1 /* 2 * Copyright 2014 Freescale Semiconductor, Inc. 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 /* 8 * T2080 RDB/PCIe board configuration file 9 */ 10 11 #ifndef __T2080RDB_H 12 #define __T2080RDB_H 13 14 #define CONFIG_ICS307_REFCLK_HZ 25000000 /* ICS307 ref clk freq */ 15 #define CONFIG_FSL_SATA_V2 16 17 /* High Level Configuration Options */ 18 #define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */ 19 #define CONFIG_MP /* support multiple processors */ 20 #define CONFIG_ENABLE_36BIT_PHYS 21 22 #ifdef CONFIG_PHYS_64BIT 23 #define CONFIG_ADDR_MAP 1 24 #define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */ 25 #endif 26 27 #define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */ 28 #define CONFIG_SYS_NUM_CPC CONFIG_SYS_NUM_DDR_CTLRS 29 #define CONFIG_ENV_OVERWRITE 30 31 #ifdef CONFIG_RAMBOOT_PBL 32 #define CONFIG_SYS_FSL_PBL_PBI board/freescale/t208xrdb/t2080_pbi.cfg 33 34 #define CONFIG_SPL_FLUSH_IMAGE 35 #define CONFIG_SPL_TARGET "u-boot-with-spl.bin" 36 #define CONFIG_SYS_TEXT_BASE 0x00201000 37 #define CONFIG_SPL_TEXT_BASE 0xFFFD8000 38 #define CONFIG_SPL_PAD_TO 0x40000 39 #define CONFIG_SPL_MAX_SIZE 0x28000 40 #define RESET_VECTOR_OFFSET 0x27FFC 41 #define BOOT_PAGE_OFFSET 0x27000 42 #ifdef CONFIG_SPL_BUILD 43 #define CONFIG_SPL_SKIP_RELOCATE 44 #define CONFIG_SPL_COMMON_INIT_DDR 45 #define CONFIG_SYS_CCSR_DO_NOT_RELOCATE 46 #endif 47 48 #ifdef CONFIG_NAND 49 #define CONFIG_SYS_NAND_U_BOOT_SIZE (768 << 10) 50 #define CONFIG_SYS_NAND_U_BOOT_DST 0x00200000 51 #define CONFIG_SYS_NAND_U_BOOT_START 0x00200000 52 #define CONFIG_SYS_NAND_U_BOOT_OFFS (256 << 10) 53 #define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot-nand.lds" 54 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xrdb/t2080_nand_rcw.cfg 55 #define CONFIG_SPL_NAND_BOOT 56 #endif 57 58 #ifdef CONFIG_SPIFLASH 59 #define CONFIG_RESET_VECTOR_ADDRESS 0x200FFC 60 #define CONFIG_SPL_SPI_FLASH_MINIMAL 61 #define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE (768 << 10) 62 #define CONFIG_SYS_SPI_FLASH_U_BOOT_DST (0x00200000) 63 #define CONFIG_SYS_SPI_FLASH_U_BOOT_START (0x00200000) 64 #define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS (256 << 10) 65 #define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot.lds" 66 #ifndef CONFIG_SPL_BUILD 67 #define CONFIG_SYS_MPC85XX_NO_RESETVEC 68 #endif 69 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xrdb/t2080_spi_rcw.cfg 70 #define CONFIG_SPL_SPI_BOOT 71 #endif 72 73 #ifdef CONFIG_SDCARD 74 #define CONFIG_RESET_VECTOR_ADDRESS 0x200FFC 75 #define CONFIG_SPL_MMC_MINIMAL 76 #define CONFIG_SYS_MMC_U_BOOT_SIZE (768 << 10) 77 #define CONFIG_SYS_MMC_U_BOOT_DST (0x00200000) 78 #define CONFIG_SYS_MMC_U_BOOT_START (0x00200000) 79 #define CONFIG_SYS_MMC_U_BOOT_OFFS (260 << 10) 80 #define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot.lds" 81 #ifndef CONFIG_SPL_BUILD 82 #define CONFIG_SYS_MPC85XX_NO_RESETVEC 83 #endif 84 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xrdb/t2080_sd_rcw.cfg 85 #define CONFIG_SPL_MMC_BOOT 86 #endif 87 88 #endif /* CONFIG_RAMBOOT_PBL */ 89 90 #define CONFIG_SRIO_PCIE_BOOT_MASTER 91 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE 92 /* Set 1M boot space */ 93 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000) 94 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \ 95 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR) 96 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc 97 #endif 98 99 #ifndef CONFIG_SYS_TEXT_BASE 100 #define CONFIG_SYS_TEXT_BASE 0xeff40000 101 #endif 102 103 #ifndef CONFIG_RESET_VECTOR_ADDRESS 104 #define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc 105 #endif 106 107 /* 108 * These can be toggled for performance analysis, otherwise use default. 109 */ 110 #define CONFIG_SYS_CACHE_STASHING 111 #define CONFIG_BTB /* toggle branch predition */ 112 #define CONFIG_DDR_ECC 113 #ifdef CONFIG_DDR_ECC 114 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER 115 #define CONFIG_MEM_INIT_VALUE 0xdeadbeef 116 #endif 117 118 #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ 119 #define CONFIG_SYS_MEMTEST_END 0x00400000 120 #define CONFIG_SYS_ALT_MEMTEST 121 122 #ifdef CONFIG_MTD_NOR_FLASH 123 #define CONFIG_FLASH_CFI_DRIVER 124 #define CONFIG_SYS_FLASH_CFI 125 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 126 #endif 127 128 #if defined(CONFIG_SPIFLASH) 129 #define CONFIG_SYS_EXTRA_ENV_RELOC 130 #define CONFIG_ENV_SPI_BUS 0 131 #define CONFIG_ENV_SPI_CS 0 132 #define CONFIG_ENV_SPI_MAX_HZ 10000000 133 #define CONFIG_ENV_SPI_MODE 0 134 #define CONFIG_ENV_SIZE 0x2000 /* 8KB */ 135 #define CONFIG_ENV_OFFSET 0x100000 /* 1MB */ 136 #define CONFIG_ENV_SECT_SIZE 0x10000 137 #elif defined(CONFIG_SDCARD) 138 #define CONFIG_SYS_EXTRA_ENV_RELOC 139 #define CONFIG_SYS_MMC_ENV_DEV 0 140 #define CONFIG_ENV_SIZE 0x2000 141 #define CONFIG_ENV_OFFSET (512 * 0x800) 142 #elif defined(CONFIG_NAND) 143 #define CONFIG_SYS_EXTRA_ENV_RELOC 144 #define CONFIG_ENV_SIZE 0x2000 145 #define CONFIG_ENV_OFFSET (2 * CONFIG_SYS_NAND_BLOCK_SIZE) 146 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) 147 #define CONFIG_ENV_ADDR 0xffe20000 148 #define CONFIG_ENV_SIZE 0x2000 149 #elif defined(CONFIG_ENV_IS_NOWHERE) 150 #define CONFIG_ENV_SIZE 0x2000 151 #else 152 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) 153 #define CONFIG_ENV_SIZE 0x2000 154 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ 155 #endif 156 157 #ifndef __ASSEMBLY__ 158 unsigned long get_board_sys_clk(void); 159 unsigned long get_board_ddr_clk(void); 160 #endif 161 162 #define CONFIG_SYS_CLK_FREQ 66660000 163 #define CONFIG_DDR_CLK_FREQ 133330000 164 165 /* 166 * Config the L3 Cache as L3 SRAM 167 */ 168 #define CONFIG_SYS_INIT_L3_ADDR 0xFFFC0000 169 #define CONFIG_SYS_L3_SIZE (512 << 10) 170 #define CONFIG_SPL_GD_ADDR (CONFIG_SYS_INIT_L3_ADDR + 32 * 1024) 171 #ifdef CONFIG_RAMBOOT_PBL 172 #define CONFIG_ENV_ADDR (CONFIG_SPL_GD_ADDR + 4 * 1024) 173 #endif 174 #define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SPL_GD_ADDR + 12 * 1024) 175 #define CONFIG_SPL_RELOC_MALLOC_SIZE (50 << 10) 176 #define CONFIG_SPL_RELOC_STACK (CONFIG_SPL_GD_ADDR + 64 * 1024) 177 #define CONFIG_SPL_RELOC_STACK_SIZE (22 << 10) 178 179 #define CONFIG_SYS_DCSRBAR 0xf0000000 180 #define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull 181 182 /* EEPROM */ 183 #define CONFIG_ID_EEPROM 184 #define CONFIG_SYS_I2C_EEPROM_NXID 185 #define CONFIG_SYS_EEPROM_BUS_NUM 0 186 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 187 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 188 189 /* 190 * DDR Setup 191 */ 192 #define CONFIG_VERY_BIG_RAM 193 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 194 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 195 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 196 #define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR) 197 #define CONFIG_DDR_SPD 198 #undef CONFIG_FSL_DDR_INTERACTIVE 199 #define CONFIG_SYS_SPD_BUS_NUM 0 200 #define CONFIG_SYS_SDRAM_SIZE 2048 /* for fixed parameter use */ 201 #define SPD_EEPROM_ADDRESS1 0x51 202 #define SPD_EEPROM_ADDRESS2 0x52 203 #define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1 204 #define CTRL_INTLV_PREFERED cacheline 205 206 /* 207 * IFC Definitions 208 */ 209 #define CONFIG_SYS_FLASH_BASE 0xe8000000 210 #define CONFIG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CONFIG_SYS_FLASH_BASE) 211 #define CONFIG_SYS_NOR0_CSPR_EXT (0xf) 212 #define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \ 213 CSPR_PORT_SIZE_16 | \ 214 CSPR_MSEL_NOR | \ 215 CSPR_V) 216 #define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024) 217 218 /* NOR Flash Timing Params */ 219 #define CONFIG_SYS_NOR_CSOR CSOR_NAND_TRHZ_80 220 221 #define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \ 222 FTIM0_NOR_TEADC(0x5) | \ 223 FTIM0_NOR_TEAHC(0x5)) 224 #define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \ 225 FTIM1_NOR_TRAD_NOR(0x1A) |\ 226 FTIM1_NOR_TSEQRAD_NOR(0x13)) 227 #define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \ 228 FTIM2_NOR_TCH(0x4) | \ 229 FTIM2_NOR_TWPH(0x0E) | \ 230 FTIM2_NOR_TWP(0x1c)) 231 #define CONFIG_SYS_NOR_FTIM3 0x0 232 233 #define CONFIG_SYS_FLASH_QUIET_TEST 234 #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ 235 236 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 237 #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ 238 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 239 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 240 #define CONFIG_SYS_FLASH_EMPTY_INFO 241 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS } 242 243 /* CPLD on IFC */ 244 #define CONFIG_SYS_CPLD_BASE 0xffdf0000 245 #define CONFIG_SYS_CPLD_BASE_PHYS (0xf00000000ull | CONFIG_SYS_CPLD_BASE) 246 #define CONFIG_SYS_CSPR2_EXT (0xf) 247 #define CONFIG_SYS_CSPR2 (CSPR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE) \ 248 | CSPR_PORT_SIZE_8 \ 249 | CSPR_MSEL_GPCM \ 250 | CSPR_V) 251 #define CONFIG_SYS_AMASK2 IFC_AMASK(64*1024) 252 #define CONFIG_SYS_CSOR2 0x0 253 254 /* CPLD Timing parameters for IFC CS2 */ 255 #define CONFIG_SYS_CS2_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \ 256 FTIM0_GPCM_TEADC(0x0e) | \ 257 FTIM0_GPCM_TEAHC(0x0e)) 258 #define CONFIG_SYS_CS2_FTIM1 (FTIM1_GPCM_TACO(0x0e) | \ 259 FTIM1_GPCM_TRAD(0x1f)) 260 #define CONFIG_SYS_CS2_FTIM2 (FTIM2_GPCM_TCS(0x0e) | \ 261 FTIM2_GPCM_TCH(0x8) | \ 262 FTIM2_GPCM_TWP(0x1f)) 263 #define CONFIG_SYS_CS2_FTIM3 0x0 264 265 /* NAND Flash on IFC */ 266 #define CONFIG_NAND_FSL_IFC 267 #define CONFIG_SYS_NAND_BASE 0xff800000 268 #define CONFIG_SYS_NAND_BASE_PHYS (0xf00000000ull | CONFIG_SYS_NAND_BASE) 269 270 #define CONFIG_SYS_NAND_CSPR_EXT (0xf) 271 #define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ 272 | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \ 273 | CSPR_MSEL_NAND /* MSEL = NAND */ \ 274 | CSPR_V) 275 #define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024) 276 277 #define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \ 278 | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \ 279 | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \ 280 | CSOR_NAND_RAL_3 /* RAL = 2Byes */ \ 281 | CSOR_NAND_PGS_2K /* Page Size = 2K */\ 282 | CSOR_NAND_SPRZ_64 /* Spare size = 64 */\ 283 | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/ 284 285 #define CONFIG_SYS_NAND_ONFI_DETECTION 286 287 /* ONFI NAND Flash mode0 Timing Params */ 288 #define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \ 289 FTIM0_NAND_TWP(0x18) | \ 290 FTIM0_NAND_TWCHT(0x07) | \ 291 FTIM0_NAND_TWH(0x0a)) 292 #define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \ 293 FTIM1_NAND_TWBE(0x39) | \ 294 FTIM1_NAND_TRR(0x0e) | \ 295 FTIM1_NAND_TRP(0x18)) 296 #define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \ 297 FTIM2_NAND_TREH(0x0a) | \ 298 FTIM2_NAND_TWHRE(0x1e)) 299 #define CONFIG_SYS_NAND_FTIM3 0x0 300 301 #define CONFIG_SYS_NAND_DDR_LAW 11 302 #define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } 303 #define CONFIG_SYS_MAX_NAND_DEVICE 1 304 #define CONFIG_SYS_NAND_BLOCK_SIZE (512 * 1024) 305 306 #if defined(CONFIG_NAND) 307 #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT 308 #define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR 309 #define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK 310 #define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR 311 #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0 312 #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1 313 #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2 314 #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3 315 #define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR0_CSPR_EXT 316 #define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR0_CSPR 317 #define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK 318 #define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR 319 #define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0 320 #define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1 321 #define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2 322 #define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3 323 #else 324 #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT 325 #define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR 326 #define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK 327 #define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR 328 #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0 329 #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1 330 #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2 331 #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3 332 #define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NAND_CSPR_EXT 333 #define CONFIG_SYS_CSPR1 CONFIG_SYS_NAND_CSPR 334 #define CONFIG_SYS_AMASK1 CONFIG_SYS_NAND_AMASK 335 #define CONFIG_SYS_CSOR1 CONFIG_SYS_NAND_CSOR 336 #define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NAND_FTIM0 337 #define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NAND_FTIM1 338 #define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NAND_FTIM2 339 #define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NAND_FTIM3 340 #endif 341 342 #if defined(CONFIG_RAMBOOT_PBL) 343 #define CONFIG_SYS_RAMBOOT 344 #endif 345 346 #ifdef CONFIG_SPL_BUILD 347 #define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE 348 #else 349 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 350 #endif 351 352 #define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */ 353 #define CONFIG_MISC_INIT_R 354 #define CONFIG_HWCONFIG 355 356 /* define to use L1 as initial stack */ 357 #define CONFIG_L1_INIT_RAM 358 #define CONFIG_SYS_INIT_RAM_LOCK 359 #define CONFIG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */ 360 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf 361 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW 0xfe03c000 362 /* The assembler doesn't like typecast */ 363 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \ 364 ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \ 365 CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW) 366 #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 367 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ 368 GENERATED_GBL_DATA_SIZE) 369 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 370 #define CONFIG_SYS_MONITOR_LEN (768 * 1024) 371 #define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024) 372 373 /* 374 * Serial Port 375 */ 376 #define CONFIG_CONS_INDEX 1 377 #define CONFIG_SYS_NS16550_SERIAL 378 #define CONFIG_SYS_NS16550_REG_SIZE 1 379 #define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2) 380 #define CONFIG_SYS_BAUDRATE_TABLE \ 381 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} 382 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500) 383 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600) 384 #define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500) 385 #define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600) 386 387 /* 388 * I2C 389 */ 390 #define CONFIG_SYS_I2C 391 #define CONFIG_SYS_I2C_FSL 392 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 393 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F 394 #define CONFIG_SYS_FSL_I2C3_SLAVE 0x7F 395 #define CONFIG_SYS_FSL_I2C4_SLAVE 0x7F 396 #define CONFIG_SYS_FSL_I2C_OFFSET 0x118000 397 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100 398 #define CONFIG_SYS_FSL_I2C3_OFFSET 0x119000 399 #define CONFIG_SYS_FSL_I2C4_OFFSET 0x119100 400 #define CONFIG_SYS_FSL_I2C_SPEED 100000 401 #define CONFIG_SYS_FSL_I2C2_SPEED 100000 402 #define CONFIG_SYS_FSL_I2C3_SPEED 100000 403 #define CONFIG_SYS_FSL_I2C4_SPEED 100000 404 #define I2C_MUX_PCA_ADDR_PRI 0x77 /* I2C bus multiplexer,primary */ 405 #define I2C_MUX_PCA_ADDR_SEC1 0x75 /* I2C bus multiplexer,secondary 1 */ 406 #define I2C_MUX_PCA_ADDR_SEC2 0x76 /* I2C bus multiplexer,secondary 2 */ 407 #define I2C_MUX_CH_DEFAULT 0x8 408 409 #define I2C_MUX_CH_VOL_MONITOR 0xa 410 411 #define CONFIG_VID_FLS_ENV "t208xrdb_vdd_mv" 412 #ifndef CONFIG_SPL_BUILD 413 #define CONFIG_VID 414 #endif 415 #define CONFIG_VOL_MONITOR_IR36021_SET 416 #define CONFIG_VOL_MONITOR_IR36021_READ 417 /* The lowest and highest voltage allowed for T208xRDB */ 418 #define VDD_MV_MIN 819 419 #define VDD_MV_MAX 1212 420 421 /* 422 * RapidIO 423 */ 424 #define CONFIG_SYS_SRIO1_MEM_VIRT 0xa0000000 425 #define CONFIG_SYS_SRIO1_MEM_PHYS 0xc20000000ull 426 #define CONFIG_SYS_SRIO1_MEM_SIZE 0x10000000 /* 256M */ 427 #define CONFIG_SYS_SRIO2_MEM_VIRT 0xb0000000 428 #define CONFIG_SYS_SRIO2_MEM_PHYS 0xc30000000ull 429 #define CONFIG_SYS_SRIO2_MEM_SIZE 0x10000000 /* 256M */ 430 /* 431 * for slave u-boot IMAGE instored in master memory space, 432 * PHYS must be aligned based on the SIZE 433 */ 434 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull 435 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull 436 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x100000 /* 1M */ 437 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull 438 /* 439 * for slave UCODE and ENV instored in master memory space, 440 * PHYS must be aligned based on the SIZE 441 */ 442 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull 443 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull 444 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */ 445 446 /* slave core release by master*/ 447 #define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4 448 #define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */ 449 450 /* 451 * SRIO_PCIE_BOOT - SLAVE 452 */ 453 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE 454 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000 455 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \ 456 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR) 457 #endif 458 459 /* 460 * eSPI - Enhanced SPI 461 */ 462 #ifdef CONFIG_SPI_FLASH 463 #define CONFIG_SPI_FLASH_BAR 464 #define CONFIG_SF_DEFAULT_SPEED 10000000 465 #define CONFIG_SF_DEFAULT_MODE 0 466 #endif 467 468 /* 469 * General PCI 470 * Memory space is mapped 1-1, but I/O space must start from 0. 471 */ 472 #define CONFIG_PCIE1 /* PCIE controller 1 */ 473 #define CONFIG_PCIE2 /* PCIE controller 2 */ 474 #define CONFIG_PCIE3 /* PCIE controller 3 */ 475 #define CONFIG_PCIE4 /* PCIE controller 4 */ 476 #define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ 477 #define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ 478 /* controller 1, direct to uli, tgtid 3, Base address 20000 */ 479 #define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 480 #define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 481 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull 482 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ 483 #define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000 484 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 485 #define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull 486 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ 487 488 /* controller 2, Slot 2, tgtid 2, Base address 201000 */ 489 #define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 490 #define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000 491 #define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull 492 #define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */ 493 #define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000 494 #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 495 #define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull 496 #define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ 497 498 /* controller 3, Slot 1, tgtid 1, Base address 202000 */ 499 #define CONFIG_SYS_PCIE3_MEM_VIRT 0xb0000000 500 #define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000 501 #define CONFIG_SYS_PCIE3_MEM_PHYS 0xc30000000ull 502 #define CONFIG_SYS_PCIE3_MEM_SIZE 0x10000000 /* 256M */ 503 #define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000 504 #define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 505 #define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull 506 #define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */ 507 508 /* controller 4, Base address 203000 */ 509 #define CONFIG_SYS_PCIE4_MEM_VIRT 0xc0000000 510 #define CONFIG_SYS_PCIE4_MEM_BUS 0xe0000000 511 #define CONFIG_SYS_PCIE4_MEM_PHYS 0xc40000000ull 512 #define CONFIG_SYS_PCIE4_MEM_SIZE 0x10000000 /* 256M */ 513 #define CONFIG_SYS_PCIE4_IO_BUS 0x00000000 514 #define CONFIG_SYS_PCIE4_IO_PHYS 0xff8030000ull 515 #define CONFIG_SYS_PCIE4_IO_SIZE 0x00010000 /* 64k */ 516 517 #ifdef CONFIG_PCI 518 #define CONFIG_PCI_INDIRECT_BRIDGE 519 #define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata LSZ ADD */ 520 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 521 #endif 522 523 /* Qman/Bman */ 524 #ifndef CONFIG_NOBQFMAN 525 #define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */ 526 #define CONFIG_SYS_BMAN_NUM_PORTALS 18 527 #define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000 528 #define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull 529 #define CONFIG_SYS_BMAN_MEM_SIZE 0x02000000 530 #define CONFIG_SYS_BMAN_SP_CENA_SIZE 0x4000 531 #define CONFIG_SYS_BMAN_SP_CINH_SIZE 0x1000 532 #define CONFIG_SYS_BMAN_CENA_BASE CONFIG_SYS_BMAN_MEM_BASE 533 #define CONFIG_SYS_BMAN_CENA_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) 534 #define CONFIG_SYS_BMAN_CINH_BASE (CONFIG_SYS_BMAN_MEM_BASE + \ 535 CONFIG_SYS_BMAN_CENA_SIZE) 536 #define CONFIG_SYS_BMAN_CINH_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) 537 #define CONFIG_SYS_BMAN_SWP_ISDR_REG 0xE08 538 #define CONFIG_SYS_QMAN_NUM_PORTALS 18 539 #define CONFIG_SYS_QMAN_MEM_BASE 0xf6000000 540 #define CONFIG_SYS_QMAN_MEM_PHYS 0xff6000000ull 541 #define CONFIG_SYS_QMAN_MEM_SIZE 0x02000000 542 #define CONFIG_SYS_QMAN_SP_CENA_SIZE 0x4000 543 #define CONFIG_SYS_QMAN_SP_CINH_SIZE 0x1000 544 #define CONFIG_SYS_QMAN_CENA_BASE CONFIG_SYS_QMAN_MEM_BASE 545 #define CONFIG_SYS_QMAN_CENA_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) 546 #define CONFIG_SYS_QMAN_CINH_BASE (CONFIG_SYS_QMAN_MEM_BASE + \ 547 CONFIG_SYS_QMAN_CENA_SIZE) 548 #define CONFIG_SYS_QMAN_CINH_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) 549 #define CONFIG_SYS_QMAN_SWP_ISDR_REG 0xE08 550 551 #define CONFIG_SYS_DPAA_FMAN 552 #define CONFIG_SYS_DPAA_PME 553 #define CONFIG_SYS_PMAN 554 #define CONFIG_SYS_DPAA_DCE 555 #define CONFIG_SYS_DPAA_RMAN /* RMan */ 556 #define CONFIG_SYS_INTERLAKEN 557 558 /* Default address of microcode for the Linux Fman driver */ 559 #if defined(CONFIG_SPIFLASH) 560 /* 561 * env is stored at 0x100000, sector size is 0x10000, ucode is stored after 562 * env, so we got 0x110000. 563 */ 564 #define CONFIG_SYS_QE_FW_IN_SPIFLASH 565 #define CONFIG_SYS_CORTINA_FW_IN_SPIFLASH 566 #define CONFIG_SYS_FMAN_FW_ADDR 0x110000 567 #define CONFIG_CORTINA_FW_ADDR 0x120000 568 569 #elif defined(CONFIG_SDCARD) 570 /* 571 * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is 572 * about 1MB (2048 blocks), Env is stored after the image, and the env size is 573 * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080. 574 */ 575 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC 576 #define CONFIG_SYS_CORTINA_FW_IN_MMC 577 #define CONFIG_SYS_FMAN_FW_ADDR (512 * 0x820) 578 #define CONFIG_CORTINA_FW_ADDR (512 * 0x8a0) 579 580 #elif defined(CONFIG_NAND) 581 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND 582 #define CONFIG_SYS_CORTINA_FW_IN_NAND 583 #define CONFIG_SYS_FMAN_FW_ADDR (3 * CONFIG_SYS_NAND_BLOCK_SIZE) 584 #define CONFIG_CORTINA_FW_ADDR (4 * CONFIG_SYS_NAND_BLOCK_SIZE) 585 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) 586 /* 587 * Slave has no ucode locally, it can fetch this from remote. When implementing 588 * in two corenet boards, slave's ucode could be stored in master's memory 589 * space, the address can be mapped from slave TLB->slave LAW-> 590 * slave SRIO or PCIE outbound window->master inbound window-> 591 * master LAW->the ucode address in master's memory space. 592 */ 593 #define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE 594 #define CONFIG_SYS_CORTINA_FW_IN_REMOTE 595 #define CONFIG_SYS_FMAN_FW_ADDR 0xFFE00000 596 #define CONFIG_CORTINA_FW_ADDR 0xFFE10000 597 #else 598 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR 599 #define CONFIG_SYS_CORTINA_FW_IN_NOR 600 #define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000 601 #define CONFIG_CORTINA_FW_ADDR 0xEFE00000 602 #endif 603 #define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 604 #define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) 605 #endif /* CONFIG_NOBQFMAN */ 606 607 #ifdef CONFIG_SYS_DPAA_FMAN 608 #define CONFIG_FMAN_ENET 609 #define CONFIG_PHYLIB_10G 610 #define CONFIG_PHY_AQUANTIA 611 #define CONFIG_PHY_CORTINA 612 #define CONFIG_PHY_REALTEK 613 #define CONFIG_CORTINA_FW_LENGTH 0x40000 614 #define RGMII_PHY1_ADDR 0x01 /* RealTek RTL8211E */ 615 #define RGMII_PHY2_ADDR 0x02 616 #define CORTINA_PHY_ADDR1 0x0c /* Cortina CS4315 */ 617 #define CORTINA_PHY_ADDR2 0x0d 618 #define FM1_10GEC3_PHY_ADDR 0x00 /* Aquantia AQ1202 10G Base-T */ 619 #define FM1_10GEC4_PHY_ADDR 0x01 620 #endif 621 622 #ifdef CONFIG_FMAN_ENET 623 #define CONFIG_MII /* MII PHY management */ 624 #define CONFIG_ETHPRIME "FM1@DTSEC3" 625 #endif 626 627 /* 628 * SATA 629 */ 630 #ifdef CONFIG_FSL_SATA_V2 631 #define CONFIG_LIBATA 632 #define CONFIG_FSL_SATA 633 #define CONFIG_SYS_SATA_MAX_DEVICE 2 634 #define CONFIG_SATA1 635 #define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR 636 #define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA 637 #define CONFIG_SATA2 638 #define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR 639 #define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA 640 #define CONFIG_LBA48 641 #endif 642 643 /* 644 * USB 645 */ 646 #ifdef CONFIG_USB_EHCI_HCD 647 #define CONFIG_USB_EHCI_FSL 648 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET 649 #define CONFIG_HAS_FSL_DR_USB 650 #endif 651 652 /* 653 * SDHC 654 */ 655 #ifdef CONFIG_MMC 656 #define CONFIG_FSL_ESDHC 657 #define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR 658 #define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT 659 #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33 660 #endif 661 662 /* 663 * Dynamic MTD Partition support with mtdparts 664 */ 665 #ifdef CONFIG_MTD_NOR_FLASH 666 #define CONFIG_MTD_DEVICE 667 #define CONFIG_MTD_PARTITIONS 668 #define CONFIG_FLASH_CFI_MTD 669 #define MTDIDS_DEFAULT "nor0=fe8000000.nor,nand0=fff800000.flash," \ 670 "spi0=spife110000.1" 671 #define MTDPARTS_DEFAULT "mtdparts=fe8000000.nor:1m(uboot),5m(kernel)," \ 672 "128k(dtb),96m(fs),-(user);fff800000.flash:1m(uboot)," \ 673 "5m(kernel),128k(dtb),96m(fs),-(user);spife110000.1:" \ 674 "1m(uboot),5m(kernel),128k(dtb),-(user)" 675 #endif 676 677 /* 678 * Environment 679 */ 680 681 /* 682 * Miscellaneous configurable options 683 */ 684 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 685 #define CONFIG_CMDLINE_EDITING /* Command-line editing */ 686 #define CONFIG_AUTO_COMPLETE /* add autocompletion support */ 687 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 688 #ifdef CONFIG_CMD_KGDB 689 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 690 #else 691 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 692 #endif 693 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) 694 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 695 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */ 696 697 /* 698 * For booting Linux, the board info and command line data 699 * have to be in the first 64 MB of memory, since this is 700 * the maximum mapped by the Linux kernel during initialization. 701 */ 702 #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial map for Linux*/ 703 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 704 705 #ifdef CONFIG_CMD_KGDB 706 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ 707 #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ 708 #endif 709 710 /* 711 * Environment Configuration 712 */ 713 #define CONFIG_ROOTPATH "/opt/nfsroot" 714 #define CONFIG_BOOTFILE "uImage" 715 #define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server */ 716 717 /* default location for tftp and bootm */ 718 #define CONFIG_LOADADDR 1000000 719 #define __USB_PHY_TYPE utmi 720 721 #define CONFIG_EXTRA_ENV_SETTINGS \ 722 "hwconfig=fsl_ddr:" \ 723 "ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) "," \ 724 "bank_intlv=auto;" \ 725 "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\ 726 "netdev=eth0\0" \ 727 "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ 728 "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \ 729 "tftpflash=tftpboot $loadaddr $uboot && " \ 730 "protect off $ubootaddr +$filesize && " \ 731 "erase $ubootaddr +$filesize && " \ 732 "cp.b $loadaddr $ubootaddr $filesize && " \ 733 "protect on $ubootaddr +$filesize && " \ 734 "cmp.b $loadaddr $ubootaddr $filesize\0" \ 735 "consoledev=ttyS0\0" \ 736 "ramdiskaddr=2000000\0" \ 737 "ramdiskfile=t2080rdb/ramdisk.uboot\0" \ 738 "fdtaddr=1e00000\0" \ 739 "fdtfile=t2080rdb/t2080rdb.dtb\0" \ 740 "bdev=sda3\0" 741 742 /* 743 * For emulation this causes u-boot to jump to the start of the 744 * proof point app code automatically 745 */ 746 #define CONFIG_PROOF_POINTS \ 747 "setenv bootargs root=/dev/$bdev rw " \ 748 "console=$consoledev,$baudrate $othbootargs;" \ 749 "cpu 1 release 0x29000000 - - -;" \ 750 "cpu 2 release 0x29000000 - - -;" \ 751 "cpu 3 release 0x29000000 - - -;" \ 752 "cpu 4 release 0x29000000 - - -;" \ 753 "cpu 5 release 0x29000000 - - -;" \ 754 "cpu 6 release 0x29000000 - - -;" \ 755 "cpu 7 release 0x29000000 - - -;" \ 756 "go 0x29000000" 757 758 #define CONFIG_HVBOOT \ 759 "setenv bootargs config-addr=0x60000000; " \ 760 "bootm 0x01000000 - 0x00f00000" 761 762 #define CONFIG_ALU \ 763 "setenv bootargs root=/dev/$bdev rw " \ 764 "console=$consoledev,$baudrate $othbootargs;" \ 765 "cpu 1 release 0x01000000 - - -;" \ 766 "cpu 2 release 0x01000000 - - -;" \ 767 "cpu 3 release 0x01000000 - - -;" \ 768 "cpu 4 release 0x01000000 - - -;" \ 769 "cpu 5 release 0x01000000 - - -;" \ 770 "cpu 6 release 0x01000000 - - -;" \ 771 "cpu 7 release 0x01000000 - - -;" \ 772 "go 0x01000000" 773 774 #define CONFIG_LINUX \ 775 "setenv bootargs root=/dev/ram rw " \ 776 "console=$consoledev,$baudrate $othbootargs;" \ 777 "setenv ramdiskaddr 0x02000000;" \ 778 "setenv fdtaddr 0x00c00000;" \ 779 "setenv loadaddr 0x1000000;" \ 780 "bootm $loadaddr $ramdiskaddr $fdtaddr" 781 782 #define CONFIG_HDBOOT \ 783 "setenv bootargs root=/dev/$bdev rw " \ 784 "console=$consoledev,$baudrate $othbootargs;" \ 785 "tftp $loadaddr $bootfile;" \ 786 "tftp $fdtaddr $fdtfile;" \ 787 "bootm $loadaddr - $fdtaddr" 788 789 #define CONFIG_NFSBOOTCOMMAND \ 790 "setenv bootargs root=/dev/nfs rw " \ 791 "nfsroot=$serverip:$rootpath " \ 792 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 793 "console=$consoledev,$baudrate $othbootargs;" \ 794 "tftp $loadaddr $bootfile;" \ 795 "tftp $fdtaddr $fdtfile;" \ 796 "bootm $loadaddr - $fdtaddr" 797 798 #define CONFIG_RAMBOOTCOMMAND \ 799 "setenv bootargs root=/dev/ram rw " \ 800 "console=$consoledev,$baudrate $othbootargs;" \ 801 "tftp $ramdiskaddr $ramdiskfile;" \ 802 "tftp $loadaddr $bootfile;" \ 803 "tftp $fdtaddr $fdtfile;" \ 804 "bootm $loadaddr $ramdiskaddr $fdtaddr" 805 806 #define CONFIG_BOOTCOMMAND CONFIG_LINUX 807 808 #include <asm/fsl_secure_boot.h> 809 810 #endif /* __T2080RDB_H */ 811