1 /* 2 * Copyright 2014 Freescale Semiconductor, Inc. 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 /* 8 * T2080 RDB/PCIe board configuration file 9 */ 10 11 #ifndef __T2080RDB_H 12 #define __T2080RDB_H 13 14 #define CONFIG_DISPLAY_BOARDINFO 15 #define CONFIG_T2080RDB 16 #define CONFIG_ICS307_REFCLK_HZ 25000000 /* ICS307 ref clk freq */ 17 #define CONFIG_MMC 18 #define CONFIG_USB_EHCI 19 #define CONFIG_FSL_SATA_V2 20 21 /* High Level Configuration Options */ 22 #define CONFIG_PHYS_64BIT 23 #define CONFIG_BOOKE 24 #define CONFIG_E500 /* BOOKE e500 family */ 25 #define CONFIG_E500MC /* BOOKE e500mc family */ 26 #define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */ 27 #define CONFIG_MP /* support multiple processors */ 28 #define CONFIG_ENABLE_36BIT_PHYS 29 30 #ifdef CONFIG_PHYS_64BIT 31 #define CONFIG_ADDR_MAP 1 32 #define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */ 33 #endif 34 35 #define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */ 36 #define CONFIG_SYS_NUM_CPC CONFIG_NUM_DDR_CONTROLLERS 37 #define CONFIG_FSL_IFC /* Enable IFC Support */ 38 #define CONFIG_FSL_CAAM /* Enable SEC/CAAM */ 39 #define CONFIG_FSL_LAW /* Use common FSL init code */ 40 #define CONFIG_ENV_OVERWRITE 41 42 #ifdef CONFIG_RAMBOOT_PBL 43 #define CONFIG_SYS_FSL_PBL_PBI board/freescale/t208xrdb/t2080_pbi.cfg 44 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xrdb/t2080_rcw.cfg 45 46 #define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT 47 #define CONFIG_SPL_ENV_SUPPORT 48 #define CONFIG_SPL_SERIAL_SUPPORT 49 #define CONFIG_SPL_FLUSH_IMAGE 50 #define CONFIG_SPL_TARGET "u-boot-with-spl.bin" 51 #define CONFIG_SPL_LIBGENERIC_SUPPORT 52 #define CONFIG_SPL_LIBCOMMON_SUPPORT 53 #define CONFIG_SPL_I2C_SUPPORT 54 #define CONFIG_SPL_DRIVERS_MISC_SUPPORT 55 #define CONFIG_FSL_LAW /* Use common FSL init code */ 56 #define CONFIG_SYS_TEXT_BASE 0x00201000 57 #define CONFIG_SPL_TEXT_BASE 0xFFFD8000 58 #define CONFIG_SPL_PAD_TO 0x40000 59 #define CONFIG_SPL_MAX_SIZE 0x28000 60 #define RESET_VECTOR_OFFSET 0x27FFC 61 #define BOOT_PAGE_OFFSET 0x27000 62 #ifdef CONFIG_SPL_BUILD 63 #define CONFIG_SPL_SKIP_RELOCATE 64 #define CONFIG_SPL_COMMON_INIT_DDR 65 #define CONFIG_SYS_CCSR_DO_NOT_RELOCATE 66 #define CONFIG_SYS_NO_FLASH 67 #endif 68 69 #ifdef CONFIG_NAND 70 #define CONFIG_SPL_NAND_SUPPORT 71 #define CONFIG_SYS_NAND_U_BOOT_SIZE (768 << 10) 72 #define CONFIG_SYS_NAND_U_BOOT_DST 0x00200000 73 #define CONFIG_SYS_NAND_U_BOOT_START 0x00200000 74 #define CONFIG_SYS_NAND_U_BOOT_OFFS (256 << 10) 75 #define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot-nand.lds" 76 #define CONFIG_SPL_NAND_BOOT 77 #endif 78 79 #ifdef CONFIG_SPIFLASH 80 #define CONFIG_RESET_VECTOR_ADDRESS 0x200FFC 81 #define CONFIG_SPL_SPI_SUPPORT 82 #define CONFIG_SPL_SPI_FLASH_SUPPORT 83 #define CONFIG_SPL_SPI_FLASH_MINIMAL 84 #define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE (768 << 10) 85 #define CONFIG_SYS_SPI_FLASH_U_BOOT_DST (0x00200000) 86 #define CONFIG_SYS_SPI_FLASH_U_BOOT_START (0x00200000) 87 #define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS (256 << 10) 88 #define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot.lds" 89 #ifndef CONFIG_SPL_BUILD 90 #define CONFIG_SYS_MPC85XX_NO_RESETVEC 91 #endif 92 #define CONFIG_SPL_SPI_BOOT 93 #endif 94 95 #ifdef CONFIG_SDCARD 96 #define CONFIG_RESET_VECTOR_ADDRESS 0x200FFC 97 #define CONFIG_SPL_MMC_SUPPORT 98 #define CONFIG_SPL_MMC_MINIMAL 99 #define CONFIG_SYS_MMC_U_BOOT_SIZE (768 << 10) 100 #define CONFIG_SYS_MMC_U_BOOT_DST (0x00200000) 101 #define CONFIG_SYS_MMC_U_BOOT_START (0x00200000) 102 #define CONFIG_SYS_MMC_U_BOOT_OFFS (260 << 10) 103 #define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot.lds" 104 #ifndef CONFIG_SPL_BUILD 105 #define CONFIG_SYS_MPC85XX_NO_RESETVEC 106 #endif 107 #define CONFIG_SPL_MMC_BOOT 108 #endif 109 110 #endif /* CONFIG_RAMBOOT_PBL */ 111 112 #define CONFIG_SRIO_PCIE_BOOT_MASTER 113 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE 114 /* Set 1M boot space */ 115 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000) 116 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \ 117 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR) 118 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc 119 #define CONFIG_SYS_NO_FLASH 120 #endif 121 122 #ifndef CONFIG_SYS_TEXT_BASE 123 #define CONFIG_SYS_TEXT_BASE 0xeff40000 124 #endif 125 126 #ifndef CONFIG_RESET_VECTOR_ADDRESS 127 #define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc 128 #endif 129 130 /* 131 * These can be toggled for performance analysis, otherwise use default. 132 */ 133 #define CONFIG_SYS_CACHE_STASHING 134 #define CONFIG_BTB /* toggle branch predition */ 135 #define CONFIG_DDR_ECC 136 #ifdef CONFIG_DDR_ECC 137 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER 138 #define CONFIG_MEM_INIT_VALUE 0xdeadbeef 139 #endif 140 141 #define CONFIG_CMD_MEMTEST 142 #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ 143 #define CONFIG_SYS_MEMTEST_END 0x00400000 144 #define CONFIG_SYS_ALT_MEMTEST 145 146 #ifndef CONFIG_SYS_NO_FLASH 147 #define CONFIG_FLASH_CFI_DRIVER 148 #define CONFIG_SYS_FLASH_CFI 149 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 150 #endif 151 152 #if defined(CONFIG_SPIFLASH) 153 #define CONFIG_SYS_EXTRA_ENV_RELOC 154 #define CONFIG_ENV_IS_IN_SPI_FLASH 155 #define CONFIG_ENV_SPI_BUS 0 156 #define CONFIG_ENV_SPI_CS 0 157 #define CONFIG_ENV_SPI_MAX_HZ 10000000 158 #define CONFIG_ENV_SPI_MODE 0 159 #define CONFIG_ENV_SIZE 0x2000 /* 8KB */ 160 #define CONFIG_ENV_OFFSET 0x100000 /* 1MB */ 161 #define CONFIG_ENV_SECT_SIZE 0x10000 162 #elif defined(CONFIG_SDCARD) 163 #define CONFIG_SYS_EXTRA_ENV_RELOC 164 #define CONFIG_ENV_IS_IN_MMC 165 #define CONFIG_SYS_MMC_ENV_DEV 0 166 #define CONFIG_ENV_SIZE 0x2000 167 #define CONFIG_ENV_OFFSET (512 * 0x800) 168 #elif defined(CONFIG_NAND) 169 #define CONFIG_SYS_EXTRA_ENV_RELOC 170 #define CONFIG_ENV_IS_IN_NAND 171 #define CONFIG_ENV_SIZE 0x2000 172 #define CONFIG_ENV_OFFSET (2 * CONFIG_SYS_NAND_BLOCK_SIZE) 173 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) 174 #define CONFIG_ENV_IS_IN_REMOTE 175 #define CONFIG_ENV_ADDR 0xffe20000 176 #define CONFIG_ENV_SIZE 0x2000 177 #elif defined(CONFIG_ENV_IS_NOWHERE) 178 #define CONFIG_ENV_SIZE 0x2000 179 #else 180 #define CONFIG_ENV_IS_IN_FLASH 181 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) 182 #define CONFIG_ENV_SIZE 0x2000 183 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ 184 #endif 185 186 #ifndef __ASSEMBLY__ 187 unsigned long get_board_sys_clk(void); 188 unsigned long get_board_ddr_clk(void); 189 #endif 190 191 #define CONFIG_SYS_CLK_FREQ 66660000 192 #define CONFIG_DDR_CLK_FREQ 133330000 193 194 /* 195 * Config the L3 Cache as L3 SRAM 196 */ 197 #define CONFIG_SYS_INIT_L3_ADDR 0xFFFC0000 198 #define CONFIG_SYS_L3_SIZE (512 << 10) 199 #define CONFIG_SPL_GD_ADDR (CONFIG_SYS_INIT_L3_ADDR + 32 * 1024) 200 #ifdef CONFIG_RAMBOOT_PBL 201 #define CONFIG_ENV_ADDR (CONFIG_SPL_GD_ADDR + 4 * 1024) 202 #endif 203 #define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SPL_GD_ADDR + 12 * 1024) 204 #define CONFIG_SPL_RELOC_MALLOC_SIZE (50 << 10) 205 #define CONFIG_SPL_RELOC_STACK (CONFIG_SPL_GD_ADDR + 64 * 1024) 206 #define CONFIG_SPL_RELOC_STACK_SIZE (22 << 10) 207 208 #define CONFIG_SYS_DCSRBAR 0xf0000000 209 #define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull 210 211 /* EEPROM */ 212 #define CONFIG_ID_EEPROM 213 #define CONFIG_SYS_I2C_EEPROM_NXID 214 #define CONFIG_SYS_EEPROM_BUS_NUM 0 215 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 216 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 217 218 /* 219 * DDR Setup 220 */ 221 #define CONFIG_VERY_BIG_RAM 222 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 223 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 224 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 225 #define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR) 226 #define CONFIG_DDR_SPD 227 #define CONFIG_SYS_FSL_DDR3 228 #undef CONFIG_FSL_DDR_INTERACTIVE 229 #define CONFIG_SYS_SPD_BUS_NUM 0 230 #define CONFIG_SYS_SDRAM_SIZE 2048 /* for fixed parameter use */ 231 #define SPD_EEPROM_ADDRESS1 0x51 232 #define SPD_EEPROM_ADDRESS2 0x52 233 #define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1 234 #define CTRL_INTLV_PREFERED cacheline 235 236 /* 237 * IFC Definitions 238 */ 239 #define CONFIG_SYS_FLASH_BASE 0xe8000000 240 #define CONFIG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CONFIG_SYS_FLASH_BASE) 241 #define CONFIG_SYS_NOR0_CSPR_EXT (0xf) 242 #define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \ 243 CSPR_PORT_SIZE_16 | \ 244 CSPR_MSEL_NOR | \ 245 CSPR_V) 246 #define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024) 247 248 /* NOR Flash Timing Params */ 249 #define CONFIG_SYS_NOR_CSOR CSOR_NAND_TRHZ_80 250 251 #define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \ 252 FTIM0_NOR_TEADC(0x5) | \ 253 FTIM0_NOR_TEAHC(0x5)) 254 #define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \ 255 FTIM1_NOR_TRAD_NOR(0x1A) |\ 256 FTIM1_NOR_TSEQRAD_NOR(0x13)) 257 #define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \ 258 FTIM2_NOR_TCH(0x4) | \ 259 FTIM2_NOR_TWPH(0x0E) | \ 260 FTIM2_NOR_TWP(0x1c)) 261 #define CONFIG_SYS_NOR_FTIM3 0x0 262 263 #define CONFIG_SYS_FLASH_QUIET_TEST 264 #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ 265 266 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 267 #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ 268 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 269 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 270 #define CONFIG_SYS_FLASH_EMPTY_INFO 271 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS } 272 273 /* CPLD on IFC */ 274 #define CONFIG_SYS_CPLD_BASE 0xffdf0000 275 #define CONFIG_SYS_CPLD_BASE_PHYS (0xf00000000ull | CONFIG_SYS_CPLD_BASE) 276 #define CONFIG_SYS_CSPR2_EXT (0xf) 277 #define CONFIG_SYS_CSPR2 (CSPR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE) \ 278 | CSPR_PORT_SIZE_8 \ 279 | CSPR_MSEL_GPCM \ 280 | CSPR_V) 281 #define CONFIG_SYS_AMASK2 IFC_AMASK(64*1024) 282 #define CONFIG_SYS_CSOR2 0x0 283 284 /* CPLD Timing parameters for IFC CS2 */ 285 #define CONFIG_SYS_CS2_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \ 286 FTIM0_GPCM_TEADC(0x0e) | \ 287 FTIM0_GPCM_TEAHC(0x0e)) 288 #define CONFIG_SYS_CS2_FTIM1 (FTIM1_GPCM_TACO(0x0e) | \ 289 FTIM1_GPCM_TRAD(0x1f)) 290 #define CONFIG_SYS_CS2_FTIM2 (FTIM2_GPCM_TCS(0x0e) | \ 291 FTIM2_GPCM_TCH(0x8) | \ 292 FTIM2_GPCM_TWP(0x1f)) 293 #define CONFIG_SYS_CS2_FTIM3 0x0 294 295 /* NAND Flash on IFC */ 296 #define CONFIG_NAND_FSL_IFC 297 #define CONFIG_SYS_NAND_BASE 0xff800000 298 #define CONFIG_SYS_NAND_BASE_PHYS (0xf00000000ull | CONFIG_SYS_NAND_BASE) 299 300 #define CONFIG_SYS_NAND_CSPR_EXT (0xf) 301 #define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ 302 | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \ 303 | CSPR_MSEL_NAND /* MSEL = NAND */ \ 304 | CSPR_V) 305 #define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024) 306 307 #define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \ 308 | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \ 309 | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \ 310 | CSOR_NAND_RAL_3 /* RAL = 2Byes */ \ 311 | CSOR_NAND_PGS_2K /* Page Size = 2K */\ 312 | CSOR_NAND_SPRZ_64 /* Spare size = 64 */\ 313 | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/ 314 315 #define CONFIG_SYS_NAND_ONFI_DETECTION 316 317 /* ONFI NAND Flash mode0 Timing Params */ 318 #define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \ 319 FTIM0_NAND_TWP(0x18) | \ 320 FTIM0_NAND_TWCHT(0x07) | \ 321 FTIM0_NAND_TWH(0x0a)) 322 #define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \ 323 FTIM1_NAND_TWBE(0x39) | \ 324 FTIM1_NAND_TRR(0x0e) | \ 325 FTIM1_NAND_TRP(0x18)) 326 #define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \ 327 FTIM2_NAND_TREH(0x0a) | \ 328 FTIM2_NAND_TWHRE(0x1e)) 329 #define CONFIG_SYS_NAND_FTIM3 0x0 330 331 #define CONFIG_SYS_NAND_DDR_LAW 11 332 #define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } 333 #define CONFIG_SYS_MAX_NAND_DEVICE 1 334 #define CONFIG_CMD_NAND 335 #define CONFIG_SYS_NAND_BLOCK_SIZE (512 * 1024) 336 337 #if defined(CONFIG_NAND) 338 #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT 339 #define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR 340 #define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK 341 #define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR 342 #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0 343 #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1 344 #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2 345 #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3 346 #define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR0_CSPR_EXT 347 #define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR0_CSPR 348 #define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK 349 #define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR 350 #define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0 351 #define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1 352 #define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2 353 #define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3 354 #else 355 #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT 356 #define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR 357 #define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK 358 #define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR 359 #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0 360 #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1 361 #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2 362 #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3 363 #define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NAND_CSPR_EXT 364 #define CONFIG_SYS_CSPR1 CONFIG_SYS_NAND_CSPR 365 #define CONFIG_SYS_AMASK1 CONFIG_SYS_NAND_AMASK 366 #define CONFIG_SYS_CSOR1 CONFIG_SYS_NAND_CSOR 367 #define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NAND_FTIM0 368 #define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NAND_FTIM1 369 #define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NAND_FTIM2 370 #define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NAND_FTIM3 371 #endif 372 373 #if defined(CONFIG_RAMBOOT_PBL) 374 #define CONFIG_SYS_RAMBOOT 375 #endif 376 377 #ifdef CONFIG_SPL_BUILD 378 #define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE 379 #else 380 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 381 #endif 382 383 #define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */ 384 #define CONFIG_MISC_INIT_R 385 #define CONFIG_HWCONFIG 386 387 /* define to use L1 as initial stack */ 388 #define CONFIG_L1_INIT_RAM 389 #define CONFIG_SYS_INIT_RAM_LOCK 390 #define CONFIG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */ 391 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf 392 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW 0xfe03c000 393 /* The assembler doesn't like typecast */ 394 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \ 395 ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \ 396 CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW) 397 #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 398 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ 399 GENERATED_GBL_DATA_SIZE) 400 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 401 #define CONFIG_SYS_MONITOR_LEN (768 * 1024) 402 #define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024) 403 404 /* 405 * Serial Port 406 */ 407 #define CONFIG_CONS_INDEX 1 408 #define CONFIG_SYS_NS16550_SERIAL 409 #define CONFIG_SYS_NS16550_REG_SIZE 1 410 #define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2) 411 #define CONFIG_SYS_BAUDRATE_TABLE \ 412 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} 413 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500) 414 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600) 415 #define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500) 416 #define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600) 417 418 /* Use the HUSH parser */ 419 #define CONFIG_SYS_HUSH_PARSER 420 #define CONFIG_SYS_PROMPT_HUSH_PS2 "> " 421 422 /* pass open firmware flat tree */ 423 #define CONFIG_OF_LIBFDT 424 #define CONFIG_OF_BOARD_SETUP 425 #define CONFIG_OF_STDOUT_VIA_ALIAS 426 427 /* new uImage format support */ 428 #define CONFIG_FIT 429 #define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ 430 431 /* 432 * I2C 433 */ 434 #define CONFIG_SYS_I2C 435 #define CONFIG_SYS_I2C_FSL 436 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 437 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F 438 #define CONFIG_SYS_FSL_I2C3_SLAVE 0x7F 439 #define CONFIG_SYS_FSL_I2C4_SLAVE 0x7F 440 #define CONFIG_SYS_FSL_I2C_OFFSET 0x118000 441 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100 442 #define CONFIG_SYS_FSL_I2C3_OFFSET 0x119000 443 #define CONFIG_SYS_FSL_I2C4_OFFSET 0x119100 444 #define CONFIG_SYS_FSL_I2C_SPEED 100000 445 #define CONFIG_SYS_FSL_I2C2_SPEED 100000 446 #define CONFIG_SYS_FSL_I2C3_SPEED 100000 447 #define CONFIG_SYS_FSL_I2C4_SPEED 100000 448 #define I2C_MUX_PCA_ADDR_PRI 0x77 /* I2C bus multiplexer,primary */ 449 #define I2C_MUX_PCA_ADDR_SEC1 0x75 /* I2C bus multiplexer,secondary 1 */ 450 #define I2C_MUX_PCA_ADDR_SEC2 0x76 /* I2C bus multiplexer,secondary 2 */ 451 #define I2C_MUX_CH_DEFAULT 0x8 452 453 #define I2C_MUX_CH_VOL_MONITOR 0xa 454 455 #define CONFIG_VID_FLS_ENV "t208xrdb_vdd_mv" 456 #ifndef CONFIG_SPL_BUILD 457 #define CONFIG_VID 458 #endif 459 #define CONFIG_VOL_MONITOR_IR36021_SET 460 #define CONFIG_VOL_MONITOR_IR36021_READ 461 /* The lowest and highest voltage allowed for T208xRDB */ 462 #define VDD_MV_MIN 819 463 #define VDD_MV_MAX 1212 464 465 /* 466 * RapidIO 467 */ 468 #define CONFIG_SYS_SRIO1_MEM_VIRT 0xa0000000 469 #define CONFIG_SYS_SRIO1_MEM_PHYS 0xc20000000ull 470 #define CONFIG_SYS_SRIO1_MEM_SIZE 0x10000000 /* 256M */ 471 #define CONFIG_SYS_SRIO2_MEM_VIRT 0xb0000000 472 #define CONFIG_SYS_SRIO2_MEM_PHYS 0xc30000000ull 473 #define CONFIG_SYS_SRIO2_MEM_SIZE 0x10000000 /* 256M */ 474 /* 475 * for slave u-boot IMAGE instored in master memory space, 476 * PHYS must be aligned based on the SIZE 477 */ 478 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull 479 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull 480 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x100000 /* 1M */ 481 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull 482 /* 483 * for slave UCODE and ENV instored in master memory space, 484 * PHYS must be aligned based on the SIZE 485 */ 486 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull 487 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull 488 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */ 489 490 /* slave core release by master*/ 491 #define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4 492 #define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */ 493 494 /* 495 * SRIO_PCIE_BOOT - SLAVE 496 */ 497 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE 498 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000 499 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \ 500 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR) 501 #endif 502 503 /* 504 * eSPI - Enhanced SPI 505 */ 506 #ifdef CONFIG_SPI_FLASH 507 #define CONFIG_SPI_FLASH_BAR 508 #define CONFIG_CMD_SF 509 #define CONFIG_SF_DEFAULT_SPEED 10000000 510 #define CONFIG_SF_DEFAULT_MODE 0 511 #endif 512 513 /* 514 * General PCI 515 * Memory space is mapped 1-1, but I/O space must start from 0. 516 */ 517 #define CONFIG_PCI /* Enable PCI/PCIE */ 518 #define CONFIG_PCIE1 /* PCIE controler 1 */ 519 #define CONFIG_PCIE2 /* PCIE controler 2 */ 520 #define CONFIG_PCIE3 /* PCIE controler 3 */ 521 #define CONFIG_PCIE4 /* PCIE controler 4 */ 522 #define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ 523 #define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ 524 /* controller 1, direct to uli, tgtid 3, Base address 20000 */ 525 #define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 526 #define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 527 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull 528 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ 529 #define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000 530 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 531 #define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull 532 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ 533 534 /* controller 2, Slot 2, tgtid 2, Base address 201000 */ 535 #define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 536 #define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000 537 #define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull 538 #define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */ 539 #define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000 540 #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 541 #define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull 542 #define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ 543 544 /* controller 3, Slot 1, tgtid 1, Base address 202000 */ 545 #define CONFIG_SYS_PCIE3_MEM_VIRT 0xb0000000 546 #define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000 547 #define CONFIG_SYS_PCIE3_MEM_PHYS 0xc30000000ull 548 #define CONFIG_SYS_PCIE3_MEM_SIZE 0x10000000 /* 256M */ 549 #define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000 550 #define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 551 #define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull 552 #define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */ 553 554 /* controller 4, Base address 203000 */ 555 #define CONFIG_SYS_PCIE4_MEM_VIRT 0xc0000000 556 #define CONFIG_SYS_PCIE4_MEM_BUS 0xe0000000 557 #define CONFIG_SYS_PCIE4_MEM_PHYS 0xc40000000ull 558 #define CONFIG_SYS_PCIE4_MEM_SIZE 0x10000000 /* 256M */ 559 #define CONFIG_SYS_PCIE4_IO_BUS 0x00000000 560 #define CONFIG_SYS_PCIE4_IO_PHYS 0xff8030000ull 561 #define CONFIG_SYS_PCIE4_IO_SIZE 0x00010000 /* 64k */ 562 563 #ifdef CONFIG_PCI 564 #define CONFIG_PCI_INDIRECT_BRIDGE 565 #define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata LSZ ADD */ 566 #define CONFIG_PCI_PNP /* do pci plug-and-play */ 567 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 568 #define CONFIG_DOS_PARTITION 569 #endif 570 571 /* Qman/Bman */ 572 #ifndef CONFIG_NOBQFMAN 573 #define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */ 574 #define CONFIG_SYS_BMAN_NUM_PORTALS 18 575 #define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000 576 #define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull 577 #define CONFIG_SYS_BMAN_MEM_SIZE 0x02000000 578 #define CONFIG_SYS_BMAN_SP_CENA_SIZE 0x4000 579 #define CONFIG_SYS_BMAN_SP_CINH_SIZE 0x1000 580 #define CONFIG_SYS_BMAN_CENA_BASE CONFIG_SYS_BMAN_MEM_BASE 581 #define CONFIG_SYS_BMAN_CENA_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) 582 #define CONFIG_SYS_BMAN_CINH_BASE (CONFIG_SYS_BMAN_MEM_BASE + \ 583 CONFIG_SYS_BMAN_CENA_SIZE) 584 #define CONFIG_SYS_BMAN_CINH_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) 585 #define CONFIG_SYS_BMAN_SWP_ISDR_REG 0xE08 586 #define CONFIG_SYS_QMAN_NUM_PORTALS 18 587 #define CONFIG_SYS_QMAN_MEM_BASE 0xf6000000 588 #define CONFIG_SYS_QMAN_MEM_PHYS 0xff6000000ull 589 #define CONFIG_SYS_QMAN_MEM_SIZE 0x02000000 590 #define CONFIG_SYS_QMAN_SP_CENA_SIZE 0x4000 591 #define CONFIG_SYS_QMAN_SP_CINH_SIZE 0x1000 592 #define CONFIG_SYS_QMAN_CENA_BASE CONFIG_SYS_QMAN_MEM_BASE 593 #define CONFIG_SYS_QMAN_CENA_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) 594 #define CONFIG_SYS_QMAN_CINH_BASE (CONFIG_SYS_QMAN_MEM_BASE + \ 595 CONFIG_SYS_QMAN_CENA_SIZE) 596 #define CONFIG_SYS_QMAN_CINH_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) 597 #define CONFIG_SYS_QMAN_SWP_ISDR_REG 0xE08 598 599 #define CONFIG_SYS_DPAA_FMAN 600 #define CONFIG_SYS_DPAA_PME 601 #define CONFIG_SYS_PMAN 602 #define CONFIG_SYS_DPAA_DCE 603 #define CONFIG_SYS_DPAA_RMAN /* RMan */ 604 #define CONFIG_SYS_INTERLAKEN 605 606 /* Default address of microcode for the Linux Fman driver */ 607 #if defined(CONFIG_SPIFLASH) 608 /* 609 * env is stored at 0x100000, sector size is 0x10000, ucode is stored after 610 * env, so we got 0x110000. 611 */ 612 #define CONFIG_SYS_QE_FW_IN_SPIFLASH 613 #define CONFIG_SYS_CORTINA_FW_IN_SPIFLASH 614 #define CONFIG_SYS_FMAN_FW_ADDR 0x110000 615 #define CONFIG_CORTINA_FW_ADDR 0x120000 616 617 #elif defined(CONFIG_SDCARD) 618 /* 619 * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is 620 * about 1MB (2048 blocks), Env is stored after the image, and the env size is 621 * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080. 622 */ 623 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC 624 #define CONFIG_SYS_CORTINA_FW_IN_MMC 625 #define CONFIG_SYS_FMAN_FW_ADDR (512 * 0x820) 626 #define CONFIG_CORTINA_FW_ADDR (512 * 0x8a0) 627 628 #elif defined(CONFIG_NAND) 629 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND 630 #define CONFIG_SYS_CORTINA_FW_IN_NAND 631 #define CONFIG_SYS_FMAN_FW_ADDR (3 * CONFIG_SYS_NAND_BLOCK_SIZE) 632 #define CONFIG_CORTINA_FW_ADDR (4 * CONFIG_SYS_NAND_BLOCK_SIZE) 633 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) 634 /* 635 * Slave has no ucode locally, it can fetch this from remote. When implementing 636 * in two corenet boards, slave's ucode could be stored in master's memory 637 * space, the address can be mapped from slave TLB->slave LAW-> 638 * slave SRIO or PCIE outbound window->master inbound window-> 639 * master LAW->the ucode address in master's memory space. 640 */ 641 #define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE 642 #define CONFIG_SYS_CORTINA_FW_IN_REMOTE 643 #define CONFIG_SYS_FMAN_FW_ADDR 0xFFE00000 644 #define CONFIG_CORTINA_FW_ADDR 0xFFE10000 645 #else 646 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR 647 #define CONFIG_SYS_CORTINA_FW_IN_NOR 648 #define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000 649 #define CONFIG_CORTINA_FW_ADDR 0xEFE00000 650 #endif 651 #define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 652 #define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) 653 #endif /* CONFIG_NOBQFMAN */ 654 655 #ifdef CONFIG_SYS_DPAA_FMAN 656 #define CONFIG_FMAN_ENET 657 #define CONFIG_PHYLIB_10G 658 #define CONFIG_PHY_AQUANTIA 659 #define CONFIG_PHY_CORTINA 660 #define CONFIG_PHY_REALTEK 661 #define CONFIG_CORTINA_FW_LENGTH 0x40000 662 #define RGMII_PHY1_ADDR 0x01 /* RealTek RTL8211E */ 663 #define RGMII_PHY2_ADDR 0x02 664 #define CORTINA_PHY_ADDR1 0x0c /* Cortina CS4315 */ 665 #define CORTINA_PHY_ADDR2 0x0d 666 #define FM1_10GEC3_PHY_ADDR 0x00 /* Aquantia AQ1202 10G Base-T */ 667 #define FM1_10GEC4_PHY_ADDR 0x01 668 #endif 669 670 671 #ifdef CONFIG_FMAN_ENET 672 #define CONFIG_MII /* MII PHY management */ 673 #define CONFIG_ETHPRIME "FM1@DTSEC3" 674 #define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ 675 #endif 676 677 /* 678 * SATA 679 */ 680 #ifdef CONFIG_FSL_SATA_V2 681 #define CONFIG_LIBATA 682 #define CONFIG_FSL_SATA 683 #define CONFIG_SYS_SATA_MAX_DEVICE 2 684 #define CONFIG_SATA1 685 #define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR 686 #define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA 687 #define CONFIG_SATA2 688 #define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR 689 #define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA 690 #define CONFIG_LBA48 691 #define CONFIG_CMD_SATA 692 #define CONFIG_DOS_PARTITION 693 #define CONFIG_CMD_EXT2 694 #endif 695 696 /* 697 * USB 698 */ 699 #ifdef CONFIG_USB_EHCI 700 #define CONFIG_CMD_USB 701 #define CONFIG_USB_STORAGE 702 #define CONFIG_USB_EHCI_FSL 703 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET 704 #define CONFIG_CMD_EXT2 705 #define CONFIG_HAS_FSL_DR_USB 706 #endif 707 708 /* 709 * SDHC 710 */ 711 #ifdef CONFIG_MMC 712 #define CONFIG_CMD_MMC 713 #define CONFIG_FSL_ESDHC 714 #define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR 715 #define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT 716 #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33 717 #define CONFIG_GENERIC_MMC 718 #define CONFIG_CMD_EXT2 719 #define CONFIG_CMD_FAT 720 #define CONFIG_DOS_PARTITION 721 #endif 722 723 /* 724 * Dynamic MTD Partition support with mtdparts 725 */ 726 #ifndef CONFIG_SYS_NO_FLASH 727 #define CONFIG_MTD_DEVICE 728 #define CONFIG_MTD_PARTITIONS 729 #define CONFIG_CMD_MTDPARTS 730 #define CONFIG_FLASH_CFI_MTD 731 #define MTDIDS_DEFAULT "nor0=fe8000000.nor,nand0=fff800000.flash," \ 732 "spi0=spife110000.1" 733 #define MTDPARTS_DEFAULT "mtdparts=fe8000000.nor:1m(uboot),5m(kernel)," \ 734 "128k(dtb),96m(fs),-(user);fff800000.flash:1m(uboot)," \ 735 "5m(kernel),128k(dtb),96m(fs),-(user);spife110000.1:" \ 736 "1m(uboot),5m(kernel),128k(dtb),-(user)" 737 #endif 738 739 /* 740 * Environment 741 */ 742 743 /* 744 * Command line configuration. 745 */ 746 #define CONFIG_CMD_DHCP 747 #define CONFIG_CMD_ERRATA 748 #define CONFIG_CMD_MII 749 #define CONFIG_CMD_I2C 750 #define CONFIG_CMD_PING 751 #define CONFIG_CMD_REGINFO 752 753 #ifdef CONFIG_PCI 754 #define CONFIG_CMD_PCI 755 #endif 756 757 /* Hash command with SHA acceleration supported in hardware */ 758 #ifdef CONFIG_FSL_CAAM 759 #define CONFIG_CMD_HASH 760 #define CONFIG_SHA_HW_ACCEL 761 #endif 762 763 /* 764 * Miscellaneous configurable options 765 */ 766 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 767 #define CONFIG_CMDLINE_EDITING /* Command-line editing */ 768 #define CONFIG_AUTO_COMPLETE /* add autocompletion support */ 769 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 770 #ifdef CONFIG_CMD_KGDB 771 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 772 #else 773 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 774 #endif 775 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) 776 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 777 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */ 778 779 /* 780 * For booting Linux, the board info and command line data 781 * have to be in the first 64 MB of memory, since this is 782 * the maximum mapped by the Linux kernel during initialization. 783 */ 784 #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial map for Linux*/ 785 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 786 787 #ifdef CONFIG_CMD_KGDB 788 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ 789 #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ 790 #endif 791 792 /* 793 * Environment Configuration 794 */ 795 #define CONFIG_ROOTPATH "/opt/nfsroot" 796 #define CONFIG_BOOTFILE "uImage" 797 #define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server */ 798 799 /* default location for tftp and bootm */ 800 #define CONFIG_LOADADDR 1000000 801 #define CONFIG_BAUDRATE 115200 802 #define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ 803 #define __USB_PHY_TYPE utmi 804 805 #define CONFIG_EXTRA_ENV_SETTINGS \ 806 "hwconfig=fsl_ddr:" \ 807 "ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) "," \ 808 "bank_intlv=auto;" \ 809 "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\ 810 "netdev=eth0\0" \ 811 "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ 812 "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \ 813 "tftpflash=tftpboot $loadaddr $uboot && " \ 814 "protect off $ubootaddr +$filesize && " \ 815 "erase $ubootaddr +$filesize && " \ 816 "cp.b $loadaddr $ubootaddr $filesize && " \ 817 "protect on $ubootaddr +$filesize && " \ 818 "cmp.b $loadaddr $ubootaddr $filesize\0" \ 819 "consoledev=ttyS0\0" \ 820 "ramdiskaddr=2000000\0" \ 821 "ramdiskfile=t2080rdb/ramdisk.uboot\0" \ 822 "fdtaddr=c00000\0" \ 823 "fdtfile=t2080rdb/t2080rdb.dtb\0" \ 824 "bdev=sda3\0" 825 826 /* 827 * For emulation this causes u-boot to jump to the start of the 828 * proof point app code automatically 829 */ 830 #define CONFIG_PROOF_POINTS \ 831 "setenv bootargs root=/dev/$bdev rw " \ 832 "console=$consoledev,$baudrate $othbootargs;" \ 833 "cpu 1 release 0x29000000 - - -;" \ 834 "cpu 2 release 0x29000000 - - -;" \ 835 "cpu 3 release 0x29000000 - - -;" \ 836 "cpu 4 release 0x29000000 - - -;" \ 837 "cpu 5 release 0x29000000 - - -;" \ 838 "cpu 6 release 0x29000000 - - -;" \ 839 "cpu 7 release 0x29000000 - - -;" \ 840 "go 0x29000000" 841 842 #define CONFIG_HVBOOT \ 843 "setenv bootargs config-addr=0x60000000; " \ 844 "bootm 0x01000000 - 0x00f00000" 845 846 #define CONFIG_ALU \ 847 "setenv bootargs root=/dev/$bdev rw " \ 848 "console=$consoledev,$baudrate $othbootargs;" \ 849 "cpu 1 release 0x01000000 - - -;" \ 850 "cpu 2 release 0x01000000 - - -;" \ 851 "cpu 3 release 0x01000000 - - -;" \ 852 "cpu 4 release 0x01000000 - - -;" \ 853 "cpu 5 release 0x01000000 - - -;" \ 854 "cpu 6 release 0x01000000 - - -;" \ 855 "cpu 7 release 0x01000000 - - -;" \ 856 "go 0x01000000" 857 858 #define CONFIG_LINUX \ 859 "setenv bootargs root=/dev/ram rw " \ 860 "console=$consoledev,$baudrate $othbootargs;" \ 861 "setenv ramdiskaddr 0x02000000;" \ 862 "setenv fdtaddr 0x00c00000;" \ 863 "setenv loadaddr 0x1000000;" \ 864 "bootm $loadaddr $ramdiskaddr $fdtaddr" 865 866 #define CONFIG_HDBOOT \ 867 "setenv bootargs root=/dev/$bdev rw " \ 868 "console=$consoledev,$baudrate $othbootargs;" \ 869 "tftp $loadaddr $bootfile;" \ 870 "tftp $fdtaddr $fdtfile;" \ 871 "bootm $loadaddr - $fdtaddr" 872 873 #define CONFIG_NFSBOOTCOMMAND \ 874 "setenv bootargs root=/dev/nfs rw " \ 875 "nfsroot=$serverip:$rootpath " \ 876 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 877 "console=$consoledev,$baudrate $othbootargs;" \ 878 "tftp $loadaddr $bootfile;" \ 879 "tftp $fdtaddr $fdtfile;" \ 880 "bootm $loadaddr - $fdtaddr" 881 882 #define CONFIG_RAMBOOTCOMMAND \ 883 "setenv bootargs root=/dev/ram rw " \ 884 "console=$consoledev,$baudrate $othbootargs;" \ 885 "tftp $ramdiskaddr $ramdiskfile;" \ 886 "tftp $loadaddr $bootfile;" \ 887 "tftp $fdtaddr $fdtfile;" \ 888 "bootm $loadaddr $ramdiskaddr $fdtaddr" 889 890 #define CONFIG_BOOTCOMMAND CONFIG_LINUX 891 892 #ifdef CONFIG_SECURE_BOOT 893 #include <asm/fsl_secure_boot.h> 894 #define CONFIG_CMD_BLOB 895 #undef CONFIG_CMD_USB 896 #endif 897 898 #endif /* __T2080RDB_H */ 899