1 /* 2 * Copyright 2011-2013 Freescale Semiconductor, Inc. 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 /* 8 * T2080/T2081 QDS board configuration file 9 */ 10 11 #ifndef __T208xQDS_H 12 #define __T208xQDS_H 13 14 #define CONFIG_ICS307_REFCLK_HZ 25000000 /* ICS307 ref clk freq */ 15 #if defined(CONFIG_ARCH_T2080) 16 #define CONFIG_FSL_SATA_V2 17 #define CONFIG_SYS_SRIO /* Enable Serial RapidIO Support */ 18 #define CONFIG_SRIO1 /* SRIO port 1 */ 19 #define CONFIG_SRIO2 /* SRIO port 2 */ 20 #elif defined(CONFIG_ARCH_T2081) 21 #endif 22 23 /* High Level Configuration Options */ 24 #define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */ 25 #define CONFIG_MP /* support multiple processors */ 26 #define CONFIG_ENABLE_36BIT_PHYS 27 28 #ifdef CONFIG_PHYS_64BIT 29 #define CONFIG_ADDR_MAP 1 30 #define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */ 31 #endif 32 33 #define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */ 34 #define CONFIG_SYS_NUM_CPC CONFIG_SYS_NUM_DDR_CTLRS 35 #define CONFIG_ENV_OVERWRITE 36 37 #ifdef CONFIG_RAMBOOT_PBL 38 #define CONFIG_SYS_FSL_PBL_PBI board/freescale/t208xqds/t208x_pbi.cfg 39 40 #define CONFIG_SPL_FLUSH_IMAGE 41 #define CONFIG_SPL_TARGET "u-boot-with-spl.bin" 42 #define CONFIG_SYS_TEXT_BASE 0x00201000 43 #define CONFIG_SPL_TEXT_BASE 0xFFFD8000 44 #define CONFIG_SPL_PAD_TO 0x40000 45 #define CONFIG_SPL_MAX_SIZE 0x28000 46 #define RESET_VECTOR_OFFSET 0x27FFC 47 #define BOOT_PAGE_OFFSET 0x27000 48 #ifdef CONFIG_SPL_BUILD 49 #define CONFIG_SPL_SKIP_RELOCATE 50 #define CONFIG_SPL_COMMON_INIT_DDR 51 #define CONFIG_SYS_CCSR_DO_NOT_RELOCATE 52 #endif 53 54 #ifdef CONFIG_NAND 55 #define CONFIG_SYS_NAND_U_BOOT_SIZE (768 << 10) 56 #define CONFIG_SYS_NAND_U_BOOT_DST 0x00200000 57 #define CONFIG_SYS_NAND_U_BOOT_START 0x00200000 58 #define CONFIG_SYS_NAND_U_BOOT_OFFS (256 << 10) 59 #define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot-nand.lds" 60 #if defined(CONFIG_ARCH_T2080) 61 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xqds/t2080_nand_rcw.cfg 62 #elif defined(CONFIG_ARCH_T2081) 63 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xqds/t2081_nand_rcw.cfg 64 #endif 65 #define CONFIG_SPL_NAND_BOOT 66 #endif 67 68 #ifdef CONFIG_SPIFLASH 69 #define CONFIG_RESET_VECTOR_ADDRESS 0x200FFC 70 #define CONFIG_SPL_SPI_FLASH_MINIMAL 71 #define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE (768 << 10) 72 #define CONFIG_SYS_SPI_FLASH_U_BOOT_DST (0x00200000) 73 #define CONFIG_SYS_SPI_FLASH_U_BOOT_START (0x00200000) 74 #define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS (256 << 10) 75 #define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot.lds" 76 #ifndef CONFIG_SPL_BUILD 77 #define CONFIG_SYS_MPC85XX_NO_RESETVEC 78 #endif 79 #if defined(CONFIG_ARCH_T2080) 80 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xqds/t2080_spi_rcw.cfg 81 #elif defined(CONFIG_ARCH_T2081) 82 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xqds/t2081_spi_rcw.cfg 83 #endif 84 #define CONFIG_SPL_SPI_BOOT 85 #endif 86 87 #ifdef CONFIG_SDCARD 88 #define CONFIG_RESET_VECTOR_ADDRESS 0x200FFC 89 #define CONFIG_SPL_MMC_MINIMAL 90 #define CONFIG_SYS_MMC_U_BOOT_SIZE (768 << 10) 91 #define CONFIG_SYS_MMC_U_BOOT_DST (0x00200000) 92 #define CONFIG_SYS_MMC_U_BOOT_START (0x00200000) 93 #define CONFIG_SYS_MMC_U_BOOT_OFFS (260 << 10) 94 #define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot.lds" 95 #ifndef CONFIG_SPL_BUILD 96 #define CONFIG_SYS_MPC85XX_NO_RESETVEC 97 #endif 98 #if defined(CONFIG_ARCH_T2080) 99 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xqds/t2080_sd_rcw.cfg 100 #elif defined(CONFIG_ARCH_T2081) 101 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xqds/t2081_sd_rcw.cfg 102 #endif 103 #define CONFIG_SPL_MMC_BOOT 104 #endif 105 106 #endif /* CONFIG_RAMBOOT_PBL */ 107 108 #define CONFIG_SRIO_PCIE_BOOT_MASTER 109 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE 110 /* Set 1M boot space */ 111 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000) 112 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \ 113 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR) 114 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc 115 #endif 116 117 #ifndef CONFIG_SYS_TEXT_BASE 118 #define CONFIG_SYS_TEXT_BASE 0xeff40000 119 #endif 120 121 #ifndef CONFIG_RESET_VECTOR_ADDRESS 122 #define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc 123 #endif 124 125 /* 126 * These can be toggled for performance analysis, otherwise use default. 127 */ 128 #define CONFIG_SYS_CACHE_STASHING 129 #define CONFIG_BTB /* toggle branch predition */ 130 #define CONFIG_DDR_ECC 131 #ifdef CONFIG_DDR_ECC 132 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER 133 #define CONFIG_MEM_INIT_VALUE 0xdeadbeef 134 #endif 135 136 #ifdef CONFIG_MTD_NOR_FLASH 137 #define CONFIG_FLASH_CFI_DRIVER 138 #define CONFIG_SYS_FLASH_CFI 139 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 140 #endif 141 142 #if defined(CONFIG_SPIFLASH) 143 #define CONFIG_SYS_EXTRA_ENV_RELOC 144 #define CONFIG_ENV_SPI_BUS 0 145 #define CONFIG_ENV_SPI_CS 0 146 #define CONFIG_ENV_SPI_MAX_HZ 10000000 147 #define CONFIG_ENV_SPI_MODE 0 148 #define CONFIG_ENV_SIZE 0x2000 /* 8KB */ 149 #define CONFIG_ENV_OFFSET 0x100000 /* 1MB */ 150 #define CONFIG_ENV_SECT_SIZE 0x10000 151 #elif defined(CONFIG_SDCARD) 152 #define CONFIG_SYS_EXTRA_ENV_RELOC 153 #define CONFIG_SYS_MMC_ENV_DEV 0 154 #define CONFIG_ENV_SIZE 0x2000 155 #define CONFIG_ENV_OFFSET (512 * 0x800) 156 #elif defined(CONFIG_NAND) 157 #define CONFIG_SYS_EXTRA_ENV_RELOC 158 #define CONFIG_ENV_SIZE 0x2000 159 #define CONFIG_ENV_OFFSET (10 * CONFIG_SYS_NAND_BLOCK_SIZE) 160 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) 161 #define CONFIG_ENV_ADDR 0xffe20000 162 #define CONFIG_ENV_SIZE 0x2000 163 #elif defined(CONFIG_ENV_IS_NOWHERE) 164 #define CONFIG_ENV_SIZE 0x2000 165 #else 166 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) 167 #define CONFIG_ENV_SIZE 0x2000 168 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ 169 #endif 170 171 #ifndef __ASSEMBLY__ 172 unsigned long get_board_sys_clk(void); 173 unsigned long get_board_ddr_clk(void); 174 #endif 175 176 #define CONFIG_SYS_CLK_FREQ get_board_sys_clk() 177 #define CONFIG_DDR_CLK_FREQ get_board_ddr_clk() 178 179 /* 180 * Config the L3 Cache as L3 SRAM 181 */ 182 #define CONFIG_SYS_INIT_L3_ADDR 0xFFFC0000 183 #define CONFIG_SYS_L3_SIZE (512 << 10) 184 #define CONFIG_SPL_GD_ADDR (CONFIG_SYS_INIT_L3_ADDR + 32 * 1024) 185 #ifdef CONFIG_RAMBOOT_PBL 186 #define CONFIG_ENV_ADDR (CONFIG_SPL_GD_ADDR + 4 * 1024) 187 #endif 188 #define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SPL_GD_ADDR + 12 * 1024) 189 #define CONFIG_SPL_RELOC_MALLOC_SIZE (50 << 10) 190 #define CONFIG_SPL_RELOC_STACK (CONFIG_SPL_GD_ADDR + 64 * 1024) 191 #define CONFIG_SPL_RELOC_STACK_SIZE (22 << 10) 192 193 #define CONFIG_SYS_DCSRBAR 0xf0000000 194 #define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull 195 196 /* EEPROM */ 197 #define CONFIG_ID_EEPROM 198 #define CONFIG_SYS_I2C_EEPROM_NXID 199 #define CONFIG_SYS_EEPROM_BUS_NUM 0 200 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 201 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 202 203 /* 204 * DDR Setup 205 */ 206 #define CONFIG_VERY_BIG_RAM 207 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 208 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 209 #define CONFIG_DIMM_SLOTS_PER_CTLR 2 210 #define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR) 211 #define CONFIG_FSL_DDR_FIRST_SLOT_QUAD_CAPABLE 212 #define CONFIG_DDR_SPD 213 #define CONFIG_FSL_DDR_INTERACTIVE 214 #define CONFIG_SYS_SPD_BUS_NUM 0 215 #define CONFIG_SYS_SDRAM_SIZE 2048 /* for fixed parameter use */ 216 #define SPD_EEPROM_ADDRESS1 0x51 217 #define SPD_EEPROM_ADDRESS2 0x52 218 #define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1 219 #define CTRL_INTLV_PREFERED cacheline 220 221 /* 222 * IFC Definitions 223 */ 224 #define CONFIG_SYS_FLASH_BASE 0xe0000000 225 #define CONFIG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CONFIG_SYS_FLASH_BASE) 226 #define CONFIG_SYS_NOR0_CSPR_EXT (0xf) 227 #define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS \ 228 + 0x8000000) | \ 229 CSPR_PORT_SIZE_16 | \ 230 CSPR_MSEL_NOR | \ 231 CSPR_V) 232 #define CONFIG_SYS_NOR1_CSPR_EXT (0xf) 233 #define CONFIG_SYS_NOR1_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \ 234 CSPR_PORT_SIZE_16 | \ 235 CSPR_MSEL_NOR | \ 236 CSPR_V) 237 #define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024) 238 /* NOR Flash Timing Params */ 239 #define CONFIG_SYS_NOR_CSOR CSOR_NAND_TRHZ_80 240 241 #define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \ 242 FTIM0_NOR_TEADC(0x5) | \ 243 FTIM0_NOR_TEAHC(0x5)) 244 #define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \ 245 FTIM1_NOR_TRAD_NOR(0x1A) |\ 246 FTIM1_NOR_TSEQRAD_NOR(0x13)) 247 #define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \ 248 FTIM2_NOR_TCH(0x4) | \ 249 FTIM2_NOR_TWPH(0x0E) | \ 250 FTIM2_NOR_TWP(0x1c)) 251 #define CONFIG_SYS_NOR_FTIM3 0x0 252 253 #define CONFIG_SYS_FLASH_QUIET_TEST 254 #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ 255 256 #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ 257 #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ 258 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 259 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 260 261 #define CONFIG_SYS_FLASH_EMPTY_INFO 262 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS \ 263 + 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS} 264 265 #define CONFIG_FSL_QIXIS /* use common QIXIS code */ 266 #define QIXIS_BASE 0xffdf0000 267 #define QIXIS_LBMAP_SWITCH 6 268 #define QIXIS_LBMAP_MASK 0x0f 269 #define QIXIS_LBMAP_SHIFT 0 270 #define QIXIS_LBMAP_DFLTBANK 0x00 271 #define QIXIS_LBMAP_ALTBANK 0x04 272 #define QIXIS_LBMAP_NAND 0x09 273 #define QIXIS_LBMAP_SD 0x00 274 #define QIXIS_RCW_SRC_NAND 0x104 275 #define QIXIS_RCW_SRC_SD 0x040 276 #define QIXIS_RST_CTL_RESET 0x83 277 #define QIXIS_RST_FORCE_MEM 0x1 278 #define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20 279 #define QIXIS_RCFG_CTL_RECONFIG_START 0x21 280 #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08 281 #define QIXIS_BASE_PHYS (0xf00000000ull | QIXIS_BASE) 282 283 #define CONFIG_SYS_CSPR3_EXT (0xf) 284 #define CONFIG_SYS_CSPR3 (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \ 285 | CSPR_PORT_SIZE_8 \ 286 | CSPR_MSEL_GPCM \ 287 | CSPR_V) 288 #define CONFIG_SYS_AMASK3 IFC_AMASK(4*1024) 289 #define CONFIG_SYS_CSOR3 0x0 290 /* QIXIS Timing parameters for IFC CS3 */ 291 #define CONFIG_SYS_CS3_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \ 292 FTIM0_GPCM_TEADC(0x0e) | \ 293 FTIM0_GPCM_TEAHC(0x0e)) 294 #define CONFIG_SYS_CS3_FTIM1 (FTIM1_GPCM_TACO(0xff) | \ 295 FTIM1_GPCM_TRAD(0x3f)) 296 #define CONFIG_SYS_CS3_FTIM2 (FTIM2_GPCM_TCS(0x0e) | \ 297 FTIM2_GPCM_TCH(0x8) | \ 298 FTIM2_GPCM_TWP(0x1f)) 299 #define CONFIG_SYS_CS3_FTIM3 0x0 300 301 /* NAND Flash on IFC */ 302 #define CONFIG_NAND_FSL_IFC 303 #define CONFIG_SYS_NAND_BASE 0xff800000 304 #define CONFIG_SYS_NAND_BASE_PHYS (0xf00000000ull | CONFIG_SYS_NAND_BASE) 305 306 #define CONFIG_SYS_NAND_CSPR_EXT (0xf) 307 #define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ 308 | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \ 309 | CSPR_MSEL_NAND /* MSEL = NAND */ \ 310 | CSPR_V) 311 #define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024) 312 313 #define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \ 314 | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \ 315 | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \ 316 | CSOR_NAND_RAL_3 /* RAL = 2Byes */ \ 317 | CSOR_NAND_PGS_2K /* Page Size = 2K */\ 318 | CSOR_NAND_SPRZ_64 /* Spare size = 64 */\ 319 | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/ 320 321 #define CONFIG_SYS_NAND_ONFI_DETECTION 322 323 /* ONFI NAND Flash mode0 Timing Params */ 324 #define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \ 325 FTIM0_NAND_TWP(0x18) | \ 326 FTIM0_NAND_TWCHT(0x07) | \ 327 FTIM0_NAND_TWH(0x0a)) 328 #define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \ 329 FTIM1_NAND_TWBE(0x39) | \ 330 FTIM1_NAND_TRR(0x0e) | \ 331 FTIM1_NAND_TRP(0x18)) 332 #define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \ 333 FTIM2_NAND_TREH(0x0a) | \ 334 FTIM2_NAND_TWHRE(0x1e)) 335 #define CONFIG_SYS_NAND_FTIM3 0x0 336 337 #define CONFIG_SYS_NAND_DDR_LAW 11 338 #define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } 339 #define CONFIG_SYS_MAX_NAND_DEVICE 1 340 #define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) 341 342 #if defined(CONFIG_NAND) 343 #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT 344 #define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR 345 #define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK 346 #define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR 347 #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0 348 #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1 349 #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2 350 #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3 351 #define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR0_CSPR_EXT 352 #define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR0_CSPR 353 #define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK 354 #define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR 355 #define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0 356 #define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1 357 #define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2 358 #define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3 359 #define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NOR1_CSPR_EXT 360 #define CONFIG_SYS_CSPR2 CONFIG_SYS_NOR1_CSPR 361 #define CONFIG_SYS_AMASK2 CONFIG_SYS_NOR_AMASK 362 #define CONFIG_SYS_CSOR2 CONFIG_SYS_NOR_CSOR 363 #define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NOR_FTIM0 364 #define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NOR_FTIM1 365 #define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NOR_FTIM2 366 #define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NOR_FTIM3 367 #else 368 #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT 369 #define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR 370 #define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK 371 #define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR 372 #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0 373 #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1 374 #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2 375 #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3 376 #define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR1_CSPR_EXT 377 #define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR1_CSPR 378 #define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK 379 #define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR 380 #define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0 381 #define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1 382 #define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2 383 #define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3 384 #define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NAND_CSPR_EXT 385 #define CONFIG_SYS_CSPR2 CONFIG_SYS_NAND_CSPR 386 #define CONFIG_SYS_AMASK2 CONFIG_SYS_NAND_AMASK 387 #define CONFIG_SYS_CSOR2 CONFIG_SYS_NAND_CSOR 388 #define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NAND_FTIM0 389 #define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NAND_FTIM1 390 #define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NAND_FTIM2 391 #define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NAND_FTIM3 392 #endif 393 394 #if defined(CONFIG_RAMBOOT_PBL) 395 #define CONFIG_SYS_RAMBOOT 396 #endif 397 398 #ifdef CONFIG_SPL_BUILD 399 #define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE 400 #else 401 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 402 #endif 403 404 #define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */ 405 #define CONFIG_MISC_INIT_R 406 #define CONFIG_HWCONFIG 407 408 /* define to use L1 as initial stack */ 409 #define CONFIG_L1_INIT_RAM 410 #define CONFIG_SYS_INIT_RAM_LOCK 411 #define CONFIG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */ 412 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf 413 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW 0xfe03c000 414 /* The assembler doesn't like typecast */ 415 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \ 416 ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \ 417 CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW) 418 #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 419 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ 420 GENERATED_GBL_DATA_SIZE) 421 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 422 #define CONFIG_SYS_MONITOR_LEN (768 * 1024) 423 #define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024) 424 425 /* 426 * Serial Port 427 */ 428 #define CONFIG_CONS_INDEX 1 429 #define CONFIG_SYS_NS16550_SERIAL 430 #define CONFIG_SYS_NS16550_REG_SIZE 1 431 #define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2) 432 #define CONFIG_SYS_BAUDRATE_TABLE \ 433 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} 434 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500) 435 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600) 436 #define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500) 437 #define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600) 438 439 /* 440 * I2C 441 */ 442 #define CONFIG_SYS_I2C 443 #define CONFIG_SYS_I2C_FSL 444 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 445 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F 446 #define CONFIG_SYS_FSL_I2C3_SLAVE 0x7F 447 #define CONFIG_SYS_FSL_I2C4_SLAVE 0x7F 448 #define CONFIG_SYS_FSL_I2C_OFFSET 0x118000 449 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100 450 #define CONFIG_SYS_FSL_I2C3_OFFSET 0x119000 451 #define CONFIG_SYS_FSL_I2C4_OFFSET 0x119100 452 #define CONFIG_SYS_FSL_I2C_SPEED 100000 453 #define CONFIG_SYS_FSL_I2C2_SPEED 100000 454 #define CONFIG_SYS_FSL_I2C3_SPEED 100000 455 #define CONFIG_SYS_FSL_I2C4_SPEED 100000 456 #define I2C_MUX_PCA_ADDR_PRI 0x77 /* I2C bus multiplexer,primary */ 457 #define I2C_MUX_PCA_ADDR_SEC1 0x75 /* I2C bus multiplexer,secondary 1 */ 458 #define I2C_MUX_PCA_ADDR_SEC2 0x76 /* I2C bus multiplexer,secondary 2 */ 459 #define I2C_MUX_CH_DEFAULT 0x8 460 461 #define I2C_MUX_CH_VOL_MONITOR 0xa 462 463 /* Voltage monitor on channel 2*/ 464 #define I2C_VOL_MONITOR_ADDR 0x40 465 #define I2C_VOL_MONITOR_BUS_V_OFFSET 0x2 466 #define I2C_VOL_MONITOR_BUS_V_OVF 0x1 467 #define I2C_VOL_MONITOR_BUS_V_SHIFT 3 468 469 #define CONFIG_VID_FLS_ENV "t208xqds_vdd_mv" 470 #ifndef CONFIG_SPL_BUILD 471 #define CONFIG_VID 472 #endif 473 #define CONFIG_VOL_MONITOR_IR36021_SET 474 #define CONFIG_VOL_MONITOR_IR36021_READ 475 /* The lowest and highest voltage allowed for T208xQDS */ 476 #define VDD_MV_MIN 819 477 #define VDD_MV_MAX 1212 478 479 /* 480 * RapidIO 481 */ 482 #define CONFIG_SYS_SRIO1_MEM_VIRT 0xa0000000 483 #define CONFIG_SYS_SRIO1_MEM_PHYS 0xc20000000ull 484 #define CONFIG_SYS_SRIO1_MEM_SIZE 0x10000000 /* 256M */ 485 #define CONFIG_SYS_SRIO2_MEM_VIRT 0xb0000000 486 #define CONFIG_SYS_SRIO2_MEM_PHYS 0xc30000000ull 487 #define CONFIG_SYS_SRIO2_MEM_SIZE 0x10000000 /* 256M */ 488 /* 489 * for slave u-boot IMAGE instored in master memory space, 490 * PHYS must be aligned based on the SIZE 491 */ 492 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull 493 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull 494 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x100000 /* 1M */ 495 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull 496 /* 497 * for slave UCODE and ENV instored in master memory space, 498 * PHYS must be aligned based on the SIZE 499 */ 500 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull 501 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull 502 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */ 503 504 /* slave core release by master*/ 505 #define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4 506 #define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */ 507 508 /* 509 * SRIO_PCIE_BOOT - SLAVE 510 */ 511 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE 512 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000 513 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \ 514 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR) 515 #endif 516 517 /* 518 * eSPI - Enhanced SPI 519 */ 520 #ifdef CONFIG_SPI_FLASH 521 #ifndef CONFIG_SPL_BUILD 522 #endif 523 524 #define CONFIG_SPI_FLASH_BAR 525 #define CONFIG_SF_DEFAULT_SPEED 10000000 526 #define CONFIG_SF_DEFAULT_MODE 0 527 #endif 528 529 /* 530 * General PCI 531 * Memory space is mapped 1-1, but I/O space must start from 0. 532 */ 533 #define CONFIG_PCIE1 /* PCIE controller 1 */ 534 #define CONFIG_PCIE2 /* PCIE controller 2 */ 535 #define CONFIG_PCIE3 /* PCIE controller 3 */ 536 #define CONFIG_PCIE4 /* PCIE controller 4 */ 537 #define CONFIG_FSL_PCIE_RESET 538 #define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ 539 #define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ 540 /* controller 1, direct to uli, tgtid 3, Base address 20000 */ 541 #define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 542 #define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 543 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull 544 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ 545 #define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000 546 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 547 #define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull 548 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ 549 550 /* controller 2, Slot 2, tgtid 2, Base address 201000 */ 551 #define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 552 #define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000 553 #define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull 554 #define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */ 555 #define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000 556 #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 557 #define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull 558 #define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ 559 560 /* controller 3, Slot 1, tgtid 1, Base address 202000 */ 561 #define CONFIG_SYS_PCIE3_MEM_VIRT 0xb0000000 562 #define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000 563 #define CONFIG_SYS_PCIE3_MEM_PHYS 0xc30000000ull 564 #define CONFIG_SYS_PCIE3_MEM_SIZE 0x10000000 /* 256M */ 565 #define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000 566 #define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 567 #define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull 568 #define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */ 569 570 /* controller 4, Base address 203000 */ 571 #define CONFIG_SYS_PCIE4_MEM_VIRT 0xc0000000 572 #define CONFIG_SYS_PCIE4_MEM_BUS 0xe0000000 573 #define CONFIG_SYS_PCIE4_MEM_PHYS 0xc40000000ull 574 #define CONFIG_SYS_PCIE4_MEM_SIZE 0x10000000 /* 256M */ 575 #define CONFIG_SYS_PCIE4_IO_BUS 0x00000000 576 #define CONFIG_SYS_PCIE4_IO_PHYS 0xff8030000ull 577 #define CONFIG_SYS_PCIE4_IO_SIZE 0x00010000 /* 64k */ 578 579 #ifdef CONFIG_PCI 580 #define CONFIG_PCI_INDIRECT_BRIDGE 581 #define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata */ 582 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 583 #endif 584 585 /* Qman/Bman */ 586 #ifndef CONFIG_NOBQFMAN 587 #define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */ 588 #define CONFIG_SYS_BMAN_NUM_PORTALS 18 589 #define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000 590 #define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull 591 #define CONFIG_SYS_BMAN_MEM_SIZE 0x02000000 592 #define CONFIG_SYS_BMAN_SP_CENA_SIZE 0x4000 593 #define CONFIG_SYS_BMAN_SP_CINH_SIZE 0x1000 594 #define CONFIG_SYS_BMAN_CENA_BASE CONFIG_SYS_BMAN_MEM_BASE 595 #define CONFIG_SYS_BMAN_CENA_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) 596 #define CONFIG_SYS_BMAN_CINH_BASE (CONFIG_SYS_BMAN_MEM_BASE + \ 597 CONFIG_SYS_BMAN_CENA_SIZE) 598 #define CONFIG_SYS_BMAN_CINH_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) 599 #define CONFIG_SYS_BMAN_SWP_ISDR_REG 0xE08 600 #define CONFIG_SYS_QMAN_NUM_PORTALS 18 601 #define CONFIG_SYS_QMAN_MEM_BASE 0xf6000000 602 #define CONFIG_SYS_QMAN_MEM_PHYS 0xff6000000ull 603 #define CONFIG_SYS_QMAN_MEM_SIZE 0x02000000 604 #define CONFIG_SYS_QMAN_SP_CENA_SIZE 0x4000 605 #define CONFIG_SYS_QMAN_SP_CINH_SIZE 0x1000 606 #define CONFIG_SYS_QMAN_CENA_BASE CONFIG_SYS_QMAN_MEM_BASE 607 #define CONFIG_SYS_QMAN_CENA_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) 608 #define CONFIG_SYS_QMAN_CINH_BASE (CONFIG_SYS_QMAN_MEM_BASE + \ 609 CONFIG_SYS_QMAN_CENA_SIZE) 610 #define CONFIG_SYS_QMAN_CINH_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) 611 #define CONFIG_SYS_QMAN_SWP_ISDR_REG 0xE08 612 613 #define CONFIG_SYS_DPAA_FMAN 614 #define CONFIG_SYS_DPAA_PME 615 #define CONFIG_SYS_PMAN 616 #define CONFIG_SYS_DPAA_DCE 617 #define CONFIG_SYS_DPAA_RMAN /* RMan */ 618 #define CONFIG_SYS_INTERLAKEN 619 620 /* Default address of microcode for the Linux Fman driver */ 621 #if defined(CONFIG_SPIFLASH) 622 /* 623 * env is stored at 0x100000, sector size is 0x10000, ucode is stored after 624 * env, so we got 0x110000. 625 */ 626 #define CONFIG_SYS_QE_FW_IN_SPIFLASH 627 #define CONFIG_SYS_FMAN_FW_ADDR 0x110000 628 #elif defined(CONFIG_SDCARD) 629 /* 630 * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is 631 * about 1MB (2048 blocks), Env is stored after the image, and the env size is 632 * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080. 633 */ 634 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC 635 #define CONFIG_SYS_FMAN_FW_ADDR (512 * 0x820) 636 #elif defined(CONFIG_NAND) 637 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND 638 #define CONFIG_SYS_FMAN_FW_ADDR (11 * CONFIG_SYS_NAND_BLOCK_SIZE) 639 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) 640 /* 641 * Slave has no ucode locally, it can fetch this from remote. When implementing 642 * in two corenet boards, slave's ucode could be stored in master's memory 643 * space, the address can be mapped from slave TLB->slave LAW-> 644 * slave SRIO or PCIE outbound window->master inbound window-> 645 * master LAW->the ucode address in master's memory space. 646 */ 647 #define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE 648 #define CONFIG_SYS_FMAN_FW_ADDR 0xFFE00000 649 #else 650 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR 651 #define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000 652 #endif 653 #define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 654 #define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) 655 #endif /* CONFIG_NOBQFMAN */ 656 657 #ifdef CONFIG_SYS_DPAA_FMAN 658 #define CONFIG_FMAN_ENET 659 #define CONFIG_PHYLIB_10G 660 #define CONFIG_PHY_VITESSE 661 #define CONFIG_PHY_REALTEK 662 #define CONFIG_PHY_TERANETICS 663 #define RGMII_PHY1_ADDR 0x1 664 #define RGMII_PHY2_ADDR 0x2 665 #define FM1_10GEC1_PHY_ADDR 0x3 666 #define SGMII_CARD_PORT1_PHY_ADDR 0x1C 667 #define SGMII_CARD_PORT2_PHY_ADDR 0x1D 668 #define SGMII_CARD_PORT3_PHY_ADDR 0x1E 669 #define SGMII_CARD_PORT4_PHY_ADDR 0x1F 670 #endif 671 672 #ifdef CONFIG_FMAN_ENET 673 #define CONFIG_MII /* MII PHY management */ 674 #define CONFIG_ETHPRIME "FM1@DTSEC3" 675 #endif 676 677 /* 678 * SATA 679 */ 680 #ifdef CONFIG_FSL_SATA_V2 681 #define CONFIG_LIBATA 682 #define CONFIG_FSL_SATA 683 #define CONFIG_SYS_SATA_MAX_DEVICE 2 684 #define CONFIG_SATA1 685 #define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR 686 #define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA 687 #define CONFIG_SATA2 688 #define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR 689 #define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA 690 #define CONFIG_LBA48 691 #endif 692 693 /* 694 * USB 695 */ 696 #ifdef CONFIG_USB_EHCI_HCD 697 #define CONFIG_USB_EHCI_FSL 698 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET 699 #define CONFIG_HAS_FSL_DR_USB 700 #endif 701 702 /* 703 * SDHC 704 */ 705 #ifdef CONFIG_MMC 706 #define CONFIG_FSL_ESDHC 707 #define CONFIG_FSL_ESDHC_USE_PERIPHERAL_CLK 708 #define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR 709 #define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT 710 #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33 711 #define CONFIG_FSL_ESDHC_ADAPTER_IDENT 712 #endif 713 714 /* 715 * Dynamic MTD Partition support with mtdparts 716 */ 717 #ifdef CONFIG_MTD_NOR_FLASH 718 #define CONFIG_MTD_DEVICE 719 #define CONFIG_MTD_PARTITIONS 720 #define CONFIG_FLASH_CFI_MTD 721 #endif 722 723 /* 724 * Environment 725 */ 726 #define CONFIG_LOADS_ECHO /* echo on for serial download */ 727 #define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ 728 729 /* 730 * Miscellaneous configurable options 731 */ 732 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 733 #define CONFIG_CMDLINE_EDITING /* Command-line editing */ 734 #define CONFIG_AUTO_COMPLETE /* add autocompletion support */ 735 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 736 737 /* 738 * For booting Linux, the board info and command line data 739 * have to be in the first 64 MB of memory, since this is 740 * the maximum mapped by the Linux kernel during initialization. 741 */ 742 #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial map for Linux*/ 743 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 744 745 #ifdef CONFIG_CMD_KGDB 746 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ 747 #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ 748 #endif 749 750 /* 751 * Environment Configuration 752 */ 753 #define CONFIG_ROOTPATH "/opt/nfsroot" 754 #define CONFIG_BOOTFILE "uImage" 755 #define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server */ 756 757 /* default location for tftp and bootm */ 758 #define CONFIG_LOADADDR 1000000 759 #define __USB_PHY_TYPE utmi 760 761 #define CONFIG_EXTRA_ENV_SETTINGS \ 762 "hwconfig=fsl_ddr:" \ 763 "ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) "," \ 764 "bank_intlv=auto;" \ 765 "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\ 766 "netdev=eth0\0" \ 767 "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ 768 "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \ 769 "tftpflash=tftpboot $loadaddr $uboot && " \ 770 "protect off $ubootaddr +$filesize && " \ 771 "erase $ubootaddr +$filesize && " \ 772 "cp.b $loadaddr $ubootaddr $filesize && " \ 773 "protect on $ubootaddr +$filesize && " \ 774 "cmp.b $loadaddr $ubootaddr $filesize\0" \ 775 "consoledev=ttyS0\0" \ 776 "ramdiskaddr=2000000\0" \ 777 "ramdiskfile=t2080qds/ramdisk.uboot\0" \ 778 "fdtaddr=1e00000\0" \ 779 "fdtfile=t2080qds/t2080qds.dtb\0" \ 780 "bdev=sda3\0" 781 782 /* 783 * For emulation this causes u-boot to jump to the start of the 784 * proof point app code automatically 785 */ 786 #define CONFIG_PROOF_POINTS \ 787 "setenv bootargs root=/dev/$bdev rw " \ 788 "console=$consoledev,$baudrate $othbootargs;" \ 789 "cpu 1 release 0x29000000 - - -;" \ 790 "cpu 2 release 0x29000000 - - -;" \ 791 "cpu 3 release 0x29000000 - - -;" \ 792 "cpu 4 release 0x29000000 - - -;" \ 793 "cpu 5 release 0x29000000 - - -;" \ 794 "cpu 6 release 0x29000000 - - -;" \ 795 "cpu 7 release 0x29000000 - - -;" \ 796 "go 0x29000000" 797 798 #define CONFIG_HVBOOT \ 799 "setenv bootargs config-addr=0x60000000; " \ 800 "bootm 0x01000000 - 0x00f00000" 801 802 #define CONFIG_ALU \ 803 "setenv bootargs root=/dev/$bdev rw " \ 804 "console=$consoledev,$baudrate $othbootargs;" \ 805 "cpu 1 release 0x01000000 - - -;" \ 806 "cpu 2 release 0x01000000 - - -;" \ 807 "cpu 3 release 0x01000000 - - -;" \ 808 "cpu 4 release 0x01000000 - - -;" \ 809 "cpu 5 release 0x01000000 - - -;" \ 810 "cpu 6 release 0x01000000 - - -;" \ 811 "cpu 7 release 0x01000000 - - -;" \ 812 "go 0x01000000" 813 814 #define CONFIG_LINUX \ 815 "setenv bootargs root=/dev/ram rw " \ 816 "console=$consoledev,$baudrate $othbootargs;" \ 817 "setenv ramdiskaddr 0x02000000;" \ 818 "setenv fdtaddr 0x00c00000;" \ 819 "setenv loadaddr 0x1000000;" \ 820 "bootm $loadaddr $ramdiskaddr $fdtaddr" 821 822 #define CONFIG_HDBOOT \ 823 "setenv bootargs root=/dev/$bdev rw " \ 824 "console=$consoledev,$baudrate $othbootargs;" \ 825 "tftp $loadaddr $bootfile;" \ 826 "tftp $fdtaddr $fdtfile;" \ 827 "bootm $loadaddr - $fdtaddr" 828 829 #define CONFIG_NFSBOOTCOMMAND \ 830 "setenv bootargs root=/dev/nfs rw " \ 831 "nfsroot=$serverip:$rootpath " \ 832 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 833 "console=$consoledev,$baudrate $othbootargs;" \ 834 "tftp $loadaddr $bootfile;" \ 835 "tftp $fdtaddr $fdtfile;" \ 836 "bootm $loadaddr - $fdtaddr" 837 838 #define CONFIG_RAMBOOTCOMMAND \ 839 "setenv bootargs root=/dev/ram rw " \ 840 "console=$consoledev,$baudrate $othbootargs;" \ 841 "tftp $ramdiskaddr $ramdiskfile;" \ 842 "tftp $loadaddr $bootfile;" \ 843 "tftp $fdtaddr $fdtfile;" \ 844 "bootm $loadaddr $ramdiskaddr $fdtaddr" 845 846 #define CONFIG_BOOTCOMMAND CONFIG_LINUX 847 848 #include <asm/fsl_secure_boot.h> 849 850 #endif /* __T208xQDS_H */ 851