1 /* 2 * (C) Copyright 2005 3 * Wolfgang Denk, DENX Software Engineering, wd@denx.de. 4 * 5 * SPDX-License-Identifier: GPL-2.0+ 6 */ 7 8 /* 9 * TQM8349 board configuration file 10 */ 11 12 #ifndef __CONFIG_H 13 #define __CONFIG_H 14 15 /* 16 * High Level Configuration Options 17 */ 18 #define CONFIG_E300 1 /* E300 Family */ 19 #define CONFIG_MPC834x 1 /* MPC834x specific */ 20 #define CONFIG_MPC8349 1 /* MPC8349 specific */ 21 #define CONFIG_TQM834X 1 /* TQM834X board specific */ 22 23 #define CONFIG_SYS_TEXT_BASE 0x80000000 24 25 /* IMMR Base Address Register, use Freescale default: 0xff400000 */ 26 #define CONFIG_SYS_IMMR 0xff400000 27 28 /* System clock. Primary input clock when in PCI host mode */ 29 #define CONFIG_83XX_CLKIN 66666000 /* 66,666 MHz */ 30 31 /* 32 * Local Bus LCRR 33 * LCRR: DLL bypass, Clock divider is 8 34 * 35 * for CSB = 266 MHz it gives LCB clock frequency = 33 MHz 36 * 37 * External Local Bus rate is 38 * CLKIN * HRCWL_CSB_TO_CLKIN / HRCWL_LCL_BUS_TO_SCB_CLK / LCRR_CLKDIV 39 */ 40 #define CONFIG_SYS_LCRR_DBYP LCRR_DBYP 41 #define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_8 42 43 /* board pre init: do not call, nothing to do */ 44 45 /* detect the number of flash banks */ 46 #define CONFIG_BOARD_EARLY_INIT_R 47 48 /* 49 * DDR Setup 50 */ 51 /* DDR is system memory*/ 52 #define CONFIG_SYS_DDR_BASE 0x00000000 53 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE 54 #define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE 55 #define DDR_CASLAT_25 /* CASLAT set to 2.5 */ 56 #undef CONFIG_DDR_ECC /* only for ECC DDR module */ 57 #undef CONFIG_SPD_EEPROM /* do not use SPD EEPROM for DDR setup */ 58 59 #undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */ 60 #define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest region */ 61 #define CONFIG_SYS_MEMTEST_END 0x00100000 62 63 /* 64 * FLASH on the Local Bus 65 */ 66 #define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */ 67 #define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */ 68 #undef CONFIG_SYS_FLASH_CHECKSUM 69 #define CONFIG_SYS_FLASH_BASE 0x80000000 /* start of FLASH */ 70 #define CONFIG_SYS_FLASH_SIZE 8 /* FLASH size in MB */ 71 #define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sectors */ 72 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 73 74 /* 75 * FLASH bank number detection 76 */ 77 78 /* 79 * When CONFIG_SYS_MAX_FLASH_BANKS_DETECT is defined, the actual number of 80 * Flash banks has to be determined at runtime and stored in a gloabl variable 81 * tqm834x_num_flash_banks. The value of CONFIG_SYS_MAX_FLASH_BANKS_DETECT is 82 * only used instead of CONFIG_SYS_MAX_FLASH_BANKS to allocate the array 83 * flash_info, and should be made sufficiently large to accomodate the number 84 * of banks that might actually be detected. Since most (all?) Flash related 85 * functions use CONFIG_SYS_MAX_FLASH_BANKS as the number of actual banks on 86 * the board, it is defined as tqm834x_num_flash_banks. 87 */ 88 #define CONFIG_SYS_MAX_FLASH_BANKS_DETECT 2 89 90 #define CONFIG_SYS_MAX_FLASH_SECT 512 /* max sectors per device */ 91 92 /* 32 bit device at 0x80000000 via GPCM (0x8000_1801) */ 93 #define CONFIG_SYS_BR0_PRELIM ((CONFIG_SYS_FLASH_BASE & BR_BA) \ 94 | BR_MS_GPCM \ 95 | BR_PS_32 \ 96 | BR_V) 97 98 /* FLASH timing (0x0000_0c54) */ 99 #define CONFIG_SYS_OR_TIMING_FLASH (OR_GPCM_CSNT \ 100 | OR_GPCM_ACS_DIV4 \ 101 | OR_GPCM_SCY_5 \ 102 | OR_GPCM_TRLX) 103 104 #define CONFIG_SYS_PRELIM_OR_AM OR_AM_1GB /* OR addr mask: 1 GiB */ 105 106 #define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM \ 107 | CONFIG_SYS_OR_TIMING_FLASH) 108 109 #define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_1GB) 110 111 /* Window base at flash base */ 112 #define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE 113 114 /* disable remaining mappings */ 115 #define CONFIG_SYS_BR1_PRELIM 0x00000000 116 #define CONFIG_SYS_OR1_PRELIM 0x00000000 117 #define CONFIG_SYS_LBLAWBAR1_PRELIM 0x00000000 118 #define CONFIG_SYS_LBLAWAR1_PRELIM 0x00000000 119 120 #define CONFIG_SYS_BR2_PRELIM 0x00000000 121 #define CONFIG_SYS_OR2_PRELIM 0x00000000 122 #define CONFIG_SYS_LBLAWBAR2_PRELIM 0x00000000 123 #define CONFIG_SYS_LBLAWAR2_PRELIM 0x00000000 124 125 #define CONFIG_SYS_BR3_PRELIM 0x00000000 126 #define CONFIG_SYS_OR3_PRELIM 0x00000000 127 #define CONFIG_SYS_LBLAWBAR3_PRELIM 0x00000000 128 #define CONFIG_SYS_LBLAWAR3_PRELIM 0x00000000 129 130 /* 131 * Monitor config 132 */ 133 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 134 135 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) 136 # define CONFIG_SYS_RAMBOOT 137 #else 138 # undef CONFIG_SYS_RAMBOOT 139 #endif 140 141 #define CONFIG_SYS_INIT_RAM_LOCK 1 142 #define CONFIG_SYS_INIT_RAM_ADDR 0x20000000 /* Initial RAM address */ 143 #define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM*/ 144 145 #define CONFIG_SYS_GBL_DATA_OFFSET \ 146 (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 147 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 148 149 /* Reserve 384 kB = 3 sect. for Mon */ 150 #define CONFIG_SYS_MONITOR_LEN (384 * 1024) 151 /* Reserve 512 kB for malloc */ 152 #define CONFIG_SYS_MALLOC_LEN (512 * 1024) 153 154 /* 155 * Serial Port 156 */ 157 #define CONFIG_CONS_INDEX 1 158 #define CONFIG_SYS_NS16550_SERIAL 159 #define CONFIG_SYS_NS16550_REG_SIZE 1 160 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 161 162 #define CONFIG_SYS_BAUDRATE_TABLE \ 163 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} 164 165 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500) 166 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600) 167 168 /* 169 * I2C 170 */ 171 #define CONFIG_SYS_I2C 172 #define CONFIG_SYS_I2C_FSL 173 #define CONFIG_SYS_FSL_I2C_SPEED 400000 174 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 175 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 176 177 /* I2C EEPROM, configuration for onboard EEPROMs 24C256 and 24C32 */ 178 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */ 179 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* 16 bit */ 180 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* 32 bytes/write */ 181 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 12 /* 10ms +/- 20% */ 182 183 /* I2C RTC */ 184 #define CONFIG_RTC_DS1337 /* use ds1337 rtc via i2c */ 185 #define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */ 186 187 /* I2C SYSMON (LM75) */ 188 #define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */ 189 #define CONFIG_DTT_SENSORS {0} /* Sensor addresses */ 190 #define CONFIG_SYS_DTT_MAX_TEMP 70 191 #define CONFIG_SYS_DTT_LOW_TEMP -30 192 #define CONFIG_SYS_DTT_HYSTERESIS 3 193 194 /* 195 * TSEC 196 */ 197 #define CONFIG_TSEC_ENET /* tsec ethernet support */ 198 #define CONFIG_MII 199 200 #define CONFIG_SYS_TSEC1_OFFSET 0x24000 201 #define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR + CONFIG_SYS_TSEC1_OFFSET) 202 #define CONFIG_SYS_TSEC2_OFFSET 0x25000 203 #define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR + CONFIG_SYS_TSEC2_OFFSET) 204 205 #if defined(CONFIG_TSEC_ENET) 206 207 #define CONFIG_TSEC1 1 208 #define CONFIG_TSEC1_NAME "TSEC0" 209 #define CONFIG_TSEC2 1 210 #define CONFIG_TSEC2_NAME "TSEC1" 211 #define TSEC1_PHY_ADDR 2 212 #define TSEC2_PHY_ADDR 1 213 #define TSEC1_PHYIDX 0 214 #define TSEC2_PHYIDX 0 215 #define TSEC1_FLAGS TSEC_GIGABIT 216 #define TSEC2_FLAGS TSEC_GIGABIT 217 218 /* Options are: TSEC[0-1] */ 219 #define CONFIG_ETHPRIME "TSEC0" 220 221 #endif /* CONFIG_TSEC_ENET */ 222 223 /* 224 * General PCI 225 * Addresses are mapped 1-1. 226 */ 227 228 #if defined(CONFIG_PCI) 229 230 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 231 232 /* PCI1 host bridge */ 233 #define CONFIG_SYS_PCI1_MEM_BASE 0x90000000 234 #define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE 235 #define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */ 236 #define CONFIG_SYS_PCI1_MMIO_BASE \ 237 (CONFIG_SYS_PCI1_MEM_BASE + CONFIG_SYS_PCI1_MEM_SIZE) 238 #define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE 239 #define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */ 240 #define CONFIG_SYS_PCI1_IO_BASE 0xe2000000 241 #define CONFIG_SYS_PCI1_IO_PHYS CONFIG_SYS_PCI1_IO_BASE 242 #define CONFIG_SYS_PCI1_IO_SIZE 0x1000000 /* 16M */ 243 244 #undef CONFIG_EEPRO100 245 #define CONFIG_EEPRO100 246 #undef CONFIG_TULIP 247 248 #if !defined(CONFIG_PCI_PNP) 249 #define PCI_ENET0_IOADDR CONFIG_SYS_PCI1_IO_BASE 250 #define PCI_ENET0_MEMADDR CONFIG_SYS_PCI1_MEM_BASE 251 #define PCI_IDSEL_NUMBER 0x1c /* slot0 (IDSEL) = 28 */ 252 #endif 253 254 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ 255 256 #endif /* CONFIG_PCI */ 257 258 /* 259 * Environment 260 */ 261 #define CONFIG_ENV_IS_IN_FLASH 1 262 #define CONFIG_ENV_ADDR \ 263 (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) 264 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) for env */ 265 #define CONFIG_ENV_SIZE 0x8000 /* 32K max size */ 266 #define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE) 267 #define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) 268 269 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 270 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 271 272 /* 273 * BOOTP options 274 */ 275 #define CONFIG_BOOTP_BOOTFILESIZE 276 #define CONFIG_BOOTP_BOOTPATH 277 #define CONFIG_BOOTP_GATEWAY 278 #define CONFIG_BOOTP_HOSTNAME 279 280 /* 281 * Command line configuration. 282 */ 283 #define CONFIG_CMD_DATE 284 #define CONFIG_CMD_DTT 285 #define CONFIG_CMD_EEPROM 286 #define CONFIG_CMD_JFFS2 287 #define CONFIG_CMD_REGINFO 288 289 #if defined(CONFIG_PCI) 290 #define CONFIG_CMD_PCI 291 #endif 292 293 /* 294 * Miscellaneous configurable options 295 */ 296 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 297 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 298 299 #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ 300 #define CONFIG_AUTO_COMPLETE /* add autocompletion support */ 301 302 #if defined(CONFIG_CMD_KGDB) 303 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 304 #else 305 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 306 #endif 307 308 /* Print Buffer Size */ 309 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) 310 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 311 /* Boot Argument Buffer Size */ 312 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE 313 314 #undef CONFIG_WATCHDOG /* watchdog disabled */ 315 316 /* 317 * For booting Linux, the board info and command line data 318 * have to be in the first 256 MB of memory, since this is 319 * the maximum mapped by the Linux kernel during initialization. 320 */ 321 /* Initial Memory map for Linux */ 322 #define CONFIG_SYS_BOOTMAPSZ (256 << 20) 323 324 #define CONFIG_SYS_HRCW_LOW (\ 325 HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ 326 HRCWL_DDR_TO_SCB_CLK_1X1 |\ 327 HRCWL_CSB_TO_CLKIN_4X1 |\ 328 HRCWL_VCO_1X2 |\ 329 HRCWL_CORE_TO_CSB_2X1) 330 331 #if defined(PCI_64BIT) 332 #define CONFIG_SYS_HRCW_HIGH (\ 333 HRCWH_PCI_HOST |\ 334 HRCWH_64_BIT_PCI |\ 335 HRCWH_PCI1_ARBITER_ENABLE |\ 336 HRCWH_PCI2_ARBITER_DISABLE |\ 337 HRCWH_CORE_ENABLE |\ 338 HRCWH_FROM_0X00000100 |\ 339 HRCWH_BOOTSEQ_DISABLE |\ 340 HRCWH_SW_WATCHDOG_DISABLE |\ 341 HRCWH_ROM_LOC_LOCAL_16BIT |\ 342 HRCWH_TSEC1M_IN_GMII |\ 343 HRCWH_TSEC2M_IN_GMII) 344 #else 345 #define CONFIG_SYS_HRCW_HIGH (\ 346 HRCWH_PCI_HOST |\ 347 HRCWH_32_BIT_PCI |\ 348 HRCWH_PCI1_ARBITER_ENABLE |\ 349 HRCWH_PCI2_ARBITER_DISABLE |\ 350 HRCWH_CORE_ENABLE |\ 351 HRCWH_FROM_0X00000100 |\ 352 HRCWH_BOOTSEQ_DISABLE |\ 353 HRCWH_SW_WATCHDOG_DISABLE |\ 354 HRCWH_ROM_LOC_LOCAL_16BIT |\ 355 HRCWH_TSEC1M_IN_GMII |\ 356 HRCWH_TSEC2M_IN_GMII) 357 #endif 358 359 /* System IO Config */ 360 #define CONFIG_SYS_SICRH 0 361 #define CONFIG_SYS_SICRL SICRL_LDP_A 362 363 /* i-cache and d-cache disabled */ 364 #define CONFIG_SYS_HID0_INIT 0x000000000 365 #define CONFIG_SYS_HID0_FINAL (CONFIG_SYS_HID0_INIT | \ 366 HID0_ENABLE_INSTRUCTION_CACHE) 367 #define CONFIG_SYS_HID2 HID2_HBE 368 369 #define CONFIG_HIGH_BATS 1 /* High BATs supported */ 370 371 /* DDR 0 - 512M */ 372 #define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE \ 373 | BATL_PP_RW \ 374 | BATL_MEMCOHERENCE) 375 #define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE \ 376 | BATU_BL_256M \ 377 | BATU_VS \ 378 | BATU_VP) 379 #define CONFIG_SYS_IBAT1L (CONFIG_SYS_SDRAM_BASE + 0x10000000 \ 380 | BATL_PP_RW \ 381 | BATL_MEMCOHERENCE) 382 #define CONFIG_SYS_IBAT1U (CONFIG_SYS_SDRAM_BASE + 0x10000000 \ 383 | BATU_BL_256M \ 384 | BATU_VS \ 385 | BATU_VP) 386 387 /* stack in DCACHE @ 512M (no backing mem) */ 388 #define CONFIG_SYS_IBAT2L (CONFIG_SYS_INIT_RAM_ADDR \ 389 | BATL_PP_RW \ 390 | BATL_MEMCOHERENCE) 391 #define CONFIG_SYS_IBAT2U (CONFIG_SYS_INIT_RAM_ADDR \ 392 | BATU_BL_128K \ 393 | BATU_VS \ 394 | BATU_VP) 395 396 /* PCI */ 397 #ifdef CONFIG_PCI 398 #define CONFIG_PCI_INDIRECT_BRIDGE 399 #define CONFIG_SYS_IBAT3L (CONFIG_SYS_PCI1_MEM_BASE \ 400 | BATL_PP_RW \ 401 | BATL_MEMCOHERENCE) 402 #define CONFIG_SYS_IBAT3U (CONFIG_SYS_PCI1_MEM_BASE \ 403 | BATU_BL_256M \ 404 | BATU_VS \ 405 | BATU_VP) 406 #define CONFIG_SYS_IBAT4L (CONFIG_SYS_PCI1_MMIO_BASE \ 407 | BATL_PP_RW \ 408 | BATL_MEMCOHERENCE \ 409 | BATL_GUARDEDSTORAGE) 410 #define CONFIG_SYS_IBAT4U (CONFIG_SYS_PCI1_MMIO_BASE \ 411 | BATU_BL_256M \ 412 | BATU_VS \ 413 | BATU_VP) 414 #define CONFIG_SYS_IBAT5L (CONFIG_SYS_PCI1_IO_BASE \ 415 | BATL_PP_RW \ 416 | BATL_CACHEINHIBIT \ 417 | BATL_GUARDEDSTORAGE) 418 #define CONFIG_SYS_IBAT5U (CONFIG_SYS_PCI1_IO_BASE \ 419 | BATU_BL_16M \ 420 | BATU_VS \ 421 | BATU_VP) 422 #else 423 #define CONFIG_SYS_IBAT3L (0) 424 #define CONFIG_SYS_IBAT3U (0) 425 #define CONFIG_SYS_IBAT4L (0) 426 #define CONFIG_SYS_IBAT4U (0) 427 #define CONFIG_SYS_IBAT5L (0) 428 #define CONFIG_SYS_IBAT5U (0) 429 #endif 430 431 /* IMMRBAR */ 432 #define CONFIG_SYS_IBAT6L (CONFIG_SYS_IMMR \ 433 | BATL_PP_RW \ 434 | BATL_CACHEINHIBIT \ 435 | BATL_GUARDEDSTORAGE) 436 #define CONFIG_SYS_IBAT6U (CONFIG_SYS_IMMR \ 437 | BATU_BL_1M \ 438 | BATU_VS \ 439 | BATU_VP) 440 441 /* FLASH */ 442 #define CONFIG_SYS_IBAT7L (CONFIG_SYS_FLASH_BASE \ 443 | BATL_PP_RW \ 444 | BATL_CACHEINHIBIT \ 445 | BATL_GUARDEDSTORAGE) 446 #define CONFIG_SYS_IBAT7U (CONFIG_SYS_FLASH_BASE \ 447 | BATU_BL_256M \ 448 | BATU_VS \ 449 | BATU_VP) 450 451 #define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L 452 #define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U 453 #define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L 454 #define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U 455 #define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L 456 #define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U 457 #define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L 458 #define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U 459 #define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L 460 #define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U 461 #define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L 462 #define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U 463 #define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L 464 #define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U 465 #define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L 466 #define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U 467 468 #if defined(CONFIG_CMD_KGDB) 469 #define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */ 470 #endif 471 472 /* 473 * Environment Configuration 474 */ 475 476 /* default location for tftp and bootm */ 477 #define CONFIG_LOADADDR 400000 478 479 #undef CONFIG_BOOTARGS /* the boot command will set bootargs */ 480 481 #define CONFIG_PREBOOT "echo;" \ 482 "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ 483 "echo" 484 485 #undef CONFIG_BOOTARGS 486 487 #define CONFIG_EXTRA_ENV_SETTINGS \ 488 "netdev=eth0\0" \ 489 "hostname=tqm834x\0" \ 490 "nfsargs=setenv bootargs root=/dev/nfs rw " \ 491 "nfsroot=${serverip}:${rootpath}\0" \ 492 "ramargs=setenv bootargs root=/dev/ram rw\0" \ 493 "addip=setenv bootargs ${bootargs} " \ 494 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ 495 ":${hostname}:${netdev}:off panic=1\0" \ 496 "addcons=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0" \ 497 "flash_nfs_old=run nfsargs addip addcons;" \ 498 "bootm ${kernel_addr}\0" \ 499 "flash_nfs=run nfsargs addip addcons;" \ 500 "bootm ${kernel_addr} - ${fdt_addr}\0" \ 501 "flash_self_old=run ramargs addip addcons;" \ 502 "bootm ${kernel_addr} ${ramdisk_addr}\0" \ 503 "flash_self=run ramargs addip addcons;" \ 504 "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \ 505 "net_nfs_old=tftp 400000 ${bootfile};" \ 506 "run nfsargs addip addcons;bootm\0" \ 507 "net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \ 508 "tftp ${fdt_addr_r} ${fdt_file}; " \ 509 "run nfsargs addip addcons; " \ 510 "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \ 511 "rootpath=/opt/eldk/ppc_6xx\0" \ 512 "bootfile=tqm834x/uImage\0" \ 513 "fdtfile=tqm834x/tqm834x.dtb\0" \ 514 "kernel_addr_r=400000\0" \ 515 "fdt_addr_r=600000\0" \ 516 "ramdisk_addr_r=800000\0" \ 517 "kernel_addr=800C0000\0" \ 518 "fdt_addr=800A0000\0" \ 519 "ramdisk_addr=80300000\0" \ 520 "u-boot=tqm834x/u-boot.bin\0" \ 521 "load=tftp 200000 ${u-boot}\0" \ 522 "update=protect off 80000000 +${filesize};" \ 523 "era 80000000 +${filesize};" \ 524 "cp.b 200000 80000000 ${filesize}\0" \ 525 "upd=run load update\0" \ 526 "" 527 528 #define CONFIG_BOOTCOMMAND "run flash_self" 529 530 /* 531 * JFFS2 partitions 532 */ 533 /* mtdparts command line support */ 534 #define CONFIG_CMD_MTDPARTS 535 #define CONFIG_MTD_DEVICE /* needed for mtdparts commands */ 536 #define CONFIG_FLASH_CFI_MTD 537 #define MTDIDS_DEFAULT "nor0=TQM834x-0" 538 539 /* default mtd partition table */ 540 #define MTDPARTS_DEFAULT "mtdparts=TQM834x-0:256k(u-boot),256k(env)," \ 541 "1m(kernel),2m(initrd)," \ 542 "-(user);" \ 543 544 #endif /* __CONFIG_H */ 545