1 /* 2 * Copyright 2014 Freescale Semiconductor, Inc. 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 /* 8 * T2080 RDB/PCIe board configuration file 9 */ 10 11 #ifndef __T2080RDB_H 12 #define __T2080RDB_H 13 14 #define CONFIG_SYS_GENERIC_BOARD 15 #define CONFIG_DISPLAY_BOARDINFO 16 #define CONFIG_T2080RDB 17 #define CONFIG_ICS307_REFCLK_HZ 25000000 /* ICS307 ref clk freq */ 18 #define CONFIG_MMC 19 #define CONFIG_USB_EHCI 20 #define CONFIG_FSL_SATA_V2 21 22 /* High Level Configuration Options */ 23 #define CONFIG_PHYS_64BIT 24 #define CONFIG_BOOKE 25 #define CONFIG_E500 /* BOOKE e500 family */ 26 #define CONFIG_E500MC /* BOOKE e500mc family */ 27 #define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */ 28 #define CONFIG_MP /* support multiple processors */ 29 #define CONFIG_ENABLE_36BIT_PHYS 30 31 #ifdef CONFIG_PHYS_64BIT 32 #define CONFIG_ADDR_MAP 1 33 #define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */ 34 #endif 35 36 #define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */ 37 #define CONFIG_SYS_NUM_CPC CONFIG_NUM_DDR_CONTROLLERS 38 #define CONFIG_FSL_IFC /* Enable IFC Support */ 39 #define CONFIG_FSL_CAAM /* Enable SEC/CAAM */ 40 #define CONFIG_FSL_LAW /* Use common FSL init code */ 41 #define CONFIG_ENV_OVERWRITE 42 43 #ifdef CONFIG_RAMBOOT_PBL 44 #define CONFIG_SYS_FSL_PBL_PBI board/freescale/t208xrdb/t2080_pbi.cfg 45 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xrdb/t2080_rcw.cfg 46 47 #define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT 48 #define CONFIG_SPL_ENV_SUPPORT 49 #define CONFIG_SPL_SERIAL_SUPPORT 50 #define CONFIG_SPL_FLUSH_IMAGE 51 #define CONFIG_SPL_TARGET "u-boot-with-spl.bin" 52 #define CONFIG_SPL_LIBGENERIC_SUPPORT 53 #define CONFIG_SPL_LIBCOMMON_SUPPORT 54 #define CONFIG_SPL_I2C_SUPPORT 55 #define CONFIG_SPL_DRIVERS_MISC_SUPPORT 56 #define CONFIG_FSL_LAW /* Use common FSL init code */ 57 #define CONFIG_SYS_TEXT_BASE 0x00201000 58 #define CONFIG_SPL_TEXT_BASE 0xFFFD8000 59 #define CONFIG_SPL_PAD_TO 0x40000 60 #define CONFIG_SPL_MAX_SIZE 0x28000 61 #define RESET_VECTOR_OFFSET 0x27FFC 62 #define BOOT_PAGE_OFFSET 0x27000 63 #ifdef CONFIG_SPL_BUILD 64 #define CONFIG_SPL_SKIP_RELOCATE 65 #define CONFIG_SPL_COMMON_INIT_DDR 66 #define CONFIG_SYS_CCSR_DO_NOT_RELOCATE 67 #define CONFIG_SYS_NO_FLASH 68 #endif 69 70 #ifdef CONFIG_NAND 71 #define CONFIG_SPL_NAND_SUPPORT 72 #define CONFIG_SYS_NAND_U_BOOT_SIZE (768 << 10) 73 #define CONFIG_SYS_NAND_U_BOOT_DST 0x00200000 74 #define CONFIG_SYS_NAND_U_BOOT_START 0x00200000 75 #define CONFIG_SYS_NAND_U_BOOT_OFFS (256 << 10) 76 #define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot-nand.lds" 77 #define CONFIG_SPL_NAND_BOOT 78 #endif 79 80 #ifdef CONFIG_SPIFLASH 81 #define CONFIG_RESET_VECTOR_ADDRESS 0x200FFC 82 #define CONFIG_SPL_SPI_SUPPORT 83 #define CONFIG_SPL_SPI_FLASH_SUPPORT 84 #define CONFIG_SPL_SPI_FLASH_MINIMAL 85 #define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE (768 << 10) 86 #define CONFIG_SYS_SPI_FLASH_U_BOOT_DST (0x00200000) 87 #define CONFIG_SYS_SPI_FLASH_U_BOOT_START (0x00200000) 88 #define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS (256 << 10) 89 #define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot.lds" 90 #ifndef CONFIG_SPL_BUILD 91 #define CONFIG_SYS_MPC85XX_NO_RESETVEC 92 #endif 93 #define CONFIG_SPL_SPI_BOOT 94 #endif 95 96 #ifdef CONFIG_SDCARD 97 #define CONFIG_RESET_VECTOR_ADDRESS 0x200FFC 98 #define CONFIG_SPL_MMC_SUPPORT 99 #define CONFIG_SPL_MMC_MINIMAL 100 #define CONFIG_SYS_MMC_U_BOOT_SIZE (768 << 10) 101 #define CONFIG_SYS_MMC_U_BOOT_DST (0x00200000) 102 #define CONFIG_SYS_MMC_U_BOOT_START (0x00200000) 103 #define CONFIG_SYS_MMC_U_BOOT_OFFS (260 << 10) 104 #define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot.lds" 105 #ifndef CONFIG_SPL_BUILD 106 #define CONFIG_SYS_MPC85XX_NO_RESETVEC 107 #endif 108 #define CONFIG_SPL_MMC_BOOT 109 #endif 110 111 #endif /* CONFIG_RAMBOOT_PBL */ 112 113 #define CONFIG_SRIO_PCIE_BOOT_MASTER 114 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE 115 /* Set 1M boot space */ 116 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000) 117 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \ 118 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR) 119 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc 120 #define CONFIG_SYS_NO_FLASH 121 #endif 122 123 #ifndef CONFIG_SYS_TEXT_BASE 124 #define CONFIG_SYS_TEXT_BASE 0xeff40000 125 #endif 126 127 #ifndef CONFIG_RESET_VECTOR_ADDRESS 128 #define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc 129 #endif 130 131 /* 132 * These can be toggled for performance analysis, otherwise use default. 133 */ 134 #define CONFIG_SYS_CACHE_STASHING 135 #define CONFIG_BTB /* toggle branch predition */ 136 #define CONFIG_DDR_ECC 137 #ifdef CONFIG_DDR_ECC 138 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER 139 #define CONFIG_MEM_INIT_VALUE 0xdeadbeef 140 #endif 141 142 #define CONFIG_CMD_MEMTEST 143 #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ 144 #define CONFIG_SYS_MEMTEST_END 0x00400000 145 #define CONFIG_SYS_ALT_MEMTEST 146 147 #ifndef CONFIG_SYS_NO_FLASH 148 #define CONFIG_FLASH_CFI_DRIVER 149 #define CONFIG_SYS_FLASH_CFI 150 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 151 #endif 152 153 #if defined(CONFIG_SPIFLASH) 154 #define CONFIG_SYS_EXTRA_ENV_RELOC 155 #define CONFIG_ENV_IS_IN_SPI_FLASH 156 #define CONFIG_ENV_SPI_BUS 0 157 #define CONFIG_ENV_SPI_CS 0 158 #define CONFIG_ENV_SPI_MAX_HZ 10000000 159 #define CONFIG_ENV_SPI_MODE 0 160 #define CONFIG_ENV_SIZE 0x2000 /* 8KB */ 161 #define CONFIG_ENV_OFFSET 0x100000 /* 1MB */ 162 #define CONFIG_ENV_SECT_SIZE 0x10000 163 #elif defined(CONFIG_SDCARD) 164 #define CONFIG_SYS_EXTRA_ENV_RELOC 165 #define CONFIG_ENV_IS_IN_MMC 166 #define CONFIG_SYS_MMC_ENV_DEV 0 167 #define CONFIG_ENV_SIZE 0x2000 168 #define CONFIG_ENV_OFFSET (512 * 0x800) 169 #elif defined(CONFIG_NAND) 170 #define CONFIG_SYS_EXTRA_ENV_RELOC 171 #define CONFIG_ENV_IS_IN_NAND 172 #define CONFIG_ENV_SIZE 0x2000 173 #define CONFIG_ENV_OFFSET (2 * CONFIG_SYS_NAND_BLOCK_SIZE) 174 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) 175 #define CONFIG_ENV_IS_IN_REMOTE 176 #define CONFIG_ENV_ADDR 0xffe20000 177 #define CONFIG_ENV_SIZE 0x2000 178 #elif defined(CONFIG_ENV_IS_NOWHERE) 179 #define CONFIG_ENV_SIZE 0x2000 180 #else 181 #define CONFIG_ENV_IS_IN_FLASH 182 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) 183 #define CONFIG_ENV_SIZE 0x2000 184 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ 185 #endif 186 187 #ifndef __ASSEMBLY__ 188 unsigned long get_board_sys_clk(void); 189 unsigned long get_board_ddr_clk(void); 190 #endif 191 192 #define CONFIG_SYS_CLK_FREQ 66660000 193 #define CONFIG_DDR_CLK_FREQ 133330000 194 195 /* 196 * Config the L3 Cache as L3 SRAM 197 */ 198 #define CONFIG_SYS_INIT_L3_ADDR 0xFFFC0000 199 #define CONFIG_SYS_L3_SIZE (512 << 10) 200 #define CONFIG_SPL_GD_ADDR (CONFIG_SYS_INIT_L3_ADDR + 32 * 1024) 201 #ifdef CONFIG_RAMBOOT_PBL 202 #define CONFIG_ENV_ADDR (CONFIG_SPL_GD_ADDR + 4 * 1024) 203 #endif 204 #define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SPL_GD_ADDR + 12 * 1024) 205 #define CONFIG_SPL_RELOC_MALLOC_SIZE (50 << 10) 206 #define CONFIG_SPL_RELOC_STACK (CONFIG_SPL_GD_ADDR + 64 * 1024) 207 #define CONFIG_SPL_RELOC_STACK_SIZE (22 << 10) 208 209 #define CONFIG_SYS_DCSRBAR 0xf0000000 210 #define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull 211 212 /* EEPROM */ 213 #define CONFIG_ID_EEPROM 214 #define CONFIG_SYS_I2C_EEPROM_NXID 215 #define CONFIG_SYS_EEPROM_BUS_NUM 0 216 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 217 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 218 219 /* 220 * DDR Setup 221 */ 222 #define CONFIG_VERY_BIG_RAM 223 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 224 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 225 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 226 #define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR) 227 #define CONFIG_DDR_SPD 228 #define CONFIG_SYS_FSL_DDR3 229 #undef CONFIG_FSL_DDR_INTERACTIVE 230 #define CONFIG_SYS_SPD_BUS_NUM 0 231 #define CONFIG_SYS_SDRAM_SIZE 2048 /* for fixed parameter use */ 232 #define SPD_EEPROM_ADDRESS1 0x51 233 #define SPD_EEPROM_ADDRESS2 0x52 234 #define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1 235 #define CTRL_INTLV_PREFERED cacheline 236 237 /* 238 * IFC Definitions 239 */ 240 #define CONFIG_SYS_FLASH_BASE 0xe8000000 241 #define CONFIG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CONFIG_SYS_FLASH_BASE) 242 #define CONFIG_SYS_NOR0_CSPR_EXT (0xf) 243 #define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \ 244 CSPR_PORT_SIZE_16 | \ 245 CSPR_MSEL_NOR | \ 246 CSPR_V) 247 #define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024) 248 249 /* NOR Flash Timing Params */ 250 #define CONFIG_SYS_NOR_CSOR CSOR_NAND_TRHZ_80 251 252 #define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \ 253 FTIM0_NOR_TEADC(0x5) | \ 254 FTIM0_NOR_TEAHC(0x5)) 255 #define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \ 256 FTIM1_NOR_TRAD_NOR(0x1A) |\ 257 FTIM1_NOR_TSEQRAD_NOR(0x13)) 258 #define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \ 259 FTIM2_NOR_TCH(0x4) | \ 260 FTIM2_NOR_TWPH(0x0E) | \ 261 FTIM2_NOR_TWP(0x1c)) 262 #define CONFIG_SYS_NOR_FTIM3 0x0 263 264 #define CONFIG_SYS_FLASH_QUIET_TEST 265 #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ 266 267 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 268 #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ 269 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 270 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 271 #define CONFIG_SYS_FLASH_EMPTY_INFO 272 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS } 273 274 /* CPLD on IFC */ 275 #define CONFIG_SYS_CPLD_BASE 0xffdf0000 276 #define CONFIG_SYS_CPLD_BASE_PHYS (0xf00000000ull | CONFIG_SYS_CPLD_BASE) 277 #define CONFIG_SYS_CSPR2_EXT (0xf) 278 #define CONFIG_SYS_CSPR2 (CSPR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE) \ 279 | CSPR_PORT_SIZE_8 \ 280 | CSPR_MSEL_GPCM \ 281 | CSPR_V) 282 #define CONFIG_SYS_AMASK2 IFC_AMASK(64*1024) 283 #define CONFIG_SYS_CSOR2 0x0 284 285 /* CPLD Timing parameters for IFC CS2 */ 286 #define CONFIG_SYS_CS2_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \ 287 FTIM0_GPCM_TEADC(0x0e) | \ 288 FTIM0_GPCM_TEAHC(0x0e)) 289 #define CONFIG_SYS_CS2_FTIM1 (FTIM1_GPCM_TACO(0x0e) | \ 290 FTIM1_GPCM_TRAD(0x1f)) 291 #define CONFIG_SYS_CS2_FTIM2 (FTIM2_GPCM_TCS(0x0e) | \ 292 FTIM2_GPCM_TCH(0x8) | \ 293 FTIM2_GPCM_TWP(0x1f)) 294 #define CONFIG_SYS_CS2_FTIM3 0x0 295 296 /* NAND Flash on IFC */ 297 #define CONFIG_NAND_FSL_IFC 298 #define CONFIG_SYS_NAND_BASE 0xff800000 299 #define CONFIG_SYS_NAND_BASE_PHYS (0xf00000000ull | CONFIG_SYS_NAND_BASE) 300 301 #define CONFIG_SYS_NAND_CSPR_EXT (0xf) 302 #define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ 303 | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \ 304 | CSPR_MSEL_NAND /* MSEL = NAND */ \ 305 | CSPR_V) 306 #define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024) 307 308 #define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \ 309 | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \ 310 | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \ 311 | CSOR_NAND_RAL_3 /* RAL = 2Byes */ \ 312 | CSOR_NAND_PGS_2K /* Page Size = 2K */\ 313 | CSOR_NAND_SPRZ_64 /* Spare size = 64 */\ 314 | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/ 315 316 #define CONFIG_SYS_NAND_ONFI_DETECTION 317 318 /* ONFI NAND Flash mode0 Timing Params */ 319 #define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \ 320 FTIM0_NAND_TWP(0x18) | \ 321 FTIM0_NAND_TWCHT(0x07) | \ 322 FTIM0_NAND_TWH(0x0a)) 323 #define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \ 324 FTIM1_NAND_TWBE(0x39) | \ 325 FTIM1_NAND_TRR(0x0e) | \ 326 FTIM1_NAND_TRP(0x18)) 327 #define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \ 328 FTIM2_NAND_TREH(0x0a) | \ 329 FTIM2_NAND_TWHRE(0x1e)) 330 #define CONFIG_SYS_NAND_FTIM3 0x0 331 332 #define CONFIG_SYS_NAND_DDR_LAW 11 333 #define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } 334 #define CONFIG_SYS_MAX_NAND_DEVICE 1 335 #define CONFIG_CMD_NAND 336 #define CONFIG_SYS_NAND_BLOCK_SIZE (512 * 1024) 337 338 #if defined(CONFIG_NAND) 339 #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT 340 #define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR 341 #define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK 342 #define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR 343 #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0 344 #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1 345 #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2 346 #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3 347 #define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR0_CSPR_EXT 348 #define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR0_CSPR 349 #define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK 350 #define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR 351 #define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0 352 #define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1 353 #define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2 354 #define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3 355 #else 356 #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT 357 #define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR 358 #define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK 359 #define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR 360 #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0 361 #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1 362 #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2 363 #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3 364 #define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NAND_CSPR_EXT 365 #define CONFIG_SYS_CSPR1 CONFIG_SYS_NAND_CSPR 366 #define CONFIG_SYS_AMASK1 CONFIG_SYS_NAND_AMASK 367 #define CONFIG_SYS_CSOR1 CONFIG_SYS_NAND_CSOR 368 #define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NAND_FTIM0 369 #define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NAND_FTIM1 370 #define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NAND_FTIM2 371 #define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NAND_FTIM3 372 #endif 373 374 #if defined(CONFIG_RAMBOOT_PBL) 375 #define CONFIG_SYS_RAMBOOT 376 #endif 377 378 #ifdef CONFIG_SPL_BUILD 379 #define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE 380 #else 381 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 382 #endif 383 384 #define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */ 385 #define CONFIG_MISC_INIT_R 386 #define CONFIG_HWCONFIG 387 388 /* define to use L1 as initial stack */ 389 #define CONFIG_L1_INIT_RAM 390 #define CONFIG_SYS_INIT_RAM_LOCK 391 #define CONFIG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */ 392 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf 393 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW 0xfe0ec000 394 /* The assembler doesn't like typecast */ 395 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \ 396 ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \ 397 CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW) 398 #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 399 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ 400 GENERATED_GBL_DATA_SIZE) 401 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 402 #define CONFIG_SYS_MONITOR_LEN (768 * 1024) 403 #define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024) 404 405 /* 406 * Serial Port 407 */ 408 #define CONFIG_CONS_INDEX 1 409 #define CONFIG_SYS_NS16550 410 #define CONFIG_SYS_NS16550_SERIAL 411 #define CONFIG_SYS_NS16550_REG_SIZE 1 412 #define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2) 413 #define CONFIG_SYS_BAUDRATE_TABLE \ 414 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} 415 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500) 416 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600) 417 #define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500) 418 #define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600) 419 420 /* Use the HUSH parser */ 421 #define CONFIG_SYS_HUSH_PARSER 422 #define CONFIG_SYS_PROMPT_HUSH_PS2 "> " 423 424 /* pass open firmware flat tree */ 425 #define CONFIG_OF_LIBFDT 426 #define CONFIG_OF_BOARD_SETUP 427 #define CONFIG_OF_STDOUT_VIA_ALIAS 428 429 /* new uImage format support */ 430 #define CONFIG_FIT 431 #define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ 432 433 /* 434 * I2C 435 */ 436 #define CONFIG_SYS_I2C 437 #define CONFIG_SYS_I2C_FSL 438 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 439 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F 440 #define CONFIG_SYS_FSL_I2C3_SLAVE 0x7F 441 #define CONFIG_SYS_FSL_I2C4_SLAVE 0x7F 442 #define CONFIG_SYS_FSL_I2C_OFFSET 0x118000 443 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100 444 #define CONFIG_SYS_FSL_I2C3_OFFSET 0x119000 445 #define CONFIG_SYS_FSL_I2C4_OFFSET 0x119100 446 #define CONFIG_SYS_FSL_I2C_SPEED 100000 447 #define CONFIG_SYS_FSL_I2C2_SPEED 100000 448 #define CONFIG_SYS_FSL_I2C3_SPEED 100000 449 #define CONFIG_SYS_FSL_I2C4_SPEED 100000 450 #define I2C_MUX_PCA_ADDR_PRI 0x77 /* I2C bus multiplexer,primary */ 451 #define I2C_MUX_PCA_ADDR_SEC1 0x75 /* I2C bus multiplexer,secondary 1 */ 452 #define I2C_MUX_PCA_ADDR_SEC2 0x76 /* I2C bus multiplexer,secondary 2 */ 453 #define I2C_MUX_CH_DEFAULT 0x8 454 455 #define I2C_MUX_CH_VOL_MONITOR 0xa 456 457 #define CONFIG_VID_FLS_ENV "t208xrdb_vdd_mv" 458 #ifndef CONFIG_SPL_BUILD 459 #define CONFIG_VID 460 #endif 461 #define CONFIG_VOL_MONITOR_IR36021_SET 462 #define CONFIG_VOL_MONITOR_IR36021_READ 463 /* The lowest and highest voltage allowed for T208xRDB */ 464 #define VDD_MV_MIN 819 465 #define VDD_MV_MAX 1212 466 467 /* 468 * RapidIO 469 */ 470 #define CONFIG_SYS_SRIO1_MEM_VIRT 0xa0000000 471 #define CONFIG_SYS_SRIO1_MEM_PHYS 0xc20000000ull 472 #define CONFIG_SYS_SRIO1_MEM_SIZE 0x10000000 /* 256M */ 473 #define CONFIG_SYS_SRIO2_MEM_VIRT 0xb0000000 474 #define CONFIG_SYS_SRIO2_MEM_PHYS 0xc30000000ull 475 #define CONFIG_SYS_SRIO2_MEM_SIZE 0x10000000 /* 256M */ 476 /* 477 * for slave u-boot IMAGE instored in master memory space, 478 * PHYS must be aligned based on the SIZE 479 */ 480 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull 481 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull 482 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x100000 /* 1M */ 483 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull 484 /* 485 * for slave UCODE and ENV instored in master memory space, 486 * PHYS must be aligned based on the SIZE 487 */ 488 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull 489 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull 490 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */ 491 492 /* slave core release by master*/ 493 #define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4 494 #define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */ 495 496 /* 497 * SRIO_PCIE_BOOT - SLAVE 498 */ 499 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE 500 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000 501 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \ 502 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR) 503 #endif 504 505 /* 506 * eSPI - Enhanced SPI 507 */ 508 #ifdef CONFIG_SPI_FLASH 509 #define CONFIG_FSL_ESPI 510 #define CONFIG_SPI_FLASH_STMICRO 511 #define CONFIG_SPI_FLASH_BAR 512 #define CONFIG_CMD_SF 513 #define CONFIG_SF_DEFAULT_SPEED 10000000 514 #define CONFIG_SF_DEFAULT_MODE 0 515 #endif 516 517 /* 518 * General PCI 519 * Memory space is mapped 1-1, but I/O space must start from 0. 520 */ 521 #define CONFIG_PCI /* Enable PCI/PCIE */ 522 #define CONFIG_PCIE1 /* PCIE controler 1 */ 523 #define CONFIG_PCIE2 /* PCIE controler 2 */ 524 #define CONFIG_PCIE3 /* PCIE controler 3 */ 525 #define CONFIG_PCIE4 /* PCIE controler 4 */ 526 #define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ 527 #define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ 528 /* controller 1, direct to uli, tgtid 3, Base address 20000 */ 529 #define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 530 #define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 531 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull 532 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ 533 #define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000 534 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 535 #define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull 536 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ 537 538 /* controller 2, Slot 2, tgtid 2, Base address 201000 */ 539 #define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 540 #define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000 541 #define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull 542 #define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */ 543 #define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000 544 #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 545 #define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull 546 #define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ 547 548 /* controller 3, Slot 1, tgtid 1, Base address 202000 */ 549 #define CONFIG_SYS_PCIE3_MEM_VIRT 0xb0000000 550 #define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000 551 #define CONFIG_SYS_PCIE3_MEM_PHYS 0xc30000000ull 552 #define CONFIG_SYS_PCIE3_MEM_SIZE 0x10000000 /* 256M */ 553 #define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000 554 #define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 555 #define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull 556 #define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */ 557 558 /* controller 4, Base address 203000 */ 559 #define CONFIG_SYS_PCIE4_MEM_VIRT 0xc0000000 560 #define CONFIG_SYS_PCIE4_MEM_BUS 0xe0000000 561 #define CONFIG_SYS_PCIE4_MEM_PHYS 0xc40000000ull 562 #define CONFIG_SYS_PCIE4_MEM_SIZE 0x10000000 /* 256M */ 563 #define CONFIG_SYS_PCIE4_IO_BUS 0x00000000 564 #define CONFIG_SYS_PCIE4_IO_PHYS 0xff8030000ull 565 #define CONFIG_SYS_PCIE4_IO_SIZE 0x00010000 /* 64k */ 566 567 #ifdef CONFIG_PCI 568 #define CONFIG_PCI_INDIRECT_BRIDGE 569 #define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata LSZ ADD */ 570 #define CONFIG_PCI_PNP /* do pci plug-and-play */ 571 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 572 #define CONFIG_DOS_PARTITION 573 #endif 574 575 /* Qman/Bman */ 576 #ifndef CONFIG_NOBQFMAN 577 #define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */ 578 #define CONFIG_SYS_BMAN_NUM_PORTALS 18 579 #define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000 580 #define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull 581 #define CONFIG_SYS_BMAN_MEM_SIZE 0x02000000 582 #define CONFIG_SYS_BMAN_SP_CENA_SIZE 0x4000 583 #define CONFIG_SYS_BMAN_SP_CINH_SIZE 0x1000 584 #define CONFIG_SYS_BMAN_CENA_BASE CONFIG_SYS_BMAN_MEM_BASE 585 #define CONFIG_SYS_BMAN_CENA_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) 586 #define CONFIG_SYS_BMAN_CINH_BASE (CONFIG_SYS_BMAN_MEM_BASE + \ 587 CONFIG_SYS_BMAN_CENA_SIZE) 588 #define CONFIG_SYS_BMAN_CINH_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) 589 #define CONFIG_SYS_BMAN_SWP_ISDR_REG 0xE08 590 #define CONFIG_SYS_QMAN_NUM_PORTALS 18 591 #define CONFIG_SYS_QMAN_MEM_BASE 0xf6000000 592 #define CONFIG_SYS_QMAN_MEM_PHYS 0xff6000000ull 593 #define CONFIG_SYS_QMAN_MEM_SIZE 0x02000000 594 #define CONFIG_SYS_QMAN_SP_CENA_SIZE 0x4000 595 #define CONFIG_SYS_QMAN_SP_CINH_SIZE 0x1000 596 #define CONFIG_SYS_QMAN_CENA_BASE CONFIG_SYS_QMAN_MEM_BASE 597 #define CONFIG_SYS_QMAN_CENA_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) 598 #define CONFIG_SYS_QMAN_CINH_BASE (CONFIG_SYS_QMAN_MEM_BASE + \ 599 CONFIG_SYS_QMAN_CENA_SIZE) 600 #define CONFIG_SYS_QMAN_CINH_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) 601 #define CONFIG_SYS_QMAN_SWP_ISDR_REG 0xE08 602 603 #define CONFIG_SYS_DPAA_FMAN 604 #define CONFIG_SYS_DPAA_PME 605 #define CONFIG_SYS_PMAN 606 #define CONFIG_SYS_DPAA_DCE 607 #define CONFIG_SYS_DPAA_RMAN /* RMan */ 608 #define CONFIG_SYS_INTERLAKEN 609 610 /* Default address of microcode for the Linux Fman driver */ 611 #if defined(CONFIG_SPIFLASH) 612 /* 613 * env is stored at 0x100000, sector size is 0x10000, ucode is stored after 614 * env, so we got 0x110000. 615 */ 616 #define CONFIG_SYS_QE_FW_IN_SPIFLASH 617 #define CONFIG_SYS_CORTINA_FW_IN_SPIFLASH 618 #define CONFIG_SYS_FMAN_FW_ADDR 0x110000 619 #define CONFIG_CORTINA_FW_ADDR 0x120000 620 621 #elif defined(CONFIG_SDCARD) 622 /* 623 * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is 624 * about 1MB (2048 blocks), Env is stored after the image, and the env size is 625 * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080. 626 */ 627 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC 628 #define CONFIG_SYS_CORTINA_FW_IN_MMC 629 #define CONFIG_SYS_FMAN_FW_ADDR (512 * 0x820) 630 #define CONFIG_CORTINA_FW_ADDR (512 * 0x8a0) 631 632 #elif defined(CONFIG_NAND) 633 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND 634 #define CONFIG_SYS_CORTINA_FW_IN_NAND 635 #define CONFIG_SYS_FMAN_FW_ADDR (3 * CONFIG_SYS_NAND_BLOCK_SIZE) 636 #define CONFIG_CORTINA_FW_ADDR (4 * CONFIG_SYS_NAND_BLOCK_SIZE) 637 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) 638 /* 639 * Slave has no ucode locally, it can fetch this from remote. When implementing 640 * in two corenet boards, slave's ucode could be stored in master's memory 641 * space, the address can be mapped from slave TLB->slave LAW-> 642 * slave SRIO or PCIE outbound window->master inbound window-> 643 * master LAW->the ucode address in master's memory space. 644 */ 645 #define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE 646 #define CONFIG_SYS_CORTINA_FW_IN_REMOTE 647 #define CONFIG_SYS_FMAN_FW_ADDR 0xFFE00000 648 #define CONFIG_CORTINA_FW_ADDR 0xFFE10000 649 #else 650 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR 651 #define CONFIG_SYS_CORTINA_FW_IN_NOR 652 #define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000 653 #define CONFIG_CORTINA_FW_ADDR 0xEFE00000 654 #endif 655 #define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 656 #define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) 657 #endif /* CONFIG_NOBQFMAN */ 658 659 #ifdef CONFIG_SYS_DPAA_FMAN 660 #define CONFIG_FMAN_ENET 661 #define CONFIG_PHYLIB_10G 662 #define CONFIG_PHY_AQUANTIA 663 #define CONFIG_PHY_CORTINA 664 #define CONFIG_PHY_REALTEK 665 #define CONFIG_CORTINA_FW_LENGTH 0x40000 666 #define RGMII_PHY1_ADDR 0x01 /* RealTek RTL8211E */ 667 #define RGMII_PHY2_ADDR 0x02 668 #define CORTINA_PHY_ADDR1 0x0c /* Cortina CS4315 */ 669 #define CORTINA_PHY_ADDR2 0x0d 670 #define FM1_10GEC3_PHY_ADDR 0x00 /* Aquantia AQ1202 10G Base-T */ 671 #define FM1_10GEC4_PHY_ADDR 0x01 672 #endif 673 674 675 #ifdef CONFIG_FMAN_ENET 676 #define CONFIG_MII /* MII PHY management */ 677 #define CONFIG_ETHPRIME "FM1@DTSEC3" 678 #define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ 679 #endif 680 681 /* 682 * SATA 683 */ 684 #ifdef CONFIG_FSL_SATA_V2 685 #define CONFIG_LIBATA 686 #define CONFIG_FSL_SATA 687 #define CONFIG_SYS_SATA_MAX_DEVICE 2 688 #define CONFIG_SATA1 689 #define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR 690 #define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA 691 #define CONFIG_SATA2 692 #define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR 693 #define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA 694 #define CONFIG_LBA48 695 #define CONFIG_CMD_SATA 696 #define CONFIG_DOS_PARTITION 697 #define CONFIG_CMD_EXT2 698 #endif 699 700 /* 701 * USB 702 */ 703 #ifdef CONFIG_USB_EHCI 704 #define CONFIG_CMD_USB 705 #define CONFIG_USB_STORAGE 706 #define CONFIG_USB_EHCI_FSL 707 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET 708 #define CONFIG_CMD_EXT2 709 #define CONFIG_HAS_FSL_DR_USB 710 #endif 711 712 /* 713 * SDHC 714 */ 715 #ifdef CONFIG_MMC 716 #define CONFIG_CMD_MMC 717 #define CONFIG_FSL_ESDHC 718 #define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR 719 #define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT 720 #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33 721 #define CONFIG_GENERIC_MMC 722 #define CONFIG_CMD_EXT2 723 #define CONFIG_CMD_FAT 724 #define CONFIG_DOS_PARTITION 725 #endif 726 727 /* 728 * Dynamic MTD Partition support with mtdparts 729 */ 730 #ifndef CONFIG_SYS_NO_FLASH 731 #define CONFIG_MTD_DEVICE 732 #define CONFIG_MTD_PARTITIONS 733 #define CONFIG_CMD_MTDPARTS 734 #define CONFIG_FLASH_CFI_MTD 735 #define MTDIDS_DEFAULT "nor0=fe8000000.nor,nand0=fff800000.flash," \ 736 "spi0=spife110000.1" 737 #define MTDPARTS_DEFAULT "mtdparts=fe8000000.nor:1m(uboot),5m(kernel)," \ 738 "128k(dtb),96m(fs),-(user);fff800000.flash:1m(uboot)," \ 739 "5m(kernel),128k(dtb),96m(fs),-(user);spife110000.1:" \ 740 "1m(uboot),5m(kernel),128k(dtb),-(user)" 741 #endif 742 743 /* 744 * Environment 745 */ 746 747 /* 748 * Command line configuration. 749 */ 750 #define CONFIG_CMD_DHCP 751 #define CONFIG_CMD_ELF 752 #define CONFIG_CMD_ERRATA 753 #define CONFIG_CMD_MII 754 #define CONFIG_CMD_I2C 755 #define CONFIG_CMD_PING 756 #define CONFIG_CMD_REGINFO 757 758 #ifdef CONFIG_PCI 759 #define CONFIG_CMD_PCI 760 #endif 761 762 /* Hash command with SHA acceleration supported in hardware */ 763 #ifdef CONFIG_FSL_CAAM 764 #define CONFIG_CMD_HASH 765 #define CONFIG_SHA_HW_ACCEL 766 #endif 767 768 /* 769 * Miscellaneous configurable options 770 */ 771 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 772 #define CONFIG_CMDLINE_EDITING /* Command-line editing */ 773 #define CONFIG_AUTO_COMPLETE /* add autocompletion support */ 774 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 775 #ifdef CONFIG_CMD_KGDB 776 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 777 #else 778 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 779 #endif 780 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) 781 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 782 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */ 783 784 /* 785 * For booting Linux, the board info and command line data 786 * have to be in the first 64 MB of memory, since this is 787 * the maximum mapped by the Linux kernel during initialization. 788 */ 789 #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial map for Linux*/ 790 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 791 792 #ifdef CONFIG_CMD_KGDB 793 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ 794 #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ 795 #endif 796 797 /* 798 * Environment Configuration 799 */ 800 #define CONFIG_ROOTPATH "/opt/nfsroot" 801 #define CONFIG_BOOTFILE "uImage" 802 #define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server */ 803 804 /* default location for tftp and bootm */ 805 #define CONFIG_LOADADDR 1000000 806 #define CONFIG_BAUDRATE 115200 807 #define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ 808 #define __USB_PHY_TYPE utmi 809 810 #define CONFIG_EXTRA_ENV_SETTINGS \ 811 "hwconfig=fsl_ddr:" \ 812 "ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) "," \ 813 "bank_intlv=auto;" \ 814 "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\ 815 "netdev=eth0\0" \ 816 "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ 817 "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \ 818 "tftpflash=tftpboot $loadaddr $uboot && " \ 819 "protect off $ubootaddr +$filesize && " \ 820 "erase $ubootaddr +$filesize && " \ 821 "cp.b $loadaddr $ubootaddr $filesize && " \ 822 "protect on $ubootaddr +$filesize && " \ 823 "cmp.b $loadaddr $ubootaddr $filesize\0" \ 824 "consoledev=ttyS0\0" \ 825 "ramdiskaddr=2000000\0" \ 826 "ramdiskfile=t2080rdb/ramdisk.uboot\0" \ 827 "fdtaddr=c00000\0" \ 828 "fdtfile=t2080rdb/t2080rdb.dtb\0" \ 829 "bdev=sda3\0" 830 831 /* 832 * For emulation this causes u-boot to jump to the start of the 833 * proof point app code automatically 834 */ 835 #define CONFIG_PROOF_POINTS \ 836 "setenv bootargs root=/dev/$bdev rw " \ 837 "console=$consoledev,$baudrate $othbootargs;" \ 838 "cpu 1 release 0x29000000 - - -;" \ 839 "cpu 2 release 0x29000000 - - -;" \ 840 "cpu 3 release 0x29000000 - - -;" \ 841 "cpu 4 release 0x29000000 - - -;" \ 842 "cpu 5 release 0x29000000 - - -;" \ 843 "cpu 6 release 0x29000000 - - -;" \ 844 "cpu 7 release 0x29000000 - - -;" \ 845 "go 0x29000000" 846 847 #define CONFIG_HVBOOT \ 848 "setenv bootargs config-addr=0x60000000; " \ 849 "bootm 0x01000000 - 0x00f00000" 850 851 #define CONFIG_ALU \ 852 "setenv bootargs root=/dev/$bdev rw " \ 853 "console=$consoledev,$baudrate $othbootargs;" \ 854 "cpu 1 release 0x01000000 - - -;" \ 855 "cpu 2 release 0x01000000 - - -;" \ 856 "cpu 3 release 0x01000000 - - -;" \ 857 "cpu 4 release 0x01000000 - - -;" \ 858 "cpu 5 release 0x01000000 - - -;" \ 859 "cpu 6 release 0x01000000 - - -;" \ 860 "cpu 7 release 0x01000000 - - -;" \ 861 "go 0x01000000" 862 863 #define CONFIG_LINUX \ 864 "setenv bootargs root=/dev/ram rw " \ 865 "console=$consoledev,$baudrate $othbootargs;" \ 866 "setenv ramdiskaddr 0x02000000;" \ 867 "setenv fdtaddr 0x00c00000;" \ 868 "setenv loadaddr 0x1000000;" \ 869 "bootm $loadaddr $ramdiskaddr $fdtaddr" 870 871 #define CONFIG_HDBOOT \ 872 "setenv bootargs root=/dev/$bdev rw " \ 873 "console=$consoledev,$baudrate $othbootargs;" \ 874 "tftp $loadaddr $bootfile;" \ 875 "tftp $fdtaddr $fdtfile;" \ 876 "bootm $loadaddr - $fdtaddr" 877 878 #define CONFIG_NFSBOOTCOMMAND \ 879 "setenv bootargs root=/dev/nfs rw " \ 880 "nfsroot=$serverip:$rootpath " \ 881 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 882 "console=$consoledev,$baudrate $othbootargs;" \ 883 "tftp $loadaddr $bootfile;" \ 884 "tftp $fdtaddr $fdtfile;" \ 885 "bootm $loadaddr - $fdtaddr" 886 887 #define CONFIG_RAMBOOTCOMMAND \ 888 "setenv bootargs root=/dev/ram rw " \ 889 "console=$consoledev,$baudrate $othbootargs;" \ 890 "tftp $ramdiskaddr $ramdiskfile;" \ 891 "tftp $loadaddr $bootfile;" \ 892 "tftp $fdtaddr $fdtfile;" \ 893 "bootm $loadaddr $ramdiskaddr $fdtaddr" 894 895 #define CONFIG_BOOTCOMMAND CONFIG_LINUX 896 897 #ifdef CONFIG_SECURE_BOOT 898 #include <asm/fsl_secure_boot.h> 899 #define CONFIG_CMD_BLOB 900 #undef CONFIG_CMD_USB 901 #endif 902 903 #endif /* __T2080RDB_H */ 904