1 /* SPDX-License-Identifier: GPL-2.0+ */ 2 /* 3 * Copyright 2014 Freescale Semiconductor, Inc. 4 */ 5 6 /* 7 * T2080 RDB/PCIe board configuration file 8 */ 9 10 #ifndef __T2080RDB_H 11 #define __T2080RDB_H 12 13 #define CONFIG_ICS307_REFCLK_HZ 25000000 /* ICS307 ref clk freq */ 14 #define CONFIG_FSL_SATA_V2 15 16 /* High Level Configuration Options */ 17 #define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */ 18 #define CONFIG_ENABLE_36BIT_PHYS 19 20 #ifdef CONFIG_PHYS_64BIT 21 #define CONFIG_ADDR_MAP 1 22 #define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */ 23 #endif 24 25 #define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */ 26 #define CONFIG_SYS_NUM_CPC CONFIG_SYS_NUM_DDR_CTLRS 27 #define CONFIG_ENV_OVERWRITE 28 29 #ifdef CONFIG_RAMBOOT_PBL 30 #define CONFIG_SYS_FSL_PBL_PBI board/freescale/t208xrdb/t2080_pbi.cfg 31 32 #define CONFIG_SPL_FLUSH_IMAGE 33 #define CONFIG_SPL_TEXT_BASE 0xFFFD8000 34 #define CONFIG_SPL_PAD_TO 0x40000 35 #define CONFIG_SPL_MAX_SIZE 0x28000 36 #define RESET_VECTOR_OFFSET 0x27FFC 37 #define BOOT_PAGE_OFFSET 0x27000 38 #ifdef CONFIG_SPL_BUILD 39 #define CONFIG_SPL_SKIP_RELOCATE 40 #define CONFIG_SPL_COMMON_INIT_DDR 41 #define CONFIG_SYS_CCSR_DO_NOT_RELOCATE 42 #endif 43 44 #ifdef CONFIG_NAND 45 #define CONFIG_SYS_NAND_U_BOOT_SIZE (768 << 10) 46 #define CONFIG_SYS_NAND_U_BOOT_DST 0x00200000 47 #define CONFIG_SYS_NAND_U_BOOT_START 0x00200000 48 #define CONFIG_SYS_NAND_U_BOOT_OFFS (256 << 10) 49 #define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot-nand.lds" 50 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xrdb/t2080_nand_rcw.cfg 51 #define CONFIG_SPL_NAND_BOOT 52 #endif 53 54 #ifdef CONFIG_SPIFLASH 55 #define CONFIG_RESET_VECTOR_ADDRESS 0x200FFC 56 #define CONFIG_SPL_SPI_FLASH_MINIMAL 57 #define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE (768 << 10) 58 #define CONFIG_SYS_SPI_FLASH_U_BOOT_DST (0x00200000) 59 #define CONFIG_SYS_SPI_FLASH_U_BOOT_START (0x00200000) 60 #define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS (256 << 10) 61 #define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot.lds" 62 #ifndef CONFIG_SPL_BUILD 63 #define CONFIG_SYS_MPC85XX_NO_RESETVEC 64 #endif 65 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xrdb/t2080_spi_rcw.cfg 66 #define CONFIG_SPL_SPI_BOOT 67 #endif 68 69 #ifdef CONFIG_SDCARD 70 #define CONFIG_RESET_VECTOR_ADDRESS 0x200FFC 71 #define CONFIG_SYS_MMC_U_BOOT_SIZE (768 << 10) 72 #define CONFIG_SYS_MMC_U_BOOT_DST (0x00200000) 73 #define CONFIG_SYS_MMC_U_BOOT_START (0x00200000) 74 #define CONFIG_SYS_MMC_U_BOOT_OFFS (260 << 10) 75 #define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot.lds" 76 #ifndef CONFIG_SPL_BUILD 77 #define CONFIG_SYS_MPC85XX_NO_RESETVEC 78 #endif 79 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xrdb/t2080_sd_rcw.cfg 80 #define CONFIG_SPL_MMC_BOOT 81 #endif 82 83 #endif /* CONFIG_RAMBOOT_PBL */ 84 85 #define CONFIG_SRIO_PCIE_BOOT_MASTER 86 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE 87 /* Set 1M boot space */ 88 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000) 89 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \ 90 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR) 91 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc 92 #endif 93 94 #ifndef CONFIG_RESET_VECTOR_ADDRESS 95 #define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc 96 #endif 97 98 /* 99 * These can be toggled for performance analysis, otherwise use default. 100 */ 101 #define CONFIG_SYS_CACHE_STASHING 102 #define CONFIG_BTB /* toggle branch predition */ 103 #define CONFIG_DDR_ECC 104 #ifdef CONFIG_DDR_ECC 105 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER 106 #define CONFIG_MEM_INIT_VALUE 0xdeadbeef 107 #endif 108 109 #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ 110 #define CONFIG_SYS_MEMTEST_END 0x00400000 111 112 #if defined(CONFIG_SPIFLASH) 113 #define CONFIG_ENV_SPI_BUS 0 114 #define CONFIG_ENV_SPI_CS 0 115 #define CONFIG_ENV_SPI_MAX_HZ 10000000 116 #define CONFIG_ENV_SPI_MODE 0 117 #define CONFIG_ENV_SIZE 0x2000 /* 8KB */ 118 #define CONFIG_ENV_OFFSET 0x100000 /* 1MB */ 119 #define CONFIG_ENV_SECT_SIZE 0x10000 120 #elif defined(CONFIG_SDCARD) 121 #define CONFIG_SYS_MMC_ENV_DEV 0 122 #define CONFIG_ENV_SIZE 0x2000 123 #define CONFIG_ENV_OFFSET (512 * 0x800) 124 #elif defined(CONFIG_NAND) 125 #define CONFIG_ENV_SIZE 0x2000 126 #define CONFIG_ENV_OFFSET (2 * CONFIG_SYS_NAND_BLOCK_SIZE) 127 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) 128 #define CONFIG_ENV_ADDR 0xffe20000 129 #define CONFIG_ENV_SIZE 0x2000 130 #elif defined(CONFIG_ENV_IS_NOWHERE) 131 #define CONFIG_ENV_SIZE 0x2000 132 #else 133 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) 134 #define CONFIG_ENV_SIZE 0x2000 135 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ 136 #endif 137 138 #ifndef __ASSEMBLY__ 139 unsigned long get_board_sys_clk(void); 140 unsigned long get_board_ddr_clk(void); 141 #endif 142 143 #define CONFIG_SYS_CLK_FREQ 66660000 144 #define CONFIG_DDR_CLK_FREQ 133330000 145 146 /* 147 * Config the L3 Cache as L3 SRAM 148 */ 149 #define CONFIG_SYS_INIT_L3_ADDR 0xFFFC0000 150 #define CONFIG_SYS_L3_SIZE (512 << 10) 151 #define CONFIG_SPL_GD_ADDR (CONFIG_SYS_INIT_L3_ADDR + 32 * 1024) 152 #ifdef CONFIG_RAMBOOT_PBL 153 #define CONFIG_ENV_ADDR (CONFIG_SPL_GD_ADDR + 4 * 1024) 154 #endif 155 #define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SPL_GD_ADDR + 12 * 1024) 156 #define CONFIG_SPL_RELOC_MALLOC_SIZE (50 << 10) 157 #define CONFIG_SPL_RELOC_STACK (CONFIG_SPL_GD_ADDR + 64 * 1024) 158 159 #define CONFIG_SYS_DCSRBAR 0xf0000000 160 #define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull 161 162 /* EEPROM */ 163 #define CONFIG_ID_EEPROM 164 #define CONFIG_SYS_I2C_EEPROM_NXID 165 #define CONFIG_SYS_EEPROM_BUS_NUM 0 166 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 167 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 168 169 /* 170 * DDR Setup 171 */ 172 #define CONFIG_VERY_BIG_RAM 173 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 174 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 175 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 176 #define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR) 177 #define CONFIG_DDR_SPD 178 #undef CONFIG_FSL_DDR_INTERACTIVE 179 #define CONFIG_SYS_SPD_BUS_NUM 0 180 #define CONFIG_SYS_SDRAM_SIZE 2048 /* for fixed parameter use */ 181 #define SPD_EEPROM_ADDRESS1 0x51 182 #define SPD_EEPROM_ADDRESS2 0x52 183 #define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1 184 #define CTRL_INTLV_PREFERED cacheline 185 186 /* 187 * IFC Definitions 188 */ 189 #define CONFIG_SYS_FLASH_BASE 0xe8000000 190 #define CONFIG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CONFIG_SYS_FLASH_BASE) 191 #define CONFIG_SYS_NOR0_CSPR_EXT (0xf) 192 #define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \ 193 CSPR_PORT_SIZE_16 | \ 194 CSPR_MSEL_NOR | \ 195 CSPR_V) 196 #define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024) 197 198 /* NOR Flash Timing Params */ 199 #define CONFIG_SYS_NOR_CSOR CSOR_NAND_TRHZ_80 200 201 #define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \ 202 FTIM0_NOR_TEADC(0x5) | \ 203 FTIM0_NOR_TEAHC(0x5)) 204 #define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \ 205 FTIM1_NOR_TRAD_NOR(0x1A) |\ 206 FTIM1_NOR_TSEQRAD_NOR(0x13)) 207 #define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \ 208 FTIM2_NOR_TCH(0x4) | \ 209 FTIM2_NOR_TWPH(0x0E) | \ 210 FTIM2_NOR_TWP(0x1c)) 211 #define CONFIG_SYS_NOR_FTIM3 0x0 212 213 #define CONFIG_SYS_FLASH_QUIET_TEST 214 #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ 215 216 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 217 #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ 218 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 219 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 220 #define CONFIG_SYS_FLASH_EMPTY_INFO 221 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS } 222 223 /* CPLD on IFC */ 224 #define CONFIG_SYS_CPLD_BASE 0xffdf0000 225 #define CONFIG_SYS_CPLD_BASE_PHYS (0xf00000000ull | CONFIG_SYS_CPLD_BASE) 226 #define CONFIG_SYS_CSPR2_EXT (0xf) 227 #define CONFIG_SYS_CSPR2 (CSPR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE) \ 228 | CSPR_PORT_SIZE_8 \ 229 | CSPR_MSEL_GPCM \ 230 | CSPR_V) 231 #define CONFIG_SYS_AMASK2 IFC_AMASK(64*1024) 232 #define CONFIG_SYS_CSOR2 0x0 233 234 /* CPLD Timing parameters for IFC CS2 */ 235 #define CONFIG_SYS_CS2_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \ 236 FTIM0_GPCM_TEADC(0x0e) | \ 237 FTIM0_GPCM_TEAHC(0x0e)) 238 #define CONFIG_SYS_CS2_FTIM1 (FTIM1_GPCM_TACO(0x0e) | \ 239 FTIM1_GPCM_TRAD(0x1f)) 240 #define CONFIG_SYS_CS2_FTIM2 (FTIM2_GPCM_TCS(0x0e) | \ 241 FTIM2_GPCM_TCH(0x8) | \ 242 FTIM2_GPCM_TWP(0x1f)) 243 #define CONFIG_SYS_CS2_FTIM3 0x0 244 245 /* NAND Flash on IFC */ 246 #define CONFIG_NAND_FSL_IFC 247 #define CONFIG_SYS_NAND_BASE 0xff800000 248 #define CONFIG_SYS_NAND_BASE_PHYS (0xf00000000ull | CONFIG_SYS_NAND_BASE) 249 250 #define CONFIG_SYS_NAND_CSPR_EXT (0xf) 251 #define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ 252 | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \ 253 | CSPR_MSEL_NAND /* MSEL = NAND */ \ 254 | CSPR_V) 255 #define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024) 256 257 #define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \ 258 | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \ 259 | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \ 260 | CSOR_NAND_RAL_3 /* RAL = 2Byes */ \ 261 | CSOR_NAND_PGS_2K /* Page Size = 2K */\ 262 | CSOR_NAND_SPRZ_64 /* Spare size = 64 */\ 263 | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/ 264 265 #define CONFIG_SYS_NAND_ONFI_DETECTION 266 267 /* ONFI NAND Flash mode0 Timing Params */ 268 #define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \ 269 FTIM0_NAND_TWP(0x18) | \ 270 FTIM0_NAND_TWCHT(0x07) | \ 271 FTIM0_NAND_TWH(0x0a)) 272 #define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \ 273 FTIM1_NAND_TWBE(0x39) | \ 274 FTIM1_NAND_TRR(0x0e) | \ 275 FTIM1_NAND_TRP(0x18)) 276 #define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \ 277 FTIM2_NAND_TREH(0x0a) | \ 278 FTIM2_NAND_TWHRE(0x1e)) 279 #define CONFIG_SYS_NAND_FTIM3 0x0 280 281 #define CONFIG_SYS_NAND_DDR_LAW 11 282 #define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } 283 #define CONFIG_SYS_MAX_NAND_DEVICE 1 284 #define CONFIG_SYS_NAND_BLOCK_SIZE (512 * 1024) 285 286 #if defined(CONFIG_NAND) 287 #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT 288 #define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR 289 #define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK 290 #define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR 291 #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0 292 #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1 293 #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2 294 #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3 295 #define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR0_CSPR_EXT 296 #define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR0_CSPR 297 #define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK 298 #define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR 299 #define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0 300 #define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1 301 #define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2 302 #define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3 303 #else 304 #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT 305 #define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR 306 #define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK 307 #define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR 308 #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0 309 #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1 310 #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2 311 #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3 312 #define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NAND_CSPR_EXT 313 #define CONFIG_SYS_CSPR1 CONFIG_SYS_NAND_CSPR 314 #define CONFIG_SYS_AMASK1 CONFIG_SYS_NAND_AMASK 315 #define CONFIG_SYS_CSOR1 CONFIG_SYS_NAND_CSOR 316 #define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NAND_FTIM0 317 #define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NAND_FTIM1 318 #define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NAND_FTIM2 319 #define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NAND_FTIM3 320 #endif 321 322 #if defined(CONFIG_RAMBOOT_PBL) 323 #define CONFIG_SYS_RAMBOOT 324 #endif 325 326 #ifdef CONFIG_SPL_BUILD 327 #define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE 328 #else 329 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 330 #endif 331 332 #define CONFIG_HWCONFIG 333 334 /* define to use L1 as initial stack */ 335 #define CONFIG_L1_INIT_RAM 336 #define CONFIG_SYS_INIT_RAM_LOCK 337 #define CONFIG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */ 338 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf 339 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW 0xfe03c000 340 /* The assembler doesn't like typecast */ 341 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \ 342 ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \ 343 CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW) 344 #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 345 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ 346 GENERATED_GBL_DATA_SIZE) 347 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 348 #define CONFIG_SYS_MONITOR_LEN (768 * 1024) 349 #define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024) 350 351 /* 352 * Serial Port 353 */ 354 #define CONFIG_SYS_NS16550_SERIAL 355 #define CONFIG_SYS_NS16550_REG_SIZE 1 356 #define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2) 357 #define CONFIG_SYS_BAUDRATE_TABLE \ 358 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} 359 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500) 360 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600) 361 #define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500) 362 #define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600) 363 364 /* 365 * I2C 366 */ 367 #define CONFIG_SYS_I2C 368 #define CONFIG_SYS_I2C_FSL 369 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 370 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F 371 #define CONFIG_SYS_FSL_I2C3_SLAVE 0x7F 372 #define CONFIG_SYS_FSL_I2C4_SLAVE 0x7F 373 #define CONFIG_SYS_FSL_I2C_OFFSET 0x118000 374 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100 375 #define CONFIG_SYS_FSL_I2C3_OFFSET 0x119000 376 #define CONFIG_SYS_FSL_I2C4_OFFSET 0x119100 377 #define CONFIG_SYS_FSL_I2C_SPEED 100000 378 #define CONFIG_SYS_FSL_I2C2_SPEED 100000 379 #define CONFIG_SYS_FSL_I2C3_SPEED 100000 380 #define CONFIG_SYS_FSL_I2C4_SPEED 100000 381 #define I2C_MUX_PCA_ADDR_PRI 0x77 /* I2C bus multiplexer,primary */ 382 #define I2C_MUX_PCA_ADDR_SEC1 0x75 /* I2C bus multiplexer,secondary 1 */ 383 #define I2C_MUX_PCA_ADDR_SEC2 0x76 /* I2C bus multiplexer,secondary 2 */ 384 #define I2C_MUX_CH_DEFAULT 0x8 385 386 #define I2C_MUX_CH_VOL_MONITOR 0xa 387 388 #define CONFIG_VID_FLS_ENV "t208xrdb_vdd_mv" 389 #ifndef CONFIG_SPL_BUILD 390 #define CONFIG_VID 391 #endif 392 #define CONFIG_VOL_MONITOR_IR36021_SET 393 #define CONFIG_VOL_MONITOR_IR36021_READ 394 /* The lowest and highest voltage allowed for T208xRDB */ 395 #define VDD_MV_MIN 819 396 #define VDD_MV_MAX 1212 397 398 /* 399 * RapidIO 400 */ 401 #define CONFIG_SYS_SRIO1_MEM_VIRT 0xa0000000 402 #define CONFIG_SYS_SRIO1_MEM_PHYS 0xc20000000ull 403 #define CONFIG_SYS_SRIO1_MEM_SIZE 0x10000000 /* 256M */ 404 #define CONFIG_SYS_SRIO2_MEM_VIRT 0xb0000000 405 #define CONFIG_SYS_SRIO2_MEM_PHYS 0xc30000000ull 406 #define CONFIG_SYS_SRIO2_MEM_SIZE 0x10000000 /* 256M */ 407 /* 408 * for slave u-boot IMAGE instored in master memory space, 409 * PHYS must be aligned based on the SIZE 410 */ 411 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull 412 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull 413 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x100000 /* 1M */ 414 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull 415 /* 416 * for slave UCODE and ENV instored in master memory space, 417 * PHYS must be aligned based on the SIZE 418 */ 419 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull 420 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull 421 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */ 422 423 /* slave core release by master*/ 424 #define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4 425 #define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */ 426 427 /* 428 * SRIO_PCIE_BOOT - SLAVE 429 */ 430 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE 431 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000 432 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \ 433 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR) 434 #endif 435 436 /* 437 * eSPI - Enhanced SPI 438 */ 439 #ifdef CONFIG_SPI_FLASH 440 #define CONFIG_SPI_FLASH_BAR 441 #define CONFIG_SF_DEFAULT_SPEED 10000000 442 #define CONFIG_SF_DEFAULT_MODE 0 443 #endif 444 445 /* 446 * General PCI 447 * Memory space is mapped 1-1, but I/O space must start from 0. 448 */ 449 #define CONFIG_PCIE1 /* PCIE controller 1 */ 450 #define CONFIG_PCIE2 /* PCIE controller 2 */ 451 #define CONFIG_PCIE3 /* PCIE controller 3 */ 452 #define CONFIG_PCIE4 /* PCIE controller 4 */ 453 #define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ 454 #define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ 455 /* controller 1, direct to uli, tgtid 3, Base address 20000 */ 456 #define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 457 #define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 458 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull 459 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ 460 #define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000 461 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 462 #define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull 463 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ 464 465 /* controller 2, Slot 2, tgtid 2, Base address 201000 */ 466 #define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 467 #define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000 468 #define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull 469 #define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */ 470 #define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000 471 #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 472 #define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull 473 #define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ 474 475 /* controller 3, Slot 1, tgtid 1, Base address 202000 */ 476 #define CONFIG_SYS_PCIE3_MEM_VIRT 0xb0000000 477 #define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000 478 #define CONFIG_SYS_PCIE3_MEM_PHYS 0xc30000000ull 479 #define CONFIG_SYS_PCIE3_MEM_SIZE 0x10000000 /* 256M */ 480 #define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000 481 #define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 482 #define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull 483 #define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */ 484 485 /* controller 4, Base address 203000 */ 486 #define CONFIG_SYS_PCIE4_MEM_VIRT 0xc0000000 487 #define CONFIG_SYS_PCIE4_MEM_BUS 0xe0000000 488 #define CONFIG_SYS_PCIE4_MEM_PHYS 0xc40000000ull 489 #define CONFIG_SYS_PCIE4_MEM_SIZE 0x10000000 /* 256M */ 490 #define CONFIG_SYS_PCIE4_IO_BUS 0x00000000 491 #define CONFIG_SYS_PCIE4_IO_PHYS 0xff8030000ull 492 #define CONFIG_SYS_PCIE4_IO_SIZE 0x00010000 /* 64k */ 493 494 #ifdef CONFIG_PCI 495 #define CONFIG_PCI_INDIRECT_BRIDGE 496 #define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata LSZ ADD */ 497 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 498 #endif 499 500 /* Qman/Bman */ 501 #ifndef CONFIG_NOBQFMAN 502 #define CONFIG_SYS_BMAN_NUM_PORTALS 18 503 #define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000 504 #define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull 505 #define CONFIG_SYS_BMAN_MEM_SIZE 0x02000000 506 #define CONFIG_SYS_BMAN_SP_CENA_SIZE 0x4000 507 #define CONFIG_SYS_BMAN_SP_CINH_SIZE 0x1000 508 #define CONFIG_SYS_BMAN_CENA_BASE CONFIG_SYS_BMAN_MEM_BASE 509 #define CONFIG_SYS_BMAN_CENA_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) 510 #define CONFIG_SYS_BMAN_CINH_BASE (CONFIG_SYS_BMAN_MEM_BASE + \ 511 CONFIG_SYS_BMAN_CENA_SIZE) 512 #define CONFIG_SYS_BMAN_CINH_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) 513 #define CONFIG_SYS_BMAN_SWP_ISDR_REG 0xE08 514 #define CONFIG_SYS_QMAN_NUM_PORTALS 18 515 #define CONFIG_SYS_QMAN_MEM_BASE 0xf6000000 516 #define CONFIG_SYS_QMAN_MEM_PHYS 0xff6000000ull 517 #define CONFIG_SYS_QMAN_MEM_SIZE 0x02000000 518 #define CONFIG_SYS_QMAN_SP_CENA_SIZE 0x4000 519 #define CONFIG_SYS_QMAN_SP_CINH_SIZE 0x1000 520 #define CONFIG_SYS_QMAN_CENA_BASE CONFIG_SYS_QMAN_MEM_BASE 521 #define CONFIG_SYS_QMAN_CENA_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) 522 #define CONFIG_SYS_QMAN_CINH_BASE (CONFIG_SYS_QMAN_MEM_BASE + \ 523 CONFIG_SYS_QMAN_CENA_SIZE) 524 #define CONFIG_SYS_QMAN_CINH_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) 525 #define CONFIG_SYS_QMAN_SWP_ISDR_REG 0xE08 526 527 #define CONFIG_SYS_DPAA_FMAN 528 #define CONFIG_SYS_DPAA_PME 529 #define CONFIG_SYS_PMAN 530 #define CONFIG_SYS_DPAA_DCE 531 #define CONFIG_SYS_DPAA_RMAN /* RMan */ 532 #define CONFIG_SYS_INTERLAKEN 533 534 /* Default address of microcode for the Linux Fman driver */ 535 #if defined(CONFIG_SPIFLASH) 536 /* 537 * env is stored at 0x100000, sector size is 0x10000, ucode is stored after 538 * env, so we got 0x110000. 539 */ 540 #define CONFIG_SYS_QE_FW_IN_SPIFLASH 541 #define CONFIG_SYS_CORTINA_FW_IN_SPIFLASH 542 #define CONFIG_SYS_FMAN_FW_ADDR 0x110000 543 #define CONFIG_CORTINA_FW_ADDR 0x120000 544 545 #elif defined(CONFIG_SDCARD) 546 /* 547 * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is 548 * about 1MB (2048 blocks), Env is stored after the image, and the env size is 549 * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080. 550 */ 551 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC 552 #define CONFIG_SYS_CORTINA_FW_IN_MMC 553 #define CONFIG_SYS_FMAN_FW_ADDR (512 * 0x820) 554 #define CONFIG_CORTINA_FW_ADDR (512 * 0x8a0) 555 556 #elif defined(CONFIG_NAND) 557 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND 558 #define CONFIG_SYS_CORTINA_FW_IN_NAND 559 #define CONFIG_SYS_FMAN_FW_ADDR (3 * CONFIG_SYS_NAND_BLOCK_SIZE) 560 #define CONFIG_CORTINA_FW_ADDR (4 * CONFIG_SYS_NAND_BLOCK_SIZE) 561 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) 562 /* 563 * Slave has no ucode locally, it can fetch this from remote. When implementing 564 * in two corenet boards, slave's ucode could be stored in master's memory 565 * space, the address can be mapped from slave TLB->slave LAW-> 566 * slave SRIO or PCIE outbound window->master inbound window-> 567 * master LAW->the ucode address in master's memory space. 568 */ 569 #define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE 570 #define CONFIG_SYS_CORTINA_FW_IN_REMOTE 571 #define CONFIG_SYS_FMAN_FW_ADDR 0xFFE00000 572 #define CONFIG_CORTINA_FW_ADDR 0xFFE10000 573 #else 574 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR 575 #define CONFIG_SYS_CORTINA_FW_IN_NOR 576 #define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000 577 #define CONFIG_CORTINA_FW_ADDR 0xEFE00000 578 #endif 579 #define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 580 #define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) 581 #endif /* CONFIG_NOBQFMAN */ 582 583 #ifdef CONFIG_SYS_DPAA_FMAN 584 #define CONFIG_FMAN_ENET 585 #define CONFIG_PHYLIB_10G 586 #define CONFIG_PHY_AQUANTIA 587 #define CONFIG_PHY_CORTINA 588 #define CONFIG_PHY_REALTEK 589 #define CONFIG_CORTINA_FW_LENGTH 0x40000 590 #define RGMII_PHY1_ADDR 0x01 /* RealTek RTL8211E */ 591 #define RGMII_PHY2_ADDR 0x02 592 #define CORTINA_PHY_ADDR1 0x0c /* Cortina CS4315 */ 593 #define CORTINA_PHY_ADDR2 0x0d 594 #define FM1_10GEC3_PHY_ADDR 0x00 /* Aquantia AQ1202 10G Base-T */ 595 #define FM1_10GEC4_PHY_ADDR 0x01 596 #endif 597 598 #ifdef CONFIG_FMAN_ENET 599 #define CONFIG_ETHPRIME "FM1@DTSEC3" 600 #endif 601 602 /* 603 * SATA 604 */ 605 #ifdef CONFIG_FSL_SATA_V2 606 #define CONFIG_SYS_SATA_MAX_DEVICE 2 607 #define CONFIG_SATA1 608 #define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR 609 #define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA 610 #define CONFIG_SATA2 611 #define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR 612 #define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA 613 #define CONFIG_LBA48 614 #endif 615 616 /* 617 * USB 618 */ 619 #ifdef CONFIG_USB_EHCI_HCD 620 #define CONFIG_USB_EHCI_FSL 621 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET 622 #define CONFIG_HAS_FSL_DR_USB 623 #endif 624 625 /* 626 * SDHC 627 */ 628 #ifdef CONFIG_MMC 629 #define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR 630 #define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT 631 #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33 632 #endif 633 634 /* 635 * Dynamic MTD Partition support with mtdparts 636 */ 637 638 /* 639 * Environment 640 */ 641 642 /* 643 * Miscellaneous configurable options 644 */ 645 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 646 647 /* 648 * For booting Linux, the board info and command line data 649 * have to be in the first 64 MB of memory, since this is 650 * the maximum mapped by the Linux kernel during initialization. 651 */ 652 #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial map for Linux*/ 653 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 654 655 #ifdef CONFIG_CMD_KGDB 656 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ 657 #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ 658 #endif 659 660 /* 661 * Environment Configuration 662 */ 663 #define CONFIG_ROOTPATH "/opt/nfsroot" 664 #define CONFIG_BOOTFILE "uImage" 665 #define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server */ 666 667 /* default location for tftp and bootm */ 668 #define CONFIG_LOADADDR 1000000 669 #define __USB_PHY_TYPE utmi 670 671 #define CONFIG_EXTRA_ENV_SETTINGS \ 672 "hwconfig=fsl_ddr:" \ 673 "ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) "," \ 674 "bank_intlv=auto;" \ 675 "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\ 676 "netdev=eth0\0" \ 677 "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ 678 "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \ 679 "tftpflash=tftpboot $loadaddr $uboot && " \ 680 "protect off $ubootaddr +$filesize && " \ 681 "erase $ubootaddr +$filesize && " \ 682 "cp.b $loadaddr $ubootaddr $filesize && " \ 683 "protect on $ubootaddr +$filesize && " \ 684 "cmp.b $loadaddr $ubootaddr $filesize\0" \ 685 "consoledev=ttyS0\0" \ 686 "ramdiskaddr=2000000\0" \ 687 "ramdiskfile=t2080rdb/ramdisk.uboot\0" \ 688 "fdtaddr=1e00000\0" \ 689 "fdtfile=t2080rdb/t2080rdb.dtb\0" \ 690 "bdev=sda3\0" 691 692 /* 693 * For emulation this causes u-boot to jump to the start of the 694 * proof point app code automatically 695 */ 696 #define CONFIG_PROOF_POINTS \ 697 "setenv bootargs root=/dev/$bdev rw " \ 698 "console=$consoledev,$baudrate $othbootargs;" \ 699 "cpu 1 release 0x29000000 - - -;" \ 700 "cpu 2 release 0x29000000 - - -;" \ 701 "cpu 3 release 0x29000000 - - -;" \ 702 "cpu 4 release 0x29000000 - - -;" \ 703 "cpu 5 release 0x29000000 - - -;" \ 704 "cpu 6 release 0x29000000 - - -;" \ 705 "cpu 7 release 0x29000000 - - -;" \ 706 "go 0x29000000" 707 708 #define CONFIG_HVBOOT \ 709 "setenv bootargs config-addr=0x60000000; " \ 710 "bootm 0x01000000 - 0x00f00000" 711 712 #define CONFIG_ALU \ 713 "setenv bootargs root=/dev/$bdev rw " \ 714 "console=$consoledev,$baudrate $othbootargs;" \ 715 "cpu 1 release 0x01000000 - - -;" \ 716 "cpu 2 release 0x01000000 - - -;" \ 717 "cpu 3 release 0x01000000 - - -;" \ 718 "cpu 4 release 0x01000000 - - -;" \ 719 "cpu 5 release 0x01000000 - - -;" \ 720 "cpu 6 release 0x01000000 - - -;" \ 721 "cpu 7 release 0x01000000 - - -;" \ 722 "go 0x01000000" 723 724 #define CONFIG_LINUX \ 725 "setenv bootargs root=/dev/ram rw " \ 726 "console=$consoledev,$baudrate $othbootargs;" \ 727 "setenv ramdiskaddr 0x02000000;" \ 728 "setenv fdtaddr 0x00c00000;" \ 729 "setenv loadaddr 0x1000000;" \ 730 "bootm $loadaddr $ramdiskaddr $fdtaddr" 731 732 #define CONFIG_HDBOOT \ 733 "setenv bootargs root=/dev/$bdev rw " \ 734 "console=$consoledev,$baudrate $othbootargs;" \ 735 "tftp $loadaddr $bootfile;" \ 736 "tftp $fdtaddr $fdtfile;" \ 737 "bootm $loadaddr - $fdtaddr" 738 739 #define CONFIG_NFSBOOTCOMMAND \ 740 "setenv bootargs root=/dev/nfs rw " \ 741 "nfsroot=$serverip:$rootpath " \ 742 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 743 "console=$consoledev,$baudrate $othbootargs;" \ 744 "tftp $loadaddr $bootfile;" \ 745 "tftp $fdtaddr $fdtfile;" \ 746 "bootm $loadaddr - $fdtaddr" 747 748 #define CONFIG_RAMBOOTCOMMAND \ 749 "setenv bootargs root=/dev/ram rw " \ 750 "console=$consoledev,$baudrate $othbootargs;" \ 751 "tftp $ramdiskaddr $ramdiskfile;" \ 752 "tftp $loadaddr $bootfile;" \ 753 "tftp $fdtaddr $fdtfile;" \ 754 "bootm $loadaddr $ramdiskaddr $fdtaddr" 755 756 #define CONFIG_BOOTCOMMAND CONFIG_LINUX 757 758 #include <asm/fsl_secure_boot.h> 759 760 #endif /* __T2080RDB_H */ 761