1 /* 2 * Copyright 2011-2013 Freescale Semiconductor, Inc. 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 /* 8 * T2080/T2081 QDS board configuration file 9 */ 10 11 #ifndef __T208xQDS_H 12 #define __T208xQDS_H 13 14 #define CONFIG_ICS307_REFCLK_HZ 25000000 /* ICS307 ref clk freq */ 15 #define CONFIG_MMC 16 #define CONFIG_SPI_FLASH 17 #define CONFIG_USB_EHCI 18 #if defined(CONFIG_PPC_T2080) 19 #define CONFIG_T2080QDS 20 #define CONFIG_FSL_SATA_V2 21 #define CONFIG_SYS_SRIO /* Enable Serial RapidIO Support */ 22 #define CONFIG_SRIO1 /* SRIO port 1 */ 23 #define CONFIG_SRIO2 /* SRIO port 2 */ 24 #elif defined(CONFIG_PPC_T2081) 25 #define CONFIG_T2081QDS 26 #endif 27 28 /* High Level Configuration Options */ 29 #define CONFIG_PHYS_64BIT 30 #define CONFIG_BOOKE 31 #define CONFIG_E500 /* BOOKE e500 family */ 32 #define CONFIG_E500MC /* BOOKE e500mc family */ 33 #define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */ 34 #define CONFIG_MP /* support multiple processors */ 35 #define CONFIG_ENABLE_36BIT_PHYS 36 37 #ifdef CONFIG_PHYS_64BIT 38 #define CONFIG_ADDR_MAP 1 39 #define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */ 40 #endif 41 42 #define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */ 43 #define CONFIG_SYS_NUM_CPC CONFIG_NUM_DDR_CONTROLLERS 44 #define CONFIG_FSL_IFC /* Enable IFC Support */ 45 #define CONFIG_FSL_LAW /* Use common FSL init code */ 46 #define CONFIG_ENV_OVERWRITE 47 48 #ifdef CONFIG_RAMBOOT_PBL 49 #define CONFIG_SYS_FSL_PBL_PBI board/freescale/t208xqds/t208x_pbi.cfg 50 #if defined(CONFIG_PPC_T2080) 51 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xqds/t2080_rcw.cfg 52 #elif defined(CONFIG_PPC_T2081) 53 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xqds/t2081_rcw.cfg 54 #endif 55 56 #define CONFIG_SPL 57 #define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT 58 #define CONFIG_SPL_ENV_SUPPORT 59 #define CONFIG_SPL_SERIAL_SUPPORT 60 #define CONFIG_SPL_FLUSH_IMAGE 61 #define CONFIG_SPL_TARGET "u-boot-with-spl.bin" 62 #define CONFIG_SPL_LIBGENERIC_SUPPORT 63 #define CONFIG_SPL_LIBCOMMON_SUPPORT 64 #define CONFIG_SPL_I2C_SUPPORT 65 #define CONFIG_SPL_DRIVERS_MISC_SUPPORT 66 #define CONFIG_FSL_LAW /* Use common FSL init code */ 67 #define CONFIG_SYS_TEXT_BASE 0x00201000 68 #define CONFIG_SPL_TEXT_BASE 0xFFFD8000 69 #define CONFIG_SPL_PAD_TO 0x40000 70 #define CONFIG_SPL_MAX_SIZE 0x28000 71 #define RESET_VECTOR_OFFSET 0x27FFC 72 #define BOOT_PAGE_OFFSET 0x27000 73 #ifdef CONFIG_SPL_BUILD 74 #define CONFIG_SPL_SKIP_RELOCATE 75 #define CONFIG_SPL_COMMON_INIT_DDR 76 #define CONFIG_SYS_CCSR_DO_NOT_RELOCATE 77 #define CONFIG_SYS_NO_FLASH 78 #endif 79 80 #ifdef CONFIG_NAND 81 #define CONFIG_SPL_NAND_SUPPORT 82 #define CONFIG_SYS_NAND_U_BOOT_SIZE (768 << 10) 83 #define CONFIG_SYS_NAND_U_BOOT_DST 0x00200000 84 #define CONFIG_SYS_NAND_U_BOOT_START 0x00200000 85 #define CONFIG_SYS_NAND_U_BOOT_OFFS (256 << 10) 86 #define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot-nand.lds" 87 #define CONFIG_SPL_NAND_BOOT 88 #endif 89 90 #ifdef CONFIG_SPIFLASH 91 #define CONFIG_RESET_VECTOR_ADDRESS 0x200FFC 92 #define CONFIG_SPL_SPI_SUPPORT 93 #define CONFIG_SPL_SPI_FLASH_SUPPORT 94 #define CONFIG_SPL_SPI_FLASH_MINIMAL 95 #define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE (768 << 10) 96 #define CONFIG_SYS_SPI_FLASH_U_BOOT_DST (0x00200000) 97 #define CONFIG_SYS_SPI_FLASH_U_BOOT_START (0x00200000) 98 #define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS (256 << 10) 99 #define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot.lds" 100 #ifndef CONFIG_SPL_BUILD 101 #define CONFIG_SYS_MPC85XX_NO_RESETVEC 102 #endif 103 #define CONFIG_SPL_SPI_BOOT 104 #endif 105 106 #ifdef CONFIG_SDCARD 107 #define CONFIG_RESET_VECTOR_ADDRESS 0x200FFC 108 #define CONFIG_SPL_MMC_SUPPORT 109 #define CONFIG_SPL_MMC_MINIMAL 110 #define CONFIG_SYS_MMC_U_BOOT_SIZE (768 << 10) 111 #define CONFIG_SYS_MMC_U_BOOT_DST (0x00200000) 112 #define CONFIG_SYS_MMC_U_BOOT_START (0x00200000) 113 #define CONFIG_SYS_MMC_U_BOOT_OFFS (260 << 10) 114 #define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot.lds" 115 #ifndef CONFIG_SPL_BUILD 116 #define CONFIG_SYS_MPC85XX_NO_RESETVEC 117 #endif 118 #define CONFIG_SPL_MMC_BOOT 119 #endif 120 121 #endif /* CONFIG_RAMBOOT_PBL */ 122 123 #define CONFIG_SRIO_PCIE_BOOT_MASTER 124 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE 125 /* Set 1M boot space */ 126 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000) 127 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \ 128 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR) 129 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc 130 #define CONFIG_SYS_NO_FLASH 131 #endif 132 133 #ifndef CONFIG_SYS_TEXT_BASE 134 #define CONFIG_SYS_TEXT_BASE 0xeff40000 135 #endif 136 137 #ifndef CONFIG_RESET_VECTOR_ADDRESS 138 #define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc 139 #endif 140 141 /* 142 * These can be toggled for performance analysis, otherwise use default. 143 */ 144 #define CONFIG_SYS_CACHE_STASHING 145 #define CONFIG_BTB /* toggle branch predition */ 146 #define CONFIG_DDR_ECC 147 #ifdef CONFIG_DDR_ECC 148 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER 149 #define CONFIG_MEM_INIT_VALUE 0xdeadbeef 150 #endif 151 152 #ifndef CONFIG_SYS_NO_FLASH 153 #define CONFIG_FLASH_CFI_DRIVER 154 #define CONFIG_SYS_FLASH_CFI 155 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 156 #endif 157 158 #if defined(CONFIG_SPIFLASH) 159 #define CONFIG_SYS_EXTRA_ENV_RELOC 160 #define CONFIG_ENV_IS_IN_SPI_FLASH 161 #define CONFIG_ENV_SPI_BUS 0 162 #define CONFIG_ENV_SPI_CS 0 163 #define CONFIG_ENV_SPI_MAX_HZ 10000000 164 #define CONFIG_ENV_SPI_MODE 0 165 #define CONFIG_ENV_SIZE 0x2000 /* 8KB */ 166 #define CONFIG_ENV_OFFSET 0x100000 /* 1MB */ 167 #define CONFIG_ENV_SECT_SIZE 0x10000 168 #elif defined(CONFIG_SDCARD) 169 #define CONFIG_SYS_EXTRA_ENV_RELOC 170 #define CONFIG_ENV_IS_IN_MMC 171 #define CONFIG_SYS_MMC_ENV_DEV 0 172 #define CONFIG_ENV_SIZE 0x2000 173 #define CONFIG_ENV_OFFSET (512 * 0x800) 174 #elif defined(CONFIG_NAND) 175 #define CONFIG_SYS_EXTRA_ENV_RELOC 176 #define CONFIG_ENV_IS_IN_NAND 177 #define CONFIG_ENV_SIZE 0x2000 178 #define CONFIG_ENV_OFFSET (10 * CONFIG_SYS_NAND_BLOCK_SIZE) 179 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) 180 #define CONFIG_ENV_IS_IN_REMOTE 181 #define CONFIG_ENV_ADDR 0xffe20000 182 #define CONFIG_ENV_SIZE 0x2000 183 #elif defined(CONFIG_ENV_IS_NOWHERE) 184 #define CONFIG_ENV_SIZE 0x2000 185 #else 186 #define CONFIG_ENV_IS_IN_FLASH 187 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) 188 #define CONFIG_ENV_SIZE 0x2000 189 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ 190 #endif 191 192 #ifndef __ASSEMBLY__ 193 unsigned long get_board_sys_clk(void); 194 unsigned long get_board_ddr_clk(void); 195 #endif 196 197 #define CONFIG_SYS_CLK_FREQ get_board_sys_clk() 198 #define CONFIG_DDR_CLK_FREQ get_board_ddr_clk() 199 200 /* 201 * Config the L3 Cache as L3 SRAM 202 */ 203 #define CONFIG_SYS_INIT_L3_ADDR 0xFFFC0000 204 #define CONFIG_SYS_L3_SIZE (512 << 10) 205 #define CONFIG_SPL_GD_ADDR (CONFIG_SYS_INIT_L3_ADDR + 32 * 1024) 206 #ifdef CONFIG_RAMBOOT_PBL 207 #define CONFIG_ENV_ADDR (CONFIG_SPL_GD_ADDR + 4 * 1024) 208 #endif 209 #define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SPL_GD_ADDR + 12 * 1024) 210 #define CONFIG_SPL_RELOC_MALLOC_SIZE (50 << 10) 211 #define CONFIG_SPL_RELOC_STACK (CONFIG_SPL_GD_ADDR + 64 * 1024) 212 #define CONFIG_SPL_RELOC_STACK_SIZE (22 << 10) 213 214 #define CONFIG_SYS_DCSRBAR 0xf0000000 215 #define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull 216 217 /* EEPROM */ 218 #define CONFIG_ID_EEPROM 219 #define CONFIG_SYS_I2C_EEPROM_NXID 220 #define CONFIG_SYS_EEPROM_BUS_NUM 0 221 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 222 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 223 224 /* 225 * DDR Setup 226 */ 227 #define CONFIG_VERY_BIG_RAM 228 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 229 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 230 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 231 #define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR) 232 #define CONFIG_DDR_SPD 233 #define CONFIG_SYS_FSL_DDR3 234 #undef CONFIG_FSL_DDR_INTERACTIVE 235 #define CONFIG_SYS_SPD_BUS_NUM 0 236 #define CONFIG_SYS_SDRAM_SIZE 2048 /* for fixed parameter use */ 237 #define SPD_EEPROM_ADDRESS1 0x51 238 #define SPD_EEPROM_ADDRESS2 0x52 239 #define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1 240 #define CTRL_INTLV_PREFERED cacheline 241 242 /* 243 * IFC Definitions 244 */ 245 #define CONFIG_SYS_FLASH_BASE 0xe0000000 246 #define CONFIG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CONFIG_SYS_FLASH_BASE) 247 #define CONFIG_SYS_NOR0_CSPR_EXT (0xf) 248 #define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS \ 249 + 0x8000000) | \ 250 CSPR_PORT_SIZE_16 | \ 251 CSPR_MSEL_NOR | \ 252 CSPR_V) 253 #define CONFIG_SYS_NOR1_CSPR_EXT (0xf) 254 #define CONFIG_SYS_NOR1_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \ 255 CSPR_PORT_SIZE_16 | \ 256 CSPR_MSEL_NOR | \ 257 CSPR_V) 258 #define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024) 259 /* NOR Flash Timing Params */ 260 #define CONFIG_SYS_NOR_CSOR CSOR_NAND_TRHZ_80 261 262 #define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \ 263 FTIM0_NOR_TEADC(0x5) | \ 264 FTIM0_NOR_TEAHC(0x5)) 265 #define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \ 266 FTIM1_NOR_TRAD_NOR(0x1A) |\ 267 FTIM1_NOR_TSEQRAD_NOR(0x13)) 268 #define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \ 269 FTIM2_NOR_TCH(0x4) | \ 270 FTIM2_NOR_TWPH(0x0E) | \ 271 FTIM2_NOR_TWP(0x1c)) 272 #define CONFIG_SYS_NOR_FTIM3 0x0 273 274 #define CONFIG_SYS_FLASH_QUIET_TEST 275 #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ 276 277 #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ 278 #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ 279 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 280 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 281 282 #define CONFIG_SYS_FLASH_EMPTY_INFO 283 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS \ 284 + 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS} 285 286 #define CONFIG_FSL_QIXIS /* use common QIXIS code */ 287 #define QIXIS_BASE 0xffdf0000 288 #define QIXIS_LBMAP_SWITCH 6 289 #define QIXIS_LBMAP_MASK 0x0f 290 #define QIXIS_LBMAP_SHIFT 0 291 #define QIXIS_LBMAP_DFLTBANK 0x00 292 #define QIXIS_LBMAP_ALTBANK 0x04 293 #define QIXIS_RST_CTL_RESET 0x83 294 #define QIXIS_RST_FORCE_MEM 0x1 295 #define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20 296 #define QIXIS_RCFG_CTL_RECONFIG_START 0x21 297 #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08 298 #define QIXIS_BASE_PHYS (0xf00000000ull | QIXIS_BASE) 299 300 #define CONFIG_SYS_CSPR3_EXT (0xf) 301 #define CONFIG_SYS_CSPR3 (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \ 302 | CSPR_PORT_SIZE_8 \ 303 | CSPR_MSEL_GPCM \ 304 | CSPR_V) 305 #define CONFIG_SYS_AMASK3 IFC_AMASK(4*1024) 306 #define CONFIG_SYS_CSOR3 0x0 307 /* QIXIS Timing parameters for IFC CS3 */ 308 #define CONFIG_SYS_CS3_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \ 309 FTIM0_GPCM_TEADC(0x0e) | \ 310 FTIM0_GPCM_TEAHC(0x0e)) 311 #define CONFIG_SYS_CS3_FTIM1 (FTIM1_GPCM_TACO(0xff) | \ 312 FTIM1_GPCM_TRAD(0x3f)) 313 #define CONFIG_SYS_CS3_FTIM2 (FTIM2_GPCM_TCS(0x0e) | \ 314 FTIM2_GPCM_TCH(0x8) | \ 315 FTIM2_GPCM_TWP(0x1f)) 316 #define CONFIG_SYS_CS3_FTIM3 0x0 317 318 /* NAND Flash on IFC */ 319 #define CONFIG_NAND_FSL_IFC 320 #define CONFIG_SYS_NAND_BASE 0xff800000 321 #define CONFIG_SYS_NAND_BASE_PHYS (0xf00000000ull | CONFIG_SYS_NAND_BASE) 322 323 #define CONFIG_SYS_NAND_CSPR_EXT (0xf) 324 #define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ 325 | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \ 326 | CSPR_MSEL_NAND /* MSEL = NAND */ \ 327 | CSPR_V) 328 #define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024) 329 330 #define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \ 331 | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \ 332 | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \ 333 | CSOR_NAND_RAL_3 /* RAL = 2Byes */ \ 334 | CSOR_NAND_PGS_2K /* Page Size = 2K */\ 335 | CSOR_NAND_SPRZ_64 /* Spare size = 64 */\ 336 | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/ 337 338 #define CONFIG_SYS_NAND_ONFI_DETECTION 339 340 /* ONFI NAND Flash mode0 Timing Params */ 341 #define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \ 342 FTIM0_NAND_TWP(0x18) | \ 343 FTIM0_NAND_TWCHT(0x07) | \ 344 FTIM0_NAND_TWH(0x0a)) 345 #define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \ 346 FTIM1_NAND_TWBE(0x39) | \ 347 FTIM1_NAND_TRR(0x0e) | \ 348 FTIM1_NAND_TRP(0x18)) 349 #define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \ 350 FTIM2_NAND_TREH(0x0a) | \ 351 FTIM2_NAND_TWHRE(0x1e)) 352 #define CONFIG_SYS_NAND_FTIM3 0x0 353 354 #define CONFIG_SYS_NAND_DDR_LAW 11 355 #define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } 356 #define CONFIG_SYS_MAX_NAND_DEVICE 1 357 #define CONFIG_MTD_NAND_VERIFY_WRITE 358 #define CONFIG_CMD_NAND 359 #define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) 360 361 #if defined(CONFIG_NAND) 362 #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT 363 #define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR 364 #define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK 365 #define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR 366 #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0 367 #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1 368 #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2 369 #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3 370 #define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR0_CSPR_EXT 371 #define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR0_CSPR 372 #define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK 373 #define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR 374 #define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0 375 #define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1 376 #define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2 377 #define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3 378 #define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NOR1_CSPR_EXT 379 #define CONFIG_SYS_CSPR2 CONFIG_SYS_NOR1_CSPR 380 #define CONFIG_SYS_AMASK2 CONFIG_SYS_NOR_AMASK 381 #define CONFIG_SYS_CSOR2 CONFIG_SYS_NOR_CSOR 382 #define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NOR_FTIM0 383 #define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NOR_FTIM1 384 #define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NOR_FTIM2 385 #define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NOR_FTIM3 386 #else 387 #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT 388 #define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR 389 #define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK 390 #define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR 391 #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0 392 #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1 393 #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2 394 #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3 395 #define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR1_CSPR_EXT 396 #define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR1_CSPR 397 #define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK 398 #define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR 399 #define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0 400 #define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1 401 #define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2 402 #define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3 403 #define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NAND_CSPR_EXT 404 #define CONFIG_SYS_CSPR2 CONFIG_SYS_NAND_CSPR 405 #define CONFIG_SYS_AMASK2 CONFIG_SYS_NAND_AMASK 406 #define CONFIG_SYS_CSOR2 CONFIG_SYS_NAND_CSOR 407 #define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NAND_FTIM0 408 #define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NAND_FTIM1 409 #define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NAND_FTIM2 410 #define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NAND_FTIM3 411 #endif 412 413 #if defined(CONFIG_RAMBOOT_PBL) 414 #define CONFIG_SYS_RAMBOOT 415 #endif 416 417 #ifdef CONFIG_SPL_BUILD 418 #define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE 419 #else 420 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 421 #endif 422 423 #define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */ 424 #define CONFIG_MISC_INIT_R 425 #define CONFIG_HWCONFIG 426 427 /* define to use L1 as initial stack */ 428 #define CONFIG_L1_INIT_RAM 429 #define CONFIG_SYS_INIT_RAM_LOCK 430 #define CONFIG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */ 431 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf 432 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW 0xfe0ec000 433 /* The assembler doesn't like typecast */ 434 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \ 435 ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \ 436 CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW) 437 #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 438 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ 439 GENERATED_GBL_DATA_SIZE) 440 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 441 #define CONFIG_SYS_MONITOR_LEN (768 * 1024) 442 #define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024) 443 444 /* 445 * Serial Port 446 */ 447 #define CONFIG_CONS_INDEX 1 448 #define CONFIG_SYS_NS16550 449 #define CONFIG_SYS_NS16550_SERIAL 450 #define CONFIG_SYS_NS16550_REG_SIZE 1 451 #define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2) 452 #define CONFIG_SYS_BAUDRATE_TABLE \ 453 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} 454 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500) 455 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600) 456 #define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500) 457 #define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600) 458 459 /* Use the HUSH parser */ 460 #define CONFIG_SYS_HUSH_PARSER 461 #define CONFIG_SYS_PROMPT_HUSH_PS2 "> " 462 463 /* pass open firmware flat tree */ 464 #define CONFIG_OF_LIBFDT 465 #define CONFIG_OF_BOARD_SETUP 466 #define CONFIG_OF_STDOUT_VIA_ALIAS 467 468 /* new uImage format support */ 469 #define CONFIG_FIT 470 #define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ 471 472 /* 473 * I2C 474 */ 475 #define CONFIG_SYS_I2C 476 #define CONFIG_SYS_I2C_FSL 477 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 478 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F 479 #define CONFIG_SYS_FSL_I2C3_SLAVE 0x7F 480 #define CONFIG_SYS_FSL_I2C4_SLAVE 0x7F 481 #define CONFIG_SYS_FSL_I2C_OFFSET 0x118000 482 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100 483 #define CONFIG_SYS_FSL_I2C3_OFFSET 0x119000 484 #define CONFIG_SYS_FSL_I2C4_OFFSET 0x119100 485 #define CONFIG_SYS_FSL_I2C_SPEED 100000 486 #define CONFIG_SYS_FSL_I2C2_SPEED 100000 487 #define CONFIG_SYS_FSL_I2C3_SPEED 100000 488 #define CONFIG_SYS_FSL_I2C4_SPEED 100000 489 #define I2C_MUX_PCA_ADDR_PRI 0x77 /* I2C bus multiplexer,primary */ 490 #define I2C_MUX_PCA_ADDR_SEC1 0x75 /* I2C bus multiplexer,secondary 1 */ 491 #define I2C_MUX_PCA_ADDR_SEC2 0x76 /* I2C bus multiplexer,secondary 2 */ 492 #define I2C_MUX_CH_DEFAULT 0x8 493 494 495 /* 496 * RapidIO 497 */ 498 #define CONFIG_SYS_SRIO1_MEM_VIRT 0xa0000000 499 #define CONFIG_SYS_SRIO1_MEM_PHYS 0xc20000000ull 500 #define CONFIG_SYS_SRIO1_MEM_SIZE 0x10000000 /* 256M */ 501 #define CONFIG_SYS_SRIO2_MEM_VIRT 0xb0000000 502 #define CONFIG_SYS_SRIO2_MEM_PHYS 0xc30000000ull 503 #define CONFIG_SYS_SRIO2_MEM_SIZE 0x10000000 /* 256M */ 504 /* 505 * for slave u-boot IMAGE instored in master memory space, 506 * PHYS must be aligned based on the SIZE 507 */ 508 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef080000ull 509 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff80000ull 510 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x80000 /* 512K */ 511 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff80000ull 512 /* 513 * for slave UCODE and ENV instored in master memory space, 514 * PHYS must be aligned based on the SIZE 515 */ 516 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef040000ull 517 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull 518 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */ 519 520 /* slave core release by master*/ 521 #define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4 522 #define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */ 523 524 /* 525 * SRIO_PCIE_BOOT - SLAVE 526 */ 527 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE 528 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000 529 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \ 530 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR) 531 #endif 532 533 /* 534 * eSPI - Enhanced SPI 535 */ 536 #ifdef CONFIG_SPI_FLASH 537 #define CONFIG_FSL_ESPI 538 #define CONFIG_SPI_FLASH_STMICRO 539 #if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_RAMBOOT_PBL) 540 #define CONFIG_SPI_FLASH_SST 541 #define CONFIG_SPI_FLASH_EON 542 #endif 543 544 #define CONFIG_CMD_SF 545 #define CONFIG_SPI_FLASH_BAR 546 #define CONFIG_SF_DEFAULT_SPEED 10000000 547 #define CONFIG_SF_DEFAULT_MODE 0 548 #endif 549 550 /* 551 * General PCI 552 * Memory space is mapped 1-1, but I/O space must start from 0. 553 */ 554 #define CONFIG_PCI /* Enable PCI/PCIE */ 555 #define CONFIG_PCIE1 /* PCIE controler 1 */ 556 #define CONFIG_PCIE2 /* PCIE controler 2 */ 557 #define CONFIG_PCIE3 /* PCIE controler 3 */ 558 #define CONFIG_PCIE4 /* PCIE controler 4 */ 559 #define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ 560 #define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ 561 /* controller 1, direct to uli, tgtid 3, Base address 20000 */ 562 #define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 563 #define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 564 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull 565 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ 566 #define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000 567 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 568 #define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull 569 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ 570 571 /* controller 2, Slot 2, tgtid 2, Base address 201000 */ 572 #define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 573 #define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000 574 #define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull 575 #define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */ 576 #define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000 577 #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 578 #define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull 579 #define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ 580 581 /* controller 3, Slot 1, tgtid 1, Base address 202000 */ 582 #define CONFIG_SYS_PCIE3_MEM_VIRT 0xb0000000 583 #define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000 584 #define CONFIG_SYS_PCIE3_MEM_PHYS 0xc30000000ull 585 #define CONFIG_SYS_PCIE3_MEM_SIZE 0x10000000 /* 256M */ 586 #define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000 587 #define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 588 #define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull 589 #define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */ 590 591 /* controller 4, Base address 203000 */ 592 #define CONFIG_SYS_PCIE4_MEM_VIRT 0xc0000000 593 #define CONFIG_SYS_PCIE4_MEM_BUS 0xe0000000 594 #define CONFIG_SYS_PCIE4_MEM_PHYS 0xc40000000ull 595 #define CONFIG_SYS_PCIE4_MEM_SIZE 0x10000000 /* 256M */ 596 #define CONFIG_SYS_PCIE4_IO_BUS 0x00000000 597 #define CONFIG_SYS_PCIE4_IO_PHYS 0xff8030000ull 598 #define CONFIG_SYS_PCIE4_IO_SIZE 0x00010000 /* 64k */ 599 600 #ifdef CONFIG_PCI 601 #define CONFIG_PCI_INDIRECT_BRIDGE 602 #define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata */ 603 #define CONFIG_NET_MULTI 604 #define CONFIG_E1000 605 #define CONFIG_PCI_PNP /* do pci plug-and-play */ 606 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 607 #define CONFIG_DOS_PARTITION 608 #endif 609 610 /* Qman/Bman */ 611 #ifndef CONFIG_NOBQFMAN 612 #define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */ 613 #define CONFIG_SYS_BMAN_NUM_PORTALS 18 614 #define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000 615 #define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull 616 #define CONFIG_SYS_BMAN_MEM_SIZE 0x02000000 617 #define CONFIG_SYS_QMAN_NUM_PORTALS 18 618 #define CONFIG_SYS_QMAN_MEM_BASE 0xf6000000 619 #define CONFIG_SYS_QMAN_MEM_PHYS 0xff6000000ull 620 #define CONFIG_SYS_QMAN_MEM_SIZE 0x02000000 621 622 #define CONFIG_SYS_DPAA_FMAN 623 #define CONFIG_SYS_DPAA_PME 624 #define CONFIG_SYS_PMAN 625 #define CONFIG_SYS_DPAA_DCE 626 #define CONFIG_SYS_DPAA_RMAN /* RMan */ 627 #define CONFIG_SYS_INTERLAKEN 628 629 /* Default address of microcode for the Linux Fman driver */ 630 #if defined(CONFIG_SPIFLASH) 631 /* 632 * env is stored at 0x100000, sector size is 0x10000, ucode is stored after 633 * env, so we got 0x110000. 634 */ 635 #define CONFIG_SYS_QE_FW_IN_SPIFLASH 636 #define CONFIG_SYS_FMAN_FW_ADDR 0x110000 637 #elif defined(CONFIG_SDCARD) 638 /* 639 * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is 640 * about 1MB (2048 blocks), Env is stored after the image, and the env size is 641 * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080. 642 */ 643 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC 644 #define CONFIG_SYS_FMAN_FW_ADDR (512 * 0x820) 645 #elif defined(CONFIG_NAND) 646 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND 647 #define CONFIG_SYS_FMAN_FW_ADDR (11 * CONFIG_SYS_NAND_BLOCK_SIZE) 648 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) 649 /* 650 * Slave has no ucode locally, it can fetch this from remote. When implementing 651 * in two corenet boards, slave's ucode could be stored in master's memory 652 * space, the address can be mapped from slave TLB->slave LAW-> 653 * slave SRIO or PCIE outbound window->master inbound window-> 654 * master LAW->the ucode address in master's memory space. 655 */ 656 #define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE 657 #define CONFIG_SYS_FMAN_FW_ADDR 0xFFE00000 658 #else 659 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR 660 #define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000 661 #endif 662 #define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 663 #define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) 664 #endif /* CONFIG_NOBQFMAN */ 665 666 #ifdef CONFIG_SYS_DPAA_FMAN 667 #define CONFIG_FMAN_ENET 668 #define CONFIG_PHYLIB_10G 669 #define CONFIG_PHY_VITESSE 670 #define CONFIG_PHY_REALTEK 671 #define CONFIG_PHY_TERANETICS 672 #define RGMII_PHY1_ADDR 0x1 673 #define RGMII_PHY2_ADDR 0x2 674 #define FM1_10GEC1_PHY_ADDR 0x3 675 #define SGMII_CARD_PORT1_PHY_ADDR 0x1C 676 #define SGMII_CARD_PORT2_PHY_ADDR 0x1D 677 #define SGMII_CARD_PORT3_PHY_ADDR 0x1E 678 #define SGMII_CARD_PORT4_PHY_ADDR 0x1F 679 #endif 680 681 #ifdef CONFIG_FMAN_ENET 682 #define CONFIG_MII /* MII PHY management */ 683 #define CONFIG_ETHPRIME "FM1@DTSEC3" 684 #define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ 685 #endif 686 687 /* 688 * SATA 689 */ 690 #ifdef CONFIG_FSL_SATA_V2 691 #define CONFIG_LIBATA 692 #define CONFIG_FSL_SATA 693 #define CONFIG_SYS_SATA_MAX_DEVICE 2 694 #define CONFIG_SATA1 695 #define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR 696 #define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA 697 #define CONFIG_SATA2 698 #define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR 699 #define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA 700 #define CONFIG_LBA48 701 #define CONFIG_CMD_SATA 702 #define CONFIG_DOS_PARTITION 703 #define CONFIG_CMD_EXT2 704 #endif 705 706 /* 707 * USB 708 */ 709 #ifdef CONFIG_USB_EHCI 710 #define CONFIG_CMD_USB 711 #define CONFIG_USB_STORAGE 712 #define CONFIG_USB_EHCI_FSL 713 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET 714 #define CONFIG_CMD_EXT2 715 #define CONFIG_HAS_FSL_DR_USB 716 #endif 717 718 /* 719 * SDHC 720 */ 721 #ifdef CONFIG_MMC 722 #define CONFIG_CMD_MMC 723 #define CONFIG_FSL_ESDHC 724 #define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR 725 #define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT 726 #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33 727 #define CONFIG_GENERIC_MMC 728 #define CONFIG_CMD_EXT2 729 #define CONFIG_CMD_FAT 730 #define CONFIG_DOS_PARTITION 731 #endif 732 733 734 /* 735 * Dynamic MTD Partition support with mtdparts 736 */ 737 #ifndef CONFIG_SYS_NO_FLASH 738 #define CONFIG_MTD_DEVICE 739 #define CONFIG_MTD_PARTITIONS 740 #define CONFIG_CMD_MTDPARTS 741 #define CONFIG_FLASH_CFI_MTD 742 #define MTDIDS_DEFAULT "nor0=fe8000000.nor,nand0=fff800000.flash," \ 743 "spi0=spife110000.0" 744 #define MTDPARTS_DEFAULT "mtdparts=fe8000000.nor:1m(uboot),5m(kernel)," \ 745 "128k(dtb),96m(fs),-(user);fff800000.flash:1m(uboot)," \ 746 "5m(kernel),128k(dtb),96m(fs),-(user);spife110000.0:" \ 747 "1m(uboot),5m(kernel),128k(dtb),-(user)" 748 #endif 749 750 /* 751 * Environment 752 */ 753 #define CONFIG_LOADS_ECHO /* echo on for serial download */ 754 #define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ 755 756 /* 757 * Command line configuration. 758 */ 759 #include <config_cmd_default.h> 760 761 #define CONFIG_CMD_DHCP 762 #define CONFIG_CMD_ELF 763 #define CONFIG_CMD_ERRATA 764 #define CONFIG_CMD_GREPENV 765 #define CONFIG_CMD_IRQ 766 #define CONFIG_CMD_I2C 767 #define CONFIG_CMD_MII 768 #define CONFIG_CMD_PING 769 #define CONFIG_CMD_SETEXPR 770 #define CONFIG_CMD_REGINFO 771 #define CONFIG_CMD_BDI 772 773 #ifdef CONFIG_PCI 774 #define CONFIG_CMD_PCI 775 #define CONFIG_CMD_NET 776 #endif 777 778 /* 779 * Miscellaneous configurable options 780 */ 781 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 782 #define CONFIG_CMDLINE_EDITING /* Command-line editing */ 783 #define CONFIG_AUTO_COMPLETE /* add autocompletion support */ 784 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 785 #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ 786 #ifdef CONFIG_CMD_KGDB 787 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 788 #else 789 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 790 #endif 791 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) 792 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 793 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */ 794 795 /* 796 * For booting Linux, the board info and command line data 797 * have to be in the first 64 MB of memory, since this is 798 * the maximum mapped by the Linux kernel during initialization. 799 */ 800 #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial map for Linux*/ 801 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 802 803 #ifdef CONFIG_CMD_KGDB 804 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ 805 #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ 806 #endif 807 808 /* 809 * Environment Configuration 810 */ 811 #define CONFIG_ROOTPATH "/opt/nfsroot" 812 #define CONFIG_BOOTFILE "uImage" 813 #define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server */ 814 815 /* default location for tftp and bootm */ 816 #define CONFIG_LOADADDR 1000000 817 #define CONFIG_BAUDRATE 115200 818 #define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ 819 #define __USB_PHY_TYPE utmi 820 821 #define CONFIG_EXTRA_ENV_SETTINGS \ 822 "hwconfig=fsl_ddr:" \ 823 "ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) "," \ 824 "bank_intlv=auto;" \ 825 "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\ 826 "netdev=eth0\0" \ 827 "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ 828 "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \ 829 "tftpflash=tftpboot $loadaddr $uboot && " \ 830 "protect off $ubootaddr +$filesize && " \ 831 "erase $ubootaddr +$filesize && " \ 832 "cp.b $loadaddr $ubootaddr $filesize && " \ 833 "protect on $ubootaddr +$filesize && " \ 834 "cmp.b $loadaddr $ubootaddr $filesize\0" \ 835 "consoledev=ttyS0\0" \ 836 "ramdiskaddr=2000000\0" \ 837 "ramdiskfile=t2080qds/ramdisk.uboot\0" \ 838 "fdtaddr=c00000\0" \ 839 "fdtfile=t2080qds/t2080qds.dtb\0" \ 840 "bdev=sda3\0" \ 841 "c=ffe\0" 842 843 /* 844 * For emulation this causes u-boot to jump to the start of the 845 * proof point app code automatically 846 */ 847 #define CONFIG_PROOF_POINTS \ 848 "setenv bootargs root=/dev/$bdev rw " \ 849 "console=$consoledev,$baudrate $othbootargs;" \ 850 "cpu 1 release 0x29000000 - - -;" \ 851 "cpu 2 release 0x29000000 - - -;" \ 852 "cpu 3 release 0x29000000 - - -;" \ 853 "cpu 4 release 0x29000000 - - -;" \ 854 "cpu 5 release 0x29000000 - - -;" \ 855 "cpu 6 release 0x29000000 - - -;" \ 856 "cpu 7 release 0x29000000 - - -;" \ 857 "go 0x29000000" 858 859 #define CONFIG_HVBOOT \ 860 "setenv bootargs config-addr=0x60000000; " \ 861 "bootm 0x01000000 - 0x00f00000" 862 863 #define CONFIG_ALU \ 864 "setenv bootargs root=/dev/$bdev rw " \ 865 "console=$consoledev,$baudrate $othbootargs;" \ 866 "cpu 1 release 0x01000000 - - -;" \ 867 "cpu 2 release 0x01000000 - - -;" \ 868 "cpu 3 release 0x01000000 - - -;" \ 869 "cpu 4 release 0x01000000 - - -;" \ 870 "cpu 5 release 0x01000000 - - -;" \ 871 "cpu 6 release 0x01000000 - - -;" \ 872 "cpu 7 release 0x01000000 - - -;" \ 873 "go 0x01000000" 874 875 #define CONFIG_LINUX \ 876 "setenv bootargs root=/dev/ram rw " \ 877 "console=$consoledev,$baudrate $othbootargs;" \ 878 "setenv ramdiskaddr 0x02000000;" \ 879 "setenv fdtaddr 0x00c00000;" \ 880 "setenv loadaddr 0x1000000;" \ 881 "bootm $loadaddr $ramdiskaddr $fdtaddr" 882 883 #define CONFIG_HDBOOT \ 884 "setenv bootargs root=/dev/$bdev rw " \ 885 "console=$consoledev,$baudrate $othbootargs;" \ 886 "tftp $loadaddr $bootfile;" \ 887 "tftp $fdtaddr $fdtfile;" \ 888 "bootm $loadaddr - $fdtaddr" 889 890 #define CONFIG_NFSBOOTCOMMAND \ 891 "setenv bootargs root=/dev/nfs rw " \ 892 "nfsroot=$serverip:$rootpath " \ 893 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 894 "console=$consoledev,$baudrate $othbootargs;" \ 895 "tftp $loadaddr $bootfile;" \ 896 "tftp $fdtaddr $fdtfile;" \ 897 "bootm $loadaddr - $fdtaddr" 898 899 #define CONFIG_RAMBOOTCOMMAND \ 900 "setenv bootargs root=/dev/ram rw " \ 901 "console=$consoledev,$baudrate $othbootargs;" \ 902 "tftp $ramdiskaddr $ramdiskfile;" \ 903 "tftp $loadaddr $bootfile;" \ 904 "tftp $fdtaddr $fdtfile;" \ 905 "bootm $loadaddr $ramdiskaddr $fdtaddr" 906 907 #define CONFIG_BOOTCOMMAND CONFIG_LINUX 908 909 #ifdef CONFIG_SECURE_BOOT 910 #include <asm/fsl_secure_boot.h> 911 #undef CONFIG_CMD_USB 912 #endif 913 914 #endif /* __T208xQDS_H */ 915