1 /* 2 * Copyright 2014 Freescale Semiconductor, Inc. 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 /* 8 * T2080 RDB/PCIe board configuration file 9 */ 10 11 #ifndef __T2080RDB_H 12 #define __T2080RDB_H 13 14 #define CONFIG_T2080RDB 15 #define CONFIG_ICS307_REFCLK_HZ 25000000 /* ICS307 ref clk freq */ 16 #define CONFIG_MMC 17 #define CONFIG_USB_EHCI 18 #define CONFIG_FSL_SATA_V2 19 20 /* High Level Configuration Options */ 21 #define CONFIG_BOOKE 22 #define CONFIG_E500 /* BOOKE e500 family */ 23 #define CONFIG_E500MC /* BOOKE e500mc family */ 24 #define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */ 25 #define CONFIG_MP /* support multiple processors */ 26 #define CONFIG_ENABLE_36BIT_PHYS 27 28 #ifdef CONFIG_PHYS_64BIT 29 #define CONFIG_ADDR_MAP 1 30 #define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */ 31 #endif 32 33 #define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */ 34 #define CONFIG_SYS_NUM_CPC CONFIG_NUM_DDR_CONTROLLERS 35 #define CONFIG_FSL_IFC /* Enable IFC Support */ 36 #define CONFIG_FSL_CAAM /* Enable SEC/CAAM */ 37 #define CONFIG_ENV_OVERWRITE 38 39 #ifdef CONFIG_RAMBOOT_PBL 40 #define CONFIG_SYS_FSL_PBL_PBI board/freescale/t208xrdb/t2080_pbi.cfg 41 42 #define CONFIG_SPL_FLUSH_IMAGE 43 #define CONFIG_SPL_TARGET "u-boot-with-spl.bin" 44 #define CONFIG_SYS_TEXT_BASE 0x00201000 45 #define CONFIG_SPL_TEXT_BASE 0xFFFD8000 46 #define CONFIG_SPL_PAD_TO 0x40000 47 #define CONFIG_SPL_MAX_SIZE 0x28000 48 #define RESET_VECTOR_OFFSET 0x27FFC 49 #define BOOT_PAGE_OFFSET 0x27000 50 #ifdef CONFIG_SPL_BUILD 51 #define CONFIG_SPL_SKIP_RELOCATE 52 #define CONFIG_SPL_COMMON_INIT_DDR 53 #define CONFIG_SYS_CCSR_DO_NOT_RELOCATE 54 #define CONFIG_SYS_NO_FLASH 55 #endif 56 57 #ifdef CONFIG_NAND 58 #define CONFIG_SYS_NAND_U_BOOT_SIZE (768 << 10) 59 #define CONFIG_SYS_NAND_U_BOOT_DST 0x00200000 60 #define CONFIG_SYS_NAND_U_BOOT_START 0x00200000 61 #define CONFIG_SYS_NAND_U_BOOT_OFFS (256 << 10) 62 #define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot-nand.lds" 63 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xrdb/t2080_nand_rcw.cfg 64 #define CONFIG_SPL_NAND_BOOT 65 #endif 66 67 #ifdef CONFIG_SPIFLASH 68 #define CONFIG_RESET_VECTOR_ADDRESS 0x200FFC 69 #define CONFIG_SPL_SPI_FLASH_MINIMAL 70 #define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE (768 << 10) 71 #define CONFIG_SYS_SPI_FLASH_U_BOOT_DST (0x00200000) 72 #define CONFIG_SYS_SPI_FLASH_U_BOOT_START (0x00200000) 73 #define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS (256 << 10) 74 #define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot.lds" 75 #ifndef CONFIG_SPL_BUILD 76 #define CONFIG_SYS_MPC85XX_NO_RESETVEC 77 #endif 78 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xrdb/t2080_spi_rcw.cfg 79 #define CONFIG_SPL_SPI_BOOT 80 #endif 81 82 #ifdef CONFIG_SDCARD 83 #define CONFIG_RESET_VECTOR_ADDRESS 0x200FFC 84 #define CONFIG_SPL_MMC_MINIMAL 85 #define CONFIG_SYS_MMC_U_BOOT_SIZE (768 << 10) 86 #define CONFIG_SYS_MMC_U_BOOT_DST (0x00200000) 87 #define CONFIG_SYS_MMC_U_BOOT_START (0x00200000) 88 #define CONFIG_SYS_MMC_U_BOOT_OFFS (260 << 10) 89 #define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot.lds" 90 #ifndef CONFIG_SPL_BUILD 91 #define CONFIG_SYS_MPC85XX_NO_RESETVEC 92 #endif 93 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xrdb/t2080_sd_rcw.cfg 94 #define CONFIG_SPL_MMC_BOOT 95 #endif 96 97 #endif /* CONFIG_RAMBOOT_PBL */ 98 99 #define CONFIG_SRIO_PCIE_BOOT_MASTER 100 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE 101 /* Set 1M boot space */ 102 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000) 103 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \ 104 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR) 105 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc 106 #define CONFIG_SYS_NO_FLASH 107 #endif 108 109 #ifndef CONFIG_SYS_TEXT_BASE 110 #define CONFIG_SYS_TEXT_BASE 0xeff40000 111 #endif 112 113 #ifndef CONFIG_RESET_VECTOR_ADDRESS 114 #define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc 115 #endif 116 117 /* 118 * These can be toggled for performance analysis, otherwise use default. 119 */ 120 #define CONFIG_SYS_CACHE_STASHING 121 #define CONFIG_BTB /* toggle branch predition */ 122 #define CONFIG_DDR_ECC 123 #ifdef CONFIG_DDR_ECC 124 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER 125 #define CONFIG_MEM_INIT_VALUE 0xdeadbeef 126 #endif 127 128 #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ 129 #define CONFIG_SYS_MEMTEST_END 0x00400000 130 #define CONFIG_SYS_ALT_MEMTEST 131 132 #ifndef CONFIG_SYS_NO_FLASH 133 #define CONFIG_FLASH_CFI_DRIVER 134 #define CONFIG_SYS_FLASH_CFI 135 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 136 #endif 137 138 #if defined(CONFIG_SPIFLASH) 139 #define CONFIG_SYS_EXTRA_ENV_RELOC 140 #define CONFIG_ENV_IS_IN_SPI_FLASH 141 #define CONFIG_ENV_SPI_BUS 0 142 #define CONFIG_ENV_SPI_CS 0 143 #define CONFIG_ENV_SPI_MAX_HZ 10000000 144 #define CONFIG_ENV_SPI_MODE 0 145 #define CONFIG_ENV_SIZE 0x2000 /* 8KB */ 146 #define CONFIG_ENV_OFFSET 0x100000 /* 1MB */ 147 #define CONFIG_ENV_SECT_SIZE 0x10000 148 #elif defined(CONFIG_SDCARD) 149 #define CONFIG_SYS_EXTRA_ENV_RELOC 150 #define CONFIG_ENV_IS_IN_MMC 151 #define CONFIG_SYS_MMC_ENV_DEV 0 152 #define CONFIG_ENV_SIZE 0x2000 153 #define CONFIG_ENV_OFFSET (512 * 0x800) 154 #elif defined(CONFIG_NAND) 155 #define CONFIG_SYS_EXTRA_ENV_RELOC 156 #define CONFIG_ENV_IS_IN_NAND 157 #define CONFIG_ENV_SIZE 0x2000 158 #define CONFIG_ENV_OFFSET (2 * CONFIG_SYS_NAND_BLOCK_SIZE) 159 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) 160 #define CONFIG_ENV_IS_IN_REMOTE 161 #define CONFIG_ENV_ADDR 0xffe20000 162 #define CONFIG_ENV_SIZE 0x2000 163 #elif defined(CONFIG_ENV_IS_NOWHERE) 164 #define CONFIG_ENV_SIZE 0x2000 165 #else 166 #define CONFIG_ENV_IS_IN_FLASH 167 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) 168 #define CONFIG_ENV_SIZE 0x2000 169 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ 170 #endif 171 172 #ifndef __ASSEMBLY__ 173 unsigned long get_board_sys_clk(void); 174 unsigned long get_board_ddr_clk(void); 175 #endif 176 177 #define CONFIG_SYS_CLK_FREQ 66660000 178 #define CONFIG_DDR_CLK_FREQ 133330000 179 180 /* 181 * Config the L3 Cache as L3 SRAM 182 */ 183 #define CONFIG_SYS_INIT_L3_ADDR 0xFFFC0000 184 #define CONFIG_SYS_L3_SIZE (512 << 10) 185 #define CONFIG_SPL_GD_ADDR (CONFIG_SYS_INIT_L3_ADDR + 32 * 1024) 186 #ifdef CONFIG_RAMBOOT_PBL 187 #define CONFIG_ENV_ADDR (CONFIG_SPL_GD_ADDR + 4 * 1024) 188 #endif 189 #define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SPL_GD_ADDR + 12 * 1024) 190 #define CONFIG_SPL_RELOC_MALLOC_SIZE (50 << 10) 191 #define CONFIG_SPL_RELOC_STACK (CONFIG_SPL_GD_ADDR + 64 * 1024) 192 #define CONFIG_SPL_RELOC_STACK_SIZE (22 << 10) 193 194 #define CONFIG_SYS_DCSRBAR 0xf0000000 195 #define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull 196 197 /* EEPROM */ 198 #define CONFIG_ID_EEPROM 199 #define CONFIG_SYS_I2C_EEPROM_NXID 200 #define CONFIG_SYS_EEPROM_BUS_NUM 0 201 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 202 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 203 204 /* 205 * DDR Setup 206 */ 207 #define CONFIG_VERY_BIG_RAM 208 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 209 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 210 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 211 #define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR) 212 #define CONFIG_DDR_SPD 213 #define CONFIG_SYS_FSL_DDR3 214 #undef CONFIG_FSL_DDR_INTERACTIVE 215 #define CONFIG_SYS_SPD_BUS_NUM 0 216 #define CONFIG_SYS_SDRAM_SIZE 2048 /* for fixed parameter use */ 217 #define SPD_EEPROM_ADDRESS1 0x51 218 #define SPD_EEPROM_ADDRESS2 0x52 219 #define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1 220 #define CTRL_INTLV_PREFERED cacheline 221 222 /* 223 * IFC Definitions 224 */ 225 #define CONFIG_SYS_FLASH_BASE 0xe8000000 226 #define CONFIG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CONFIG_SYS_FLASH_BASE) 227 #define CONFIG_SYS_NOR0_CSPR_EXT (0xf) 228 #define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \ 229 CSPR_PORT_SIZE_16 | \ 230 CSPR_MSEL_NOR | \ 231 CSPR_V) 232 #define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024) 233 234 /* NOR Flash Timing Params */ 235 #define CONFIG_SYS_NOR_CSOR CSOR_NAND_TRHZ_80 236 237 #define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \ 238 FTIM0_NOR_TEADC(0x5) | \ 239 FTIM0_NOR_TEAHC(0x5)) 240 #define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \ 241 FTIM1_NOR_TRAD_NOR(0x1A) |\ 242 FTIM1_NOR_TSEQRAD_NOR(0x13)) 243 #define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \ 244 FTIM2_NOR_TCH(0x4) | \ 245 FTIM2_NOR_TWPH(0x0E) | \ 246 FTIM2_NOR_TWP(0x1c)) 247 #define CONFIG_SYS_NOR_FTIM3 0x0 248 249 #define CONFIG_SYS_FLASH_QUIET_TEST 250 #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ 251 252 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 253 #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ 254 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 255 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 256 #define CONFIG_SYS_FLASH_EMPTY_INFO 257 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS } 258 259 /* CPLD on IFC */ 260 #define CONFIG_SYS_CPLD_BASE 0xffdf0000 261 #define CONFIG_SYS_CPLD_BASE_PHYS (0xf00000000ull | CONFIG_SYS_CPLD_BASE) 262 #define CONFIG_SYS_CSPR2_EXT (0xf) 263 #define CONFIG_SYS_CSPR2 (CSPR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE) \ 264 | CSPR_PORT_SIZE_8 \ 265 | CSPR_MSEL_GPCM \ 266 | CSPR_V) 267 #define CONFIG_SYS_AMASK2 IFC_AMASK(64*1024) 268 #define CONFIG_SYS_CSOR2 0x0 269 270 /* CPLD Timing parameters for IFC CS2 */ 271 #define CONFIG_SYS_CS2_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \ 272 FTIM0_GPCM_TEADC(0x0e) | \ 273 FTIM0_GPCM_TEAHC(0x0e)) 274 #define CONFIG_SYS_CS2_FTIM1 (FTIM1_GPCM_TACO(0x0e) | \ 275 FTIM1_GPCM_TRAD(0x1f)) 276 #define CONFIG_SYS_CS2_FTIM2 (FTIM2_GPCM_TCS(0x0e) | \ 277 FTIM2_GPCM_TCH(0x8) | \ 278 FTIM2_GPCM_TWP(0x1f)) 279 #define CONFIG_SYS_CS2_FTIM3 0x0 280 281 /* NAND Flash on IFC */ 282 #define CONFIG_NAND_FSL_IFC 283 #define CONFIG_SYS_NAND_BASE 0xff800000 284 #define CONFIG_SYS_NAND_BASE_PHYS (0xf00000000ull | CONFIG_SYS_NAND_BASE) 285 286 #define CONFIG_SYS_NAND_CSPR_EXT (0xf) 287 #define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ 288 | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \ 289 | CSPR_MSEL_NAND /* MSEL = NAND */ \ 290 | CSPR_V) 291 #define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024) 292 293 #define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \ 294 | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \ 295 | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \ 296 | CSOR_NAND_RAL_3 /* RAL = 2Byes */ \ 297 | CSOR_NAND_PGS_2K /* Page Size = 2K */\ 298 | CSOR_NAND_SPRZ_64 /* Spare size = 64 */\ 299 | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/ 300 301 #define CONFIG_SYS_NAND_ONFI_DETECTION 302 303 /* ONFI NAND Flash mode0 Timing Params */ 304 #define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \ 305 FTIM0_NAND_TWP(0x18) | \ 306 FTIM0_NAND_TWCHT(0x07) | \ 307 FTIM0_NAND_TWH(0x0a)) 308 #define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \ 309 FTIM1_NAND_TWBE(0x39) | \ 310 FTIM1_NAND_TRR(0x0e) | \ 311 FTIM1_NAND_TRP(0x18)) 312 #define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \ 313 FTIM2_NAND_TREH(0x0a) | \ 314 FTIM2_NAND_TWHRE(0x1e)) 315 #define CONFIG_SYS_NAND_FTIM3 0x0 316 317 #define CONFIG_SYS_NAND_DDR_LAW 11 318 #define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } 319 #define CONFIG_SYS_MAX_NAND_DEVICE 1 320 #define CONFIG_CMD_NAND 321 #define CONFIG_SYS_NAND_BLOCK_SIZE (512 * 1024) 322 323 #if defined(CONFIG_NAND) 324 #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT 325 #define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR 326 #define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK 327 #define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR 328 #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0 329 #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1 330 #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2 331 #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3 332 #define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR0_CSPR_EXT 333 #define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR0_CSPR 334 #define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK 335 #define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR 336 #define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0 337 #define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1 338 #define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2 339 #define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3 340 #else 341 #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT 342 #define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR 343 #define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK 344 #define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR 345 #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0 346 #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1 347 #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2 348 #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3 349 #define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NAND_CSPR_EXT 350 #define CONFIG_SYS_CSPR1 CONFIG_SYS_NAND_CSPR 351 #define CONFIG_SYS_AMASK1 CONFIG_SYS_NAND_AMASK 352 #define CONFIG_SYS_CSOR1 CONFIG_SYS_NAND_CSOR 353 #define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NAND_FTIM0 354 #define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NAND_FTIM1 355 #define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NAND_FTIM2 356 #define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NAND_FTIM3 357 #endif 358 359 #if defined(CONFIG_RAMBOOT_PBL) 360 #define CONFIG_SYS_RAMBOOT 361 #endif 362 363 #ifdef CONFIG_SPL_BUILD 364 #define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE 365 #else 366 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 367 #endif 368 369 #define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */ 370 #define CONFIG_MISC_INIT_R 371 #define CONFIG_HWCONFIG 372 373 /* define to use L1 as initial stack */ 374 #define CONFIG_L1_INIT_RAM 375 #define CONFIG_SYS_INIT_RAM_LOCK 376 #define CONFIG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */ 377 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf 378 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW 0xfe03c000 379 /* The assembler doesn't like typecast */ 380 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \ 381 ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \ 382 CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW) 383 #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 384 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ 385 GENERATED_GBL_DATA_SIZE) 386 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 387 #define CONFIG_SYS_MONITOR_LEN (768 * 1024) 388 #define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024) 389 390 /* 391 * Serial Port 392 */ 393 #define CONFIG_CONS_INDEX 1 394 #define CONFIG_SYS_NS16550_SERIAL 395 #define CONFIG_SYS_NS16550_REG_SIZE 1 396 #define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2) 397 #define CONFIG_SYS_BAUDRATE_TABLE \ 398 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} 399 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500) 400 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600) 401 #define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500) 402 #define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600) 403 404 /* 405 * I2C 406 */ 407 #define CONFIG_SYS_I2C 408 #define CONFIG_SYS_I2C_FSL 409 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 410 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F 411 #define CONFIG_SYS_FSL_I2C3_SLAVE 0x7F 412 #define CONFIG_SYS_FSL_I2C4_SLAVE 0x7F 413 #define CONFIG_SYS_FSL_I2C_OFFSET 0x118000 414 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100 415 #define CONFIG_SYS_FSL_I2C3_OFFSET 0x119000 416 #define CONFIG_SYS_FSL_I2C4_OFFSET 0x119100 417 #define CONFIG_SYS_FSL_I2C_SPEED 100000 418 #define CONFIG_SYS_FSL_I2C2_SPEED 100000 419 #define CONFIG_SYS_FSL_I2C3_SPEED 100000 420 #define CONFIG_SYS_FSL_I2C4_SPEED 100000 421 #define I2C_MUX_PCA_ADDR_PRI 0x77 /* I2C bus multiplexer,primary */ 422 #define I2C_MUX_PCA_ADDR_SEC1 0x75 /* I2C bus multiplexer,secondary 1 */ 423 #define I2C_MUX_PCA_ADDR_SEC2 0x76 /* I2C bus multiplexer,secondary 2 */ 424 #define I2C_MUX_CH_DEFAULT 0x8 425 426 #define I2C_MUX_CH_VOL_MONITOR 0xa 427 428 #define CONFIG_VID_FLS_ENV "t208xrdb_vdd_mv" 429 #ifndef CONFIG_SPL_BUILD 430 #define CONFIG_VID 431 #endif 432 #define CONFIG_VOL_MONITOR_IR36021_SET 433 #define CONFIG_VOL_MONITOR_IR36021_READ 434 /* The lowest and highest voltage allowed for T208xRDB */ 435 #define VDD_MV_MIN 819 436 #define VDD_MV_MAX 1212 437 438 /* 439 * RapidIO 440 */ 441 #define CONFIG_SYS_SRIO1_MEM_VIRT 0xa0000000 442 #define CONFIG_SYS_SRIO1_MEM_PHYS 0xc20000000ull 443 #define CONFIG_SYS_SRIO1_MEM_SIZE 0x10000000 /* 256M */ 444 #define CONFIG_SYS_SRIO2_MEM_VIRT 0xb0000000 445 #define CONFIG_SYS_SRIO2_MEM_PHYS 0xc30000000ull 446 #define CONFIG_SYS_SRIO2_MEM_SIZE 0x10000000 /* 256M */ 447 /* 448 * for slave u-boot IMAGE instored in master memory space, 449 * PHYS must be aligned based on the SIZE 450 */ 451 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull 452 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull 453 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x100000 /* 1M */ 454 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull 455 /* 456 * for slave UCODE and ENV instored in master memory space, 457 * PHYS must be aligned based on the SIZE 458 */ 459 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull 460 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull 461 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */ 462 463 /* slave core release by master*/ 464 #define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4 465 #define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */ 466 467 /* 468 * SRIO_PCIE_BOOT - SLAVE 469 */ 470 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE 471 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000 472 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \ 473 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR) 474 #endif 475 476 /* 477 * eSPI - Enhanced SPI 478 */ 479 #ifdef CONFIG_SPI_FLASH 480 #define CONFIG_SPI_FLASH_BAR 481 #define CONFIG_SF_DEFAULT_SPEED 10000000 482 #define CONFIG_SF_DEFAULT_MODE 0 483 #endif 484 485 /* 486 * General PCI 487 * Memory space is mapped 1-1, but I/O space must start from 0. 488 */ 489 #define CONFIG_PCIE1 /* PCIE controller 1 */ 490 #define CONFIG_PCIE2 /* PCIE controller 2 */ 491 #define CONFIG_PCIE3 /* PCIE controller 3 */ 492 #define CONFIG_PCIE4 /* PCIE controller 4 */ 493 #define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ 494 #define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ 495 /* controller 1, direct to uli, tgtid 3, Base address 20000 */ 496 #define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 497 #define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 498 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull 499 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ 500 #define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000 501 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 502 #define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull 503 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ 504 505 /* controller 2, Slot 2, tgtid 2, Base address 201000 */ 506 #define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 507 #define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000 508 #define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull 509 #define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */ 510 #define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000 511 #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 512 #define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull 513 #define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ 514 515 /* controller 3, Slot 1, tgtid 1, Base address 202000 */ 516 #define CONFIG_SYS_PCIE3_MEM_VIRT 0xb0000000 517 #define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000 518 #define CONFIG_SYS_PCIE3_MEM_PHYS 0xc30000000ull 519 #define CONFIG_SYS_PCIE3_MEM_SIZE 0x10000000 /* 256M */ 520 #define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000 521 #define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 522 #define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull 523 #define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */ 524 525 /* controller 4, Base address 203000 */ 526 #define CONFIG_SYS_PCIE4_MEM_VIRT 0xc0000000 527 #define CONFIG_SYS_PCIE4_MEM_BUS 0xe0000000 528 #define CONFIG_SYS_PCIE4_MEM_PHYS 0xc40000000ull 529 #define CONFIG_SYS_PCIE4_MEM_SIZE 0x10000000 /* 256M */ 530 #define CONFIG_SYS_PCIE4_IO_BUS 0x00000000 531 #define CONFIG_SYS_PCIE4_IO_PHYS 0xff8030000ull 532 #define CONFIG_SYS_PCIE4_IO_SIZE 0x00010000 /* 64k */ 533 534 #ifdef CONFIG_PCI 535 #define CONFIG_PCI_INDIRECT_BRIDGE 536 #define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata LSZ ADD */ 537 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 538 #define CONFIG_DOS_PARTITION 539 #endif 540 541 /* Qman/Bman */ 542 #ifndef CONFIG_NOBQFMAN 543 #define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */ 544 #define CONFIG_SYS_BMAN_NUM_PORTALS 18 545 #define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000 546 #define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull 547 #define CONFIG_SYS_BMAN_MEM_SIZE 0x02000000 548 #define CONFIG_SYS_BMAN_SP_CENA_SIZE 0x4000 549 #define CONFIG_SYS_BMAN_SP_CINH_SIZE 0x1000 550 #define CONFIG_SYS_BMAN_CENA_BASE CONFIG_SYS_BMAN_MEM_BASE 551 #define CONFIG_SYS_BMAN_CENA_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) 552 #define CONFIG_SYS_BMAN_CINH_BASE (CONFIG_SYS_BMAN_MEM_BASE + \ 553 CONFIG_SYS_BMAN_CENA_SIZE) 554 #define CONFIG_SYS_BMAN_CINH_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) 555 #define CONFIG_SYS_BMAN_SWP_ISDR_REG 0xE08 556 #define CONFIG_SYS_QMAN_NUM_PORTALS 18 557 #define CONFIG_SYS_QMAN_MEM_BASE 0xf6000000 558 #define CONFIG_SYS_QMAN_MEM_PHYS 0xff6000000ull 559 #define CONFIG_SYS_QMAN_MEM_SIZE 0x02000000 560 #define CONFIG_SYS_QMAN_SP_CENA_SIZE 0x4000 561 #define CONFIG_SYS_QMAN_SP_CINH_SIZE 0x1000 562 #define CONFIG_SYS_QMAN_CENA_BASE CONFIG_SYS_QMAN_MEM_BASE 563 #define CONFIG_SYS_QMAN_CENA_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) 564 #define CONFIG_SYS_QMAN_CINH_BASE (CONFIG_SYS_QMAN_MEM_BASE + \ 565 CONFIG_SYS_QMAN_CENA_SIZE) 566 #define CONFIG_SYS_QMAN_CINH_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) 567 #define CONFIG_SYS_QMAN_SWP_ISDR_REG 0xE08 568 569 #define CONFIG_SYS_DPAA_FMAN 570 #define CONFIG_SYS_DPAA_PME 571 #define CONFIG_SYS_PMAN 572 #define CONFIG_SYS_DPAA_DCE 573 #define CONFIG_SYS_DPAA_RMAN /* RMan */ 574 #define CONFIG_SYS_INTERLAKEN 575 576 /* Default address of microcode for the Linux Fman driver */ 577 #if defined(CONFIG_SPIFLASH) 578 /* 579 * env is stored at 0x100000, sector size is 0x10000, ucode is stored after 580 * env, so we got 0x110000. 581 */ 582 #define CONFIG_SYS_QE_FW_IN_SPIFLASH 583 #define CONFIG_SYS_CORTINA_FW_IN_SPIFLASH 584 #define CONFIG_SYS_FMAN_FW_ADDR 0x110000 585 #define CONFIG_CORTINA_FW_ADDR 0x120000 586 587 #elif defined(CONFIG_SDCARD) 588 /* 589 * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is 590 * about 1MB (2048 blocks), Env is stored after the image, and the env size is 591 * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080. 592 */ 593 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC 594 #define CONFIG_SYS_CORTINA_FW_IN_MMC 595 #define CONFIG_SYS_FMAN_FW_ADDR (512 * 0x820) 596 #define CONFIG_CORTINA_FW_ADDR (512 * 0x8a0) 597 598 #elif defined(CONFIG_NAND) 599 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND 600 #define CONFIG_SYS_CORTINA_FW_IN_NAND 601 #define CONFIG_SYS_FMAN_FW_ADDR (3 * CONFIG_SYS_NAND_BLOCK_SIZE) 602 #define CONFIG_CORTINA_FW_ADDR (4 * CONFIG_SYS_NAND_BLOCK_SIZE) 603 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) 604 /* 605 * Slave has no ucode locally, it can fetch this from remote. When implementing 606 * in two corenet boards, slave's ucode could be stored in master's memory 607 * space, the address can be mapped from slave TLB->slave LAW-> 608 * slave SRIO or PCIE outbound window->master inbound window-> 609 * master LAW->the ucode address in master's memory space. 610 */ 611 #define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE 612 #define CONFIG_SYS_CORTINA_FW_IN_REMOTE 613 #define CONFIG_SYS_FMAN_FW_ADDR 0xFFE00000 614 #define CONFIG_CORTINA_FW_ADDR 0xFFE10000 615 #else 616 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR 617 #define CONFIG_SYS_CORTINA_FW_IN_NOR 618 #define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000 619 #define CONFIG_CORTINA_FW_ADDR 0xEFE00000 620 #endif 621 #define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 622 #define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) 623 #endif /* CONFIG_NOBQFMAN */ 624 625 #ifdef CONFIG_SYS_DPAA_FMAN 626 #define CONFIG_FMAN_ENET 627 #define CONFIG_PHYLIB_10G 628 #define CONFIG_PHY_AQUANTIA 629 #define CONFIG_PHY_CORTINA 630 #define CONFIG_PHY_REALTEK 631 #define CONFIG_CORTINA_FW_LENGTH 0x40000 632 #define RGMII_PHY1_ADDR 0x01 /* RealTek RTL8211E */ 633 #define RGMII_PHY2_ADDR 0x02 634 #define CORTINA_PHY_ADDR1 0x0c /* Cortina CS4315 */ 635 #define CORTINA_PHY_ADDR2 0x0d 636 #define FM1_10GEC3_PHY_ADDR 0x00 /* Aquantia AQ1202 10G Base-T */ 637 #define FM1_10GEC4_PHY_ADDR 0x01 638 #endif 639 640 #ifdef CONFIG_FMAN_ENET 641 #define CONFIG_MII /* MII PHY management */ 642 #define CONFIG_ETHPRIME "FM1@DTSEC3" 643 #define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ 644 #endif 645 646 /* 647 * SATA 648 */ 649 #ifdef CONFIG_FSL_SATA_V2 650 #define CONFIG_LIBATA 651 #define CONFIG_FSL_SATA 652 #define CONFIG_SYS_SATA_MAX_DEVICE 2 653 #define CONFIG_SATA1 654 #define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR 655 #define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA 656 #define CONFIG_SATA2 657 #define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR 658 #define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA 659 #define CONFIG_LBA48 660 #define CONFIG_CMD_SATA 661 #define CONFIG_DOS_PARTITION 662 #endif 663 664 /* 665 * USB 666 */ 667 #ifdef CONFIG_USB_EHCI 668 #define CONFIG_USB_EHCI_FSL 669 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET 670 #define CONFIG_HAS_FSL_DR_USB 671 #endif 672 673 /* 674 * SDHC 675 */ 676 #ifdef CONFIG_MMC 677 #define CONFIG_FSL_ESDHC 678 #define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR 679 #define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT 680 #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33 681 #define CONFIG_GENERIC_MMC 682 #define CONFIG_DOS_PARTITION 683 #endif 684 685 /* 686 * Dynamic MTD Partition support with mtdparts 687 */ 688 #ifndef CONFIG_SYS_NO_FLASH 689 #define CONFIG_MTD_DEVICE 690 #define CONFIG_MTD_PARTITIONS 691 #define CONFIG_CMD_MTDPARTS 692 #define CONFIG_FLASH_CFI_MTD 693 #define MTDIDS_DEFAULT "nor0=fe8000000.nor,nand0=fff800000.flash," \ 694 "spi0=spife110000.1" 695 #define MTDPARTS_DEFAULT "mtdparts=fe8000000.nor:1m(uboot),5m(kernel)," \ 696 "128k(dtb),96m(fs),-(user);fff800000.flash:1m(uboot)," \ 697 "5m(kernel),128k(dtb),96m(fs),-(user);spife110000.1:" \ 698 "1m(uboot),5m(kernel),128k(dtb),-(user)" 699 #endif 700 701 /* 702 * Environment 703 */ 704 705 /* 706 * Command line configuration. 707 */ 708 #define CONFIG_CMD_ERRATA 709 #define CONFIG_CMD_REGINFO 710 711 #ifdef CONFIG_PCI 712 #define CONFIG_CMD_PCI 713 #endif 714 715 /* Hash command with SHA acceleration supported in hardware */ 716 #ifdef CONFIG_FSL_CAAM 717 #define CONFIG_CMD_HASH 718 #define CONFIG_SHA_HW_ACCEL 719 #endif 720 721 /* 722 * Miscellaneous configurable options 723 */ 724 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 725 #define CONFIG_CMDLINE_EDITING /* Command-line editing */ 726 #define CONFIG_AUTO_COMPLETE /* add autocompletion support */ 727 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 728 #ifdef CONFIG_CMD_KGDB 729 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 730 #else 731 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 732 #endif 733 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) 734 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 735 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */ 736 737 /* 738 * For booting Linux, the board info and command line data 739 * have to be in the first 64 MB of memory, since this is 740 * the maximum mapped by the Linux kernel during initialization. 741 */ 742 #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial map for Linux*/ 743 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 744 745 #ifdef CONFIG_CMD_KGDB 746 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ 747 #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ 748 #endif 749 750 /* 751 * Environment Configuration 752 */ 753 #define CONFIG_ROOTPATH "/opt/nfsroot" 754 #define CONFIG_BOOTFILE "uImage" 755 #define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server */ 756 757 /* default location for tftp and bootm */ 758 #define CONFIG_LOADADDR 1000000 759 #define CONFIG_BAUDRATE 115200 760 #define __USB_PHY_TYPE utmi 761 762 #define CONFIG_EXTRA_ENV_SETTINGS \ 763 "hwconfig=fsl_ddr:" \ 764 "ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) "," \ 765 "bank_intlv=auto;" \ 766 "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\ 767 "netdev=eth0\0" \ 768 "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ 769 "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \ 770 "tftpflash=tftpboot $loadaddr $uboot && " \ 771 "protect off $ubootaddr +$filesize && " \ 772 "erase $ubootaddr +$filesize && " \ 773 "cp.b $loadaddr $ubootaddr $filesize && " \ 774 "protect on $ubootaddr +$filesize && " \ 775 "cmp.b $loadaddr $ubootaddr $filesize\0" \ 776 "consoledev=ttyS0\0" \ 777 "ramdiskaddr=2000000\0" \ 778 "ramdiskfile=t2080rdb/ramdisk.uboot\0" \ 779 "fdtaddr=1e00000\0" \ 780 "fdtfile=t2080rdb/t2080rdb.dtb\0" \ 781 "bdev=sda3\0" 782 783 /* 784 * For emulation this causes u-boot to jump to the start of the 785 * proof point app code automatically 786 */ 787 #define CONFIG_PROOF_POINTS \ 788 "setenv bootargs root=/dev/$bdev rw " \ 789 "console=$consoledev,$baudrate $othbootargs;" \ 790 "cpu 1 release 0x29000000 - - -;" \ 791 "cpu 2 release 0x29000000 - - -;" \ 792 "cpu 3 release 0x29000000 - - -;" \ 793 "cpu 4 release 0x29000000 - - -;" \ 794 "cpu 5 release 0x29000000 - - -;" \ 795 "cpu 6 release 0x29000000 - - -;" \ 796 "cpu 7 release 0x29000000 - - -;" \ 797 "go 0x29000000" 798 799 #define CONFIG_HVBOOT \ 800 "setenv bootargs config-addr=0x60000000; " \ 801 "bootm 0x01000000 - 0x00f00000" 802 803 #define CONFIG_ALU \ 804 "setenv bootargs root=/dev/$bdev rw " \ 805 "console=$consoledev,$baudrate $othbootargs;" \ 806 "cpu 1 release 0x01000000 - - -;" \ 807 "cpu 2 release 0x01000000 - - -;" \ 808 "cpu 3 release 0x01000000 - - -;" \ 809 "cpu 4 release 0x01000000 - - -;" \ 810 "cpu 5 release 0x01000000 - - -;" \ 811 "cpu 6 release 0x01000000 - - -;" \ 812 "cpu 7 release 0x01000000 - - -;" \ 813 "go 0x01000000" 814 815 #define CONFIG_LINUX \ 816 "setenv bootargs root=/dev/ram rw " \ 817 "console=$consoledev,$baudrate $othbootargs;" \ 818 "setenv ramdiskaddr 0x02000000;" \ 819 "setenv fdtaddr 0x00c00000;" \ 820 "setenv loadaddr 0x1000000;" \ 821 "bootm $loadaddr $ramdiskaddr $fdtaddr" 822 823 #define CONFIG_HDBOOT \ 824 "setenv bootargs root=/dev/$bdev rw " \ 825 "console=$consoledev,$baudrate $othbootargs;" \ 826 "tftp $loadaddr $bootfile;" \ 827 "tftp $fdtaddr $fdtfile;" \ 828 "bootm $loadaddr - $fdtaddr" 829 830 #define CONFIG_NFSBOOTCOMMAND \ 831 "setenv bootargs root=/dev/nfs rw " \ 832 "nfsroot=$serverip:$rootpath " \ 833 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 834 "console=$consoledev,$baudrate $othbootargs;" \ 835 "tftp $loadaddr $bootfile;" \ 836 "tftp $fdtaddr $fdtfile;" \ 837 "bootm $loadaddr - $fdtaddr" 838 839 #define CONFIG_RAMBOOTCOMMAND \ 840 "setenv bootargs root=/dev/ram rw " \ 841 "console=$consoledev,$baudrate $othbootargs;" \ 842 "tftp $ramdiskaddr $ramdiskfile;" \ 843 "tftp $loadaddr $bootfile;" \ 844 "tftp $fdtaddr $fdtfile;" \ 845 "bootm $loadaddr $ramdiskaddr $fdtaddr" 846 847 #define CONFIG_BOOTCOMMAND CONFIG_LINUX 848 849 #include <asm/fsl_secure_boot.h> 850 851 #endif /* __T2080RDB_H */ 852