1 /* SPDX-License-Identifier: GPL-2.0+ */
2 /*
3  * (C) Copyright 2016 Allied Telesis <www.alliedtelesis.co.nz>
4  */
5 
6 #ifndef _CONFIG_SBX81LIFXCAT_H
7 #define _CONFIG_SBX81LIFXCAT_H
8 
9 /*
10  * High Level Configuration Options (easy to change)
11  */
12 #define CONFIG_FEROCEON_88FR131	1	/* CPU Core subversion */
13 #define CONFIG_KW88F6281	1	/* SOC Name */
14 #define CONFIG_SKIP_LOWLEVEL_INIT	/* disable board lowlevel_init */
15 #define CONFIG_SYS_KWD_CONFIG	$(CONFIG_BOARDDIR)/kwbimage.cfg
16 #define CONFIG_BUILD_TARGET	"u-boot.kwb"
17 
18 /* additions for new ARM relocation support */
19 #define CONFIG_SYS_SDRAM_BASE	0x00000000
20 
21 #define CONFIG_MD5	/* get_random_hex on krikwood needs MD5 support */
22 #define CONFIG_KIRKWOOD_EGIGA_INIT	/* Enable GbePort0/1 for kernel */
23 #define CONFIG_KIRKWOOD_PCIE_INIT	/* Enable PCIE Port0 */
24 #define CONFIG_KIRKWOOD_RGMII_PAD_1V8	/* Set RGMII Pad voltage to 1.8V */
25 #define CONFIG_KIRKWOOD_GPIO	1
26 
27 /*
28  * NS16550 Configuration
29  */
30 #define CONFIG_SYS_NS16550
31 #define CONFIG_SYS_NS16550_SERIAL
32 #define CONFIG_SYS_NS16550_REG_SIZE	(-4)
33 #define CONFIG_SYS_NS16550_CLK		CONFIG_SYS_TCLK
34 #define CONFIG_SYS_NS16550_COM1		KW_UART0_BASE
35 
36 /*
37  * Serial Port configuration
38  * The following definitions let you select what serial you want to use
39  * for your console driver.
40  */
41 
42 #define CONFIG_CONS_INDEX	1	/*Console on UART0 */
43 
44 /*
45  * For booting Linux, the board info and command line data
46  * have to be in the first 8 MB of memory, since this is
47  * the maximum mapped by the Linux kernel during initialization.
48  */
49 #define CONFIG_CMDLINE_TAG	1	/* enable passing of ATAGs */
50 #define CONFIG_INITRD_TAG	1	/* enable INITRD tag */
51 #define CONFIG_SETUP_MEMORY_TAGS 1	/* enable memory tag */
52 
53 #define MTDPARTS_DEFAULT "mtdparts=spi0.0:768K(boot)ro,256K(boot-env),14M(user),1M(errlog)"
54 #define MTDPARTS_MTDOOPS "errlog"
55 #define CONFIG_DOS_PARTITION
56 
57 /*
58  *  Environment variables configurations
59  */
60 #define CONFIG_ENV_SPI_BUS		0
61 #define CONFIG_ENV_SPI_CS		0
62 #define CONFIG_ENV_SPI_MAX_HZ		20000000	/* 20Mhz */
63 #define CONFIG_ENV_SPI_MODE		CONFIG_SF_DEFAULT_MODE
64 #define CONFIG_ENV_SECT_SIZE		0x40000		/* 256K */
65 #define CONFIG_ENV_SIZE			0x02000
66 #define CONFIG_ENV_OFFSET		0xc0000		/* env starts here - 768K */
67 
68 /*
69  * U-Boot bootcode configuration
70  */
71 
72 #define CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for monitor */
73 #define CONFIG_SYS_MALLOC_LEN		  (4 << 20)	/* Reserve 4.0 MB for malloc */
74 
75 /*
76  * For booting Linux, the board info and command line data
77  * have to be in the first 8 MB of memory, since this is
78  * the maximum mapped by the Linux kernel during initialization.
79  */
80 #define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Mem map for Linux*/
81 
82 /* size in bytes reserved for initial data */
83 
84 #include <asm/arch/config.h>
85 /* There is no PHY directly connected so don't ask it for link status */
86 #undef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
87 
88 /*
89  * Other required minimal configurations
90  */
91 #define CONFIG_ARCH_CPU_INIT	/* call arch_cpu_init() */
92 #define CONFIG_SYS_MEMTEST_START 0x00400000	/* 4M */
93 #define CONFIG_SYS_MEMTEST_END	0x007fffff	/*(_8M -1) */
94 #define CONFIG_SYS_RESET_ADDRESS 0xffff0000	/* Rst Vector Adr */
95 
96 /*
97  * Ethernet Driver configuration
98  */
99 #ifdef CONFIG_CMD_NET
100 #define CONFIG_NETCONSOLE	/* include NetConsole support */
101 #define CONFIG_NET_MULTI	/* specify more that one ports available */
102 #define CONFIG_MVGBE	/* Enable kirkwood Gbe Controller Driver */
103 #define CONFIG_MVGBE_PORTS	{1, 0}	/* enable a single port */
104 #define CONFIG_PHY_BASE_ADR	0x01
105 #define CONFIG_ENV_OVERWRITE	/* ethaddr can be reprogrammed */
106 #endif /* CONFIG_CMD_NET */
107 
108 #define CONFIG_SYS_LOAD_ADDR  0x1000000      /* default location for tftp and bootm */
109 
110 #endif /* _CONFIG_SBX81LIFXCAT_H */
111