_RELOC 81 #define CONFIG_RESET_VECTOR_ADDRESS 0x1107fffc 82 #endif 83 84 #ifdef CONFIG_SPIFLASH 85 #define CONFIG_RAMBOOT_SPIFLASH 86 #define CONFIG_SYS_RAMBOOT 87 #define CONFIG_SYS_EXTRA_ENV_RELOC 88 #define CONFIG_RESET_VECTOR_ADDRESS 0x1107fffc 89 #endif 90 91 #define CONFIG_SYS_TEXT_BASE_NOR 0xeff80000 92 93 #ifndef CONFIG_RESET_VECTOR_ADDRESS 94 #define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc 95 #endif 96 97 #ifndef CONFIG_SYS_MONITOR_BASE 98 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 99 #endif 100 101 #define CONFIG_ENV_OVERWRITE 102 103 #define CONFIG_SYS_SATA_MAX_DEVICE 2 104 #define CONFIG_LBA48 105 106 #define CONFIG_SYS_CLK_FREQ 66666666 107 #define CONFIG_DDR_CLK_FREQ 66666666 108 109 #define CONFIG_HWCONFIG 110 111 /* 112 * These can be toggled for performance analysis, otherwise use default. 113 */ 114 #define CONFIG_L2_CACHE 115 #define CONFIG_BTB 116 117 #define CONFIG_ENABLE_36BIT_PHYS 118 119 #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ 120 #define CONFIG_SYS_MEMTEST_END 0x1fffffff 121 122 #define CONFIG_SYS_CCSRBAR 0xffe00000 123 #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR 124 125 /* IN case of NAND bootloader relocate CCSRBAR in RAMboot code not in the 4k 126 SPL code*/ 127 #ifdef CONFIG_SPL_BUILD 128 #define CONFIG_SYS_CCSR_DO_NOT_RELOCATE 129 #endif 130 131 /* DDR Setup */ 132 #define CONFIG_DDR_ECC_ENABLE 133 #ifndef CONFIG_DDR_ECC_ENABLE 134 #define CONFIG_SYS_DDR_RAW_TIMING 135 #define CONFIG_DDR_SPD 136 #endif 137 #define CONFIG_SYS_SPD_BUS_NUM 1 138 #undef CONFIG_FSL_DDR_INTERACTIVE 139 140 #define CONFIG_SYS_SDRAM_SIZE_LAW LAW_SIZE_512M 141 #define CONFIG_CHIP_SELECTS_PER_CTRL 1 142 #define CONFIG_SYS_SDRAM_SIZE (1u << (CONFIG_SYS_SDRAM_SIZE_LAW - 19)) 143 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 144 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 145 146 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 147 148 /* Default settings for DDR3 */ 149 #define CONFIG_SYS_DDR_CS0_BNDS 0x0000003f 150 #define CONFIG_SYS_DDR_CS0_CONFIG 0x80014302 151 #define CONFIG_SYS_DDR_CS0_CONFIG_2 0x00000000 152 #define CONFIG_SYS_DDR_CS1_BNDS 0x0040007f 153 #define CONFIG_SYS_DDR_CS1_CONFIG 0x80014302 154 #define CONFIG_SYS_DDR_CS1_CONFIG_2 0x00000000 155 156 #define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef 157 #define CONFIG_SYS_DDR_INIT_ADDR 0x00000000 158 #define CONFIG_SYS_DDR_INIT_EXT_ADDR 0x00000000 159 #define CONFIG_SYS_DDR_MODE_CONTROL 0x00000000 160 161 #define CONFIG_SYS_DDR_ZQ_CONTROL 0x89080600 162 #define CONFIG_SYS_DDR_WRLVL_CONTROL 0x8655A608 163 #define CONFIG_SYS_DDR_SR_CNTR 0x00000000 164 #define CONFIG_SYS_DDR_RCW_1 0x00000000 165 #define CONFIG_SYS_DDR_RCW_2 0x00000000 166 #ifdef CONFIG_DDR_ECC_ENABLE 167 #define CONFIG_SYS_DDR_CONTROL 0xE70C0000 /* Type = DDR3 & ECC */ 168 #else 169 #define CONFIG_SYS_DDR_CONTROL 0xC70C0000 /* Type = DDR3 */ 170 #endif 171 #define CONFIG_SYS_DDR_CONTROL_2 0x04401050 172 #define CONFIG_SYS_DDR_TIMING_4 0x00220001 173 #define CONFIG_SYS_DDR_TIMING_5 0x03402400 174 175 #define CONFIG_SYS_DDR_TIMING_3 0x00020000 176 #define CONFIG_SYS_DDR_TIMING_0 0x00330004 177 #define CONFIG_SYS_DDR_TIMING_1 0x6f6B4846 178 #define CONFIG_SYS_DDR_TIMING_2 0x0FA8C8CF 179 #define CONFIG_SYS_DDR_CLK_CTRL 0x03000000 180 #define CONFIG_SYS_DDR_MODE_1 0x40461520 181 #define CONFIG_SYS_DDR_MODE_2 0x8000c000 182 #define CONFIG_SYS_DDR_INTERVAL 0x0C300000 183 184 #undef CONFIG_CLOCKS_IN_MHZ 185 186 /* 187 * Memory map 188 * 189 * 0x0000_0000 0x7fff_ffff DDR Up to 2GB cacheable 190 * 0x8000_0000 0xdfff_ffff PCI Express Mem 1G non-cacheable(PCIe * 2) 191 * 0xec00_0000 0xefff_ffff NOR flash Up to 64M non-cacheable CS0/1 192 * 0xf8f8_0000 0xf8ff_ffff L2 SRAM Up to 256K cacheable 193 * (early boot only) 194 * 0xffc0_0000 0xffc3_ffff PCI IO range 256k non-cacheable 195 * 0xffd0_0000 0xffd0_3fff L1 for stack 16K cacheable 196 * 0xffe0_0000 0xffef_ffff CCSR 1M non-cacheable 197 */ 198 199 /* 200 * Local Bus Definitions 201 */ 202 #define CONFIG_SYS_MAX_FLASH_SECT 512 /* 64M */ 203 #define CONFIG_SYS_FLASH_BASE 0xec000000 204 205 #define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE 206 207 #define CONFIG_FLASH_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \ 208 | BR_PS_16 | BR_V) 209 210 #define CONFIG_FLASH_OR_PRELIM 0xfc000ff7 211 212 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS} 213 #define CONFIG_SYS_FLASH_QUIET_TEST 214 #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ 215 216 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 217 218 #undef CONFIG_SYS_FLASH_CHECKSUM 219 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 220 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 221 222 #define CONFIG_FLASH_CFI_DRIVER 223 #define CONFIG_SYS_FLASH_CFI 224 #define CONFIG_SYS_FLASH_EMPTY_INFO 225 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 226 227 #define CONFIG_SYS_INIT_RAM_LOCK 228 #define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* stack in RAM */ 229 /* Initial L1 address */ 230 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS CONFIG_SYS_INIT_RAM_ADDR 231 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0 232 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS 233 /* Size of used area in RAM */ 234 #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 235 236 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ 237 GENERATED_GBL_DATA_SIZE) 238 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 239 240 #define CONFIG_SYS_MONITOR_LEN (256 * 1024)/* Reserve 256 kB for Mon */ 241 #define CONFIG_SYS_MALLOC_LEN (1024 * 1024)/* Reserved for malloc */ 242 243 #define CONFIG_SYS_PMC_BASE 0xff980000 244 #define CONFIG_SYS_PMC_BASE_PHYS CONFIG_SYS_PMC_BASE 245 #define CONFIG_PMC_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_PMC_BASE_PHYS) | \ 246 BR_PS_8 | BR_V) 247 #define CONFIG_PMC_OR_PRELIM (OR_AM_64KB | OR_GPCM_CSNT | OR_GPCM_XACS | \ 248 OR_GPCM_SCY | OR_GPCM_TRLX | OR_GPCM_EHTR | \ 249 OR_GPCM_EAD) 250 251 #define CONFIG_SYS_BR0_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */ 252 #define CONFIG_SYS_OR0_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */ 253 #ifdef CONFIG_NAND_FSL_ELBC 254 #define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Addr */ 255 #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ 256 #endif 257 258 /* Serial Port - controlled on board with jumper J8 259 * open - index 2 260 * shorted - index 1 261 */ 262 #undef CONFIG_SERIAL_SOFTWARE_FIFO 263 #define CONFIG_SYS_NS16550_SERIAL 264 #define CONFIG_SYS_NS16550_REG_SIZE 1 265 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 266 #if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_INIT_MINIMAL) 267 #define CONFIG_NS16550_MIN_FUNCTIONS 268 #endif 269 270 #define CONFIG_SYS_BAUDRATE_TABLE \ 271 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} 272 273 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR + 0x4500) 274 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR + 0x4600) 275 276 /* I2C */ 277 #define CONFIG_SYS_I2C 278 #define CONFIG_SYS_I2C_FSL 279 #define CONFIG_SYS_FSL_I2C_SPEED 400000 280 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 281 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 282 #define CONFIG_SYS_FSL_I2C2_SPEED 400000 283 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F 284 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 285 #define CONFIG_SYS_I2C_NOPROBES { {0, 0x29} } 286 #define CONFIG_SYS_SPD_BUS_NUM 1 /* For rom_loc and flash bank */ 287 288 #define CONFIG_RTC_DS1337 289 #define CONFIG_RTC_DS1337_NOOSC 290 #define CONFIG_SYS_I2C_RTC_ADDR 0x68 291 #define CONFIG_SYS_I2C_PCA9557_ADDR 0x18 292 #define CONFIG_SYS_I2C_NCT72_ADDR 0x4C 293 #define CONFIG_SYS_I2C_IDT6V49205B 0x69 294 295 /* 296 * eSPI - Enhanced SPI 297 */ 298 #define CONFIG_HARD_SPI 299 300 #define CONFIG_SF_DEFAULT_SPEED 10000000 301 #define CONFIG_SF_DEFAULT_MODE SPI_MODE_0 302 303 #if defined(CONFIG_PCI) 304 /* 305 * General PCI 306 * Memory space is mapped 1-1, but I/O space must start from 0. 307 */ 308 309 /* controller 2, direct to uli, tgtid 2, Base address 9000 */ 310 #define CONFIG_SYS_PCIE2_NAME "PCIe SLOT CON9" 311 #define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 312 #define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000 313 #define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000 314 #define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */ 315 #define CONFIG_SYS_PCIE2_IO_VIRT 0xffc10000 316 #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 317 #define CONFIG_SYS_PCIE2_IO_PHYS 0xffc10000 318 #define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ 319 320 /* controller 1, Slot 2, tgtid 1, Base address a000 */ 321 #define CONFIG_SYS_PCIE1_NAME "PCIe SLOT CON10" 322 #define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 323 #define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000 324 #define CONFIG_SYS_PCIE1_MEM_PHYS 0x80000000 325 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ 326 #define CONFIG_SYS_PCIE1_IO_VIRT 0xffc00000 327 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 328 #define CONFIG_SYS_PCIE1_IO_PHYS 0xffc00000 329 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ 330 331 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 332 #endif /* CONFIG_PCI */ 333 334 /* 335 * Environment 336 */ 337 #ifdef CONFIG_ENV_FIT_UCBOOT 338 339 #define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x20000) 340 #define CONFIG_ENV_SIZE 0x20000 341 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ 342 343 #else 344 345 #define CONFIG_ENV_SPI_BUS 0 346 #define CONFIG_ENV_SPI_CS 0 347 #define CONFIG_ENV_SPI_MAX_HZ 10000000 348 #define CONFIG_ENV_SPI_MODE 0 349 350 #ifdef CONFIG_RAMBOOT_SPIFLASH 351 352 #define CONFIG_ENV_SIZE 0x3000 /* 12KB */ 353 #define CONFIG_ENV_OFFSET 0x2000 /* 8KB */ 354 #define CONFIG_ENV_SECT_SIZE 0x1000 355 356 #if defined(CONFIG_SYS_REDUNDAND_ENVIRONMENT) 357 /* Address and size of Redundant Environment Sector */ 358 #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) 359 #define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE 360 #endif 361 362 #elif defined(CONFIG_RAMBOOT_SDCARD) 363 #define CONFIG_FSL_FIXED_MMC_LOCATION 364 #define CONFIG_ENV_SIZE 0x2000 365 #define CONFIG_SYS_MMC_ENV_DEV 0 366 367 #elif defined(CONFIG_SYS_RAMBOOT) 368 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) 369 #define CONFIG_ENV_SIZE 0x2000 370 371 #else 372 #define CONFIG_ENV_BASE (CONFIG_SYS_FLASH_BASE) 373 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ 374 #define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE 375 #define CONFIG_ENV_ADDR (CONFIG_ENV_BASE + 0xC0000) 376 #if defined(CONFIG_SYS_REDUNDAND_ENVIRONMENT) 377 /* Address and size of Redundant Environment Sector */ 378 #define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SIZE) 379 #define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE 380 #endif 381 382 #endif 383 384 #endif /* CONFIG_ENV_FIT_UCBOOT */ 385 386 #define CONFIG_LOADS_ECHO /* echo on for serial download */ 387 #define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ 388 389 /* 390 * USB 391 */ 392 #define CONFIG_HAS_FSL_DR_USB 393 394 #if defined(CONFIG_HAS_FSL_DR_USB) 395 #define CONFIG_USB_MAX_CONTROLLER_COUNT 1 396 397 #ifdef CONFIG_USB_EHCI_HCD 398 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET 399 #define CONFIG_USB_EHCI_FSL 400 #endif 401 #endif 402 403 #undef CONFIG_WATCHDOG /* watchdog disabled */ 404 405 #ifdef CONFIG_MMC 406 #define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR 407 #define CONFIG_MMC_SPI 408 #endif 409 410 /* Misc Extra Settings */ 411 #undef CONFIG_WATCHDOG /* watchdog disabled */ 412 413 /* 414 * Miscellaneous configurable options 415 */ 416 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 417 #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms tick */ 418 419 /* 420 * For booting Linux, the board info and command line data 421 * have to be in the first 64 MB of memory, since this is 422 * the maximum mapped by the Linux kernel during initialization. 423 */ 424 #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory for Linux*/ 425 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 426 427 #if defined(CONFIG_CMD_KGDB) 428 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ 429 #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ 430 #endif 431 432 /* 433 * Environment Configuration 434 */ 435 436 #if defined(CONFIG_TSEC_ENET) 437 438 #if defined(CONFIG_UCP1020_REV_1_2) || defined(CONFIG_UCP1020_REV_1_3) 439 #else 440 #error "UCP1020 module revision is not defined !!!" 441 #endif 442 443 #define CONFIG_BOOTP_SERVERIP 444 445 #define CONFIG_TSEC1_NAME "eTSEC1" 446 #define CONFIG_TSEC2_NAME "eTSEC2" 447 #define CONFIG_TSEC3_NAME "eTSEC3" 448 449 #define TSEC1_PHY_ADDR 4 450 #define TSEC2_PHY_ADDR 0 451 #define TSEC2_PHY_ADDR_SGMII 0x00 452 #define TSEC3_PHY_ADDR 6 453 454 #define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 455 #define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 456 #define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 457 458 #define TSEC1_PHYIDX 0 459 #define TSEC2_PHYIDX 0 460 #define TSEC3_PHYIDX 0 461 462 #endif 463 464 #define CONFIG_HOSTNAME "UCP1020" 465 #define CONFIG_ROOTPATH "/opt/nfsroot" 466 #define CONFIG_BOOTFILE "uImage" 467 #define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */ 468 469 /* default location for tftp and bootm */ 470 #define CONFIG_LOADADDR 1000000 471 472 #if defined(CONFIG_DONGLE) 473 474 #define CONFIG_EXTRA_ENV_SETTINGS \ 475 "bootcmd=run prog_spi_mbrbootcramfs\0" \ 476 "bootfile=uImage\0" \ 477 "consoledev=ttyS0\0" \ 478 "cramfsfile=image.cramfs\0" \ 479 "dtbaddr=0x00c00000\0" \ 480 "dtbfile=image.dtb\0" \ 481 "ethaddr=" __stringify(CONFIG_ETHADDR) "\0" \ 482 "eth1addr=" __stringify(CONFIG_ETH1ADDR) "\0" \ 483 "eth2addr=" __stringify(CONFIG_ETH2ADDR) "\0" \ 484 "fileaddr=0x01000000\0" \ 485 "filesize=0x00080000\0" \ 486 "flashmbr=sf probe 0; " \ 487 "tftp $loadaddr $mbr; " \ 488 "sf erase $mbr_offset +$filesize; " \ 489 "sf write $loadaddr $mbr_offset $filesize\0" \ 490 "flashrecovery=tftp $recoveryaddr $cramfsfile; " \ 491 "protect off $nor_recoveryaddr +$filesize; " \ 492 "erase $nor_recoveryaddr +$filesize; " \ 493 "cp.b $recoveryaddr $nor_recoveryaddr $filesize; " \ 494 "protect on $nor_recoveryaddr +$filesize\0 " \ 495 "flashuboot=tftp $ubootaddr $ubootfile; " \ 496 "protect off $nor_ubootaddr +$filesize; " \ 497 "erase $nor_ubootaddr +$filesize; " \ 498 "cp.b $ubootaddr $nor_ubootaddr $filesize; " \ 499 "protect on $nor_ubootaddr +$filesize\0 " \ 500 "flashworking=tftp $workingaddr $cramfsfile; " \ 501 "protect off $nor_workingaddr +$filesize; " \ 502 "erase $nor_workingaddr +$filesize; " \ 503 "cp.b $workingaddr $nor_workingaddr $filesize; " \ 504 "protect on $nor_workingaddr +$filesize\0 " \ 505 "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0 " \ 506 "kerneladdr=0x01100000\0" \ 507 "kernelfile=uImage\0" \ 508 "loadaddr=0x01000000\0" \ 509 "mbr=uCP1020d.mbr\0" \ 510 "mbr_offset=0x00000000\0" \ 511 "mmbr=uCP1020Quiet.mbr\0" \ 512 "mmcpart=0:2\0" \ 513 "mmc__mbrd=fatload mmc $mmcpart $loadaddr $mbr; " \ 514 "mmc erase 1 1; " \ 515 "mmc write $loadaddr 1 1\0" \ 516 "mmc__uboot=fatload mmc $mmcpart $loadaddr $ubootfile; " \ 517 "mmc erase 0x40 0x400; " \ 518 "mmc write $loadaddr 0x40 0x400\0" \ 519 "netdev=eth0\0" \ 520 "nor_recoveryaddr=0xEC0A0000\0" \ 521 "nor_ubootaddr=0xEFF80000\0" \ 522 "nor_workingaddr=0xECFA0000\0" \ 523 "norbootrecovery=setenv bootargs $recoverybootargs" \ 524 " console=$consoledev,$baudrate $othbootargs; " \ 525 "run norloadrecovery; " \ 526 "bootm $kerneladdr - $dtbaddr\0" \ 527 "norbootworking=setenv bootargs $workingbootargs" \ 528 " console=$consoledev,$baudrate $othbootargs; " \ 529 "run norloadworking; " \ 530 "bootm $kerneladdr - $dtbaddr\0" \ 531 "norloadrecovery=mw.l $kerneladdr 0x0 0x00a00000; " \ 532 "setenv cramfsaddr $nor_recoveryaddr; " \ 533 "cramfsload $dtbaddr $dtbfile; " \ 534 "cramfsload $kerneladdr $kernelfile\0" \ 535 "norloadworking=mw.l $kerneladdr 0x0 0x00a00000; " \ 536 "setenv cramfsaddr $nor_workingaddr; " \ 537 "cramfsload $dtbaddr $dtbfile; " \ 538 "cramfsload $kerneladdr $kernelfile\0" \ 539 "prog_spi_mbr=run spi__mbr\0" \ 540 "prog_spi_mbrboot=run spi__mbr; run spi__boot1; run spi__boot2\0" \ 541 "prog_spi_mbrbootcramfs=run spi__mbr; run spi__boot1; run spi__boot2; " \ 542 "run spi__cramfs\0" \ 543 "ramboot=setenv bootargs root=/dev/ram ramdisk_size=$ramdisk_size ro" \ 544 " console=$consoledev,$baudrate $othbootargs; " \ 545 "tftp $rootfsaddr $rootfsfile; " \ 546 "tftp $loadaddr $kernelfile; " \ 547 "tftp $dtbaddr $dtbfile; " \ 548 "bootm $loadaddr $rootfsaddr $dtbaddr\0" \ 549 "ramdisk_size=120000\0" \ 550 "ramdiskfile=rootfs.ext2.gz.uboot\0" \ 551 "recoveryaddr=0x02F00000\0" \ 552 "recoverybootargs=root=/dev/mtdblock0 rootfstype=cramfs ro\0" \ 553 "releasefpga=mw.l 0xffe0f000 0x00400000; mw.l 0xffe0f004 0x00000000; " \ 554 "mw.l 0xffe0f008 0x00400000\0" \ 555 "rootfsaddr=0x02F00000\0" \ 556 "rootfsfile=rootfs.ext2.gz.uboot\0" \ 557 "rootpath=/opt/nfsroot\0" \ 558 "spi__boot1=fatload mmc $mmcpart $loadaddr u-boot.bin; " \ 559 "protect off 0xeC000000 +$filesize; " \ 560 "erase 0xEC000000 +$filesize; " \ 561 "cp.b $loadaddr 0xEC000000 $filesize; " \ 562 "cmp.b $loadaddr 0xEC000000 $filesize; " \ 563 "protect on 0xeC000000 +$filesize\0" \ 564 "spi__boot2=fatload mmc $mmcpart $loadaddr u-boot.bin; " \ 565 "protect off 0xeFF80000 +$filesize; " \ 566 "erase 0xEFF80000 +$filesize; " \ 567 "cp.b $loadaddr 0xEFF80000 $filesize; " \ 568 "cmp.b $loadaddr 0xEFF80000 $filesize; " \ 569 "protect on 0xeFF80000 +$filesize\0" \ 570 "spi__bootd=fatload mmc $mmcpart $loadaddr $ubootd; " \ 571 "sf probe 0; sf erase 0x8000 +$filesize; " \ 572 "sf write $loadaddr 0x8000 $filesize\0" \ 573 "spi__cramfs=fatload mmc $mmcpart $loadaddr image.cramfs; " \ 574 "protect off 0xec0a0000 +$filesize; " \ 575 "erase 0xeC0A0000 +$filesize; " \ 576 "cp.b $loadaddr 0xeC0A0000 $filesize; " \ 577 "protect on 0xec0a0000 +$filesize\0" \ 578 "spi__mbr=fatload mmc $mmcpart $loadaddr $mmbr; " \ 579 "sf probe 1; sf erase 0 +$filesize; " \ 580 "sf write $loadaddr 0 $filesize\0" \ 581 "spi__mbrd=fatload mmc $mmcpart $loadaddr $mbr; " \ 582 "sf probe 0; sf erase 0 +$filesize; " \ 583 "sf write $loadaddr 0 $filesize\0" \ 584 "tftpflash=tftpboot $loadaddr $uboot; " \ 585 "protect off " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ 586 "erase " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ 587 "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize; " \ 588 "protect on " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ 589 "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize\0"\ 590 "uboot= " __stringify(CONFIG_UBOOTPATH) "\0" \ 591 "ubootaddr=0x01000000\0" \ 592 "ubootfile=u-boot.bin\0" \ 593 "ubootd=u-boot4dongle.bin\0" \ 594 "upgrade=run flashworking\0" \ 595 "usb_phy_type=ulpi\0 " \ 596 "workingaddr=0x02F00000\0" \ 597 "workingbootargs=root=/dev/mtdblock1 rootfstype=cramfs ro\0" 598 599 #else 600 601 #if defined(CONFIG_UCP1020T1) 602 603 #define CONFIG_EXTRA_ENV_SETTINGS \ 604 "bootcmd=run releasefpga; run norbootworking || run norbootrecovery\0" \ 605 "bootfile=uImage\0" \ 606 "consoledev=ttyS0\0" \ 607 "cramfsfile=image.cramfs\0" \ 608 "dtbaddr=0x00c00000\0" \ 609 "dtbfile=image.dtb\0" \ 610 "ethaddr=" __stringify(CONFIG_ETHADDR) "\0" \ 611 "eth1addr=" __stringify(CONFIG_ETH1ADDR) "\0" \ 612 "eth2addr=" __stringify(CONFIG_ETH2ADDR) "\0" \ 613 "fileaddr=0x01000000\0" \ 614 "filesize=0x00080000\0" \ 615 "flashmbr=sf probe 0; " \ 616 "tftp $loadaddr $mbr; " \ 617 "sf erase $mbr_offset +$filesize; " \ 618 "sf write $loadaddr $mbr_offset $filesize\0" \ 619 "flashrecovery=tftp $recoveryaddr $cramfsfile; " \ 620 "protect off $nor_recoveryaddr +$filesize; " \ 621 "erase $nor_recoveryaddr +$filesize; " \ 622 "cp.b $recoveryaddr $nor_recoveryaddr $filesize; " \ 623 "protect on $nor_recoveryaddr +$filesize\0 " \ 624 "flashuboot=tftp $ubootaddr $ubootfile; " \ 625 "protect off $nor_ubootaddr +$filesize; " \ 626 "erase $nor_ubootaddr +$filesize; " \ 627 "cp.b $ubootaddr $nor_ubootaddr $filesize; " \ 628 "protect on $nor_ubootaddr +$filesize\0 " \ 629 "flashworking=tftp $workingaddr $cramfsfile; " \ 630 "protect off $nor_workingaddr +$filesize; " \ 631 "erase $nor_workingaddr +$filesize; " \ 632 "cp.b $workingaddr $nor_workingaddr $filesize; " \ 633 "protect on $nor_workingaddr +$filesize\0 " \ 634 "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0 " \ 635 "kerneladdr=0x01100000\0" \ 636 "kernelfile=uImage\0" \ 637 "loadaddr=0x01000000\0" \ 638 "mbr=uCP1020.mbr\0" \ 639 "mbr_offset=0x00000000\0" \ 640 "netdev=eth0\0" \ 641 "nor_recoveryaddr=0xEC0A0000\0" \ 642 "nor_ubootaddr=0xEFF80000\0" \ 643 "nor_workingaddr=0xECFA0000\0" \ 644 "norbootrecovery=setenv bootargs $recoverybootargs" \ 645 " console=$consoledev,$baudrate $othbootargs; " \ 646 "run norloadrecovery; " \ 647 "bootm $kerneladdr - $dtbaddr\0" \ 648 "norbootworking=setenv bootargs $workingbootargs" \ 649 " console=$consoledev,$baudrate $othbootargs; " \ 650 "run norloadworking; " \ 651 "bootm $kerneladdr - $dtbaddr\0" \ 652 "norloadrecovery=mw.l $kerneladdr 0x0 0x00a00000; " \ 653 "setenv cramfsaddr $nor_recoveryaddr; " \ 654 "cramfsload $dtbaddr $dtbfile; " \ 655 "cramfsload $kerneladdr $kernelfile\0" \ 656 "norloadworking=mw.l $kerneladdr 0x0 0x00a00000; " \ 657 "setenv cramfsaddr $nor_workingaddr; " \ 658 "cramfsload $dtbaddr $dtbfile; " \ 659 "cramfsload $kerneladdr $kernelfile\0" \ 660 "othbootargs=quiet\0" \ 661 "ramboot=setenv bootargs root=/dev/ram ramdisk_size=$ramdisk_size ro" \ 662 " console=$consoledev,$baudrate $othbootargs; " \ 663 "tftp $rootfsaddr $rootfsfile; " \ 664 "tftp $loadaddr $kernelfile; " \ 665 "tftp $dtbaddr $dtbfile; " \ 666 "bootm $loadaddr $rootfsaddr $dtbaddr\0" \ 667 "ramdisk_size=120000\0" \ 668 "ramdiskfile=rootfs.ext2.gz.uboot\0" \ 669 "recoveryaddr=0x02F00000\0" \ 670 "recoverybootargs=root=/dev/mtdblock0 rootfstype=cramfs ro\0" \ 671 "releasefpga=mw.l 0xffe0f000 0x00400000; mw.l 0xffe0f004 0x00000000; " \ 672 "mw.l 0xffe0f008 0x00400000\0" \ 673 "rootfsaddr=0x02F00000\0" \ 674 "rootfsfile=rootfs.ext2.gz.uboot\0" \ 675 "rootpath=/opt/nfsroot\0" \ 676 "silent=1\0" \ 677 "tftpflash=tftpboot $loadaddr $uboot; " \ 678 "protect off " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ 679 "erase " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ 680 "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize; " \ 681 "protect on " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ 682 "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize\0"\ 683 "uboot= " __stringify(CONFIG_UBOOTPATH) "\0" \ 684 "ubootaddr=0x01000000\0" \ 685 "ubootfile=u-boot.bin\0" \ 686 "upgrade=run flashworking\0" \ 687 "workingaddr=0x02F00000\0" \ 688 "workingbootargs=root=/dev/mtdblock1 rootfstype=cramfs ro\0" 689 690 #else /* For Arcturus Modules */ 691 692 #define CONFIG_EXTRA_ENV_SETTINGS \ 693 "bootcmd=run norkernel\0" \ 694 "bootfile=uImage\0" \ 695 "consoledev=ttyS0\0" \ 696 "dtbaddr=0x00c00000\0" \ 697 "dtbfile=image.dtb\0" \ 698 "ethaddr=" __stringify(CONFIG_ETHADDR) "\0" \ 699 "eth1addr=" __stringify(CONFIG_ETH1ADDR) "\0" \ 700 "eth2addr=" __stringify(CONFIG_ETH2ADDR) "\0" \ 701 "fileaddr=0x01000000\0" \ 702 "filesize=0x00080000\0" \ 703 "flashmbr=sf probe 0; " \ 704 "tftp $loadaddr $mbr; " \ 705 "sf erase $mbr_offset +$filesize; " \ 706 "sf write $loadaddr $mbr_offset $filesize\0" \ 707 "flashuboot=tftp $loadaddr $ubootfile; " \ 708 "protect off $nor_ubootaddr0 +$filesize; " \ 709 "erase $nor_ubootaddr0 +$filesize; " \ 710 "cp.b $loadaddr $nor_ubootaddr0 $filesize; " \ 711 "protect on $nor_ubootaddr0 +$filesize; " \ 712 "protect off $nor_ubootaddr1 +$filesize; " \ 713 "erase $nor_ubootaddr1 +$filesize; " \ 714 "cp.b $loadaddr $nor_ubootaddr1 $filesize; " \ 715 "protect on $nor_ubootaddr1 +$filesize\0 " \ 716 "format0=protect off $part0base +$part0size; " \ 717 "erase $part0base +$part0size\0" \ 718 "format1=protect off $part1base +$part1size; " \ 719 "erase $part1base +$part1size\0" \ 720 "format2=protect off $part2base +$part2size; " \ 721 "erase $part2base +$part2size\0" \ 722 "format3=protect off $part3base +$part3size; " \ 723 "erase $part3base +$part3size\0" \ 724 "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0 " \ 725 "kerneladdr=0x01100000\0" \ 726 "kernelargs=root=/dev/mtdblock1 rootfstype=cramfs ro\0" \ 727 "kernelfile=uImage\0" \ 728 "loadaddr=0x01000000\0" \ 729 "mbr=uCP1020.mbr\0" \ 730 "mbr_offset=0x00000000\0" \ 731 "netdev=eth0\0" \ 732 "nor_ubootaddr0=0xEC000000\0" \ 733 "nor_ubootaddr1=0xEFF80000\0" \ 734 "norkernel=setenv bootargs $kernelargs console=$consoledev,$baudrate; " \ 735 "run norkernelload; " \ 736 "bootm $kerneladdr - $dtbaddr\0" \ 737 "norkernelload=mw.l $kerneladdr 0x0 0x00a00000; " \ 738 "setenv cramfsaddr $part0base; " \ 739 "cramfsload $dtbaddr $dtbfile; " \ 740 "cramfsload $kerneladdr $kernelfile\0" \ 741 "part0base=0xEC100000\0" \ 742 "part0size=0x00700000\0" \ 743 "part1base=0xEC800000\0" \ 744 "part1size=0x02000000\0" \ 745 "part2base=0xEE800000\0" \ 746 "part2size=0x00800000\0" \ 747 "part3base=0xEF000000\0" \ 748 "part3size=0x00F80000\0" \ 749 "partENVbase=0xEC080000\0" \ 750 "partENVsize=0x00080000\0" \ 751 "program0=tftp part0-000000.bin; " \ 752 "protect off $part0base +$filesize; " \ 753 "erase $part0base +$filesize; " \ 754 "cp.b $loadaddr $part0base $filesize; " \ 755 "echo Verifying...; " \ 756 "cmp.b $loadaddr $part0base $filesize\0" \ 757 "program1=tftp part1-000000.bin; " \ 758 "protect off $part1base +$filesize; " \ 759 "erase $part1base +$filesize; " \ 760 "cp.b $loadaddr $part1base $filesize; " \ 761 "echo Verifying...; " \ 762 "cmp.b $loadaddr $part1base $filesize\0" \ 763 "program2=tftp part2-000000.bin; " \ 764 "protect off $part2base +$filesize; " \ 765 "erase $part2base +$filesize; " \ 766 "cp.b $loadaddr $part2base $filesize; " \ 767 "echo Verifying...; " \ 768 "cmp.b $loadaddr $part2base $filesize\0" \ 769 "ramboot=setenv bootargs root=/dev/ram ramdisk_size=$ramdisk_size ro" \ 770 " console=$consoledev,$baudrate $othbootargs; " \ 771 "tftp $rootfsaddr $rootfsfile; " \ 772 "tftp $loadaddr $kernelfile; " \ 773 "tftp $dtbaddr $dtbfile; " \ 774 "bootm $loadaddr $rootfsaddr $dtbaddr\0" \ 775 "ramdisk_size=120000\0" \ 776 "ramdiskfile=rootfs.ext2.gz.uboot\0" \ 777 "releasefpga=mw.l 0xffe0f000 0x00400000; mw.l 0xffe0f004 0x00000000; " \ 778 "mw.l 0xffe0f008 0x00400000\0" \ 779 "rootfsaddr=0x02F00000\0" \ 780 "rootfsfile=rootfs.ext2.gz.uboot\0" \ 781 "rootpath=/opt/nfsroot\0" \ 782 "spi__mbr=fatload mmc $mmcpart $loadaddr $mmbr; " \ 783 "sf probe 0; sf erase 0 +$filesize; " \ 784 "sf write $loadaddr 0 $filesize\0" \ 785 "spi__boot=fatload mmc $mmcpart $loadaddr u-boot.bin; " \ 786 "protect off 0xeC000000 +$filesize; " \ 787 "erase 0xEC000000 +$filesize; " \ 788 "cp.b $loadaddr 0xEC000000 $filesize; " \ 789 "cmp.b $loadaddr 0xEC000000 $filesize; " \ 790 "protect on 0xeC000000 +$filesize\0" \ 791 "tftpflash=tftpboot $loadaddr $uboot; " \ 792 "protect off " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ 793 "erase " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ 794 "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize; " \ 795 "protect on " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ 796 "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize\0"\ 797 "uboot= " __stringify(CONFIG_UBOOTPATH) "\0" \ 798 "ubootfile=u-boot.bin\0" \ 799 "upgrade=run flashuboot\0" \ 800 "usb_phy_type=ulpi\0 " \ 801 "boot_nfs= " \ 802 "setenv bootargs root=/dev/nfs rw " \ 803 "nfsroot=$serverip:$rootpath " \ 804 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 805 "console=$consoledev,$baudrate $othbootargs;" \ 806 "tftp $loadaddr $bootfile;" \ 807 "tftp $fdtaddr $fdtfile;" \ 808 "bootm $loadaddr - $fdtaddr\0" \ 809 "boot_hd = " \ 810 "setenv bootargs root=/dev/$bdev rw rootdelay=30 " \ 811 "console=$consoledev,$baudrate $othbootargs;" \ 812 "usb start;" \ 813 "ext2load usb 0:1 $loadaddr /boot/$bootfile;" \ 814 "ext2load usb 0:1 $fdtaddr /boot/$fdtfile;" \ 815 "bootm $loadaddr - $fdtaddr\0" \ 816 "boot_usb_fat = " \ 817 "setenv bootargs root=/dev/ram rw " \ 818 "console=$consoledev,$baudrate $othbootargs " \ 819 "ramdisk_size=$ramdisk_size;" \ 820 "usb start;" \ 821 "fatload usb 0:2 $loadaddr $bootfile;" \ 822 "fatload usb 0:2 $fdtaddr $fdtfile;" \ 823 "fatload usb 0:2 $ramdiskaddr $ramdiskfile;" \ 824 "bootm $loadaddr $ramdiskaddr $fdtaddr\0 " \ 825 "boot_usb_ext2 = " \ 826 "setenv bootargs root=/dev/ram rw " \ 827 "console=$consoledev,$baudrate $othbootargs " \ 828 "ramdisk_size=$ramdisk_size;" \ 829 "usb start;" \ 830 "ext2load usb 0:4 $loadaddr $bootfile;" \ 831 "ext2load usb 0:4 $fdtaddr $fdtfile;" \ 832 "ext2load usb 0:4 $ramdiskaddr $ramdiskfile;" \ 833 "bootm $loadaddr $ramdiskaddr $fdtaddr\0 " \ 834 "boot_nor = " \ 835 "setenv bootargs root=/dev/$jffs2nor rw " \ 836 "console=$consoledev,$baudrate rootfstype=jffs2 $othbootargs;" \ 837 "bootm $norbootaddr - $norfdtaddr\0 " \ 838 "boot_ram = " \ 839 "setenv bootargs root=/dev/ram rw " \ 840 "console=$consoledev,$baudrate $othbootargs " \ 841 "ramdisk_size=$ramdisk_size;" \ 842 "tftp $ramdiskaddr $ramdiskfile;" \ 843 "tftp $loadaddr $bootfile;" \ 844 "tftp $fdtaddr $fdtfile;" \ 845 "bootm $loadaddr $ramdiskaddr $fdtaddr\0" 846 847 #endif 848 #endif 849 850 #endif /* __CONFIG_H */ 851