1 /* 2 * Copyright 2014 Freescale Semiconductor, Inc. 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 /* 8 * T2080 RDB/PCIe board configuration file 9 */ 10 11 #ifndef __T2080RDB_H 12 #define __T2080RDB_H 13 14 #define CONFIG_SYS_GENERIC_BOARD 15 #define CONFIG_DISPLAY_BOARDINFO 16 #define CONFIG_T2080RDB 17 #define CONFIG_ICS307_REFCLK_HZ 25000000 /* ICS307 ref clk freq */ 18 #define CONFIG_MMC 19 #define CONFIG_SPI_FLASH 20 #define CONFIG_USB_EHCI 21 #define CONFIG_FSL_SATA_V2 22 23 /* High Level Configuration Options */ 24 #define CONFIG_PHYS_64BIT 25 #define CONFIG_BOOKE 26 #define CONFIG_E500 /* BOOKE e500 family */ 27 #define CONFIG_E500MC /* BOOKE e500mc family */ 28 #define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */ 29 #define CONFIG_MP /* support multiple processors */ 30 #define CONFIG_ENABLE_36BIT_PHYS 31 32 #ifdef CONFIG_PHYS_64BIT 33 #define CONFIG_ADDR_MAP 1 34 #define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */ 35 #endif 36 37 #define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */ 38 #define CONFIG_SYS_NUM_CPC CONFIG_NUM_DDR_CONTROLLERS 39 #define CONFIG_FSL_IFC /* Enable IFC Support */ 40 #define CONFIG_FSL_CAAM /* Enable SEC/CAAM */ 41 #define CONFIG_FSL_LAW /* Use common FSL init code */ 42 #define CONFIG_ENV_OVERWRITE 43 44 #ifdef CONFIG_RAMBOOT_PBL 45 #define CONFIG_SYS_FSL_PBL_PBI board/freescale/t208xrdb/t2080_pbi.cfg 46 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xrdb/t2080_rcw.cfg 47 48 #define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT 49 #define CONFIG_SPL_ENV_SUPPORT 50 #define CONFIG_SPL_SERIAL_SUPPORT 51 #define CONFIG_SPL_FLUSH_IMAGE 52 #define CONFIG_SPL_TARGET "u-boot-with-spl.bin" 53 #define CONFIG_SPL_LIBGENERIC_SUPPORT 54 #define CONFIG_SPL_LIBCOMMON_SUPPORT 55 #define CONFIG_SPL_I2C_SUPPORT 56 #define CONFIG_SPL_DRIVERS_MISC_SUPPORT 57 #define CONFIG_FSL_LAW /* Use common FSL init code */ 58 #define CONFIG_SYS_TEXT_BASE 0x00201000 59 #define CONFIG_SPL_TEXT_BASE 0xFFFD8000 60 #define CONFIG_SPL_PAD_TO 0x40000 61 #define CONFIG_SPL_MAX_SIZE 0x28000 62 #define RESET_VECTOR_OFFSET 0x27FFC 63 #define BOOT_PAGE_OFFSET 0x27000 64 #ifdef CONFIG_SPL_BUILD 65 #define CONFIG_SPL_SKIP_RELOCATE 66 #define CONFIG_SPL_COMMON_INIT_DDR 67 #define CONFIG_SYS_CCSR_DO_NOT_RELOCATE 68 #define CONFIG_SYS_NO_FLASH 69 #endif 70 71 #ifdef CONFIG_NAND 72 #define CONFIG_SPL_NAND_SUPPORT 73 #define CONFIG_SYS_NAND_U_BOOT_SIZE (768 << 10) 74 #define CONFIG_SYS_NAND_U_BOOT_DST 0x00200000 75 #define CONFIG_SYS_NAND_U_BOOT_START 0x00200000 76 #define CONFIG_SYS_NAND_U_BOOT_OFFS (256 << 10) 77 #define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot-nand.lds" 78 #define CONFIG_SPL_NAND_BOOT 79 #endif 80 81 #ifdef CONFIG_SPIFLASH 82 #define CONFIG_RESET_VECTOR_ADDRESS 0x200FFC 83 #define CONFIG_SPL_SPI_SUPPORT 84 #define CONFIG_SPL_SPI_FLASH_SUPPORT 85 #define CONFIG_SPL_SPI_FLASH_MINIMAL 86 #define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE (768 << 10) 87 #define CONFIG_SYS_SPI_FLASH_U_BOOT_DST (0x00200000) 88 #define CONFIG_SYS_SPI_FLASH_U_BOOT_START (0x00200000) 89 #define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS (256 << 10) 90 #define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot.lds" 91 #ifndef CONFIG_SPL_BUILD 92 #define CONFIG_SYS_MPC85XX_NO_RESETVEC 93 #endif 94 #define CONFIG_SPL_SPI_BOOT 95 #endif 96 97 #ifdef CONFIG_SDCARD 98 #define CONFIG_RESET_VECTOR_ADDRESS 0x200FFC 99 #define CONFIG_SPL_MMC_SUPPORT 100 #define CONFIG_SPL_MMC_MINIMAL 101 #define CONFIG_SYS_MMC_U_BOOT_SIZE (768 << 10) 102 #define CONFIG_SYS_MMC_U_BOOT_DST (0x00200000) 103 #define CONFIG_SYS_MMC_U_BOOT_START (0x00200000) 104 #define CONFIG_SYS_MMC_U_BOOT_OFFS (260 << 10) 105 #define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot.lds" 106 #ifndef CONFIG_SPL_BUILD 107 #define CONFIG_SYS_MPC85XX_NO_RESETVEC 108 #endif 109 #define CONFIG_SPL_MMC_BOOT 110 #endif 111 112 #endif /* CONFIG_RAMBOOT_PBL */ 113 114 #define CONFIG_SRIO_PCIE_BOOT_MASTER 115 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE 116 /* Set 1M boot space */ 117 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000) 118 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \ 119 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR) 120 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc 121 #define CONFIG_SYS_NO_FLASH 122 #endif 123 124 #ifndef CONFIG_SYS_TEXT_BASE 125 #define CONFIG_SYS_TEXT_BASE 0xeff40000 126 #endif 127 128 #ifndef CONFIG_RESET_VECTOR_ADDRESS 129 #define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc 130 #endif 131 132 /* 133 * These can be toggled for performance analysis, otherwise use default. 134 */ 135 #define CONFIG_SYS_CACHE_STASHING 136 #define CONFIG_BTB /* toggle branch predition */ 137 #define CONFIG_DDR_ECC 138 #ifdef CONFIG_DDR_ECC 139 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER 140 #define CONFIG_MEM_INIT_VALUE 0xdeadbeef 141 #endif 142 143 #ifndef CONFIG_SYS_NO_FLASH 144 #define CONFIG_FLASH_CFI_DRIVER 145 #define CONFIG_SYS_FLASH_CFI 146 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 147 #endif 148 149 #if defined(CONFIG_SPIFLASH) 150 #define CONFIG_SYS_EXTRA_ENV_RELOC 151 #define CONFIG_ENV_IS_IN_SPI_FLASH 152 #define CONFIG_ENV_SPI_BUS 0 153 #define CONFIG_ENV_SPI_CS 0 154 #define CONFIG_ENV_SPI_MAX_HZ 10000000 155 #define CONFIG_ENV_SPI_MODE 0 156 #define CONFIG_ENV_SIZE 0x2000 /* 8KB */ 157 #define CONFIG_ENV_OFFSET 0x100000 /* 1MB */ 158 #define CONFIG_ENV_SECT_SIZE 0x10000 159 #elif defined(CONFIG_SDCARD) 160 #define CONFIG_SYS_EXTRA_ENV_RELOC 161 #define CONFIG_ENV_IS_IN_MMC 162 #define CONFIG_SYS_MMC_ENV_DEV 0 163 #define CONFIG_ENV_SIZE 0x2000 164 #define CONFIG_ENV_OFFSET (512 * 0x800) 165 #elif defined(CONFIG_NAND) 166 #define CONFIG_SYS_EXTRA_ENV_RELOC 167 #define CONFIG_ENV_IS_IN_NAND 168 #define CONFIG_ENV_SIZE 0x2000 169 #define CONFIG_ENV_OFFSET (2 * CONFIG_SYS_NAND_BLOCK_SIZE) 170 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) 171 #define CONFIG_ENV_IS_IN_REMOTE 172 #define CONFIG_ENV_ADDR 0xffe20000 173 #define CONFIG_ENV_SIZE 0x2000 174 #elif defined(CONFIG_ENV_IS_NOWHERE) 175 #define CONFIG_ENV_SIZE 0x2000 176 #else 177 #define CONFIG_ENV_IS_IN_FLASH 178 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) 179 #define CONFIG_ENV_SIZE 0x2000 180 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ 181 #endif 182 183 #ifndef __ASSEMBLY__ 184 unsigned long get_board_sys_clk(void); 185 unsigned long get_board_ddr_clk(void); 186 #endif 187 188 #define CONFIG_SYS_CLK_FREQ 66660000 189 #define CONFIG_DDR_CLK_FREQ 133330000 190 191 /* 192 * Config the L3 Cache as L3 SRAM 193 */ 194 #define CONFIG_SYS_INIT_L3_ADDR 0xFFFC0000 195 #define CONFIG_SYS_L3_SIZE (512 << 10) 196 #define CONFIG_SPL_GD_ADDR (CONFIG_SYS_INIT_L3_ADDR + 32 * 1024) 197 #ifdef CONFIG_RAMBOOT_PBL 198 #define CONFIG_ENV_ADDR (CONFIG_SPL_GD_ADDR + 4 * 1024) 199 #endif 200 #define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SPL_GD_ADDR + 12 * 1024) 201 #define CONFIG_SPL_RELOC_MALLOC_SIZE (50 << 10) 202 #define CONFIG_SPL_RELOC_STACK (CONFIG_SPL_GD_ADDR + 64 * 1024) 203 #define CONFIG_SPL_RELOC_STACK_SIZE (22 << 10) 204 205 #define CONFIG_SYS_DCSRBAR 0xf0000000 206 #define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull 207 208 /* EEPROM */ 209 #define CONFIG_ID_EEPROM 210 #define CONFIG_SYS_I2C_EEPROM_NXID 211 #define CONFIG_SYS_EEPROM_BUS_NUM 0 212 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 213 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 214 215 /* 216 * DDR Setup 217 */ 218 #define CONFIG_VERY_BIG_RAM 219 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 220 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 221 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 222 #define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR) 223 #define CONFIG_DDR_SPD 224 #define CONFIG_SYS_FSL_DDR3 225 #undef CONFIG_FSL_DDR_INTERACTIVE 226 #define CONFIG_SYS_SPD_BUS_NUM 0 227 #define CONFIG_SYS_SDRAM_SIZE 2048 /* for fixed parameter use */ 228 #define SPD_EEPROM_ADDRESS1 0x51 229 #define SPD_EEPROM_ADDRESS2 0x52 230 #define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1 231 #define CTRL_INTLV_PREFERED cacheline 232 233 /* 234 * IFC Definitions 235 */ 236 #define CONFIG_SYS_FLASH_BASE 0xe8000000 237 #define CONFIG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CONFIG_SYS_FLASH_BASE) 238 #define CONFIG_SYS_NOR0_CSPR_EXT (0xf) 239 #define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \ 240 CSPR_PORT_SIZE_16 | \ 241 CSPR_MSEL_NOR | \ 242 CSPR_V) 243 #define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024) 244 245 /* NOR Flash Timing Params */ 246 #define CONFIG_SYS_NOR_CSOR CSOR_NAND_TRHZ_80 247 248 #define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \ 249 FTIM0_NOR_TEADC(0x5) | \ 250 FTIM0_NOR_TEAHC(0x5)) 251 #define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \ 252 FTIM1_NOR_TRAD_NOR(0x1A) |\ 253 FTIM1_NOR_TSEQRAD_NOR(0x13)) 254 #define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \ 255 FTIM2_NOR_TCH(0x4) | \ 256 FTIM2_NOR_TWPH(0x0E) | \ 257 FTIM2_NOR_TWP(0x1c)) 258 #define CONFIG_SYS_NOR_FTIM3 0x0 259 260 #define CONFIG_SYS_FLASH_QUIET_TEST 261 #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ 262 263 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 264 #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ 265 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 266 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 267 #define CONFIG_SYS_FLASH_EMPTY_INFO 268 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS } 269 270 /* CPLD on IFC */ 271 #define CONFIG_SYS_CPLD_BASE 0xffdf0000 272 #define CONFIG_SYS_CPLD_BASE_PHYS (0xf00000000ull | CONFIG_SYS_CPLD_BASE) 273 #define CONFIG_SYS_CSPR2_EXT (0xf) 274 #define CONFIG_SYS_CSPR2 (CSPR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE) \ 275 | CSPR_PORT_SIZE_8 \ 276 | CSPR_MSEL_GPCM \ 277 | CSPR_V) 278 #define CONFIG_SYS_AMASK2 IFC_AMASK(64*1024) 279 #define CONFIG_SYS_CSOR2 0x0 280 281 /* CPLD Timing parameters for IFC CS2 */ 282 #define CONFIG_SYS_CS2_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \ 283 FTIM0_GPCM_TEADC(0x0e) | \ 284 FTIM0_GPCM_TEAHC(0x0e)) 285 #define CONFIG_SYS_CS2_FTIM1 (FTIM1_GPCM_TACO(0x0e) | \ 286 FTIM1_GPCM_TRAD(0x1f)) 287 #define CONFIG_SYS_CS2_FTIM2 (FTIM2_GPCM_TCS(0x0e) | \ 288 FTIM2_GPCM_TCH(0x8) | \ 289 FTIM2_GPCM_TWP(0x1f)) 290 #define CONFIG_SYS_CS2_FTIM3 0x0 291 292 /* NAND Flash on IFC */ 293 #define CONFIG_NAND_FSL_IFC 294 #define CONFIG_SYS_NAND_BASE 0xff800000 295 #define CONFIG_SYS_NAND_BASE_PHYS (0xf00000000ull | CONFIG_SYS_NAND_BASE) 296 297 #define CONFIG_SYS_NAND_CSPR_EXT (0xf) 298 #define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ 299 | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \ 300 | CSPR_MSEL_NAND /* MSEL = NAND */ \ 301 | CSPR_V) 302 #define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024) 303 304 #define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \ 305 | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \ 306 | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \ 307 | CSOR_NAND_RAL_3 /* RAL = 2Byes */ \ 308 | CSOR_NAND_PGS_2K /* Page Size = 2K */\ 309 | CSOR_NAND_SPRZ_64 /* Spare size = 64 */\ 310 | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/ 311 312 #define CONFIG_SYS_NAND_ONFI_DETECTION 313 314 /* ONFI NAND Flash mode0 Timing Params */ 315 #define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \ 316 FTIM0_NAND_TWP(0x18) | \ 317 FTIM0_NAND_TWCHT(0x07) | \ 318 FTIM0_NAND_TWH(0x0a)) 319 #define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \ 320 FTIM1_NAND_TWBE(0x39) | \ 321 FTIM1_NAND_TRR(0x0e) | \ 322 FTIM1_NAND_TRP(0x18)) 323 #define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \ 324 FTIM2_NAND_TREH(0x0a) | \ 325 FTIM2_NAND_TWHRE(0x1e)) 326 #define CONFIG_SYS_NAND_FTIM3 0x0 327 328 #define CONFIG_SYS_NAND_DDR_LAW 11 329 #define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } 330 #define CONFIG_SYS_MAX_NAND_DEVICE 1 331 #define CONFIG_MTD_NAND_VERIFY_WRITE 332 #define CONFIG_CMD_NAND 333 #define CONFIG_SYS_NAND_BLOCK_SIZE (512 * 1024) 334 335 #if defined(CONFIG_NAND) 336 #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT 337 #define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR 338 #define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK 339 #define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR 340 #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0 341 #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1 342 #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2 343 #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3 344 #define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR0_CSPR_EXT 345 #define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR0_CSPR 346 #define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK 347 #define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR 348 #define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0 349 #define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1 350 #define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2 351 #define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3 352 #else 353 #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT 354 #define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR 355 #define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK 356 #define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR 357 #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0 358 #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1 359 #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2 360 #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3 361 #define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NAND_CSPR_EXT 362 #define CONFIG_SYS_CSPR1 CONFIG_SYS_NAND_CSPR 363 #define CONFIG_SYS_AMASK1 CONFIG_SYS_NAND_AMASK 364 #define CONFIG_SYS_CSOR1 CONFIG_SYS_NAND_CSOR 365 #define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NAND_FTIM0 366 #define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NAND_FTIM1 367 #define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NAND_FTIM2 368 #define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NAND_FTIM3 369 #endif 370 371 #if defined(CONFIG_RAMBOOT_PBL) 372 #define CONFIG_SYS_RAMBOOT 373 #endif 374 375 #ifdef CONFIG_SPL_BUILD 376 #define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE 377 #else 378 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 379 #endif 380 381 #define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */ 382 #define CONFIG_MISC_INIT_R 383 #define CONFIG_HWCONFIG 384 385 /* define to use L1 as initial stack */ 386 #define CONFIG_L1_INIT_RAM 387 #define CONFIG_SYS_INIT_RAM_LOCK 388 #define CONFIG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */ 389 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf 390 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW 0xfe0ec000 391 /* The assembler doesn't like typecast */ 392 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \ 393 ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \ 394 CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW) 395 #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 396 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ 397 GENERATED_GBL_DATA_SIZE) 398 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 399 #define CONFIG_SYS_MONITOR_LEN (768 * 1024) 400 #define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024) 401 402 /* 403 * Serial Port 404 */ 405 #define CONFIG_CONS_INDEX 1 406 #define CONFIG_SYS_NS16550 407 #define CONFIG_SYS_NS16550_SERIAL 408 #define CONFIG_SYS_NS16550_REG_SIZE 1 409 #define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2) 410 #define CONFIG_SYS_BAUDRATE_TABLE \ 411 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} 412 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500) 413 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600) 414 #define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500) 415 #define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600) 416 417 /* Use the HUSH parser */ 418 #define CONFIG_SYS_HUSH_PARSER 419 #define CONFIG_SYS_PROMPT_HUSH_PS2 "> " 420 421 /* pass open firmware flat tree */ 422 #define CONFIG_OF_LIBFDT 423 #define CONFIG_OF_BOARD_SETUP 424 #define CONFIG_OF_STDOUT_VIA_ALIAS 425 426 /* new uImage format support */ 427 #define CONFIG_FIT 428 #define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ 429 430 /* 431 * I2C 432 */ 433 #define CONFIG_SYS_I2C 434 #define CONFIG_SYS_I2C_FSL 435 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 436 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F 437 #define CONFIG_SYS_FSL_I2C3_SLAVE 0x7F 438 #define CONFIG_SYS_FSL_I2C4_SLAVE 0x7F 439 #define CONFIG_SYS_FSL_I2C_OFFSET 0x118000 440 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100 441 #define CONFIG_SYS_FSL_I2C3_OFFSET 0x119000 442 #define CONFIG_SYS_FSL_I2C4_OFFSET 0x119100 443 #define CONFIG_SYS_FSL_I2C_SPEED 100000 444 #define CONFIG_SYS_FSL_I2C2_SPEED 100000 445 #define CONFIG_SYS_FSL_I2C3_SPEED 100000 446 #define CONFIG_SYS_FSL_I2C4_SPEED 100000 447 #define I2C_MUX_PCA_ADDR_PRI 0x77 /* I2C bus multiplexer,primary */ 448 #define I2C_MUX_PCA_ADDR_SEC1 0x75 /* I2C bus multiplexer,secondary 1 */ 449 #define I2C_MUX_PCA_ADDR_SEC2 0x76 /* I2C bus multiplexer,secondary 2 */ 450 #define I2C_MUX_CH_DEFAULT 0x8 451 452 453 /* 454 * RapidIO 455 */ 456 #define CONFIG_SYS_SRIO1_MEM_VIRT 0xa0000000 457 #define CONFIG_SYS_SRIO1_MEM_PHYS 0xc20000000ull 458 #define CONFIG_SYS_SRIO1_MEM_SIZE 0x10000000 /* 256M */ 459 #define CONFIG_SYS_SRIO2_MEM_VIRT 0xb0000000 460 #define CONFIG_SYS_SRIO2_MEM_PHYS 0xc30000000ull 461 #define CONFIG_SYS_SRIO2_MEM_SIZE 0x10000000 /* 256M */ 462 /* 463 * for slave u-boot IMAGE instored in master memory space, 464 * PHYS must be aligned based on the SIZE 465 */ 466 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull 467 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull 468 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x100000 /* 1M */ 469 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull 470 /* 471 * for slave UCODE and ENV instored in master memory space, 472 * PHYS must be aligned based on the SIZE 473 */ 474 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull 475 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull 476 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */ 477 478 /* slave core release by master*/ 479 #define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4 480 #define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */ 481 482 /* 483 * SRIO_PCIE_BOOT - SLAVE 484 */ 485 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE 486 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000 487 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \ 488 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR) 489 #endif 490 491 /* 492 * eSPI - Enhanced SPI 493 */ 494 #ifdef CONFIG_SPI_FLASH 495 #define CONFIG_FSL_ESPI 496 #define CONFIG_SPI_FLASH_STMICRO 497 #define CONFIG_SPI_FLASH_BAR 498 #define CONFIG_CMD_SF 499 #define CONFIG_SF_DEFAULT_SPEED 10000000 500 #define CONFIG_SF_DEFAULT_MODE 0 501 #endif 502 503 /* 504 * General PCI 505 * Memory space is mapped 1-1, but I/O space must start from 0. 506 */ 507 #define CONFIG_PCI /* Enable PCI/PCIE */ 508 #define CONFIG_PCIE1 /* PCIE controler 1 */ 509 #define CONFIG_PCIE2 /* PCIE controler 2 */ 510 #define CONFIG_PCIE3 /* PCIE controler 3 */ 511 #define CONFIG_PCIE4 /* PCIE controler 4 */ 512 #define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ 513 #define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ 514 /* controller 1, direct to uli, tgtid 3, Base address 20000 */ 515 #define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 516 #define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 517 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull 518 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ 519 #define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000 520 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 521 #define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull 522 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ 523 524 /* controller 2, Slot 2, tgtid 2, Base address 201000 */ 525 #define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 526 #define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000 527 #define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull 528 #define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */ 529 #define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000 530 #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 531 #define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull 532 #define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ 533 534 /* controller 3, Slot 1, tgtid 1, Base address 202000 */ 535 #define CONFIG_SYS_PCIE3_MEM_VIRT 0xb0000000 536 #define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000 537 #define CONFIG_SYS_PCIE3_MEM_PHYS 0xc30000000ull 538 #define CONFIG_SYS_PCIE3_MEM_SIZE 0x10000000 /* 256M */ 539 #define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000 540 #define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 541 #define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull 542 #define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */ 543 544 /* controller 4, Base address 203000 */ 545 #define CONFIG_SYS_PCIE4_MEM_VIRT 0xc0000000 546 #define CONFIG_SYS_PCIE4_MEM_BUS 0xe0000000 547 #define CONFIG_SYS_PCIE4_MEM_PHYS 0xc40000000ull 548 #define CONFIG_SYS_PCIE4_MEM_SIZE 0x10000000 /* 256M */ 549 #define CONFIG_SYS_PCIE4_IO_BUS 0x00000000 550 #define CONFIG_SYS_PCIE4_IO_PHYS 0xff8030000ull 551 #define CONFIG_SYS_PCIE4_IO_SIZE 0x00010000 /* 64k */ 552 553 #ifdef CONFIG_PCI 554 #define CONFIG_PCI_INDIRECT_BRIDGE 555 #define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata LSZ ADD */ 556 #define CONFIG_NET_MULTI 557 #define CONFIG_E1000 558 #define CONFIG_PCI_PNP /* do pci plug-and-play */ 559 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 560 #define CONFIG_DOS_PARTITION 561 #endif 562 563 /* Qman/Bman */ 564 #ifndef CONFIG_NOBQFMAN 565 #define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */ 566 #define CONFIG_SYS_BMAN_NUM_PORTALS 18 567 #define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000 568 #define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull 569 #define CONFIG_SYS_BMAN_MEM_SIZE 0x02000000 570 #define CONFIG_SYS_QMAN_NUM_PORTALS 18 571 #define CONFIG_SYS_QMAN_MEM_BASE 0xf6000000 572 #define CONFIG_SYS_QMAN_MEM_PHYS 0xff6000000ull 573 #define CONFIG_SYS_QMAN_MEM_SIZE 0x02000000 574 575 #define CONFIG_SYS_DPAA_FMAN 576 #define CONFIG_SYS_DPAA_PME 577 #define CONFIG_SYS_PMAN 578 #define CONFIG_SYS_DPAA_DCE 579 #define CONFIG_SYS_DPAA_RMAN /* RMan */ 580 #define CONFIG_SYS_INTERLAKEN 581 582 /* Default address of microcode for the Linux Fman driver */ 583 #if defined(CONFIG_SPIFLASH) 584 /* 585 * env is stored at 0x100000, sector size is 0x10000, ucode is stored after 586 * env, so we got 0x110000. 587 */ 588 #define CONFIG_SYS_QE_FW_IN_SPIFLASH 589 #define CONFIG_SYS_CORTINA_FW_IN_SPIFLASH 590 #define CONFIG_SYS_FMAN_FW_ADDR 0x110000 591 #define CONFIG_CORTINA_FW_ADDR 0x120000 592 593 #elif defined(CONFIG_SDCARD) 594 /* 595 * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is 596 * about 1MB (2048 blocks), Env is stored after the image, and the env size is 597 * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080. 598 */ 599 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC 600 #define CONFIG_SYS_CORTINA_FW_IN_MMC 601 #define CONFIG_SYS_FMAN_FW_ADDR (512 * 0x820) 602 #define CONFIG_CORTINA_FW_ADDR (512 * 0x8a0) 603 604 #elif defined(CONFIG_NAND) 605 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND 606 #define CONFIG_SYS_CORTINA_FW_IN_NAND 607 #define CONFIG_SYS_FMAN_FW_ADDR (3 * CONFIG_SYS_NAND_BLOCK_SIZE) 608 #define CONFIG_CORTINA_FW_ADDR (4 * CONFIG_SYS_NAND_BLOCK_SIZE) 609 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) 610 /* 611 * Slave has no ucode locally, it can fetch this from remote. When implementing 612 * in two corenet boards, slave's ucode could be stored in master's memory 613 * space, the address can be mapped from slave TLB->slave LAW-> 614 * slave SRIO or PCIE outbound window->master inbound window-> 615 * master LAW->the ucode address in master's memory space. 616 */ 617 #define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE 618 #define CONFIG_SYS_CORTINA_FW_IN_REMOTE 619 #define CONFIG_SYS_FMAN_FW_ADDR 0xFFE00000 620 #define CONFIG_CORTINA_FW_ADDR 0xFFE10000 621 #else 622 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR 623 #define CONFIG_SYS_CORTINA_FW_IN_NOR 624 #define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000 625 #define CONFIG_CORTINA_FW_ADDR 0xEFE00000 626 #endif 627 #define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 628 #define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) 629 #endif /* CONFIG_NOBQFMAN */ 630 631 #ifdef CONFIG_SYS_DPAA_FMAN 632 #define CONFIG_FMAN_ENET 633 #define CONFIG_PHYLIB_10G 634 #define CONFIG_PHY_CORTINA 635 #define CONFIG_PHY_AQ1202 636 #define CONFIG_PHY_REALTEK 637 #define CONFIG_CORTINA_FW_LENGTH 0x40000 638 #define RGMII_PHY1_ADDR 0x01 /* RealTek RTL8211E */ 639 #define RGMII_PHY2_ADDR 0x02 640 #define CORTINA_PHY_ADDR1 0x0c /* Cortina CS4315 */ 641 #define CORTINA_PHY_ADDR2 0x0d 642 #define FM1_10GEC3_PHY_ADDR 0x00 /* Aquantia AQ1202 10G Base-T */ 643 #define FM1_10GEC4_PHY_ADDR 0x01 644 #endif 645 646 647 #ifdef CONFIG_FMAN_ENET 648 #define CONFIG_MII /* MII PHY management */ 649 #define CONFIG_ETHPRIME "FM1@DTSEC3" 650 #define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ 651 #endif 652 653 /* 654 * SATA 655 */ 656 #ifdef CONFIG_FSL_SATA_V2 657 #define CONFIG_LIBATA 658 #define CONFIG_FSL_SATA 659 #define CONFIG_SYS_SATA_MAX_DEVICE 2 660 #define CONFIG_SATA1 661 #define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR 662 #define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA 663 #define CONFIG_SATA2 664 #define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR 665 #define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA 666 #define CONFIG_LBA48 667 #define CONFIG_CMD_SATA 668 #define CONFIG_DOS_PARTITION 669 #define CONFIG_CMD_EXT2 670 #endif 671 672 /* 673 * USB 674 */ 675 #ifdef CONFIG_USB_EHCI 676 #define CONFIG_CMD_USB 677 #define CONFIG_USB_STORAGE 678 #define CONFIG_USB_EHCI_FSL 679 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET 680 #define CONFIG_CMD_EXT2 681 #define CONFIG_HAS_FSL_DR_USB 682 #endif 683 684 /* 685 * SDHC 686 */ 687 #ifdef CONFIG_MMC 688 #define CONFIG_CMD_MMC 689 #define CONFIG_FSL_ESDHC 690 #define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR 691 #define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT 692 #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33 693 #define CONFIG_GENERIC_MMC 694 #define CONFIG_CMD_EXT2 695 #define CONFIG_CMD_FAT 696 #define CONFIG_DOS_PARTITION 697 #endif 698 699 /* 700 * Dynamic MTD Partition support with mtdparts 701 */ 702 #ifndef CONFIG_SYS_NO_FLASH 703 #define CONFIG_MTD_DEVICE 704 #define CONFIG_MTD_PARTITIONS 705 #define CONFIG_CMD_MTDPARTS 706 #define CONFIG_FLASH_CFI_MTD 707 #define MTDIDS_DEFAULT "nor0=fe8000000.nor,nand0=fff800000.flash," \ 708 "spi0=spife110000.1" 709 #define MTDPARTS_DEFAULT "mtdparts=fe8000000.nor:1m(uboot),5m(kernel)," \ 710 "128k(dtb),96m(fs),-(user);fff800000.flash:1m(uboot)," \ 711 "5m(kernel),128k(dtb),96m(fs),-(user);spife110000.1:" \ 712 "1m(uboot),5m(kernel),128k(dtb),-(user)" 713 #endif 714 715 /* 716 * Environment 717 */ 718 719 /* 720 * Command line configuration. 721 */ 722 #include <config_cmd_default.h> 723 724 #define CONFIG_CMD_DHCP 725 #define CONFIG_CMD_ELF 726 #define CONFIG_CMD_ERRATA 727 #define CONFIG_CMD_MII 728 #define CONFIG_CMD_I2C 729 #define CONFIG_CMD_PING 730 #define CONFIG_CMD_ECHO 731 #define CONFIG_CMD_SETEXPR 732 #define CONFIG_CMD_REGINFO 733 #define CONFIG_CMD_BDI 734 735 #ifdef CONFIG_PCI 736 #define CONFIG_CMD_PCI 737 #define CONFIG_CMD_NET 738 #endif 739 740 /* Hash command with SHA acceleration supported in hardware */ 741 #ifdef CONFIG_FSL_CAAM 742 #define CONFIG_CMD_HASH 743 #define CONFIG_SHA_HW_ACCEL 744 #endif 745 746 /* 747 * Miscellaneous configurable options 748 */ 749 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 750 #define CONFIG_CMDLINE_EDITING /* Command-line editing */ 751 #define CONFIG_AUTO_COMPLETE /* add autocompletion support */ 752 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 753 #ifdef CONFIG_CMD_KGDB 754 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 755 #else 756 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 757 #endif 758 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) 759 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 760 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */ 761 762 /* 763 * For booting Linux, the board info and command line data 764 * have to be in the first 64 MB of memory, since this is 765 * the maximum mapped by the Linux kernel during initialization. 766 */ 767 #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial map for Linux*/ 768 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 769 770 #ifdef CONFIG_CMD_KGDB 771 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ 772 #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ 773 #endif 774 775 /* 776 * Environment Configuration 777 */ 778 #define CONFIG_ROOTPATH "/opt/nfsroot" 779 #define CONFIG_BOOTFILE "uImage" 780 #define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server */ 781 782 /* default location for tftp and bootm */ 783 #define CONFIG_LOADADDR 1000000 784 #define CONFIG_BAUDRATE 115200 785 #define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ 786 #define __USB_PHY_TYPE utmi 787 788 #define CONFIG_EXTRA_ENV_SETTINGS \ 789 "hwconfig=fsl_ddr:" \ 790 "ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) "," \ 791 "bank_intlv=auto;" \ 792 "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\ 793 "netdev=eth0\0" \ 794 "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ 795 "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \ 796 "tftpflash=tftpboot $loadaddr $uboot && " \ 797 "protect off $ubootaddr +$filesize && " \ 798 "erase $ubootaddr +$filesize && " \ 799 "cp.b $loadaddr $ubootaddr $filesize && " \ 800 "protect on $ubootaddr +$filesize && " \ 801 "cmp.b $loadaddr $ubootaddr $filesize\0" \ 802 "consoledev=ttyS0\0" \ 803 "ramdiskaddr=2000000\0" \ 804 "ramdiskfile=t2080rdb/ramdisk.uboot\0" \ 805 "fdtaddr=c00000\0" \ 806 "fdtfile=t2080rdb/t2080rdb.dtb\0" \ 807 "bdev=sda3\0" 808 809 /* 810 * For emulation this causes u-boot to jump to the start of the 811 * proof point app code automatically 812 */ 813 #define CONFIG_PROOF_POINTS \ 814 "setenv bootargs root=/dev/$bdev rw " \ 815 "console=$consoledev,$baudrate $othbootargs;" \ 816 "cpu 1 release 0x29000000 - - -;" \ 817 "cpu 2 release 0x29000000 - - -;" \ 818 "cpu 3 release 0x29000000 - - -;" \ 819 "cpu 4 release 0x29000000 - - -;" \ 820 "cpu 5 release 0x29000000 - - -;" \ 821 "cpu 6 release 0x29000000 - - -;" \ 822 "cpu 7 release 0x29000000 - - -;" \ 823 "go 0x29000000" 824 825 #define CONFIG_HVBOOT \ 826 "setenv bootargs config-addr=0x60000000; " \ 827 "bootm 0x01000000 - 0x00f00000" 828 829 #define CONFIG_ALU \ 830 "setenv bootargs root=/dev/$bdev rw " \ 831 "console=$consoledev,$baudrate $othbootargs;" \ 832 "cpu 1 release 0x01000000 - - -;" \ 833 "cpu 2 release 0x01000000 - - -;" \ 834 "cpu 3 release 0x01000000 - - -;" \ 835 "cpu 4 release 0x01000000 - - -;" \ 836 "cpu 5 release 0x01000000 - - -;" \ 837 "cpu 6 release 0x01000000 - - -;" \ 838 "cpu 7 release 0x01000000 - - -;" \ 839 "go 0x01000000" 840 841 #define CONFIG_LINUX \ 842 "setenv bootargs root=/dev/ram rw " \ 843 "console=$consoledev,$baudrate $othbootargs;" \ 844 "setenv ramdiskaddr 0x02000000;" \ 845 "setenv fdtaddr 0x00c00000;" \ 846 "setenv loadaddr 0x1000000;" \ 847 "bootm $loadaddr $ramdiskaddr $fdtaddr" 848 849 #define CONFIG_HDBOOT \ 850 "setenv bootargs root=/dev/$bdev rw " \ 851 "console=$consoledev,$baudrate $othbootargs;" \ 852 "tftp $loadaddr $bootfile;" \ 853 "tftp $fdtaddr $fdtfile;" \ 854 "bootm $loadaddr - $fdtaddr" 855 856 #define CONFIG_NFSBOOTCOMMAND \ 857 "setenv bootargs root=/dev/nfs rw " \ 858 "nfsroot=$serverip:$rootpath " \ 859 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 860 "console=$consoledev,$baudrate $othbootargs;" \ 861 "tftp $loadaddr $bootfile;" \ 862 "tftp $fdtaddr $fdtfile;" \ 863 "bootm $loadaddr - $fdtaddr" 864 865 #define CONFIG_RAMBOOTCOMMAND \ 866 "setenv bootargs root=/dev/ram rw " \ 867 "console=$consoledev,$baudrate $othbootargs;" \ 868 "tftp $ramdiskaddr $ramdiskfile;" \ 869 "tftp $loadaddr $bootfile;" \ 870 "tftp $fdtaddr $fdtfile;" \ 871 "bootm $loadaddr $ramdiskaddr $fdtaddr" 872 873 #define CONFIG_BOOTCOMMAND CONFIG_LINUX 874 875 #ifdef CONFIG_SECURE_BOOT 876 #include <asm/fsl_secure_boot.h> 877 #define CONFIG_CMD_BLOB 878 #undef CONFIG_CMD_USB 879 #endif 880 881 #endif /* __T2080RDB_H */ 882