1 /* 2 * Copyright 2014 Freescale Semiconductor, Inc. 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 /* 8 * T2080 RDB/PCIe board configuration file 9 */ 10 11 #ifndef __T2080RDB_H 12 #define __T2080RDB_H 13 14 #define CONFIG_DISPLAY_BOARDINFO 15 #define CONFIG_T2080RDB 16 #define CONFIG_ICS307_REFCLK_HZ 25000000 /* ICS307 ref clk freq */ 17 #define CONFIG_MMC 18 #define CONFIG_USB_EHCI 19 #define CONFIG_FSL_SATA_V2 20 21 /* High Level Configuration Options */ 22 #define CONFIG_PHYS_64BIT 23 #define CONFIG_BOOKE 24 #define CONFIG_E500 /* BOOKE e500 family */ 25 #define CONFIG_E500MC /* BOOKE e500mc family */ 26 #define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */ 27 #define CONFIG_MP /* support multiple processors */ 28 #define CONFIG_ENABLE_36BIT_PHYS 29 30 #ifdef CONFIG_PHYS_64BIT 31 #define CONFIG_ADDR_MAP 1 32 #define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */ 33 #endif 34 35 #define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */ 36 #define CONFIG_SYS_NUM_CPC CONFIG_NUM_DDR_CONTROLLERS 37 #define CONFIG_FSL_IFC /* Enable IFC Support */ 38 #define CONFIG_FSL_CAAM /* Enable SEC/CAAM */ 39 #define CONFIG_FSL_LAW /* Use common FSL init code */ 40 #define CONFIG_ENV_OVERWRITE 41 42 #ifdef CONFIG_RAMBOOT_PBL 43 #define CONFIG_SYS_FSL_PBL_PBI board/freescale/t208xrdb/t2080_pbi.cfg 44 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xrdb/t2080_rcw.cfg 45 46 #define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT 47 #define CONFIG_SPL_ENV_SUPPORT 48 #define CONFIG_SPL_SERIAL_SUPPORT 49 #define CONFIG_SPL_FLUSH_IMAGE 50 #define CONFIG_SPL_TARGET "u-boot-with-spl.bin" 51 #define CONFIG_SPL_LIBGENERIC_SUPPORT 52 #define CONFIG_SPL_LIBCOMMON_SUPPORT 53 #define CONFIG_SPL_I2C_SUPPORT 54 #define CONFIG_SPL_DRIVERS_MISC_SUPPORT 55 #define CONFIG_FSL_LAW /* Use common FSL init code */ 56 #define CONFIG_SYS_TEXT_BASE 0x00201000 57 #define CONFIG_SPL_TEXT_BASE 0xFFFD8000 58 #define CONFIG_SPL_PAD_TO 0x40000 59 #define CONFIG_SPL_MAX_SIZE 0x28000 60 #define RESET_VECTOR_OFFSET 0x27FFC 61 #define BOOT_PAGE_OFFSET 0x27000 62 #ifdef CONFIG_SPL_BUILD 63 #define CONFIG_SPL_SKIP_RELOCATE 64 #define CONFIG_SPL_COMMON_INIT_DDR 65 #define CONFIG_SYS_CCSR_DO_NOT_RELOCATE 66 #define CONFIG_SYS_NO_FLASH 67 #endif 68 69 #ifdef CONFIG_NAND 70 #define CONFIG_SPL_NAND_SUPPORT 71 #define CONFIG_SYS_NAND_U_BOOT_SIZE (768 << 10) 72 #define CONFIG_SYS_NAND_U_BOOT_DST 0x00200000 73 #define CONFIG_SYS_NAND_U_BOOT_START 0x00200000 74 #define CONFIG_SYS_NAND_U_BOOT_OFFS (256 << 10) 75 #define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot-nand.lds" 76 #define CONFIG_SPL_NAND_BOOT 77 #endif 78 79 #ifdef CONFIG_SPIFLASH 80 #define CONFIG_RESET_VECTOR_ADDRESS 0x200FFC 81 #define CONFIG_SPL_SPI_SUPPORT 82 #define CONFIG_SPL_SPI_FLASH_SUPPORT 83 #define CONFIG_SPL_SPI_FLASH_MINIMAL 84 #define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE (768 << 10) 85 #define CONFIG_SYS_SPI_FLASH_U_BOOT_DST (0x00200000) 86 #define CONFIG_SYS_SPI_FLASH_U_BOOT_START (0x00200000) 87 #define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS (256 << 10) 88 #define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot.lds" 89 #ifndef CONFIG_SPL_BUILD 90 #define CONFIG_SYS_MPC85XX_NO_RESETVEC 91 #endif 92 #define CONFIG_SPL_SPI_BOOT 93 #endif 94 95 #ifdef CONFIG_SDCARD 96 #define CONFIG_RESET_VECTOR_ADDRESS 0x200FFC 97 #define CONFIG_SPL_MMC_SUPPORT 98 #define CONFIG_SPL_MMC_MINIMAL 99 #define CONFIG_SYS_MMC_U_BOOT_SIZE (768 << 10) 100 #define CONFIG_SYS_MMC_U_BOOT_DST (0x00200000) 101 #define CONFIG_SYS_MMC_U_BOOT_START (0x00200000) 102 #define CONFIG_SYS_MMC_U_BOOT_OFFS (260 << 10) 103 #define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot.lds" 104 #ifndef CONFIG_SPL_BUILD 105 #define CONFIG_SYS_MPC85XX_NO_RESETVEC 106 #endif 107 #define CONFIG_SPL_MMC_BOOT 108 #endif 109 110 #endif /* CONFIG_RAMBOOT_PBL */ 111 112 #define CONFIG_SRIO_PCIE_BOOT_MASTER 113 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE 114 /* Set 1M boot space */ 115 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000) 116 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \ 117 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR) 118 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc 119 #define CONFIG_SYS_NO_FLASH 120 #endif 121 122 #ifndef CONFIG_SYS_TEXT_BASE 123 #define CONFIG_SYS_TEXT_BASE 0xeff40000 124 #endif 125 126 #ifndef CONFIG_RESET_VECTOR_ADDRESS 127 #define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc 128 #endif 129 130 /* 131 * These can be toggled for performance analysis, otherwise use default. 132 */ 133 #define CONFIG_SYS_CACHE_STASHING 134 #define CONFIG_BTB /* toggle branch predition */ 135 #define CONFIG_DDR_ECC 136 #ifdef CONFIG_DDR_ECC 137 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER 138 #define CONFIG_MEM_INIT_VALUE 0xdeadbeef 139 #endif 140 141 #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ 142 #define CONFIG_SYS_MEMTEST_END 0x00400000 143 #define CONFIG_SYS_ALT_MEMTEST 144 145 #ifndef CONFIG_SYS_NO_FLASH 146 #define CONFIG_FLASH_CFI_DRIVER 147 #define CONFIG_SYS_FLASH_CFI 148 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 149 #endif 150 151 #if defined(CONFIG_SPIFLASH) 152 #define CONFIG_SYS_EXTRA_ENV_RELOC 153 #define CONFIG_ENV_IS_IN_SPI_FLASH 154 #define CONFIG_ENV_SPI_BUS 0 155 #define CONFIG_ENV_SPI_CS 0 156 #define CONFIG_ENV_SPI_MAX_HZ 10000000 157 #define CONFIG_ENV_SPI_MODE 0 158 #define CONFIG_ENV_SIZE 0x2000 /* 8KB */ 159 #define CONFIG_ENV_OFFSET 0x100000 /* 1MB */ 160 #define CONFIG_ENV_SECT_SIZE 0x10000 161 #elif defined(CONFIG_SDCARD) 162 #define CONFIG_SYS_EXTRA_ENV_RELOC 163 #define CONFIG_ENV_IS_IN_MMC 164 #define CONFIG_SYS_MMC_ENV_DEV 0 165 #define CONFIG_ENV_SIZE 0x2000 166 #define CONFIG_ENV_OFFSET (512 * 0x800) 167 #elif defined(CONFIG_NAND) 168 #define CONFIG_SYS_EXTRA_ENV_RELOC 169 #define CONFIG_ENV_IS_IN_NAND 170 #define CONFIG_ENV_SIZE 0x2000 171 #define CONFIG_ENV_OFFSET (2 * CONFIG_SYS_NAND_BLOCK_SIZE) 172 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) 173 #define CONFIG_ENV_IS_IN_REMOTE 174 #define CONFIG_ENV_ADDR 0xffe20000 175 #define CONFIG_ENV_SIZE 0x2000 176 #elif defined(CONFIG_ENV_IS_NOWHERE) 177 #define CONFIG_ENV_SIZE 0x2000 178 #else 179 #define CONFIG_ENV_IS_IN_FLASH 180 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) 181 #define CONFIG_ENV_SIZE 0x2000 182 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ 183 #endif 184 185 #ifndef __ASSEMBLY__ 186 unsigned long get_board_sys_clk(void); 187 unsigned long get_board_ddr_clk(void); 188 #endif 189 190 #define CONFIG_SYS_CLK_FREQ 66660000 191 #define CONFIG_DDR_CLK_FREQ 133330000 192 193 /* 194 * Config the L3 Cache as L3 SRAM 195 */ 196 #define CONFIG_SYS_INIT_L3_ADDR 0xFFFC0000 197 #define CONFIG_SYS_L3_SIZE (512 << 10) 198 #define CONFIG_SPL_GD_ADDR (CONFIG_SYS_INIT_L3_ADDR + 32 * 1024) 199 #ifdef CONFIG_RAMBOOT_PBL 200 #define CONFIG_ENV_ADDR (CONFIG_SPL_GD_ADDR + 4 * 1024) 201 #endif 202 #define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SPL_GD_ADDR + 12 * 1024) 203 #define CONFIG_SPL_RELOC_MALLOC_SIZE (50 << 10) 204 #define CONFIG_SPL_RELOC_STACK (CONFIG_SPL_GD_ADDR + 64 * 1024) 205 #define CONFIG_SPL_RELOC_STACK_SIZE (22 << 10) 206 207 #define CONFIG_SYS_DCSRBAR 0xf0000000 208 #define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull 209 210 /* EEPROM */ 211 #define CONFIG_ID_EEPROM 212 #define CONFIG_SYS_I2C_EEPROM_NXID 213 #define CONFIG_SYS_EEPROM_BUS_NUM 0 214 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 215 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 216 217 /* 218 * DDR Setup 219 */ 220 #define CONFIG_VERY_BIG_RAM 221 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 222 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 223 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 224 #define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR) 225 #define CONFIG_DDR_SPD 226 #define CONFIG_SYS_FSL_DDR3 227 #undef CONFIG_FSL_DDR_INTERACTIVE 228 #define CONFIG_SYS_SPD_BUS_NUM 0 229 #define CONFIG_SYS_SDRAM_SIZE 2048 /* for fixed parameter use */ 230 #define SPD_EEPROM_ADDRESS1 0x51 231 #define SPD_EEPROM_ADDRESS2 0x52 232 #define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1 233 #define CTRL_INTLV_PREFERED cacheline 234 235 /* 236 * IFC Definitions 237 */ 238 #define CONFIG_SYS_FLASH_BASE 0xe8000000 239 #define CONFIG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CONFIG_SYS_FLASH_BASE) 240 #define CONFIG_SYS_NOR0_CSPR_EXT (0xf) 241 #define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \ 242 CSPR_PORT_SIZE_16 | \ 243 CSPR_MSEL_NOR | \ 244 CSPR_V) 245 #define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024) 246 247 /* NOR Flash Timing Params */ 248 #define CONFIG_SYS_NOR_CSOR CSOR_NAND_TRHZ_80 249 250 #define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \ 251 FTIM0_NOR_TEADC(0x5) | \ 252 FTIM0_NOR_TEAHC(0x5)) 253 #define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \ 254 FTIM1_NOR_TRAD_NOR(0x1A) |\ 255 FTIM1_NOR_TSEQRAD_NOR(0x13)) 256 #define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \ 257 FTIM2_NOR_TCH(0x4) | \ 258 FTIM2_NOR_TWPH(0x0E) | \ 259 FTIM2_NOR_TWP(0x1c)) 260 #define CONFIG_SYS_NOR_FTIM3 0x0 261 262 #define CONFIG_SYS_FLASH_QUIET_TEST 263 #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ 264 265 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 266 #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ 267 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 268 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 269 #define CONFIG_SYS_FLASH_EMPTY_INFO 270 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS } 271 272 /* CPLD on IFC */ 273 #define CONFIG_SYS_CPLD_BASE 0xffdf0000 274 #define CONFIG_SYS_CPLD_BASE_PHYS (0xf00000000ull | CONFIG_SYS_CPLD_BASE) 275 #define CONFIG_SYS_CSPR2_EXT (0xf) 276 #define CONFIG_SYS_CSPR2 (CSPR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE) \ 277 | CSPR_PORT_SIZE_8 \ 278 | CSPR_MSEL_GPCM \ 279 | CSPR_V) 280 #define CONFIG_SYS_AMASK2 IFC_AMASK(64*1024) 281 #define CONFIG_SYS_CSOR2 0x0 282 283 /* CPLD Timing parameters for IFC CS2 */ 284 #define CONFIG_SYS_CS2_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \ 285 FTIM0_GPCM_TEADC(0x0e) | \ 286 FTIM0_GPCM_TEAHC(0x0e)) 287 #define CONFIG_SYS_CS2_FTIM1 (FTIM1_GPCM_TACO(0x0e) | \ 288 FTIM1_GPCM_TRAD(0x1f)) 289 #define CONFIG_SYS_CS2_FTIM2 (FTIM2_GPCM_TCS(0x0e) | \ 290 FTIM2_GPCM_TCH(0x8) | \ 291 FTIM2_GPCM_TWP(0x1f)) 292 #define CONFIG_SYS_CS2_FTIM3 0x0 293 294 /* NAND Flash on IFC */ 295 #define CONFIG_NAND_FSL_IFC 296 #define CONFIG_SYS_NAND_BASE 0xff800000 297 #define CONFIG_SYS_NAND_BASE_PHYS (0xf00000000ull | CONFIG_SYS_NAND_BASE) 298 299 #define CONFIG_SYS_NAND_CSPR_EXT (0xf) 300 #define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ 301 | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \ 302 | CSPR_MSEL_NAND /* MSEL = NAND */ \ 303 | CSPR_V) 304 #define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024) 305 306 #define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \ 307 | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \ 308 | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \ 309 | CSOR_NAND_RAL_3 /* RAL = 2Byes */ \ 310 | CSOR_NAND_PGS_2K /* Page Size = 2K */\ 311 | CSOR_NAND_SPRZ_64 /* Spare size = 64 */\ 312 | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/ 313 314 #define CONFIG_SYS_NAND_ONFI_DETECTION 315 316 /* ONFI NAND Flash mode0 Timing Params */ 317 #define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \ 318 FTIM0_NAND_TWP(0x18) | \ 319 FTIM0_NAND_TWCHT(0x07) | \ 320 FTIM0_NAND_TWH(0x0a)) 321 #define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \ 322 FTIM1_NAND_TWBE(0x39) | \ 323 FTIM1_NAND_TRR(0x0e) | \ 324 FTIM1_NAND_TRP(0x18)) 325 #define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \ 326 FTIM2_NAND_TREH(0x0a) | \ 327 FTIM2_NAND_TWHRE(0x1e)) 328 #define CONFIG_SYS_NAND_FTIM3 0x0 329 330 #define CONFIG_SYS_NAND_DDR_LAW 11 331 #define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } 332 #define CONFIG_SYS_MAX_NAND_DEVICE 1 333 #define CONFIG_CMD_NAND 334 #define CONFIG_SYS_NAND_BLOCK_SIZE (512 * 1024) 335 336 #if defined(CONFIG_NAND) 337 #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT 338 #define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR 339 #define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK 340 #define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR 341 #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0 342 #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1 343 #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2 344 #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3 345 #define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR0_CSPR_EXT 346 #define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR0_CSPR 347 #define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK 348 #define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR 349 #define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0 350 #define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1 351 #define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2 352 #define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3 353 #else 354 #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT 355 #define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR 356 #define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK 357 #define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR 358 #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0 359 #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1 360 #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2 361 #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3 362 #define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NAND_CSPR_EXT 363 #define CONFIG_SYS_CSPR1 CONFIG_SYS_NAND_CSPR 364 #define CONFIG_SYS_AMASK1 CONFIG_SYS_NAND_AMASK 365 #define CONFIG_SYS_CSOR1 CONFIG_SYS_NAND_CSOR 366 #define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NAND_FTIM0 367 #define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NAND_FTIM1 368 #define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NAND_FTIM2 369 #define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NAND_FTIM3 370 #endif 371 372 #if defined(CONFIG_RAMBOOT_PBL) 373 #define CONFIG_SYS_RAMBOOT 374 #endif 375 376 #ifdef CONFIG_SPL_BUILD 377 #define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE 378 #else 379 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 380 #endif 381 382 #define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */ 383 #define CONFIG_MISC_INIT_R 384 #define CONFIG_HWCONFIG 385 386 /* define to use L1 as initial stack */ 387 #define CONFIG_L1_INIT_RAM 388 #define CONFIG_SYS_INIT_RAM_LOCK 389 #define CONFIG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */ 390 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf 391 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW 0xfe03c000 392 /* The assembler doesn't like typecast */ 393 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \ 394 ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \ 395 CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW) 396 #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 397 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ 398 GENERATED_GBL_DATA_SIZE) 399 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 400 #define CONFIG_SYS_MONITOR_LEN (768 * 1024) 401 #define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024) 402 403 /* 404 * Serial Port 405 */ 406 #define CONFIG_CONS_INDEX 1 407 #define CONFIG_SYS_NS16550_SERIAL 408 #define CONFIG_SYS_NS16550_REG_SIZE 1 409 #define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2) 410 #define CONFIG_SYS_BAUDRATE_TABLE \ 411 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} 412 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500) 413 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600) 414 #define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500) 415 #define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600) 416 417 /* 418 * I2C 419 */ 420 #define CONFIG_SYS_I2C 421 #define CONFIG_SYS_I2C_FSL 422 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 423 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F 424 #define CONFIG_SYS_FSL_I2C3_SLAVE 0x7F 425 #define CONFIG_SYS_FSL_I2C4_SLAVE 0x7F 426 #define CONFIG_SYS_FSL_I2C_OFFSET 0x118000 427 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100 428 #define CONFIG_SYS_FSL_I2C3_OFFSET 0x119000 429 #define CONFIG_SYS_FSL_I2C4_OFFSET 0x119100 430 #define CONFIG_SYS_FSL_I2C_SPEED 100000 431 #define CONFIG_SYS_FSL_I2C2_SPEED 100000 432 #define CONFIG_SYS_FSL_I2C3_SPEED 100000 433 #define CONFIG_SYS_FSL_I2C4_SPEED 100000 434 #define I2C_MUX_PCA_ADDR_PRI 0x77 /* I2C bus multiplexer,primary */ 435 #define I2C_MUX_PCA_ADDR_SEC1 0x75 /* I2C bus multiplexer,secondary 1 */ 436 #define I2C_MUX_PCA_ADDR_SEC2 0x76 /* I2C bus multiplexer,secondary 2 */ 437 #define I2C_MUX_CH_DEFAULT 0x8 438 439 #define I2C_MUX_CH_VOL_MONITOR 0xa 440 441 #define CONFIG_VID_FLS_ENV "t208xrdb_vdd_mv" 442 #ifndef CONFIG_SPL_BUILD 443 #define CONFIG_VID 444 #endif 445 #define CONFIG_VOL_MONITOR_IR36021_SET 446 #define CONFIG_VOL_MONITOR_IR36021_READ 447 /* The lowest and highest voltage allowed for T208xRDB */ 448 #define VDD_MV_MIN 819 449 #define VDD_MV_MAX 1212 450 451 /* 452 * RapidIO 453 */ 454 #define CONFIG_SYS_SRIO1_MEM_VIRT 0xa0000000 455 #define CONFIG_SYS_SRIO1_MEM_PHYS 0xc20000000ull 456 #define CONFIG_SYS_SRIO1_MEM_SIZE 0x10000000 /* 256M */ 457 #define CONFIG_SYS_SRIO2_MEM_VIRT 0xb0000000 458 #define CONFIG_SYS_SRIO2_MEM_PHYS 0xc30000000ull 459 #define CONFIG_SYS_SRIO2_MEM_SIZE 0x10000000 /* 256M */ 460 /* 461 * for slave u-boot IMAGE instored in master memory space, 462 * PHYS must be aligned based on the SIZE 463 */ 464 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull 465 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull 466 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x100000 /* 1M */ 467 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull 468 /* 469 * for slave UCODE and ENV instored in master memory space, 470 * PHYS must be aligned based on the SIZE 471 */ 472 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull 473 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull 474 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */ 475 476 /* slave core release by master*/ 477 #define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4 478 #define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */ 479 480 /* 481 * SRIO_PCIE_BOOT - SLAVE 482 */ 483 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE 484 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000 485 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \ 486 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR) 487 #endif 488 489 /* 490 * eSPI - Enhanced SPI 491 */ 492 #ifdef CONFIG_SPI_FLASH 493 #define CONFIG_SPI_FLASH_BAR 494 #define CONFIG_SF_DEFAULT_SPEED 10000000 495 #define CONFIG_SF_DEFAULT_MODE 0 496 #endif 497 498 /* 499 * General PCI 500 * Memory space is mapped 1-1, but I/O space must start from 0. 501 */ 502 #define CONFIG_PCI /* Enable PCI/PCIE */ 503 #define CONFIG_PCIE1 /* PCIE controller 1 */ 504 #define CONFIG_PCIE2 /* PCIE controller 2 */ 505 #define CONFIG_PCIE3 /* PCIE controller 3 */ 506 #define CONFIG_PCIE4 /* PCIE controller 4 */ 507 #define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ 508 #define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ 509 /* controller 1, direct to uli, tgtid 3, Base address 20000 */ 510 #define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 511 #define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 512 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull 513 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ 514 #define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000 515 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 516 #define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull 517 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ 518 519 /* controller 2, Slot 2, tgtid 2, Base address 201000 */ 520 #define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 521 #define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000 522 #define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull 523 #define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */ 524 #define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000 525 #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 526 #define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull 527 #define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ 528 529 /* controller 3, Slot 1, tgtid 1, Base address 202000 */ 530 #define CONFIG_SYS_PCIE3_MEM_VIRT 0xb0000000 531 #define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000 532 #define CONFIG_SYS_PCIE3_MEM_PHYS 0xc30000000ull 533 #define CONFIG_SYS_PCIE3_MEM_SIZE 0x10000000 /* 256M */ 534 #define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000 535 #define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 536 #define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull 537 #define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */ 538 539 /* controller 4, Base address 203000 */ 540 #define CONFIG_SYS_PCIE4_MEM_VIRT 0xc0000000 541 #define CONFIG_SYS_PCIE4_MEM_BUS 0xe0000000 542 #define CONFIG_SYS_PCIE4_MEM_PHYS 0xc40000000ull 543 #define CONFIG_SYS_PCIE4_MEM_SIZE 0x10000000 /* 256M */ 544 #define CONFIG_SYS_PCIE4_IO_BUS 0x00000000 545 #define CONFIG_SYS_PCIE4_IO_PHYS 0xff8030000ull 546 #define CONFIG_SYS_PCIE4_IO_SIZE 0x00010000 /* 64k */ 547 548 #ifdef CONFIG_PCI 549 #define CONFIG_PCI_INDIRECT_BRIDGE 550 #define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata LSZ ADD */ 551 #define CONFIG_PCI_PNP /* do pci plug-and-play */ 552 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 553 #define CONFIG_DOS_PARTITION 554 #endif 555 556 /* Qman/Bman */ 557 #ifndef CONFIG_NOBQFMAN 558 #define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */ 559 #define CONFIG_SYS_BMAN_NUM_PORTALS 18 560 #define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000 561 #define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull 562 #define CONFIG_SYS_BMAN_MEM_SIZE 0x02000000 563 #define CONFIG_SYS_BMAN_SP_CENA_SIZE 0x4000 564 #define CONFIG_SYS_BMAN_SP_CINH_SIZE 0x1000 565 #define CONFIG_SYS_BMAN_CENA_BASE CONFIG_SYS_BMAN_MEM_BASE 566 #define CONFIG_SYS_BMAN_CENA_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) 567 #define CONFIG_SYS_BMAN_CINH_BASE (CONFIG_SYS_BMAN_MEM_BASE + \ 568 CONFIG_SYS_BMAN_CENA_SIZE) 569 #define CONFIG_SYS_BMAN_CINH_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) 570 #define CONFIG_SYS_BMAN_SWP_ISDR_REG 0xE08 571 #define CONFIG_SYS_QMAN_NUM_PORTALS 18 572 #define CONFIG_SYS_QMAN_MEM_BASE 0xf6000000 573 #define CONFIG_SYS_QMAN_MEM_PHYS 0xff6000000ull 574 #define CONFIG_SYS_QMAN_MEM_SIZE 0x02000000 575 #define CONFIG_SYS_QMAN_SP_CENA_SIZE 0x4000 576 #define CONFIG_SYS_QMAN_SP_CINH_SIZE 0x1000 577 #define CONFIG_SYS_QMAN_CENA_BASE CONFIG_SYS_QMAN_MEM_BASE 578 #define CONFIG_SYS_QMAN_CENA_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) 579 #define CONFIG_SYS_QMAN_CINH_BASE (CONFIG_SYS_QMAN_MEM_BASE + \ 580 CONFIG_SYS_QMAN_CENA_SIZE) 581 #define CONFIG_SYS_QMAN_CINH_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) 582 #define CONFIG_SYS_QMAN_SWP_ISDR_REG 0xE08 583 584 #define CONFIG_SYS_DPAA_FMAN 585 #define CONFIG_SYS_DPAA_PME 586 #define CONFIG_SYS_PMAN 587 #define CONFIG_SYS_DPAA_DCE 588 #define CONFIG_SYS_DPAA_RMAN /* RMan */ 589 #define CONFIG_SYS_INTERLAKEN 590 591 /* Default address of microcode for the Linux Fman driver */ 592 #if defined(CONFIG_SPIFLASH) 593 /* 594 * env is stored at 0x100000, sector size is 0x10000, ucode is stored after 595 * env, so we got 0x110000. 596 */ 597 #define CONFIG_SYS_QE_FW_IN_SPIFLASH 598 #define CONFIG_SYS_CORTINA_FW_IN_SPIFLASH 599 #define CONFIG_SYS_FMAN_FW_ADDR 0x110000 600 #define CONFIG_CORTINA_FW_ADDR 0x120000 601 602 #elif defined(CONFIG_SDCARD) 603 /* 604 * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is 605 * about 1MB (2048 blocks), Env is stored after the image, and the env size is 606 * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080. 607 */ 608 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC 609 #define CONFIG_SYS_CORTINA_FW_IN_MMC 610 #define CONFIG_SYS_FMAN_FW_ADDR (512 * 0x820) 611 #define CONFIG_CORTINA_FW_ADDR (512 * 0x8a0) 612 613 #elif defined(CONFIG_NAND) 614 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND 615 #define CONFIG_SYS_CORTINA_FW_IN_NAND 616 #define CONFIG_SYS_FMAN_FW_ADDR (3 * CONFIG_SYS_NAND_BLOCK_SIZE) 617 #define CONFIG_CORTINA_FW_ADDR (4 * CONFIG_SYS_NAND_BLOCK_SIZE) 618 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) 619 /* 620 * Slave has no ucode locally, it can fetch this from remote. When implementing 621 * in two corenet boards, slave's ucode could be stored in master's memory 622 * space, the address can be mapped from slave TLB->slave LAW-> 623 * slave SRIO or PCIE outbound window->master inbound window-> 624 * master LAW->the ucode address in master's memory space. 625 */ 626 #define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE 627 #define CONFIG_SYS_CORTINA_FW_IN_REMOTE 628 #define CONFIG_SYS_FMAN_FW_ADDR 0xFFE00000 629 #define CONFIG_CORTINA_FW_ADDR 0xFFE10000 630 #else 631 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR 632 #define CONFIG_SYS_CORTINA_FW_IN_NOR 633 #define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000 634 #define CONFIG_CORTINA_FW_ADDR 0xEFE00000 635 #endif 636 #define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 637 #define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) 638 #endif /* CONFIG_NOBQFMAN */ 639 640 #ifdef CONFIG_SYS_DPAA_FMAN 641 #define CONFIG_FMAN_ENET 642 #define CONFIG_PHYLIB_10G 643 #define CONFIG_PHY_AQUANTIA 644 #define CONFIG_PHY_CORTINA 645 #define CONFIG_PHY_REALTEK 646 #define CONFIG_CORTINA_FW_LENGTH 0x40000 647 #define RGMII_PHY1_ADDR 0x01 /* RealTek RTL8211E */ 648 #define RGMII_PHY2_ADDR 0x02 649 #define CORTINA_PHY_ADDR1 0x0c /* Cortina CS4315 */ 650 #define CORTINA_PHY_ADDR2 0x0d 651 #define FM1_10GEC3_PHY_ADDR 0x00 /* Aquantia AQ1202 10G Base-T */ 652 #define FM1_10GEC4_PHY_ADDR 0x01 653 #endif 654 655 #ifdef CONFIG_FMAN_ENET 656 #define CONFIG_MII /* MII PHY management */ 657 #define CONFIG_ETHPRIME "FM1@DTSEC3" 658 #define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ 659 #endif 660 661 /* 662 * SATA 663 */ 664 #ifdef CONFIG_FSL_SATA_V2 665 #define CONFIG_LIBATA 666 #define CONFIG_FSL_SATA 667 #define CONFIG_SYS_SATA_MAX_DEVICE 2 668 #define CONFIG_SATA1 669 #define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR 670 #define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA 671 #define CONFIG_SATA2 672 #define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR 673 #define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA 674 #define CONFIG_LBA48 675 #define CONFIG_CMD_SATA 676 #define CONFIG_DOS_PARTITION 677 #endif 678 679 /* 680 * USB 681 */ 682 #ifdef CONFIG_USB_EHCI 683 #define CONFIG_USB_STORAGE 684 #define CONFIG_USB_EHCI_FSL 685 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET 686 #define CONFIG_HAS_FSL_DR_USB 687 #endif 688 689 /* 690 * SDHC 691 */ 692 #ifdef CONFIG_MMC 693 #define CONFIG_FSL_ESDHC 694 #define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR 695 #define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT 696 #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33 697 #define CONFIG_GENERIC_MMC 698 #define CONFIG_DOS_PARTITION 699 #endif 700 701 /* 702 * Dynamic MTD Partition support with mtdparts 703 */ 704 #ifndef CONFIG_SYS_NO_FLASH 705 #define CONFIG_MTD_DEVICE 706 #define CONFIG_MTD_PARTITIONS 707 #define CONFIG_CMD_MTDPARTS 708 #define CONFIG_FLASH_CFI_MTD 709 #define MTDIDS_DEFAULT "nor0=fe8000000.nor,nand0=fff800000.flash," \ 710 "spi0=spife110000.1" 711 #define MTDPARTS_DEFAULT "mtdparts=fe8000000.nor:1m(uboot),5m(kernel)," \ 712 "128k(dtb),96m(fs),-(user);fff800000.flash:1m(uboot)," \ 713 "5m(kernel),128k(dtb),96m(fs),-(user);spife110000.1:" \ 714 "1m(uboot),5m(kernel),128k(dtb),-(user)" 715 #endif 716 717 /* 718 * Environment 719 */ 720 721 /* 722 * Command line configuration. 723 */ 724 #define CONFIG_CMD_ERRATA 725 #define CONFIG_CMD_REGINFO 726 727 #ifdef CONFIG_PCI 728 #define CONFIG_CMD_PCI 729 #endif 730 731 /* Hash command with SHA acceleration supported in hardware */ 732 #ifdef CONFIG_FSL_CAAM 733 #define CONFIG_CMD_HASH 734 #define CONFIG_SHA_HW_ACCEL 735 #endif 736 737 /* 738 * Miscellaneous configurable options 739 */ 740 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 741 #define CONFIG_CMDLINE_EDITING /* Command-line editing */ 742 #define CONFIG_AUTO_COMPLETE /* add autocompletion support */ 743 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 744 #ifdef CONFIG_CMD_KGDB 745 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 746 #else 747 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 748 #endif 749 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) 750 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 751 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */ 752 753 /* 754 * For booting Linux, the board info and command line data 755 * have to be in the first 64 MB of memory, since this is 756 * the maximum mapped by the Linux kernel during initialization. 757 */ 758 #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial map for Linux*/ 759 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 760 761 #ifdef CONFIG_CMD_KGDB 762 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ 763 #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ 764 #endif 765 766 /* 767 * Environment Configuration 768 */ 769 #define CONFIG_ROOTPATH "/opt/nfsroot" 770 #define CONFIG_BOOTFILE "uImage" 771 #define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server */ 772 773 /* default location for tftp and bootm */ 774 #define CONFIG_LOADADDR 1000000 775 #define CONFIG_BAUDRATE 115200 776 #define __USB_PHY_TYPE utmi 777 778 #define CONFIG_EXTRA_ENV_SETTINGS \ 779 "hwconfig=fsl_ddr:" \ 780 "ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) "," \ 781 "bank_intlv=auto;" \ 782 "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\ 783 "netdev=eth0\0" \ 784 "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ 785 "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \ 786 "tftpflash=tftpboot $loadaddr $uboot && " \ 787 "protect off $ubootaddr +$filesize && " \ 788 "erase $ubootaddr +$filesize && " \ 789 "cp.b $loadaddr $ubootaddr $filesize && " \ 790 "protect on $ubootaddr +$filesize && " \ 791 "cmp.b $loadaddr $ubootaddr $filesize\0" \ 792 "consoledev=ttyS0\0" \ 793 "ramdiskaddr=2000000\0" \ 794 "ramdiskfile=t2080rdb/ramdisk.uboot\0" \ 795 "fdtaddr=1e00000\0" \ 796 "fdtfile=t2080rdb/t2080rdb.dtb\0" \ 797 "bdev=sda3\0" 798 799 /* 800 * For emulation this causes u-boot to jump to the start of the 801 * proof point app code automatically 802 */ 803 #define CONFIG_PROOF_POINTS \ 804 "setenv bootargs root=/dev/$bdev rw " \ 805 "console=$consoledev,$baudrate $othbootargs;" \ 806 "cpu 1 release 0x29000000 - - -;" \ 807 "cpu 2 release 0x29000000 - - -;" \ 808 "cpu 3 release 0x29000000 - - -;" \ 809 "cpu 4 release 0x29000000 - - -;" \ 810 "cpu 5 release 0x29000000 - - -;" \ 811 "cpu 6 release 0x29000000 - - -;" \ 812 "cpu 7 release 0x29000000 - - -;" \ 813 "go 0x29000000" 814 815 #define CONFIG_HVBOOT \ 816 "setenv bootargs config-addr=0x60000000; " \ 817 "bootm 0x01000000 - 0x00f00000" 818 819 #define CONFIG_ALU \ 820 "setenv bootargs root=/dev/$bdev rw " \ 821 "console=$consoledev,$baudrate $othbootargs;" \ 822 "cpu 1 release 0x01000000 - - -;" \ 823 "cpu 2 release 0x01000000 - - -;" \ 824 "cpu 3 release 0x01000000 - - -;" \ 825 "cpu 4 release 0x01000000 - - -;" \ 826 "cpu 5 release 0x01000000 - - -;" \ 827 "cpu 6 release 0x01000000 - - -;" \ 828 "cpu 7 release 0x01000000 - - -;" \ 829 "go 0x01000000" 830 831 #define CONFIG_LINUX \ 832 "setenv bootargs root=/dev/ram rw " \ 833 "console=$consoledev,$baudrate $othbootargs;" \ 834 "setenv ramdiskaddr 0x02000000;" \ 835 "setenv fdtaddr 0x00c00000;" \ 836 "setenv loadaddr 0x1000000;" \ 837 "bootm $loadaddr $ramdiskaddr $fdtaddr" 838 839 #define CONFIG_HDBOOT \ 840 "setenv bootargs root=/dev/$bdev rw " \ 841 "console=$consoledev,$baudrate $othbootargs;" \ 842 "tftp $loadaddr $bootfile;" \ 843 "tftp $fdtaddr $fdtfile;" \ 844 "bootm $loadaddr - $fdtaddr" 845 846 #define CONFIG_NFSBOOTCOMMAND \ 847 "setenv bootargs root=/dev/nfs rw " \ 848 "nfsroot=$serverip:$rootpath " \ 849 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 850 "console=$consoledev,$baudrate $othbootargs;" \ 851 "tftp $loadaddr $bootfile;" \ 852 "tftp $fdtaddr $fdtfile;" \ 853 "bootm $loadaddr - $fdtaddr" 854 855 #define CONFIG_RAMBOOTCOMMAND \ 856 "setenv bootargs root=/dev/ram rw " \ 857 "console=$consoledev,$baudrate $othbootargs;" \ 858 "tftp $ramdiskaddr $ramdiskfile;" \ 859 "tftp $loadaddr $bootfile;" \ 860 "tftp $fdtaddr $fdtfile;" \ 861 "bootm $loadaddr $ramdiskaddr $fdtaddr" 862 863 #define CONFIG_BOOTCOMMAND CONFIG_LINUX 864 865 #include <asm/fsl_secure_boot.h> 866 867 #endif /* __T2080RDB_H */ 868