1 /* 2 * Copyright 2011-2012 Freescale Semiconductor, Inc. 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 /* 8 * T4240 QDS board configuration file 9 */ 10 #ifndef __CONFIG_H 11 #define __CONFIG_H 12 13 #define CONFIG_T4240QDS 14 #define CONFIG_PHYS_64BIT 15 16 #define CONFIG_FSL_SATA_V2 17 #define CONFIG_PCIE4 18 #define CONFIG_FSL_CAAM /* Enable SEC/CAAM */ 19 20 #define CONFIG_ICS307_REFCLK_HZ 25000000 /* ICS307 ref clk freq */ 21 22 #ifdef CONFIG_RAMBOOT_PBL 23 #define CONFIG_SYS_FSL_PBL_PBI board/freescale/t4qds/t4_pbi.cfg 24 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t4qds/t4_rcw.cfg 25 #if !defined(CONFIG_NAND) && !defined(CONFIG_SDCARD) 26 #define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE 27 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc 28 #else 29 #define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT 30 #define CONFIG_SPL_ENV_SUPPORT 31 #define CONFIG_SPL_SERIAL_SUPPORT 32 #define CONFIG_SPL_FLUSH_IMAGE 33 #define CONFIG_SPL_TARGET "u-boot-with-spl.bin" 34 #define CONFIG_SPL_LIBGENERIC_SUPPORT 35 #define CONFIG_SPL_LIBCOMMON_SUPPORT 36 #define CONFIG_SPL_I2C_SUPPORT 37 #define CONFIG_SPL_DRIVERS_MISC_SUPPORT 38 #define CONFIG_FSL_LAW /* Use common FSL init code */ 39 #define CONFIG_SYS_TEXT_BASE 0x00201000 40 #define CONFIG_SPL_TEXT_BASE 0xFFFD8000 41 #define CONFIG_SPL_PAD_TO 0x40000 42 #define CONFIG_SPL_MAX_SIZE 0x28000 43 #define RESET_VECTOR_OFFSET 0x27FFC 44 #define BOOT_PAGE_OFFSET 0x27000 45 46 #ifdef CONFIG_NAND 47 #define CONFIG_SPL_NAND_SUPPORT 48 #define CONFIG_SYS_NAND_U_BOOT_SIZE (768 << 10) 49 #define CONFIG_SYS_NAND_U_BOOT_DST 0x00200000 50 #define CONFIG_SYS_NAND_U_BOOT_START 0x00200000 51 #define CONFIG_SYS_NAND_U_BOOT_OFFS (256 << 10) 52 #define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot-nand.lds" 53 #define CONFIG_SPL_NAND_BOOT 54 #endif 55 56 #ifdef CONFIG_SDCARD 57 #define CONFIG_RESET_VECTOR_ADDRESS 0x200FFC 58 #define CONFIG_SPL_MMC_SUPPORT 59 #define CONFIG_SPL_MMC_MINIMAL 60 #define CONFIG_SYS_MMC_U_BOOT_SIZE (768 << 10) 61 #define CONFIG_SYS_MMC_U_BOOT_DST 0x00200000 62 #define CONFIG_SYS_MMC_U_BOOT_START 0x00200000 63 #define CONFIG_SYS_MMC_U_BOOT_OFFS (260 << 10) 64 #ifndef CONFIG_SPL_BUILD 65 #define CONFIG_SYS_MPC85XX_NO_RESETVEC 66 #endif 67 #define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot.lds" 68 #define CONFIG_SPL_MMC_BOOT 69 #endif 70 71 #ifdef CONFIG_SPL_BUILD 72 #define CONFIG_SPL_SKIP_RELOCATE 73 #define CONFIG_SPL_COMMON_INIT_DDR 74 #define CONFIG_SYS_CCSR_DO_NOT_RELOCATE 75 #define CONFIG_SYS_NO_FLASH 76 #endif 77 78 #endif 79 #endif /* CONFIG_RAMBOOT_PBL */ 80 81 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE 82 /* Set 1M boot space */ 83 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000) 84 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \ 85 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR) 86 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc 87 #define CONFIG_SYS_NO_FLASH 88 #endif 89 90 #define CONFIG_SRIO_PCIE_BOOT_MASTER 91 #define CONFIG_DDR_ECC 92 93 #include "t4qds.h" 94 95 #ifdef CONFIG_SYS_NO_FLASH 96 #if !defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) && !defined(CONFIG_RAMBOOT_PBL) 97 #define CONFIG_ENV_IS_NOWHERE 98 #endif 99 #else 100 #define CONFIG_FLASH_CFI_DRIVER 101 #define CONFIG_SYS_FLASH_CFI 102 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 103 #endif 104 105 #if defined(CONFIG_SPIFLASH) 106 #define CONFIG_SYS_EXTRA_ENV_RELOC 107 #define CONFIG_ENV_IS_IN_SPI_FLASH 108 #define CONFIG_ENV_SPI_BUS 0 109 #define CONFIG_ENV_SPI_CS 0 110 #define CONFIG_ENV_SPI_MAX_HZ 10000000 111 #define CONFIG_ENV_SPI_MODE 0 112 #define CONFIG_ENV_SIZE 0x2000 /* 8KB */ 113 #define CONFIG_ENV_OFFSET 0x100000 /* 1MB */ 114 #define CONFIG_ENV_SECT_SIZE 0x10000 115 #elif defined(CONFIG_SDCARD) 116 #define CONFIG_SYS_EXTRA_ENV_RELOC 117 #define CONFIG_ENV_IS_IN_MMC 118 #define CONFIG_SYS_MMC_ENV_DEV 0 119 #define CONFIG_ENV_SIZE 0x2000 120 #define CONFIG_ENV_OFFSET (512 * 0x800) 121 #elif defined(CONFIG_NAND) 122 #define CONFIG_SYS_EXTRA_ENV_RELOC 123 #define CONFIG_ENV_IS_IN_NAND 124 #define CONFIG_ENV_SIZE 0x2000 125 #define CONFIG_ENV_OFFSET (10 * CONFIG_SYS_NAND_BLOCK_SIZE) 126 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) 127 #define CONFIG_ENV_IS_IN_REMOTE 128 #define CONFIG_ENV_ADDR 0xffe20000 129 #define CONFIG_ENV_SIZE 0x2000 130 #elif defined(CONFIG_ENV_IS_NOWHERE) 131 #define CONFIG_ENV_SIZE 0x2000 132 #else 133 #define CONFIG_ENV_IS_IN_FLASH 134 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) 135 #define CONFIG_ENV_SIZE 0x2000 136 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ 137 #endif 138 139 #define CONFIG_SYS_CLK_FREQ get_board_sys_clk() 140 #define CONFIG_DDR_CLK_FREQ get_board_ddr_clk() 141 142 #ifndef __ASSEMBLY__ 143 unsigned long get_board_sys_clk(void); 144 unsigned long get_board_ddr_clk(void); 145 #endif 146 147 /* EEPROM */ 148 #define CONFIG_ID_EEPROM 149 #define CONFIG_SYS_I2C_EEPROM_NXID 150 #define CONFIG_SYS_EEPROM_BUS_NUM 0 151 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 152 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 153 154 /* 155 * DDR Setup 156 */ 157 #define CONFIG_SYS_SPD_BUS_NUM 0 158 #define SPD_EEPROM_ADDRESS1 0x51 159 #define SPD_EEPROM_ADDRESS2 0x52 160 #define SPD_EEPROM_ADDRESS3 0x53 161 #define SPD_EEPROM_ADDRESS4 0x54 162 #define SPD_EEPROM_ADDRESS5 0x55 163 #define SPD_EEPROM_ADDRESS6 0x56 164 #define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1 /* for p3041/p5010 */ 165 #define CONFIG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */ 166 167 /* 168 * IFC Definitions 169 */ 170 #define CONFIG_SYS_NOR0_CSPR_EXT (0xf) 171 #define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS \ 172 + 0x8000000) | \ 173 CSPR_PORT_SIZE_16 | \ 174 CSPR_MSEL_NOR | \ 175 CSPR_V) 176 #define CONFIG_SYS_NOR1_CSPR_EXT (0xf) 177 #define CONFIG_SYS_NOR1_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \ 178 CSPR_PORT_SIZE_16 | \ 179 CSPR_MSEL_NOR | \ 180 CSPR_V) 181 #define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024) 182 /* NOR Flash Timing Params */ 183 #define CONFIG_SYS_NOR_CSOR CSOR_NAND_TRHZ_80 184 185 #define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \ 186 FTIM0_NOR_TEADC(0x5) | \ 187 FTIM0_NOR_TEAHC(0x5)) 188 #define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \ 189 FTIM1_NOR_TRAD_NOR(0x1A) |\ 190 FTIM1_NOR_TSEQRAD_NOR(0x13)) 191 #define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \ 192 FTIM2_NOR_TCH(0x4) | \ 193 FTIM2_NOR_TWPH(0x0E) | \ 194 FTIM2_NOR_TWP(0x1c)) 195 #define CONFIG_SYS_NOR_FTIM3 0x0 196 197 #define CONFIG_SYS_FLASH_QUIET_TEST 198 #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ 199 200 #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ 201 #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ 202 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 203 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 204 205 #define CONFIG_SYS_FLASH_EMPTY_INFO 206 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS \ 207 + 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS} 208 209 #define CONFIG_FSL_QIXIS /* use common QIXIS code */ 210 #define QIXIS_BASE 0xffdf0000 211 #define QIXIS_LBMAP_SWITCH 6 212 #define QIXIS_LBMAP_MASK 0x0f 213 #define QIXIS_LBMAP_SHIFT 0 214 #define QIXIS_LBMAP_DFLTBANK 0x00 215 #define QIXIS_LBMAP_ALTBANK 0x04 216 #define QIXIS_RST_CTL_RESET 0x83 217 #define QIXIS_RST_FORCE_MEM 0x1 218 #define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20 219 #define QIXIS_RCFG_CTL_RECONFIG_START 0x21 220 #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08 221 #define QIXIS_BRDCFG5 0x55 222 #define QIXIS_MUX_SDHC 2 223 #define QIXIS_MUX_SDHC_WIDTH8 1 224 #define QIXIS_BASE_PHYS (0xf00000000ull | QIXIS_BASE) 225 226 #define CONFIG_SYS_CSPR3_EXT (0xf) 227 #define CONFIG_SYS_CSPR3 (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \ 228 | CSPR_PORT_SIZE_8 \ 229 | CSPR_MSEL_GPCM \ 230 | CSPR_V) 231 #define CONFIG_SYS_AMASK3 IFC_AMASK(4*1024) 232 #define CONFIG_SYS_CSOR3 0x0 233 /* QIXIS Timing parameters for IFC CS3 */ 234 #define CONFIG_SYS_CS3_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \ 235 FTIM0_GPCM_TEADC(0x0e) | \ 236 FTIM0_GPCM_TEAHC(0x0e)) 237 #define CONFIG_SYS_CS3_FTIM1 (FTIM1_GPCM_TACO(0xff) | \ 238 FTIM1_GPCM_TRAD(0x3f)) 239 #define CONFIG_SYS_CS3_FTIM2 (FTIM2_GPCM_TCS(0x0e) | \ 240 FTIM2_GPCM_TCH(0x8) | \ 241 FTIM2_GPCM_TWP(0x1f)) 242 #define CONFIG_SYS_CS3_FTIM3 0x0 243 244 /* NAND Flash on IFC */ 245 #define CONFIG_NAND_FSL_IFC 246 #define CONFIG_SYS_NAND_BASE 0xff800000 247 #define CONFIG_SYS_NAND_BASE_PHYS (0xf00000000ull | CONFIG_SYS_NAND_BASE) 248 249 #define CONFIG_SYS_NAND_CSPR_EXT (0xf) 250 #define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ 251 | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \ 252 | CSPR_MSEL_NAND /* MSEL = NAND */ \ 253 | CSPR_V) 254 #define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024) 255 256 #define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \ 257 | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \ 258 | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \ 259 | CSOR_NAND_RAL_3 /* RAL = 2Byes */ \ 260 | CSOR_NAND_PGS_2K /* Page Size = 2K */ \ 261 | CSOR_NAND_SPRZ_64/* Spare size = 64 */ \ 262 | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/ 263 264 #define CONFIG_SYS_NAND_ONFI_DETECTION 265 266 /* ONFI NAND Flash mode0 Timing Params */ 267 #define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \ 268 FTIM0_NAND_TWP(0x18) | \ 269 FTIM0_NAND_TWCHT(0x07) | \ 270 FTIM0_NAND_TWH(0x0a)) 271 #define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \ 272 FTIM1_NAND_TWBE(0x39) | \ 273 FTIM1_NAND_TRR(0x0e) | \ 274 FTIM1_NAND_TRP(0x18)) 275 #define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \ 276 FTIM2_NAND_TREH(0x0a) | \ 277 FTIM2_NAND_TWHRE(0x1e)) 278 #define CONFIG_SYS_NAND_FTIM3 0x0 279 280 #define CONFIG_SYS_NAND_DDR_LAW 11 281 282 #define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } 283 #define CONFIG_SYS_MAX_NAND_DEVICE 1 284 #define CONFIG_CMD_NAND 285 286 #define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) 287 #define CONFIG_SYS_NAND_MAX_OOBFREE 2 288 #define CONFIG_SYS_NAND_MAX_ECCPOS 256 289 290 #if defined(CONFIG_NAND) 291 #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT 292 #define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR 293 #define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK 294 #define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR 295 #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0 296 #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1 297 #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2 298 #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3 299 #define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR0_CSPR_EXT 300 #define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR0_CSPR 301 #define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK 302 #define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR 303 #define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0 304 #define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1 305 #define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2 306 #define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3 307 #define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NOR1_CSPR_EXT 308 #define CONFIG_SYS_CSPR2 CONFIG_SYS_NOR1_CSPR 309 #define CONFIG_SYS_AMASK2 CONFIG_SYS_NOR_AMASK 310 #define CONFIG_SYS_CSOR2 CONFIG_SYS_NOR_CSOR 311 #define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NOR_FTIM0 312 #define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NOR_FTIM1 313 #define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NOR_FTIM2 314 #define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NOR_FTIM3 315 #else 316 #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT 317 #define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR 318 #define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK 319 #define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR 320 #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0 321 #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1 322 #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2 323 #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3 324 #define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR1_CSPR_EXT 325 #define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR1_CSPR 326 #define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK 327 #define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR 328 #define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0 329 #define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1 330 #define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2 331 #define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3 332 #define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NAND_CSPR_EXT 333 #define CONFIG_SYS_CSPR2 CONFIG_SYS_NAND_CSPR 334 #define CONFIG_SYS_AMASK2 CONFIG_SYS_NAND_AMASK 335 #define CONFIG_SYS_CSOR2 CONFIG_SYS_NAND_CSOR 336 #define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NAND_FTIM0 337 #define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NAND_FTIM1 338 #define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NAND_FTIM2 339 #define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NAND_FTIM3 340 #endif 341 342 #if defined(CONFIG_RAMBOOT_PBL) 343 #define CONFIG_SYS_RAMBOOT 344 #endif 345 346 /* I2C */ 347 #define CONFIG_SYS_FSL_I2C_SPEED 100000 /* I2C speed */ 348 #define CONFIG_SYS_FSL_I2C2_SPEED 100000 /* I2C2 speed */ 349 #define I2C_MUX_PCA_ADDR_PRI 0x77 /* I2C bus multiplexer,primary */ 350 #define I2C_MUX_PCA_ADDR_SEC 0x76 /* I2C bus multiplexer,secondary */ 351 352 #define I2C_MUX_CH_DEFAULT 0x8 353 #define I2C_MUX_CH_VOL_MONITOR 0xa 354 #define I2C_MUX_CH_VSC3316_FS 0xc 355 #define I2C_MUX_CH_VSC3316_BS 0xd 356 357 /* Voltage monitor on channel 2*/ 358 #define I2C_VOL_MONITOR_ADDR 0x40 359 #define I2C_VOL_MONITOR_BUS_V_OFFSET 0x2 360 #define I2C_VOL_MONITOR_BUS_V_OVF 0x1 361 #define I2C_VOL_MONITOR_BUS_V_SHIFT 3 362 363 /* VSC Crossbar switches */ 364 #define CONFIG_VSC_CROSSBAR 365 #define VSC3316_FSM_TX_ADDR 0x70 366 #define VSC3316_FSM_RX_ADDR 0x71 367 368 /* 369 * RapidIO 370 */ 371 372 /* 373 * for slave u-boot IMAGE instored in master memory space, 374 * PHYS must be aligned based on the SIZE 375 */ 376 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull 377 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull 378 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x100000 /* 1M */ 379 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull 380 /* 381 * for slave UCODE and ENV instored in master memory space, 382 * PHYS must be aligned based on the SIZE 383 */ 384 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull 385 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull 386 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */ 387 388 /* slave core release by master*/ 389 #define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4 390 #define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */ 391 392 /* 393 * SRIO_PCIE_BOOT - SLAVE 394 */ 395 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE 396 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000 397 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \ 398 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR) 399 #endif 400 /* 401 * eSPI - Enhanced SPI 402 */ 403 #define CONFIG_SF_DEFAULT_SPEED 10000000 404 #define CONFIG_SF_DEFAULT_MODE 0 405 406 /* Qman/Bman */ 407 #ifndef CONFIG_NOBQFMAN 408 #define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */ 409 #define CONFIG_SYS_BMAN_NUM_PORTALS 50 410 #define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000 411 #define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull 412 #define CONFIG_SYS_BMAN_MEM_SIZE 0x02000000 413 #define CONFIG_SYS_BMAN_SP_CENA_SIZE 0x4000 414 #define CONFIG_SYS_BMAN_SP_CINH_SIZE 0x1000 415 #define CONFIG_SYS_BMAN_CENA_BASE CONFIG_SYS_BMAN_MEM_BASE 416 #define CONFIG_SYS_BMAN_CENA_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) 417 #define CONFIG_SYS_BMAN_CINH_BASE (CONFIG_SYS_BMAN_MEM_BASE + \ 418 CONFIG_SYS_BMAN_CENA_SIZE) 419 #define CONFIG_SYS_BMAN_CINH_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) 420 #define CONFIG_SYS_BMAN_SWP_ISDR_REG 0xE08 421 #define CONFIG_SYS_QMAN_NUM_PORTALS 50 422 #define CONFIG_SYS_QMAN_MEM_BASE 0xf6000000 423 #define CONFIG_SYS_QMAN_MEM_PHYS 0xff6000000ull 424 #define CONFIG_SYS_QMAN_MEM_SIZE 0x02000000 425 #define CONFIG_SYS_QMAN_SP_CENA_SIZE 0x4000 426 #define CONFIG_SYS_QMAN_SP_CINH_SIZE 0x1000 427 #define CONFIG_SYS_QMAN_CENA_BASE CONFIG_SYS_QMAN_MEM_BASE 428 #define CONFIG_SYS_QMAN_CENA_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) 429 #define CONFIG_SYS_QMAN_CINH_BASE (CONFIG_SYS_QMAN_MEM_BASE + \ 430 CONFIG_SYS_QMAN_CENA_SIZE) 431 #define CONFIG_SYS_QMAN_CINH_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) 432 #define CONFIG_SYS_QMAN_SWP_ISDR_REG 0xE08 433 434 #define CONFIG_SYS_DPAA_FMAN 435 #define CONFIG_SYS_DPAA_PME 436 #define CONFIG_SYS_PMAN 437 #define CONFIG_SYS_DPAA_DCE 438 #define CONFIG_SYS_DPAA_RMAN 439 #define CONFIG_SYS_INTERLAKEN 440 441 /* Default address of microcode for the Linux Fman driver */ 442 #if defined(CONFIG_SPIFLASH) 443 /* 444 * env is stored at 0x100000, sector size is 0x10000, ucode is stored after 445 * env, so we got 0x110000. 446 */ 447 #define CONFIG_SYS_QE_FW_IN_SPIFLASH 448 #define CONFIG_SYS_FMAN_FW_ADDR 0x110000 449 #elif defined(CONFIG_SDCARD) 450 /* 451 * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is 452 * about 1MB (2048 blocks), Env is stored after the image, and the env size is 453 * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080. 454 */ 455 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC 456 #define CONFIG_SYS_FMAN_FW_ADDR (512 * 0x820) 457 #elif defined(CONFIG_NAND) 458 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND 459 #define CONFIG_SYS_FMAN_FW_ADDR (11 * CONFIG_SYS_NAND_BLOCK_SIZE) 460 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) 461 /* 462 * Slave has no ucode locally, it can fetch this from remote. When implementing 463 * in two corenet boards, slave's ucode could be stored in master's memory 464 * space, the address can be mapped from slave TLB->slave LAW-> 465 * slave SRIO or PCIE outbound window->master inbound window-> 466 * master LAW->the ucode address in master's memory space. 467 */ 468 #define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE 469 #define CONFIG_SYS_FMAN_FW_ADDR 0xFFE00000 470 #else 471 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR 472 #define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000 473 #endif 474 #define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 475 #define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) 476 #endif /* CONFIG_NOBQFMAN */ 477 478 #ifdef CONFIG_SYS_DPAA_FMAN 479 #define CONFIG_FMAN_ENET 480 #define CONFIG_PHYLIB_10G 481 #define CONFIG_PHY_VITESSE 482 #define CONFIG_PHY_TERANETICS 483 #define SGMII_CARD_PORT1_PHY_ADDR 0x1C 484 #define SGMII_CARD_PORT2_PHY_ADDR 0x1D 485 #define SGMII_CARD_PORT3_PHY_ADDR 0x1E 486 #define SGMII_CARD_PORT4_PHY_ADDR 0x1F 487 #define FM1_10GEC1_PHY_ADDR 0x0 488 #define FM1_10GEC2_PHY_ADDR 0x1 489 #define FM2_10GEC1_PHY_ADDR 0x2 490 #define FM2_10GEC2_PHY_ADDR 0x3 491 #endif 492 493 /* SATA */ 494 #ifdef CONFIG_FSL_SATA_V2 495 #define CONFIG_LIBATA 496 #define CONFIG_FSL_SATA 497 498 #define CONFIG_SYS_SATA_MAX_DEVICE 2 499 #define CONFIG_SATA1 500 #define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR 501 #define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA 502 #define CONFIG_SATA2 503 #define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR 504 #define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA 505 506 #define CONFIG_LBA48 507 #define CONFIG_CMD_SATA 508 #define CONFIG_DOS_PARTITION 509 #endif 510 511 #ifdef CONFIG_FMAN_ENET 512 #define CONFIG_MII /* MII PHY management */ 513 #define CONFIG_ETHPRIME "FM1@DTSEC1" 514 #define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ 515 #endif 516 517 /* Hash command with SHA acceleration supported in hardware */ 518 #ifdef CONFIG_FSL_CAAM 519 #define CONFIG_CMD_HASH 520 #define CONFIG_SHA_HW_ACCEL 521 #endif 522 523 /* 524 * USB 525 */ 526 #define CONFIG_USB_STORAGE 527 #define CONFIG_USB_EHCI 528 #define CONFIG_USB_EHCI_FSL 529 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET 530 #define CONFIG_HAS_FSL_DR_USB 531 532 #define CONFIG_MMC 533 534 #ifdef CONFIG_MMC 535 #define CONFIG_FSL_ESDHC 536 #define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR 537 #define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT 538 #define CONFIG_GENERIC_MMC 539 #define CONFIG_DOS_PARTITION 540 #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33 541 #define CONFIG_ESDHC_DETECT_QUIRK \ 542 (!(readb(QIXIS_BASE + QIXIS_BRDCFG5) & QIXIS_MUX_SDHC) || \ 543 IS_SVR_REV(get_svr(), 1, 0)) 544 #define CONFIG_ESDHC_DETECT_8_BIT_QUIRK \ 545 (!(readb(QIXIS_BASE + QIXIS_BRDCFG5) & QIXIS_MUX_SDHC_WIDTH8)) 546 #endif 547 548 #define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ 549 550 #define __USB_PHY_TYPE utmi 551 552 /* 553 * T4240 has 3 DDR controllers. Default to 3-way interleaving. It can be 554 * 3way_1KB, 3way_4KB, 3way_8KB. T4160 has 2 DDR controllers. Default to 2-way 555 * interleaving. It can be cacheline, page, bank, superbank. 556 * See doc/README.fsl-ddr for details. 557 */ 558 #ifdef CONFIG_PPC_T4240 559 #define CTRL_INTLV_PREFERED 3way_4KB 560 #else 561 #define CTRL_INTLV_PREFERED cacheline 562 #endif 563 564 #define CONFIG_EXTRA_ENV_SETTINGS \ 565 "hwconfig=fsl_ddr:" \ 566 "ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) "," \ 567 "bank_intlv=auto;" \ 568 "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\ 569 "netdev=eth0\0" \ 570 "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ 571 "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \ 572 "tftpflash=tftpboot $loadaddr $uboot && " \ 573 "protect off $ubootaddr +$filesize && " \ 574 "erase $ubootaddr +$filesize && " \ 575 "cp.b $loadaddr $ubootaddr $filesize && " \ 576 "protect on $ubootaddr +$filesize && " \ 577 "cmp.b $loadaddr $ubootaddr $filesize\0" \ 578 "consoledev=ttyS0\0" \ 579 "ramdiskaddr=2000000\0" \ 580 "ramdiskfile=t4240qds/ramdisk.uboot\0" \ 581 "fdtaddr=c00000\0" \ 582 "fdtfile=t4240qds/t4240qds.dtb\0" \ 583 "bdev=sda3\0" 584 585 #define CONFIG_HVBOOT \ 586 "setenv bootargs config-addr=0x60000000; " \ 587 "bootm 0x01000000 - 0x00f00000" 588 589 #define CONFIG_ALU \ 590 "setenv bootargs root=/dev/$bdev rw " \ 591 "console=$consoledev,$baudrate $othbootargs;" \ 592 "cpu 1 release 0x01000000 - - -;" \ 593 "cpu 2 release 0x01000000 - - -;" \ 594 "cpu 3 release 0x01000000 - - -;" \ 595 "cpu 4 release 0x01000000 - - -;" \ 596 "cpu 5 release 0x01000000 - - -;" \ 597 "cpu 6 release 0x01000000 - - -;" \ 598 "cpu 7 release 0x01000000 - - -;" \ 599 "go 0x01000000" 600 601 #define CONFIG_LINUX \ 602 "setenv bootargs root=/dev/ram rw " \ 603 "console=$consoledev,$baudrate $othbootargs;" \ 604 "setenv ramdiskaddr 0x02000000;" \ 605 "setenv fdtaddr 0x00c00000;" \ 606 "setenv loadaddr 0x1000000;" \ 607 "bootm $loadaddr $ramdiskaddr $fdtaddr" 608 609 #define CONFIG_HDBOOT \ 610 "setenv bootargs root=/dev/$bdev rw " \ 611 "console=$consoledev,$baudrate $othbootargs;" \ 612 "tftp $loadaddr $bootfile;" \ 613 "tftp $fdtaddr $fdtfile;" \ 614 "bootm $loadaddr - $fdtaddr" 615 616 #define CONFIG_NFSBOOTCOMMAND \ 617 "setenv bootargs root=/dev/nfs rw " \ 618 "nfsroot=$serverip:$rootpath " \ 619 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 620 "console=$consoledev,$baudrate $othbootargs;" \ 621 "tftp $loadaddr $bootfile;" \ 622 "tftp $fdtaddr $fdtfile;" \ 623 "bootm $loadaddr - $fdtaddr" 624 625 #define CONFIG_RAMBOOTCOMMAND \ 626 "setenv bootargs root=/dev/ram rw " \ 627 "console=$consoledev,$baudrate $othbootargs;" \ 628 "tftp $ramdiskaddr $ramdiskfile;" \ 629 "tftp $loadaddr $bootfile;" \ 630 "tftp $fdtaddr $fdtfile;" \ 631 "bootm $loadaddr $ramdiskaddr $fdtaddr" 632 633 #define CONFIG_BOOTCOMMAND CONFIG_LINUX 634 635 #include <asm/fsl_secure_boot.h> 636 637 #endif /* __CONFIG_H */ 638