1 /* 2 * Copyright 2014 Freescale Semiconductor, Inc. 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 /* 8 * T2080 RDB/PCIe board configuration file 9 */ 10 11 #ifndef __T2080RDB_H 12 #define __T2080RDB_H 13 14 #define CONFIG_ICS307_REFCLK_HZ 25000000 /* ICS307 ref clk freq */ 15 #define CONFIG_FSL_SATA_V2 16 17 /* High Level Configuration Options */ 18 #define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */ 19 #define CONFIG_MP /* support multiple processors */ 20 #define CONFIG_ENABLE_36BIT_PHYS 21 22 #ifdef CONFIG_PHYS_64BIT 23 #define CONFIG_ADDR_MAP 1 24 #define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */ 25 #endif 26 27 #define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */ 28 #define CONFIG_SYS_NUM_CPC CONFIG_SYS_NUM_DDR_CTLRS 29 #define CONFIG_ENV_OVERWRITE 30 31 #ifdef CONFIG_RAMBOOT_PBL 32 #define CONFIG_SYS_FSL_PBL_PBI board/freescale/t208xrdb/t2080_pbi.cfg 33 34 #define CONFIG_SPL_FLUSH_IMAGE 35 #define CONFIG_SPL_TARGET "u-boot-with-spl.bin" 36 #define CONFIG_SYS_TEXT_BASE 0x00201000 37 #define CONFIG_SPL_TEXT_BASE 0xFFFD8000 38 #define CONFIG_SPL_PAD_TO 0x40000 39 #define CONFIG_SPL_MAX_SIZE 0x28000 40 #define RESET_VECTOR_OFFSET 0x27FFC 41 #define BOOT_PAGE_OFFSET 0x27000 42 #ifdef CONFIG_SPL_BUILD 43 #define CONFIG_SPL_SKIP_RELOCATE 44 #define CONFIG_SPL_COMMON_INIT_DDR 45 #define CONFIG_SYS_CCSR_DO_NOT_RELOCATE 46 #endif 47 48 #ifdef CONFIG_NAND 49 #define CONFIG_SYS_NAND_U_BOOT_SIZE (768 << 10) 50 #define CONFIG_SYS_NAND_U_BOOT_DST 0x00200000 51 #define CONFIG_SYS_NAND_U_BOOT_START 0x00200000 52 #define CONFIG_SYS_NAND_U_BOOT_OFFS (256 << 10) 53 #define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot-nand.lds" 54 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xrdb/t2080_nand_rcw.cfg 55 #define CONFIG_SPL_NAND_BOOT 56 #endif 57 58 #ifdef CONFIG_SPIFLASH 59 #define CONFIG_RESET_VECTOR_ADDRESS 0x200FFC 60 #define CONFIG_SPL_SPI_FLASH_MINIMAL 61 #define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE (768 << 10) 62 #define CONFIG_SYS_SPI_FLASH_U_BOOT_DST (0x00200000) 63 #define CONFIG_SYS_SPI_FLASH_U_BOOT_START (0x00200000) 64 #define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS (256 << 10) 65 #define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot.lds" 66 #ifndef CONFIG_SPL_BUILD 67 #define CONFIG_SYS_MPC85XX_NO_RESETVEC 68 #endif 69 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xrdb/t2080_spi_rcw.cfg 70 #define CONFIG_SPL_SPI_BOOT 71 #endif 72 73 #ifdef CONFIG_SDCARD 74 #define CONFIG_RESET_VECTOR_ADDRESS 0x200FFC 75 #define CONFIG_SPL_MMC_MINIMAL 76 #define CONFIG_SYS_MMC_U_BOOT_SIZE (768 << 10) 77 #define CONFIG_SYS_MMC_U_BOOT_DST (0x00200000) 78 #define CONFIG_SYS_MMC_U_BOOT_START (0x00200000) 79 #define CONFIG_SYS_MMC_U_BOOT_OFFS (260 << 10) 80 #define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot.lds" 81 #ifndef CONFIG_SPL_BUILD 82 #define CONFIG_SYS_MPC85XX_NO_RESETVEC 83 #endif 84 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xrdb/t2080_sd_rcw.cfg 85 #define CONFIG_SPL_MMC_BOOT 86 #endif 87 88 #endif /* CONFIG_RAMBOOT_PBL */ 89 90 #define CONFIG_SRIO_PCIE_BOOT_MASTER 91 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE 92 /* Set 1M boot space */ 93 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000) 94 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \ 95 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR) 96 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc 97 #endif 98 99 #ifndef CONFIG_SYS_TEXT_BASE 100 #define CONFIG_SYS_TEXT_BASE 0xeff40000 101 #endif 102 103 #ifndef CONFIG_RESET_VECTOR_ADDRESS 104 #define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc 105 #endif 106 107 /* 108 * These can be toggled for performance analysis, otherwise use default. 109 */ 110 #define CONFIG_SYS_CACHE_STASHING 111 #define CONFIG_BTB /* toggle branch predition */ 112 #define CONFIG_DDR_ECC 113 #ifdef CONFIG_DDR_ECC 114 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER 115 #define CONFIG_MEM_INIT_VALUE 0xdeadbeef 116 #endif 117 118 #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ 119 #define CONFIG_SYS_MEMTEST_END 0x00400000 120 #define CONFIG_SYS_ALT_MEMTEST 121 122 #ifdef CONFIG_MTD_NOR_FLASH 123 #define CONFIG_FLASH_CFI_DRIVER 124 #define CONFIG_SYS_FLASH_CFI 125 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 126 #endif 127 128 #if defined(CONFIG_SPIFLASH) 129 #define CONFIG_SYS_EXTRA_ENV_RELOC 130 #define CONFIG_ENV_IS_IN_SPI_FLASH 131 #define CONFIG_ENV_SPI_BUS 0 132 #define CONFIG_ENV_SPI_CS 0 133 #define CONFIG_ENV_SPI_MAX_HZ 10000000 134 #define CONFIG_ENV_SPI_MODE 0 135 #define CONFIG_ENV_SIZE 0x2000 /* 8KB */ 136 #define CONFIG_ENV_OFFSET 0x100000 /* 1MB */ 137 #define CONFIG_ENV_SECT_SIZE 0x10000 138 #elif defined(CONFIG_SDCARD) 139 #define CONFIG_SYS_EXTRA_ENV_RELOC 140 #define CONFIG_ENV_IS_IN_MMC 141 #define CONFIG_SYS_MMC_ENV_DEV 0 142 #define CONFIG_ENV_SIZE 0x2000 143 #define CONFIG_ENV_OFFSET (512 * 0x800) 144 #elif defined(CONFIG_NAND) 145 #define CONFIG_SYS_EXTRA_ENV_RELOC 146 #define CONFIG_ENV_IS_IN_NAND 147 #define CONFIG_ENV_SIZE 0x2000 148 #define CONFIG_ENV_OFFSET (2 * CONFIG_SYS_NAND_BLOCK_SIZE) 149 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) 150 #define CONFIG_ENV_IS_IN_REMOTE 151 #define CONFIG_ENV_ADDR 0xffe20000 152 #define CONFIG_ENV_SIZE 0x2000 153 #elif defined(CONFIG_ENV_IS_NOWHERE) 154 #define CONFIG_ENV_SIZE 0x2000 155 #else 156 #define CONFIG_ENV_IS_IN_FLASH 157 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) 158 #define CONFIG_ENV_SIZE 0x2000 159 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ 160 #endif 161 162 #ifndef __ASSEMBLY__ 163 unsigned long get_board_sys_clk(void); 164 unsigned long get_board_ddr_clk(void); 165 #endif 166 167 #define CONFIG_SYS_CLK_FREQ 66660000 168 #define CONFIG_DDR_CLK_FREQ 133330000 169 170 /* 171 * Config the L3 Cache as L3 SRAM 172 */ 173 #define CONFIG_SYS_INIT_L3_ADDR 0xFFFC0000 174 #define CONFIG_SYS_L3_SIZE (512 << 10) 175 #define CONFIG_SPL_GD_ADDR (CONFIG_SYS_INIT_L3_ADDR + 32 * 1024) 176 #ifdef CONFIG_RAMBOOT_PBL 177 #define CONFIG_ENV_ADDR (CONFIG_SPL_GD_ADDR + 4 * 1024) 178 #endif 179 #define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SPL_GD_ADDR + 12 * 1024) 180 #define CONFIG_SPL_RELOC_MALLOC_SIZE (50 << 10) 181 #define CONFIG_SPL_RELOC_STACK (CONFIG_SPL_GD_ADDR + 64 * 1024) 182 #define CONFIG_SPL_RELOC_STACK_SIZE (22 << 10) 183 184 #define CONFIG_SYS_DCSRBAR 0xf0000000 185 #define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull 186 187 /* EEPROM */ 188 #define CONFIG_ID_EEPROM 189 #define CONFIG_SYS_I2C_EEPROM_NXID 190 #define CONFIG_SYS_EEPROM_BUS_NUM 0 191 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 192 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 193 194 /* 195 * DDR Setup 196 */ 197 #define CONFIG_VERY_BIG_RAM 198 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 199 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 200 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 201 #define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR) 202 #define CONFIG_DDR_SPD 203 #undef CONFIG_FSL_DDR_INTERACTIVE 204 #define CONFIG_SYS_SPD_BUS_NUM 0 205 #define CONFIG_SYS_SDRAM_SIZE 2048 /* for fixed parameter use */ 206 #define SPD_EEPROM_ADDRESS1 0x51 207 #define SPD_EEPROM_ADDRESS2 0x52 208 #define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1 209 #define CTRL_INTLV_PREFERED cacheline 210 211 /* 212 * IFC Definitions 213 */ 214 #define CONFIG_SYS_FLASH_BASE 0xe8000000 215 #define CONFIG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CONFIG_SYS_FLASH_BASE) 216 #define CONFIG_SYS_NOR0_CSPR_EXT (0xf) 217 #define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \ 218 CSPR_PORT_SIZE_16 | \ 219 CSPR_MSEL_NOR | \ 220 CSPR_V) 221 #define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024) 222 223 /* NOR Flash Timing Params */ 224 #define CONFIG_SYS_NOR_CSOR CSOR_NAND_TRHZ_80 225 226 #define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \ 227 FTIM0_NOR_TEADC(0x5) | \ 228 FTIM0_NOR_TEAHC(0x5)) 229 #define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \ 230 FTIM1_NOR_TRAD_NOR(0x1A) |\ 231 FTIM1_NOR_TSEQRAD_NOR(0x13)) 232 #define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \ 233 FTIM2_NOR_TCH(0x4) | \ 234 FTIM2_NOR_TWPH(0x0E) | \ 235 FTIM2_NOR_TWP(0x1c)) 236 #define CONFIG_SYS_NOR_FTIM3 0x0 237 238 #define CONFIG_SYS_FLASH_QUIET_TEST 239 #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ 240 241 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 242 #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ 243 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 244 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 245 #define CONFIG_SYS_FLASH_EMPTY_INFO 246 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS } 247 248 /* CPLD on IFC */ 249 #define CONFIG_SYS_CPLD_BASE 0xffdf0000 250 #define CONFIG_SYS_CPLD_BASE_PHYS (0xf00000000ull | CONFIG_SYS_CPLD_BASE) 251 #define CONFIG_SYS_CSPR2_EXT (0xf) 252 #define CONFIG_SYS_CSPR2 (CSPR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE) \ 253 | CSPR_PORT_SIZE_8 \ 254 | CSPR_MSEL_GPCM \ 255 | CSPR_V) 256 #define CONFIG_SYS_AMASK2 IFC_AMASK(64*1024) 257 #define CONFIG_SYS_CSOR2 0x0 258 259 /* CPLD Timing parameters for IFC CS2 */ 260 #define CONFIG_SYS_CS2_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \ 261 FTIM0_GPCM_TEADC(0x0e) | \ 262 FTIM0_GPCM_TEAHC(0x0e)) 263 #define CONFIG_SYS_CS2_FTIM1 (FTIM1_GPCM_TACO(0x0e) | \ 264 FTIM1_GPCM_TRAD(0x1f)) 265 #define CONFIG_SYS_CS2_FTIM2 (FTIM2_GPCM_TCS(0x0e) | \ 266 FTIM2_GPCM_TCH(0x8) | \ 267 FTIM2_GPCM_TWP(0x1f)) 268 #define CONFIG_SYS_CS2_FTIM3 0x0 269 270 /* NAND Flash on IFC */ 271 #define CONFIG_NAND_FSL_IFC 272 #define CONFIG_SYS_NAND_BASE 0xff800000 273 #define CONFIG_SYS_NAND_BASE_PHYS (0xf00000000ull | CONFIG_SYS_NAND_BASE) 274 275 #define CONFIG_SYS_NAND_CSPR_EXT (0xf) 276 #define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ 277 | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \ 278 | CSPR_MSEL_NAND /* MSEL = NAND */ \ 279 | CSPR_V) 280 #define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024) 281 282 #define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \ 283 | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \ 284 | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \ 285 | CSOR_NAND_RAL_3 /* RAL = 2Byes */ \ 286 | CSOR_NAND_PGS_2K /* Page Size = 2K */\ 287 | CSOR_NAND_SPRZ_64 /* Spare size = 64 */\ 288 | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/ 289 290 #define CONFIG_SYS_NAND_ONFI_DETECTION 291 292 /* ONFI NAND Flash mode0 Timing Params */ 293 #define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \ 294 FTIM0_NAND_TWP(0x18) | \ 295 FTIM0_NAND_TWCHT(0x07) | \ 296 FTIM0_NAND_TWH(0x0a)) 297 #define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \ 298 FTIM1_NAND_TWBE(0x39) | \ 299 FTIM1_NAND_TRR(0x0e) | \ 300 FTIM1_NAND_TRP(0x18)) 301 #define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \ 302 FTIM2_NAND_TREH(0x0a) | \ 303 FTIM2_NAND_TWHRE(0x1e)) 304 #define CONFIG_SYS_NAND_FTIM3 0x0 305 306 #define CONFIG_SYS_NAND_DDR_LAW 11 307 #define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } 308 #define CONFIG_SYS_MAX_NAND_DEVICE 1 309 #define CONFIG_CMD_NAND 310 #define CONFIG_SYS_NAND_BLOCK_SIZE (512 * 1024) 311 312 #if defined(CONFIG_NAND) 313 #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT 314 #define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR 315 #define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK 316 #define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR 317 #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0 318 #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1 319 #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2 320 #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3 321 #define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR0_CSPR_EXT 322 #define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR0_CSPR 323 #define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK 324 #define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR 325 #define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0 326 #define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1 327 #define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2 328 #define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3 329 #else 330 #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT 331 #define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR 332 #define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK 333 #define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR 334 #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0 335 #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1 336 #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2 337 #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3 338 #define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NAND_CSPR_EXT 339 #define CONFIG_SYS_CSPR1 CONFIG_SYS_NAND_CSPR 340 #define CONFIG_SYS_AMASK1 CONFIG_SYS_NAND_AMASK 341 #define CONFIG_SYS_CSOR1 CONFIG_SYS_NAND_CSOR 342 #define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NAND_FTIM0 343 #define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NAND_FTIM1 344 #define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NAND_FTIM2 345 #define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NAND_FTIM3 346 #endif 347 348 #if defined(CONFIG_RAMBOOT_PBL) 349 #define CONFIG_SYS_RAMBOOT 350 #endif 351 352 #ifdef CONFIG_SPL_BUILD 353 #define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE 354 #else 355 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 356 #endif 357 358 #define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */ 359 #define CONFIG_MISC_INIT_R 360 #define CONFIG_HWCONFIG 361 362 /* define to use L1 as initial stack */ 363 #define CONFIG_L1_INIT_RAM 364 #define CONFIG_SYS_INIT_RAM_LOCK 365 #define CONFIG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */ 366 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf 367 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW 0xfe03c000 368 /* The assembler doesn't like typecast */ 369 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \ 370 ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \ 371 CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW) 372 #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 373 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ 374 GENERATED_GBL_DATA_SIZE) 375 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 376 #define CONFIG_SYS_MONITOR_LEN (768 * 1024) 377 #define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024) 378 379 /* 380 * Serial Port 381 */ 382 #define CONFIG_CONS_INDEX 1 383 #define CONFIG_SYS_NS16550_SERIAL 384 #define CONFIG_SYS_NS16550_REG_SIZE 1 385 #define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2) 386 #define CONFIG_SYS_BAUDRATE_TABLE \ 387 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} 388 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500) 389 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600) 390 #define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500) 391 #define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600) 392 393 /* 394 * I2C 395 */ 396 #define CONFIG_SYS_I2C 397 #define CONFIG_SYS_I2C_FSL 398 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 399 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F 400 #define CONFIG_SYS_FSL_I2C3_SLAVE 0x7F 401 #define CONFIG_SYS_FSL_I2C4_SLAVE 0x7F 402 #define CONFIG_SYS_FSL_I2C_OFFSET 0x118000 403 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100 404 #define CONFIG_SYS_FSL_I2C3_OFFSET 0x119000 405 #define CONFIG_SYS_FSL_I2C4_OFFSET 0x119100 406 #define CONFIG_SYS_FSL_I2C_SPEED 100000 407 #define CONFIG_SYS_FSL_I2C2_SPEED 100000 408 #define CONFIG_SYS_FSL_I2C3_SPEED 100000 409 #define CONFIG_SYS_FSL_I2C4_SPEED 100000 410 #define I2C_MUX_PCA_ADDR_PRI 0x77 /* I2C bus multiplexer,primary */ 411 #define I2C_MUX_PCA_ADDR_SEC1 0x75 /* I2C bus multiplexer,secondary 1 */ 412 #define I2C_MUX_PCA_ADDR_SEC2 0x76 /* I2C bus multiplexer,secondary 2 */ 413 #define I2C_MUX_CH_DEFAULT 0x8 414 415 #define I2C_MUX_CH_VOL_MONITOR 0xa 416 417 #define CONFIG_VID_FLS_ENV "t208xrdb_vdd_mv" 418 #ifndef CONFIG_SPL_BUILD 419 #define CONFIG_VID 420 #endif 421 #define CONFIG_VOL_MONITOR_IR36021_SET 422 #define CONFIG_VOL_MONITOR_IR36021_READ 423 /* The lowest and highest voltage allowed for T208xRDB */ 424 #define VDD_MV_MIN 819 425 #define VDD_MV_MAX 1212 426 427 /* 428 * RapidIO 429 */ 430 #define CONFIG_SYS_SRIO1_MEM_VIRT 0xa0000000 431 #define CONFIG_SYS_SRIO1_MEM_PHYS 0xc20000000ull 432 #define CONFIG_SYS_SRIO1_MEM_SIZE 0x10000000 /* 256M */ 433 #define CONFIG_SYS_SRIO2_MEM_VIRT 0xb0000000 434 #define CONFIG_SYS_SRIO2_MEM_PHYS 0xc30000000ull 435 #define CONFIG_SYS_SRIO2_MEM_SIZE 0x10000000 /* 256M */ 436 /* 437 * for slave u-boot IMAGE instored in master memory space, 438 * PHYS must be aligned based on the SIZE 439 */ 440 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull 441 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull 442 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x100000 /* 1M */ 443 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull 444 /* 445 * for slave UCODE and ENV instored in master memory space, 446 * PHYS must be aligned based on the SIZE 447 */ 448 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull 449 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull 450 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */ 451 452 /* slave core release by master*/ 453 #define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4 454 #define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */ 455 456 /* 457 * SRIO_PCIE_BOOT - SLAVE 458 */ 459 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE 460 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000 461 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \ 462 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR) 463 #endif 464 465 /* 466 * eSPI - Enhanced SPI 467 */ 468 #ifdef CONFIG_SPI_FLASH 469 #define CONFIG_SPI_FLASH_BAR 470 #define CONFIG_SF_DEFAULT_SPEED 10000000 471 #define CONFIG_SF_DEFAULT_MODE 0 472 #endif 473 474 /* 475 * General PCI 476 * Memory space is mapped 1-1, but I/O space must start from 0. 477 */ 478 #define CONFIG_PCIE1 /* PCIE controller 1 */ 479 #define CONFIG_PCIE2 /* PCIE controller 2 */ 480 #define CONFIG_PCIE3 /* PCIE controller 3 */ 481 #define CONFIG_PCIE4 /* PCIE controller 4 */ 482 #define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ 483 #define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ 484 /* controller 1, direct to uli, tgtid 3, Base address 20000 */ 485 #define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 486 #define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 487 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull 488 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ 489 #define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000 490 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 491 #define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull 492 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ 493 494 /* controller 2, Slot 2, tgtid 2, Base address 201000 */ 495 #define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 496 #define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000 497 #define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull 498 #define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */ 499 #define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000 500 #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 501 #define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull 502 #define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ 503 504 /* controller 3, Slot 1, tgtid 1, Base address 202000 */ 505 #define CONFIG_SYS_PCIE3_MEM_VIRT 0xb0000000 506 #define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000 507 #define CONFIG_SYS_PCIE3_MEM_PHYS 0xc30000000ull 508 #define CONFIG_SYS_PCIE3_MEM_SIZE 0x10000000 /* 256M */ 509 #define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000 510 #define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 511 #define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull 512 #define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */ 513 514 /* controller 4, Base address 203000 */ 515 #define CONFIG_SYS_PCIE4_MEM_VIRT 0xc0000000 516 #define CONFIG_SYS_PCIE4_MEM_BUS 0xe0000000 517 #define CONFIG_SYS_PCIE4_MEM_PHYS 0xc40000000ull 518 #define CONFIG_SYS_PCIE4_MEM_SIZE 0x10000000 /* 256M */ 519 #define CONFIG_SYS_PCIE4_IO_BUS 0x00000000 520 #define CONFIG_SYS_PCIE4_IO_PHYS 0xff8030000ull 521 #define CONFIG_SYS_PCIE4_IO_SIZE 0x00010000 /* 64k */ 522 523 #ifdef CONFIG_PCI 524 #define CONFIG_PCI_INDIRECT_BRIDGE 525 #define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata LSZ ADD */ 526 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 527 #endif 528 529 /* Qman/Bman */ 530 #ifndef CONFIG_NOBQFMAN 531 #define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */ 532 #define CONFIG_SYS_BMAN_NUM_PORTALS 18 533 #define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000 534 #define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull 535 #define CONFIG_SYS_BMAN_MEM_SIZE 0x02000000 536 #define CONFIG_SYS_BMAN_SP_CENA_SIZE 0x4000 537 #define CONFIG_SYS_BMAN_SP_CINH_SIZE 0x1000 538 #define CONFIG_SYS_BMAN_CENA_BASE CONFIG_SYS_BMAN_MEM_BASE 539 #define CONFIG_SYS_BMAN_CENA_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) 540 #define CONFIG_SYS_BMAN_CINH_BASE (CONFIG_SYS_BMAN_MEM_BASE + \ 541 CONFIG_SYS_BMAN_CENA_SIZE) 542 #define CONFIG_SYS_BMAN_CINH_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) 543 #define CONFIG_SYS_BMAN_SWP_ISDR_REG 0xE08 544 #define CONFIG_SYS_QMAN_NUM_PORTALS 18 545 #define CONFIG_SYS_QMAN_MEM_BASE 0xf6000000 546 #define CONFIG_SYS_QMAN_MEM_PHYS 0xff6000000ull 547 #define CONFIG_SYS_QMAN_MEM_SIZE 0x02000000 548 #define CONFIG_SYS_QMAN_SP_CENA_SIZE 0x4000 549 #define CONFIG_SYS_QMAN_SP_CINH_SIZE 0x1000 550 #define CONFIG_SYS_QMAN_CENA_BASE CONFIG_SYS_QMAN_MEM_BASE 551 #define CONFIG_SYS_QMAN_CENA_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) 552 #define CONFIG_SYS_QMAN_CINH_BASE (CONFIG_SYS_QMAN_MEM_BASE + \ 553 CONFIG_SYS_QMAN_CENA_SIZE) 554 #define CONFIG_SYS_QMAN_CINH_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) 555 #define CONFIG_SYS_QMAN_SWP_ISDR_REG 0xE08 556 557 #define CONFIG_SYS_DPAA_FMAN 558 #define CONFIG_SYS_DPAA_PME 559 #define CONFIG_SYS_PMAN 560 #define CONFIG_SYS_DPAA_DCE 561 #define CONFIG_SYS_DPAA_RMAN /* RMan */ 562 #define CONFIG_SYS_INTERLAKEN 563 564 /* Default address of microcode for the Linux Fman driver */ 565 #if defined(CONFIG_SPIFLASH) 566 /* 567 * env is stored at 0x100000, sector size is 0x10000, ucode is stored after 568 * env, so we got 0x110000. 569 */ 570 #define CONFIG_SYS_QE_FW_IN_SPIFLASH 571 #define CONFIG_SYS_CORTINA_FW_IN_SPIFLASH 572 #define CONFIG_SYS_FMAN_FW_ADDR 0x110000 573 #define CONFIG_CORTINA_FW_ADDR 0x120000 574 575 #elif defined(CONFIG_SDCARD) 576 /* 577 * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is 578 * about 1MB (2048 blocks), Env is stored after the image, and the env size is 579 * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080. 580 */ 581 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC 582 #define CONFIG_SYS_CORTINA_FW_IN_MMC 583 #define CONFIG_SYS_FMAN_FW_ADDR (512 * 0x820) 584 #define CONFIG_CORTINA_FW_ADDR (512 * 0x8a0) 585 586 #elif defined(CONFIG_NAND) 587 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND 588 #define CONFIG_SYS_CORTINA_FW_IN_NAND 589 #define CONFIG_SYS_FMAN_FW_ADDR (3 * CONFIG_SYS_NAND_BLOCK_SIZE) 590 #define CONFIG_CORTINA_FW_ADDR (4 * CONFIG_SYS_NAND_BLOCK_SIZE) 591 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) 592 /* 593 * Slave has no ucode locally, it can fetch this from remote. When implementing 594 * in two corenet boards, slave's ucode could be stored in master's memory 595 * space, the address can be mapped from slave TLB->slave LAW-> 596 * slave SRIO or PCIE outbound window->master inbound window-> 597 * master LAW->the ucode address in master's memory space. 598 */ 599 #define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE 600 #define CONFIG_SYS_CORTINA_FW_IN_REMOTE 601 #define CONFIG_SYS_FMAN_FW_ADDR 0xFFE00000 602 #define CONFIG_CORTINA_FW_ADDR 0xFFE10000 603 #else 604 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR 605 #define CONFIG_SYS_CORTINA_FW_IN_NOR 606 #define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000 607 #define CONFIG_CORTINA_FW_ADDR 0xEFE00000 608 #endif 609 #define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 610 #define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) 611 #endif /* CONFIG_NOBQFMAN */ 612 613 #ifdef CONFIG_SYS_DPAA_FMAN 614 #define CONFIG_FMAN_ENET 615 #define CONFIG_PHYLIB_10G 616 #define CONFIG_PHY_AQUANTIA 617 #define CONFIG_PHY_CORTINA 618 #define CONFIG_PHY_REALTEK 619 #define CONFIG_CORTINA_FW_LENGTH 0x40000 620 #define RGMII_PHY1_ADDR 0x01 /* RealTek RTL8211E */ 621 #define RGMII_PHY2_ADDR 0x02 622 #define CORTINA_PHY_ADDR1 0x0c /* Cortina CS4315 */ 623 #define CORTINA_PHY_ADDR2 0x0d 624 #define FM1_10GEC3_PHY_ADDR 0x00 /* Aquantia AQ1202 10G Base-T */ 625 #define FM1_10GEC4_PHY_ADDR 0x01 626 #endif 627 628 #ifdef CONFIG_FMAN_ENET 629 #define CONFIG_MII /* MII PHY management */ 630 #define CONFIG_ETHPRIME "FM1@DTSEC3" 631 #define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ 632 #endif 633 634 /* 635 * SATA 636 */ 637 #ifdef CONFIG_FSL_SATA_V2 638 #define CONFIG_LIBATA 639 #define CONFIG_FSL_SATA 640 #define CONFIG_SYS_SATA_MAX_DEVICE 2 641 #define CONFIG_SATA1 642 #define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR 643 #define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA 644 #define CONFIG_SATA2 645 #define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR 646 #define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA 647 #define CONFIG_LBA48 648 #define CONFIG_CMD_SATA 649 #endif 650 651 /* 652 * USB 653 */ 654 #ifdef CONFIG_USB_EHCI_HCD 655 #define CONFIG_USB_EHCI_FSL 656 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET 657 #define CONFIG_HAS_FSL_DR_USB 658 #endif 659 660 /* 661 * SDHC 662 */ 663 #ifdef CONFIG_MMC 664 #define CONFIG_FSL_ESDHC 665 #define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR 666 #define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT 667 #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33 668 #endif 669 670 /* 671 * Dynamic MTD Partition support with mtdparts 672 */ 673 #ifdef CONFIG_MTD_NOR_FLASH 674 #define CONFIG_MTD_DEVICE 675 #define CONFIG_MTD_PARTITIONS 676 #define CONFIG_CMD_MTDPARTS 677 #define CONFIG_FLASH_CFI_MTD 678 #define MTDIDS_DEFAULT "nor0=fe8000000.nor,nand0=fff800000.flash," \ 679 "spi0=spife110000.1" 680 #define MTDPARTS_DEFAULT "mtdparts=fe8000000.nor:1m(uboot),5m(kernel)," \ 681 "128k(dtb),96m(fs),-(user);fff800000.flash:1m(uboot)," \ 682 "5m(kernel),128k(dtb),96m(fs),-(user);spife110000.1:" \ 683 "1m(uboot),5m(kernel),128k(dtb),-(user)" 684 #endif 685 686 /* 687 * Environment 688 */ 689 690 /* 691 * Command line configuration. 692 */ 693 #define CONFIG_CMD_REGINFO 694 695 #ifdef CONFIG_PCI 696 #define CONFIG_CMD_PCI 697 #endif 698 699 /* 700 * Miscellaneous configurable options 701 */ 702 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 703 #define CONFIG_CMDLINE_EDITING /* Command-line editing */ 704 #define CONFIG_AUTO_COMPLETE /* add autocompletion support */ 705 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 706 #ifdef CONFIG_CMD_KGDB 707 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 708 #else 709 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 710 #endif 711 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) 712 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 713 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */ 714 715 /* 716 * For booting Linux, the board info and command line data 717 * have to be in the first 64 MB of memory, since this is 718 * the maximum mapped by the Linux kernel during initialization. 719 */ 720 #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial map for Linux*/ 721 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 722 723 #ifdef CONFIG_CMD_KGDB 724 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ 725 #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ 726 #endif 727 728 /* 729 * Environment Configuration 730 */ 731 #define CONFIG_ROOTPATH "/opt/nfsroot" 732 #define CONFIG_BOOTFILE "uImage" 733 #define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server */ 734 735 /* default location for tftp and bootm */ 736 #define CONFIG_LOADADDR 1000000 737 #define __USB_PHY_TYPE utmi 738 739 #define CONFIG_EXTRA_ENV_SETTINGS \ 740 "hwconfig=fsl_ddr:" \ 741 "ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) "," \ 742 "bank_intlv=auto;" \ 743 "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\ 744 "netdev=eth0\0" \ 745 "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ 746 "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \ 747 "tftpflash=tftpboot $loadaddr $uboot && " \ 748 "protect off $ubootaddr +$filesize && " \ 749 "erase $ubootaddr +$filesize && " \ 750 "cp.b $loadaddr $ubootaddr $filesize && " \ 751 "protect on $ubootaddr +$filesize && " \ 752 "cmp.b $loadaddr $ubootaddr $filesize\0" \ 753 "consoledev=ttyS0\0" \ 754 "ramdiskaddr=2000000\0" \ 755 "ramdiskfile=t2080rdb/ramdisk.uboot\0" \ 756 "fdtaddr=1e00000\0" \ 757 "fdtfile=t2080rdb/t2080rdb.dtb\0" \ 758 "bdev=sda3\0" 759 760 /* 761 * For emulation this causes u-boot to jump to the start of the 762 * proof point app code automatically 763 */ 764 #define CONFIG_PROOF_POINTS \ 765 "setenv bootargs root=/dev/$bdev rw " \ 766 "console=$consoledev,$baudrate $othbootargs;" \ 767 "cpu 1 release 0x29000000 - - -;" \ 768 "cpu 2 release 0x29000000 - - -;" \ 769 "cpu 3 release 0x29000000 - - -;" \ 770 "cpu 4 release 0x29000000 - - -;" \ 771 "cpu 5 release 0x29000000 - - -;" \ 772 "cpu 6 release 0x29000000 - - -;" \ 773 "cpu 7 release 0x29000000 - - -;" \ 774 "go 0x29000000" 775 776 #define CONFIG_HVBOOT \ 777 "setenv bootargs config-addr=0x60000000; " \ 778 "bootm 0x01000000 - 0x00f00000" 779 780 #define CONFIG_ALU \ 781 "setenv bootargs root=/dev/$bdev rw " \ 782 "console=$consoledev,$baudrate $othbootargs;" \ 783 "cpu 1 release 0x01000000 - - -;" \ 784 "cpu 2 release 0x01000000 - - -;" \ 785 "cpu 3 release 0x01000000 - - -;" \ 786 "cpu 4 release 0x01000000 - - -;" \ 787 "cpu 5 release 0x01000000 - - -;" \ 788 "cpu 6 release 0x01000000 - - -;" \ 789 "cpu 7 release 0x01000000 - - -;" \ 790 "go 0x01000000" 791 792 #define CONFIG_LINUX \ 793 "setenv bootargs root=/dev/ram rw " \ 794 "console=$consoledev,$baudrate $othbootargs;" \ 795 "setenv ramdiskaddr 0x02000000;" \ 796 "setenv fdtaddr 0x00c00000;" \ 797 "setenv loadaddr 0x1000000;" \ 798 "bootm $loadaddr $ramdiskaddr $fdtaddr" 799 800 #define CONFIG_HDBOOT \ 801 "setenv bootargs root=/dev/$bdev rw " \ 802 "console=$consoledev,$baudrate $othbootargs;" \ 803 "tftp $loadaddr $bootfile;" \ 804 "tftp $fdtaddr $fdtfile;" \ 805 "bootm $loadaddr - $fdtaddr" 806 807 #define CONFIG_NFSBOOTCOMMAND \ 808 "setenv bootargs root=/dev/nfs rw " \ 809 "nfsroot=$serverip:$rootpath " \ 810 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 811 "console=$consoledev,$baudrate $othbootargs;" \ 812 "tftp $loadaddr $bootfile;" \ 813 "tftp $fdtaddr $fdtfile;" \ 814 "bootm $loadaddr - $fdtaddr" 815 816 #define CONFIG_RAMBOOTCOMMAND \ 817 "setenv bootargs root=/dev/ram rw " \ 818 "console=$consoledev,$baudrate $othbootargs;" \ 819 "tftp $ramdiskaddr $ramdiskfile;" \ 820 "tftp $loadaddr $bootfile;" \ 821 "tftp $fdtaddr $fdtfile;" \ 822 "bootm $loadaddr $ramdiskaddr $fdtaddr" 823 824 #define CONFIG_BOOTCOMMAND CONFIG_LINUX 825 826 #include <asm/fsl_secure_boot.h> 827 828 #endif /* __T2080RDB_H */ 829