1 /* 2 * Copyright 2011-2013 Freescale Semiconductor, Inc. 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 /* 8 * T2080/T2081 QDS board configuration file 9 */ 10 11 #ifndef __T208xQDS_H 12 #define __T208xQDS_H 13 14 #define CONFIG_ICS307_REFCLK_HZ 25000000 /* ICS307 ref clk freq */ 15 #define CONFIG_MMC 16 #define CONFIG_SPI_FLASH 17 #define CONFIG_USB_EHCI 18 #if defined(CONFIG_PPC_T2080) 19 #define CONFIG_T2080QDS 20 #define CONFIG_FSL_SATA_V2 21 #define CONFIG_SYS_SRIO /* Enable Serial RapidIO Support */ 22 #define CONFIG_SRIO1 /* SRIO port 1 */ 23 #define CONFIG_SRIO2 /* SRIO port 2 */ 24 #elif defined(CONFIG_PPC_T2081) 25 #define CONFIG_T2081QDS 26 #endif 27 28 /* High Level Configuration Options */ 29 #define CONFIG_PHYS_64BIT 30 #define CONFIG_BOOKE 31 #define CONFIG_E500 /* BOOKE e500 family */ 32 #define CONFIG_E500MC /* BOOKE e500mc family */ 33 #define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */ 34 #define CONFIG_MP /* support multiple processors */ 35 #define CONFIG_ENABLE_36BIT_PHYS 36 37 #ifdef CONFIG_PHYS_64BIT 38 #define CONFIG_ADDR_MAP 1 39 #define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */ 40 #endif 41 42 #define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */ 43 #define CONFIG_SYS_NUM_CPC CONFIG_NUM_DDR_CONTROLLERS 44 #define CONFIG_FSL_IFC /* Enable IFC Support */ 45 #define CONFIG_FSL_LAW /* Use common FSL init code */ 46 #define CONFIG_ENV_OVERWRITE 47 48 #ifdef CONFIG_RAMBOOT_PBL 49 #define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE 50 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc 51 #define CONFIG_SYS_FSL_PBL_PBI $(SRCTREE)/board/freescale/t208xqds/t208x_pbi.cfg 52 #if defined(CONFIG_PPC_T2080) 53 #define CONFIG_SYS_FSL_PBL_RCW $(SRCTREE)/board/freescale/t208xqds/t2080_rcw.cfg 54 #elif defined(CONFIG_PPC_T2081) 55 #define CONFIG_SYS_FSL_PBL_RCW $(SRCTREE)/board/freescale/t208xqds/t2081_rcw.cfg 56 #endif 57 #endif 58 59 #define CONFIG_SRIO_PCIE_BOOT_MASTER 60 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE 61 /* Set 1M boot space */ 62 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000) 63 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \ 64 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR) 65 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc 66 #define CONFIG_SYS_NO_FLASH 67 #endif 68 69 #ifndef CONFIG_SYS_TEXT_BASE 70 #define CONFIG_SYS_TEXT_BASE 0xeff40000 71 #endif 72 73 #ifndef CONFIG_RESET_VECTOR_ADDRESS 74 #define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc 75 #endif 76 77 /* 78 * These can be toggled for performance analysis, otherwise use default. 79 */ 80 #define CONFIG_SYS_CACHE_STASHING 81 #define CONFIG_BTB /* toggle branch predition */ 82 #define CONFIG_DDR_ECC 83 #ifdef CONFIG_DDR_ECC 84 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER 85 #define CONFIG_MEM_INIT_VALUE 0xdeadbeef 86 #endif 87 88 #ifdef CONFIG_SYS_NO_FLASH 89 #if !defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) && !defined(CONFIG_RAMBOOT_PBL) 90 #define CONFIG_ENV_IS_NOWHERE 91 #endif 92 #else 93 #define CONFIG_FLASH_CFI_DRIVER 94 #define CONFIG_SYS_FLASH_CFI 95 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 96 #endif 97 98 #if defined(CONFIG_SPIFLASH) 99 #define CONFIG_SYS_EXTRA_ENV_RELOC 100 #define CONFIG_ENV_IS_IN_SPI_FLASH 101 #define CONFIG_ENV_SPI_BUS 0 102 #define CONFIG_ENV_SPI_CS 0 103 #define CONFIG_ENV_SPI_MAX_HZ 10000000 104 #define CONFIG_ENV_SPI_MODE 0 105 #define CONFIG_ENV_SIZE 0x2000 /* 8KB */ 106 #define CONFIG_ENV_OFFSET 0x100000 /* 1MB */ 107 #define CONFIG_ENV_SECT_SIZE 0x10000 108 #elif defined(CONFIG_SDCARD) 109 #define CONFIG_SYS_EXTRA_ENV_RELOC 110 #define CONFIG_ENV_IS_IN_MMC 111 #define CONFIG_SYS_MMC_ENV_DEV 0 112 #define CONFIG_ENV_SIZE 0x2000 113 #define CONFIG_ENV_OFFSET (512 * 1658) 114 #elif defined(CONFIG_NAND) 115 #define CONFIG_SYS_EXTRA_ENV_RELOC 116 #define CONFIG_ENV_IS_IN_NAND 117 #define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE 118 #define CONFIG_ENV_OFFSET (7 * CONFIG_SYS_NAND_BLOCK_SIZE) 119 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) 120 #define CONFIG_ENV_IS_IN_REMOTE 121 #define CONFIG_ENV_ADDR 0xffe20000 122 #define CONFIG_ENV_SIZE 0x2000 123 #elif defined(CONFIG_ENV_IS_NOWHERE) 124 #define CONFIG_ENV_SIZE 0x2000 125 #else 126 #define CONFIG_ENV_IS_IN_FLASH 127 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) 128 #define CONFIG_ENV_SIZE 0x2000 129 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ 130 #endif 131 132 #ifndef __ASSEMBLY__ 133 unsigned long get_board_sys_clk(void); 134 unsigned long get_board_ddr_clk(void); 135 #endif 136 137 #define CONFIG_SYS_CLK_FREQ get_board_sys_clk() 138 #define CONFIG_DDR_CLK_FREQ get_board_ddr_clk() 139 140 /* 141 * Config the L3 Cache as L3 SRAM 142 */ 143 #define CONFIG_SYS_INIT_L3_ADDR CONFIG_RAMBOOT_TEXT_BASE 144 145 #define CONFIG_SYS_DCSRBAR 0xf0000000 146 #define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull 147 148 /* EEPROM */ 149 #define CONFIG_ID_EEPROM 150 #define CONFIG_SYS_I2C_EEPROM_NXID 151 #define CONFIG_SYS_EEPROM_BUS_NUM 0 152 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 153 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 154 155 /* 156 * DDR Setup 157 */ 158 #define CONFIG_VERY_BIG_RAM 159 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 160 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 161 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 162 #define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR) 163 #define CONFIG_DDR_SPD 164 #define CONFIG_SYS_FSL_DDR3 165 #undef CONFIG_FSL_DDR_INTERACTIVE 166 #define CONFIG_SYS_SPD_BUS_NUM 0 167 #define CONFIG_SYS_SDRAM_SIZE 2048 /* for fixed parameter use */ 168 #define SPD_EEPROM_ADDRESS1 0x51 169 #define SPD_EEPROM_ADDRESS2 0x52 170 #define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1 171 #define CTRL_INTLV_PREFERED cacheline 172 173 /* 174 * IFC Definitions 175 */ 176 #define CONFIG_SYS_FLASH_BASE 0xe0000000 177 #define CONFIG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CONFIG_SYS_FLASH_BASE) 178 #define CONFIG_SYS_NOR0_CSPR_EXT (0xf) 179 #define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS \ 180 + 0x8000000) | \ 181 CSPR_PORT_SIZE_16 | \ 182 CSPR_MSEL_NOR | \ 183 CSPR_V) 184 #define CONFIG_SYS_NOR1_CSPR_EXT (0xf) 185 #define CONFIG_SYS_NOR1_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \ 186 CSPR_PORT_SIZE_16 | \ 187 CSPR_MSEL_NOR | \ 188 CSPR_V) 189 #define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024) 190 /* NOR Flash Timing Params */ 191 #define CONFIG_SYS_NOR_CSOR CSOR_NAND_TRHZ_80 192 193 #define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \ 194 FTIM0_NOR_TEADC(0x5) | \ 195 FTIM0_NOR_TEAHC(0x5)) 196 #define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \ 197 FTIM1_NOR_TRAD_NOR(0x1A) |\ 198 FTIM1_NOR_TSEQRAD_NOR(0x13)) 199 #define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \ 200 FTIM2_NOR_TCH(0x4) | \ 201 FTIM2_NOR_TWPH(0x0E) | \ 202 FTIM2_NOR_TWP(0x1c)) 203 #define CONFIG_SYS_NOR_FTIM3 0x0 204 205 #define CONFIG_SYS_FLASH_QUIET_TEST 206 #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ 207 208 #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ 209 #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ 210 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 211 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 212 213 #define CONFIG_SYS_FLASH_EMPTY_INFO 214 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS \ 215 + 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS} 216 217 #define CONFIG_FSL_QIXIS /* use common QIXIS code */ 218 #define QIXIS_BASE 0xffdf0000 219 #define QIXIS_LBMAP_SWITCH 6 220 #define QIXIS_LBMAP_MASK 0x0f 221 #define QIXIS_LBMAP_SHIFT 0 222 #define QIXIS_LBMAP_DFLTBANK 0x00 223 #define QIXIS_LBMAP_ALTBANK 0x04 224 #define QIXIS_RST_CTL_RESET 0x83 225 #define QIXIS_RST_FORCE_MEM 0x1 226 #define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20 227 #define QIXIS_RCFG_CTL_RECONFIG_START 0x21 228 #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08 229 #define QIXIS_BASE_PHYS (0xf00000000ull | QIXIS_BASE) 230 231 #define CONFIG_SYS_CSPR3_EXT (0xf) 232 #define CONFIG_SYS_CSPR3 (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \ 233 | CSPR_PORT_SIZE_8 \ 234 | CSPR_MSEL_GPCM \ 235 | CSPR_V) 236 #define CONFIG_SYS_AMASK3 IFC_AMASK(4*1024) 237 #define CONFIG_SYS_CSOR3 0x0 238 /* QIXIS Timing parameters for IFC CS3 */ 239 #define CONFIG_SYS_CS3_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \ 240 FTIM0_GPCM_TEADC(0x0e) | \ 241 FTIM0_GPCM_TEAHC(0x0e)) 242 #define CONFIG_SYS_CS3_FTIM1 (FTIM1_GPCM_TACO(0xff) | \ 243 FTIM1_GPCM_TRAD(0x3f)) 244 #define CONFIG_SYS_CS3_FTIM2 (FTIM2_GPCM_TCS(0x0e) | \ 245 FTIM2_GPCM_TCH(0x8) | \ 246 FTIM2_GPCM_TWP(0x1f)) 247 #define CONFIG_SYS_CS3_FTIM3 0x0 248 249 /* NAND Flash on IFC */ 250 #define CONFIG_NAND_FSL_IFC 251 #define CONFIG_SYS_NAND_BASE 0xff800000 252 #define CONFIG_SYS_NAND_BASE_PHYS (0xf00000000ull | CONFIG_SYS_NAND_BASE) 253 254 #define CONFIG_SYS_NAND_CSPR_EXT (0xf) 255 #define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ 256 | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \ 257 | CSPR_MSEL_NAND /* MSEL = NAND */ \ 258 | CSPR_V) 259 #define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024) 260 261 #define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \ 262 | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \ 263 | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \ 264 | CSOR_NAND_RAL_3 /* RAL = 2Byes */ \ 265 | CSOR_NAND_PGS_2K /* Page Size = 2K */\ 266 | CSOR_NAND_SPRZ_64 /* Spare size = 64 */\ 267 | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/ 268 269 #define CONFIG_SYS_NAND_ONFI_DETECTION 270 271 /* ONFI NAND Flash mode0 Timing Params */ 272 #define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \ 273 FTIM0_NAND_TWP(0x18) | \ 274 FTIM0_NAND_TWCHT(0x07) | \ 275 FTIM0_NAND_TWH(0x0a)) 276 #define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \ 277 FTIM1_NAND_TWBE(0x39) | \ 278 FTIM1_NAND_TRR(0x0e) | \ 279 FTIM1_NAND_TRP(0x18)) 280 #define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \ 281 FTIM2_NAND_TREH(0x0a) | \ 282 FTIM2_NAND_TWHRE(0x1e)) 283 #define CONFIG_SYS_NAND_FTIM3 0x0 284 285 #define CONFIG_SYS_NAND_DDR_LAW 11 286 #define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } 287 #define CONFIG_SYS_MAX_NAND_DEVICE 1 288 #define CONFIG_MTD_NAND_VERIFY_WRITE 289 #define CONFIG_CMD_NAND 290 #define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) 291 292 #if defined(CONFIG_NAND) 293 #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT 294 #define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR 295 #define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK 296 #define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR 297 #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0 298 #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1 299 #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2 300 #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3 301 #define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NOR0_CSPR_EXT 302 #define CONFIG_SYS_CSPR2 CONFIG_SYS_NOR0_CSPR 303 #define CONFIG_SYS_AMASK2 CONFIG_SYS_NOR_AMASK 304 #define CONFIG_SYS_CSOR2 CONFIG_SYS_NOR_CSOR 305 #define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NOR_FTIM0 306 #define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NOR_FTIM1 307 #define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NOR_FTIM2 308 #define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NOR_FTIM3 309 #else 310 #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT 311 #define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR 312 #define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK 313 #define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR 314 #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0 315 #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1 316 #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2 317 #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3 318 #define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NAND_CSPR_EXT 319 #define CONFIG_SYS_CSPR2 CONFIG_SYS_NAND_CSPR 320 #define CONFIG_SYS_AMASK2 CONFIG_SYS_NAND_AMASK 321 #define CONFIG_SYS_CSOR2 CONFIG_SYS_NAND_CSOR 322 #define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NAND_FTIM0 323 #define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NAND_FTIM1 324 #define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NAND_FTIM2 325 #define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NAND_FTIM3 326 #endif 327 #define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR1_CSPR_EXT 328 #define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR1_CSPR 329 #define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK 330 #define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR 331 #define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0 332 #define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1 333 #define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2 334 #define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3 335 336 #if defined(CONFIG_RAMBOOT_PBL) 337 #define CONFIG_SYS_RAMBOOT 338 #endif 339 340 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE 341 #define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */ 342 #define CONFIG_MISC_INIT_R 343 #define CONFIG_HWCONFIG 344 345 /* define to use L1 as initial stack */ 346 #define CONFIG_L1_INIT_RAM 347 #define CONFIG_SYS_INIT_RAM_LOCK 348 #define CONFIG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */ 349 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf 350 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW 0xfe0ec000 351 /* The assembler doesn't like typecast */ 352 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \ 353 ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \ 354 CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW) 355 #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 356 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ 357 GENERATED_GBL_DATA_SIZE) 358 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 359 #define CONFIG_SYS_MONITOR_LEN (512 * 1024) 360 #define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024) 361 362 /* 363 * Serial Port 364 */ 365 #define CONFIG_CONS_INDEX 1 366 #define CONFIG_SYS_NS16550 367 #define CONFIG_SYS_NS16550_SERIAL 368 #define CONFIG_SYS_NS16550_REG_SIZE 1 369 #define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2) 370 #define CONFIG_SYS_BAUDRATE_TABLE \ 371 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} 372 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500) 373 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600) 374 #define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500) 375 #define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600) 376 377 /* Use the HUSH parser */ 378 #define CONFIG_SYS_HUSH_PARSER 379 #define CONFIG_SYS_PROMPT_HUSH_PS2 "> " 380 381 /* pass open firmware flat tree */ 382 #define CONFIG_OF_LIBFDT 383 #define CONFIG_OF_BOARD_SETUP 384 #define CONFIG_OF_STDOUT_VIA_ALIAS 385 386 /* new uImage format support */ 387 #define CONFIG_FIT 388 #define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ 389 390 /* 391 * I2C 392 */ 393 #define CONFIG_SYS_I2C 394 #define CONFIG_SYS_I2C_FSL 395 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 396 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F 397 #define CONFIG_SYS_FSL_I2C3_SLAVE 0x7F 398 #define CONFIG_SYS_FSL_I2C4_SLAVE 0x7F 399 #define CONFIG_SYS_FSL_I2C_OFFSET 0x118000 400 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100 401 #define CONFIG_SYS_FSL_I2C3_OFFSET 0x119000 402 #define CONFIG_SYS_FSL_I2C4_OFFSET 0x119100 403 #define CONFIG_SYS_FSL_I2C_SPEED 100000 404 #define CONFIG_SYS_FSL_I2C2_SPEED 100000 405 #define CONFIG_SYS_FSL_I2C3_SPEED 100000 406 #define CONFIG_SYS_FSL_I2C4_SPEED 100000 407 #define I2C_MUX_PCA_ADDR_PRI 0x77 /* I2C bus multiplexer,primary */ 408 #define I2C_MUX_PCA_ADDR_SEC1 0x75 /* I2C bus multiplexer,secondary 1 */ 409 #define I2C_MUX_PCA_ADDR_SEC2 0x76 /* I2C bus multiplexer,secondary 2 */ 410 #define I2C_MUX_CH_DEFAULT 0x8 411 412 413 /* 414 * RapidIO 415 */ 416 #define CONFIG_SYS_SRIO1_MEM_VIRT 0xa0000000 417 #define CONFIG_SYS_SRIO1_MEM_PHYS 0xc20000000ull 418 #define CONFIG_SYS_SRIO1_MEM_SIZE 0x10000000 /* 256M */ 419 #define CONFIG_SYS_SRIO2_MEM_VIRT 0xb0000000 420 #define CONFIG_SYS_SRIO2_MEM_PHYS 0xc30000000ull 421 #define CONFIG_SYS_SRIO2_MEM_SIZE 0x10000000 /* 256M */ 422 /* 423 * for slave u-boot IMAGE instored in master memory space, 424 * PHYS must be aligned based on the SIZE 425 */ 426 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef080000ull 427 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff80000ull 428 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x80000 /* 512K */ 429 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff80000ull 430 /* 431 * for slave UCODE and ENV instored in master memory space, 432 * PHYS must be aligned based on the SIZE 433 */ 434 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef040000ull 435 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull 436 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */ 437 438 /* slave core release by master*/ 439 #define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4 440 #define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */ 441 442 /* 443 * SRIO_PCIE_BOOT - SLAVE 444 */ 445 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE 446 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000 447 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \ 448 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR) 449 #endif 450 451 /* 452 * eSPI - Enhanced SPI 453 */ 454 #ifdef CONFIG_SPI_FLASH 455 #define CONFIG_FSL_ESPI 456 #define CONFIG_SPI_FLASH_SST 457 #define CONFIG_SPI_FLASH_STMICRO 458 #if defined(CONFIG_T2080QDS) 459 #define CONFIG_SPI_FLASH_SPANSION 460 #elif defined(CONFIG_T2081QDS) 461 #define CONFIG_SPI_FLASH_EON 462 #endif 463 464 #define CONFIG_CMD_SF 465 #define CONFIG_SF_DEFAULT_SPEED 10000000 466 #define CONFIG_SF_DEFAULT_MODE 0 467 #endif 468 469 /* 470 * General PCI 471 * Memory space is mapped 1-1, but I/O space must start from 0. 472 */ 473 #define CONFIG_PCI /* Enable PCI/PCIE */ 474 #define CONFIG_PCIE1 /* PCIE controler 1 */ 475 #define CONFIG_PCIE2 /* PCIE controler 2 */ 476 #define CONFIG_PCIE3 /* PCIE controler 3 */ 477 #define CONFIG_PCIE4 /* PCIE controler 4 */ 478 #define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ 479 #define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ 480 /* controller 1, direct to uli, tgtid 3, Base address 20000 */ 481 #define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 482 #define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 483 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull 484 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ 485 #define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000 486 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 487 #define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull 488 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ 489 490 /* controller 2, Slot 2, tgtid 2, Base address 201000 */ 491 #define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 492 #define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000 493 #define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull 494 #define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */ 495 #define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000 496 #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 497 #define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull 498 #define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ 499 500 /* controller 3, Slot 1, tgtid 1, Base address 202000 */ 501 #define CONFIG_SYS_PCIE3_MEM_VIRT 0xb0000000 502 #define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000 503 #define CONFIG_SYS_PCIE3_MEM_PHYS 0xc30000000ull 504 #define CONFIG_SYS_PCIE3_MEM_SIZE 0x10000000 /* 256M */ 505 #define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000 506 #define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 507 #define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull 508 #define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */ 509 510 /* controller 4, Base address 203000 */ 511 #define CONFIG_SYS_PCIE4_MEM_VIRT 0xc0000000 512 #define CONFIG_SYS_PCIE4_MEM_BUS 0xe0000000 513 #define CONFIG_SYS_PCIE4_MEM_PHYS 0xc40000000ull 514 #define CONFIG_SYS_PCIE4_MEM_SIZE 0x10000000 /* 256M */ 515 #define CONFIG_SYS_PCIE4_IO_BUS 0x00000000 516 #define CONFIG_SYS_PCIE4_IO_PHYS 0xff8030000ull 517 #define CONFIG_SYS_PCIE4_IO_SIZE 0x00010000 /* 64k */ 518 519 #ifdef CONFIG_PCI 520 #define CONFIG_PCI_INDIRECT_BRIDGE 521 #define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata */ 522 #define CONFIG_NET_MULTI 523 #define CONFIG_E1000 524 #define CONFIG_PCI_PNP /* do pci plug-and-play */ 525 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 526 #define CONFIG_DOS_PARTITION 527 #endif 528 529 /* Qman/Bman */ 530 #ifndef CONFIG_NOBQFMAN 531 #define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */ 532 #define CONFIG_SYS_BMAN_NUM_PORTALS 18 533 #define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000 534 #define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull 535 #define CONFIG_SYS_BMAN_MEM_SIZE 0x02000000 536 #define CONFIG_SYS_QMAN_NUM_PORTALS 18 537 #define CONFIG_SYS_QMAN_MEM_BASE 0xf6000000 538 #define CONFIG_SYS_QMAN_MEM_PHYS 0xff6000000ull 539 #define CONFIG_SYS_QMAN_MEM_SIZE 0x02000000 540 541 #define CONFIG_SYS_DPAA_FMAN 542 #define CONFIG_SYS_DPAA_PME 543 #define CONFIG_SYS_PMAN 544 #define CONFIG_SYS_DPAA_DCE 545 #define CONFIG_SYS_DPAA_RMAN /* RMan */ 546 #define CONFIG_SYS_INTERLAKEN 547 548 /* Default address of microcode for the Linux Fman driver */ 549 #if defined(CONFIG_SPIFLASH) 550 /* 551 * env is stored at 0x100000, sector size is 0x10000, ucode is stored after 552 * env, so we got 0x110000. 553 */ 554 #define CONFIG_SYS_QE_FW_IN_SPIFLASH 555 #define CONFIG_SYS_QE_FMAN_FW_ADDR 0x110000 556 #elif defined(CONFIG_SDCARD) 557 /* 558 * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is 559 * about 825KB (1650 blocks), Env is stored after the image, and the env size is 560 * 0x2000 (16 blocks), 8 + 1650 + 16 = 1674, enlarge it to 1680. 561 */ 562 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC 563 #define CONFIG_SYS_QE_FMAN_FW_ADDR (512 * 1680) 564 #elif defined(CONFIG_NAND) 565 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND 566 #define CONFIG_SYS_QE_FMAN_FW_ADDR (8 * CONFIG_SYS_NAND_BLOCK_SIZE) 567 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) 568 /* 569 * Slave has no ucode locally, it can fetch this from remote. When implementing 570 * in two corenet boards, slave's ucode could be stored in master's memory 571 * space, the address can be mapped from slave TLB->slave LAW-> 572 * slave SRIO or PCIE outbound window->master inbound window-> 573 * master LAW->the ucode address in master's memory space. 574 */ 575 #define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE 576 #define CONFIG_SYS_QE_FMAN_FW_ADDR 0xFFE00000 577 #else 578 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR 579 #define CONFIG_SYS_QE_FMAN_FW_ADDR 0xEFF00000 580 #endif 581 #define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 582 #define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) 583 #endif /* CONFIG_NOBQFMAN */ 584 585 #ifdef CONFIG_SYS_DPAA_FMAN 586 #define CONFIG_FMAN_ENET 587 #define CONFIG_PHYLIB_10G 588 #define CONFIG_PHY_VITESSE 589 #define CONFIG_PHY_REALTEK 590 #define CONFIG_PHY_TERANETICS 591 #define RGMII_PHY1_ADDR 0x1 592 #define RGMII_PHY2_ADDR 0x2 593 #define FM1_10GEC1_PHY_ADDR 0x3 594 #define SGMII_CARD_PORT1_PHY_ADDR 0x1C 595 #define SGMII_CARD_PORT2_PHY_ADDR 0x1D 596 #define SGMII_CARD_PORT3_PHY_ADDR 0x1E 597 #define SGMII_CARD_PORT4_PHY_ADDR 0x1F 598 #endif 599 600 #ifdef CONFIG_FMAN_ENET 601 #define CONFIG_MII /* MII PHY management */ 602 #define CONFIG_ETHPRIME "FM1@DTSEC3" 603 #define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ 604 #endif 605 606 /* 607 * SATA 608 */ 609 #ifdef CONFIG_FSL_SATA_V2 610 #define CONFIG_LIBATA 611 #define CONFIG_FSL_SATA 612 #define CONFIG_SYS_SATA_MAX_DEVICE 2 613 #define CONFIG_SATA1 614 #define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR 615 #define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA 616 #define CONFIG_SATA2 617 #define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR 618 #define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA 619 #define CONFIG_LBA48 620 #define CONFIG_CMD_SATA 621 #define CONFIG_DOS_PARTITION 622 #define CONFIG_CMD_EXT2 623 #endif 624 625 /* 626 * USB 627 */ 628 #ifdef CONFIG_USB_EHCI 629 #define CONFIG_CMD_USB 630 #define CONFIG_USB_STORAGE 631 #define CONFIG_USB_EHCI_FSL 632 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET 633 #define CONFIG_CMD_EXT2 634 #define CONFIG_HAS_FSL_DR_USB 635 #endif 636 637 /* 638 * SDHC 639 */ 640 #ifdef CONFIG_MMC 641 #define CONFIG_CMD_MMC 642 #define CONFIG_FSL_ESDHC 643 #define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR 644 #define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT 645 #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33 646 #define CONFIG_GENERIC_MMC 647 #define CONFIG_CMD_EXT2 648 #define CONFIG_CMD_FAT 649 #define CONFIG_DOS_PARTITION 650 #endif 651 652 /* 653 * Environment 654 */ 655 #define CONFIG_LOADS_ECHO /* echo on for serial download */ 656 #define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ 657 658 /* 659 * Command line configuration. 660 */ 661 #include <config_cmd_default.h> 662 663 #define CONFIG_CMD_DHCP 664 #define CONFIG_CMD_ELF 665 #define CONFIG_CMD_ERRATA 666 #define CONFIG_CMD_GREPENV 667 #define CONFIG_CMD_IRQ 668 #define CONFIG_CMD_I2C 669 #define CONFIG_CMD_MII 670 #define CONFIG_CMD_PING 671 #define CONFIG_CMD_SETEXPR 672 #define CONFIG_CMD_REGINFO 673 #define CONFIG_CMD_BDI 674 675 #ifdef CONFIG_PCI 676 #define CONFIG_CMD_PCI 677 #define CONFIG_CMD_NET 678 #endif 679 680 /* 681 * Miscellaneous configurable options 682 */ 683 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 684 #define CONFIG_CMDLINE_EDITING /* Command-line editing */ 685 #define CONFIG_AUTO_COMPLETE /* add autocompletion support */ 686 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 687 #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ 688 #ifdef CONFIG_CMD_KGDB 689 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 690 #else 691 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 692 #endif 693 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) 694 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 695 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */ 696 697 /* 698 * For booting Linux, the board info and command line data 699 * have to be in the first 64 MB of memory, since this is 700 * the maximum mapped by the Linux kernel during initialization. 701 */ 702 #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial map for Linux*/ 703 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 704 705 #ifdef CONFIG_CMD_KGDB 706 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ 707 #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ 708 #endif 709 710 /* 711 * Environment Configuration 712 */ 713 #define CONFIG_ROOTPATH "/opt/nfsroot" 714 #define CONFIG_BOOTFILE "uImage" 715 #define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server */ 716 717 /* default location for tftp and bootm */ 718 #define CONFIG_LOADADDR 1000000 719 #define CONFIG_BAUDRATE 115200 720 #define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ 721 #define __USB_PHY_TYPE utmi 722 723 #define CONFIG_EXTRA_ENV_SETTINGS \ 724 "hwconfig=fsl_ddr:" \ 725 "ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) "," \ 726 "bank_intlv=auto;" \ 727 "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\ 728 "netdev=eth0\0" \ 729 "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ 730 "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \ 731 "tftpflash=tftpboot $loadaddr $uboot && " \ 732 "protect off $ubootaddr +$filesize && " \ 733 "erase $ubootaddr +$filesize && " \ 734 "cp.b $loadaddr $ubootaddr $filesize && " \ 735 "protect on $ubootaddr +$filesize && " \ 736 "cmp.b $loadaddr $ubootaddr $filesize\0" \ 737 "consoledev=ttyS0\0" \ 738 "ramdiskaddr=2000000\0" \ 739 "ramdiskfile=t2080qds/ramdisk.uboot\0" \ 740 "fdtaddr=c00000\0" \ 741 "fdtfile=t2080qds/t2080qds.dtb\0" \ 742 "bdev=sda3\0" \ 743 "c=ffe\0" 744 745 /* 746 * For emulation this causes u-boot to jump to the start of the 747 * proof point app code automatically 748 */ 749 #define CONFIG_PROOF_POINTS \ 750 "setenv bootargs root=/dev/$bdev rw " \ 751 "console=$consoledev,$baudrate $othbootargs;" \ 752 "cpu 1 release 0x29000000 - - -;" \ 753 "cpu 2 release 0x29000000 - - -;" \ 754 "cpu 3 release 0x29000000 - - -;" \ 755 "cpu 4 release 0x29000000 - - -;" \ 756 "cpu 5 release 0x29000000 - - -;" \ 757 "cpu 6 release 0x29000000 - - -;" \ 758 "cpu 7 release 0x29000000 - - -;" \ 759 "go 0x29000000" 760 761 #define CONFIG_HVBOOT \ 762 "setenv bootargs config-addr=0x60000000; " \ 763 "bootm 0x01000000 - 0x00f00000" 764 765 #define CONFIG_ALU \ 766 "setenv bootargs root=/dev/$bdev rw " \ 767 "console=$consoledev,$baudrate $othbootargs;" \ 768 "cpu 1 release 0x01000000 - - -;" \ 769 "cpu 2 release 0x01000000 - - -;" \ 770 "cpu 3 release 0x01000000 - - -;" \ 771 "cpu 4 release 0x01000000 - - -;" \ 772 "cpu 5 release 0x01000000 - - -;" \ 773 "cpu 6 release 0x01000000 - - -;" \ 774 "cpu 7 release 0x01000000 - - -;" \ 775 "go 0x01000000" 776 777 #define CONFIG_LINUX \ 778 "setenv bootargs root=/dev/ram rw " \ 779 "console=$consoledev,$baudrate $othbootargs;" \ 780 "setenv ramdiskaddr 0x02000000;" \ 781 "setenv fdtaddr 0x00c00000;" \ 782 "setenv loadaddr 0x1000000;" \ 783 "bootm $loadaddr $ramdiskaddr $fdtaddr" 784 785 #define CONFIG_HDBOOT \ 786 "setenv bootargs root=/dev/$bdev rw " \ 787 "console=$consoledev,$baudrate $othbootargs;" \ 788 "tftp $loadaddr $bootfile;" \ 789 "tftp $fdtaddr $fdtfile;" \ 790 "bootm $loadaddr - $fdtaddr" 791 792 #define CONFIG_NFSBOOTCOMMAND \ 793 "setenv bootargs root=/dev/nfs rw " \ 794 "nfsroot=$serverip:$rootpath " \ 795 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 796 "console=$consoledev,$baudrate $othbootargs;" \ 797 "tftp $loadaddr $bootfile;" \ 798 "tftp $fdtaddr $fdtfile;" \ 799 "bootm $loadaddr - $fdtaddr" 800 801 #define CONFIG_RAMBOOTCOMMAND \ 802 "setenv bootargs root=/dev/ram rw " \ 803 "console=$consoledev,$baudrate $othbootargs;" \ 804 "tftp $ramdiskaddr $ramdiskfile;" \ 805 "tftp $loadaddr $bootfile;" \ 806 "tftp $fdtaddr $fdtfile;" \ 807 "bootm $loadaddr $ramdiskaddr $fdtaddr" 808 809 #define CONFIG_BOOTCOMMAND CONFIG_LINUX 810 811 #ifdef CONFIG_SECURE_BOOT 812 #include <asm/fsl_secure_boot.h> 813 #undef CONFIG_CMD_USB 814 #endif 815 816 #endif /* __T208xQDS_H */ 817